VTech 2656 User Manual

Introduction

EXPAND YOUR v 2651 OR v 2656 SYSTEM. YOUR BASE CAN SUPPORT UP TO 4 HANDSETS!!!

IMPORTANT:

The v 2600 is an Accessory Handset for use with the v 2651 or v 2656 system. You must have one of these models in order to use this accessory Handset.

This manual is designed to familiarize you with the v 2600 Accessory Handset setup, registration and basic functions. For detailed operational instructions, please refer to the v 2651 or v 2656 User's Manuals.

To order additional system Handsets (model# v 2600), battery packs, or headsets, call VTech Communications, Inc. at 1-800-595-9511. In Canada, call 1-800-267-7377.

STOP!!

v 2600 manual.p65 8/27/2003, 11:02 AM1

If you have questions about this product, or if you're having difficulty with setup or operation, do not return your phone to the store. Call our Customer Support Center at:

In Canada, call 1-800-267-7377

1-800-595-9511

Important Safety Instructions

When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury, including the following:

1. Read and understand all instructions.

2. Follow all warnings and instructions marked on the product.

3. Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners

or aerosol cleaners. Use a damp cloth for cleaning.

4. Do not use this product near water (for example, near a bath tub, kitchen sink,

or swimming pool).

5. Do not place this product on an unstable cart, stand, or table. The product may

fall, causing serious damage to the product.

6. Slots and openings in the cabinet and the back or bottom are provided for ventilation.

To protect it from overheating, these openings must not be blocked by placing the product on the bed, sofa, rug, or other similar surface. This product should never be placed near or over a radiator or heat register. This product should not be placed in a built-in installation where proper ventilation is not provided.

7. This product should be operated only from the type of power source indicated on

the marking label. If you are not sure of the type of power supply to your home, consult your dealer or local power company.

8. Do not allow anything to rest on the power cord. Do not locate this product where

the cord will be abused by persons walking on it.

9. Never push objects of any kind into this product through cabinet slots as they may

touch dangerous voltage points or short out parts that could result in a risk of fire or electric shock. Never spill liquid of any kind on the product.

10. To reduce the risk of electric shock, do not disassemble this product, but take it

to a VTech authorized service facility. Opening or removing cabinet parts other than specified access doors may expose you to dangerous voltages or other risks. Incorrect reassembling can cause electric shock when the appliance is subsequently used.

11. Do not overload wall outlets and extension cords as this can result in the risk of

fire or electric shock.

12. Unplug this product from the wall outlet and refer servicing to VTECH under the

following conditions: A.When the power supply cord or plug is damaged or frayed. B.If liquid has been spilled into the product. C.If the product has been exposed to rain or water. D.If the product does not operate normally by following the operating instructions.

Adjust only those controls that are covered by the operating instructions, because improper adjustment of other controls may result in damage.

E.If the product has been dropped and the cabinet has been damaged. F.If the product exhibits a distinct change in performance.

13. Avoid using a telephone (other than a cordless type) during an electrical storm.

There may be a remote risk of electric shock from lighting.

14. Do not use the telephone to report a gas leak in the vicinity of the leak.

VTECH COMMUNICATIONS, INC.

Customer Service : 1-800-595-9511. In Canada, call VTech Telecommunications Canada Ltd . at 1-800-267-7377.

SAVE THESE INSTRUCTIONS

v 2600 manual.p65 8/27/2003, 11:02 AM2

Getting St arted

Setup

Installation of Battery Pack in Handset

Registration And Operation Of The VTECH v 2600 Accessory Handset

Your v 2651 or v 2656 system can support up to 4 Handsets. The accessory Handset v 2600 consists of the following:

Setup Of The v 2600 Accessory Handset

Follow the steps below:

1. Remove the battery cover by pressing

on the indent and sliding downward.

2. Align the two holes in plug with the

socket pins. Insert the plug into socket. Place the battery pack into the compartment with the wires in one of the lower corners, along the bottom of the battery pack.

3. Replace the battery cover by sliding

it upwards.

4. If the new battery pack is not already

charged, place the handset in the base unit, or a remote charging stand, and allow it to charge for 12 hours. After the first charge, a drained Handset battery pack will recharge in approximately 8 hours.

The original Handset that is shipped with your v 2651 or v 2656 will be automatically registered to the Base. This Handset is HANDSET 1.

As you register additional Handsets to the system, they will be assigned extension numbers in the following order: HANDSET 2 , HANDSET 3 , HANDSET 4 .

Whenever a Handset battery pack is installed, the Handset will automatically begin

SEARCHING FOR BASE (if previously registered), or it will prompt you to ENTER BASE ID to register the new Handset.

v 2600 manual.p65 8/27/2003, 11:02 AM3

1. Plug the AC power adapter into an

electrical outlet.

2. Install the battery pack, as described

on the following page.

BEFORE USING YOUR HANDSET(S), CAREFULLY PEEL OFF THE PROTECTIVE FILM, COVERING THE DISPLAY.

Registration

The Handset Layout

NOTE: Your Handset that comes with the v 2651/2656 system is registered to the Base at the factory. The following steps are for registration of additional Handsets (model# v 2600):

Enter Base ID Code

1. After charging the Handset, remove it from its

Charge Cradle. If the screen will displays SEARCHING FOR BASE, press NEW. If the screen displays ENTER BASE ID, go to step 2.

2. Enter the 15 digit Base ID Code, located on the

underside of the Base Unit. The ID Code can include numbers (0-9) and characters (*).

3. Press OK. The Handset will display: PLEASE

WAIT!!

Then put the Handset onto the cradle.

4. Wait approximately 15 seconds. The Handset will

display:

FOUND BASE NOTE: Occasionally, it will take longer than 15

second for the Handset to find the Base Unit. This is normal.

If the Handset displays: BASE BUSY TRY LATER, this indicates that the system is in use. Wait until the Base Unit is in the idle (on hook) mode, and repeat steps 2 to 4.

1. Antenna

2. Earpiece

3. Scroll Keys

4. Headset Jack (2.5mm)

8. LCD Display

9. Select/Menu

10. Off (Clear)

11. Intercom

Congratulations! You can now enjoy the benefits of your VTech multi-Handset system.

v 2600 manual.p65 8/27/2003, 11:02 AM4

5. On (Flash)

6. Dialing Keys (0-9, *, #)

7. Handsfree Speakerphone

12. Microphone

+ 7 hidden pages