VTech LS6001, LS6001-17 User Manual
User’s manual
T
Compatible with
Hearing Aid T-Coil
TIA-1083
LS6001/LS6001-13/LS6001-15/
LS6001-16/LS6001-17
DECT 6.0 accessory handset for use with
VTech model LS6191
Congratulations
on purchasing your new VTech product. Before using this telephone, please read
Important safety instructions on page 5 of this manual.
This manual has instructions on how to set up and register your new handset.
For complete instructions on using the handset, see the Abridged user’s manual
that came with your telephone base.
You may also view or download the online Complete user’s manual for a
full set of installation and operation instructions at www.vtechphones.com.
In Canada, visit www.vtechcanada.com.
Telephones identified with this logo have reduced noise and
interference when used with most T-coil equipped hearing
aids and cochlear implants. The TIA-1083 Compliant Logo is
a trademark of the Telecommunications Industry Association.
Used under license.
The ENERGY STAR® program (www.energystar.gov) recognizes
and encourages the use of products that save energy and help
protect our
the ENERGY STAR® label indicating it meets the latest energy
efficiency guidelines.
environment. We are proud to mark this product with
Register online to get an additional 3-month warranty!
Visit www.vtechphones.com.
Registration
Register your product online for enhanced
warranty support.
Product news
Learn about the latest VTech products.
BC
1
Battery Pack / Bloc-piles :
(2.4V Ni-MH)
WARNING / AVERTISSEMENT :
DO NOT BURN OR PUNCTURE BATTERIES.
NE PAS INCINÉRER OU PERCER LES PILES.
Made in China / Fabriqué en chine
THIS SIDE UP / CE CÔTÉ VERS LE HAUT
Battery Pack / Bloc-piles :
(2.4V Ni-MH)
WARNING / AVERTISSEMENT :
DO NOT BURN OR PUNCTURE BATTERIES.
NE PAS INCINÉRER OU PERCER LES PILES.
Made in China / Fabriqué en chine
THIS SIDE UP / CE CÔTÉ VERS LE HAUT
Battery Pack / Bloc-piles :
(2.4V Ni-MH)
WARNING / AVERTISSEMENT :
DO NOT BURN OR PUNCTURE BATTERIES.
NE PAS INCINÉRER OU PERCER LES PILES.
Made in China / Fabriqué en chine
THIS SIDE UP / CE CÔTÉ VERS LE HAUT
Parts checklist
Batter
y
Pa
ck / Bloc
-piles
:
(2.4V Ni-MH)
WA
RNING / A
VERTISSEMENT
:
DO NO
T BURN OR PUNC
TURE BA
T
TERIES
.
NE
PA
S INCINÉRER OU PERCER LES PILES.
Made in China /
Fa
briqué en chin
e
THIS
SIDE
UP
/
CE
CÔ
TÉ
VERS
LE
HA
UT
Your telephone package contains the following items. Save your sales receipt and
original packaging in the event warranty service is necessary.
Handset
Charger and adapter
Battery
Battery installation
Install the battery as shown below.
Insert the battery connector
1.
securely into the socket as
shown below.
User’s manual
User’s manual
Place the battery with the label
2.
THIS SIDE UP facing up and the
wires inside the battery compartment.
Battery compartment
cover
Slide the battery compartment
3. Place the handset on the charger
cover towards the center of the
4.
to charge.
handset until it clicks into place.
CHARGE light
remains on when
charging.
If the handset will not be used for a long time, disconnect and remove the battery
•
to prevent possible leakage.
To purchase a replacement battery, visit our website at www.vtechphones.com
•
or call 1 (800) 595-9511. In Canada, go to www.vtechcanada.com or call
1 (800) 267-7377.
2
Battery charging
Once you have installed the battery, the screen indicates the battery status
(see the table below). For best performance, keep the handset in the telephone
base or charger when not in use. The battery is fully charged after 11 hours of
continuous charging.
Battery indicators Battery status Action
The screen is blank, or
displays Put in charger
and flashes.
The screen displays
Low battery and
flashes.
The screen displays
HANDSET X.
When it is fully charged, you can expect the following performance:
Operation Operating time
While in handset use (talking*) Seven hours
While in speakerphone mode (talking*) Three hours and 30 minutes
While not in use (standby**) Five days
* Operating times vary depending on your actual use and the age of the battery.
** Handset is not charging or in use.
The battery has no or very
little charge. The handset
cannot be used.
The battery has enough
charge to be used for a
short time.
The battery is charged. To keep the battery
Charge without
interruption (at least 30
minutes).
Charge without
interruption (about 30
minutes).
charged, place it in
the telephone base or
charger when not in use.
Add and register a handset
You can add new handsets (
purchased separately) to your telephone system. Each handset must be registered
with the telephone base before use. When first purchased and properly charged,
each expansion handset alternately displays To register HS... and ...see manual.
The new handset should be charged without interruption for at least 30 minutes
before registering it to the telephone base.
To register a handset:
At the bottom of the telephone base, press and hold
1.
/FIND HANDSET for about four seconds until
it shows Registering...
On the cordless handset, press then it
2.
shows Registering... Both the telephone base
and cordless handset show Registered and
you hear a beep when the registration process
completes. The registration process takes about
60 seconds to complete.
LS6001/LS6001-13/LS6001-15/LS6001-16/LS6001-17
Deregister handsets
If you want to replace a handset or reassign the designated handset number of
a registered handset, you must deregister all handsets and then deregister each
handset individually.
To deregister all handsets:
Press and hold /FIND HANDSET at the bottom of the telephone base for about
1.
10 seconds until the telephone base shows
Immediately press /FIND HANDSET again. You hear a confirmation tone.
2.
All handsets alternately show To register HS... and ...see manual. The
3.
deregistration process takes about 10 seconds to complete.
Registering... then De-register?
,
3
Loading...