VQ VQAO41G, VQA041B Instruction Manual
RADIO CONTROL MODEL
INSTRUCTION MANUAL
SPECIFICATIONS
Wingspan.......58.5 in. / 149cm
Length............45.2 in. / 115cm
Engine............40~46 2T / 52~70 4T
Or Electric equivalent.
WARNING!
This radio control model is not a toy. If modified or flow carelessly it could go out
of control and cause serious bodily injury or property damage.
Before flying your airplane, ensure the air field is spacious enough.
Always fly it outdoors in safe areas with no debris or obstacles.
HURRICANE
AlL BALSA AND Almost ready to fly
RC Functions:
Throtle - Rudder - Elevator
Aileron - Retract landing gear
VQAO41G
VQA041B
1.5mm
A
B
!
CA
L/R
Assemble left and right
sides the same way.
X
Drill holes using the stated
size of drill
(in this case 1.5 mm Ø)
Use epoxy glue
Take particular care here
Hatched-in areas:
remove covering
film carefully
Not included.
These parts must be
purchased separately
Check during assembly that these
parts move freely, without binding
Apply cyano glue
The pre-covered film on ARF kit may wrinkle due to variations
of temperature. Smooth out as explained right.
* Use an iron or heat gun. Start as low setting. Increase the
setting if necsessary. If it is too high, you may damage the
film
Low setting
SILICON
EPOXY A
EPOXY B
CA
GLUE
Epoxy Glue ( 5 minute type)
Silicon sealer
Cyanoacrylate
Glue
Minimum 5 channel radio
for airplane with 5 servos
.60 ~.70 - 4 cycle
10.5x6 for .40 - 2 cycle engine
11x6 for .46 - 2 cycle engine
12x6 for .60 - 4 cycle engine
12x7 for .70 - 4 cycle engine
13x8 - Brushless Motor
Silicone tube
Extension for aileron
servo, retract servo.
.46 ~ .50 - 2 cycle
REQUIRED FOR OPERATION (Purchase separately)
Linkage Stopper x2
(for retract servo)
Epoxy Glue (30 minute type)
TOLLS REQUIRED
Hobby knife
Needle nose Pliers
Phillip screw driver
Awl
Scissors
Wire Cutters
(Purchase separately)
Hex Wrench
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
Sander
Masking tape - Straight Edged Ruler - Pen or pencil - Rubbing alcohol - Drill and Assorted Drill Bits
Read through the manual before you begin, so you will have an overall idea of what to do.
Symbols used throughout this instruction manual, comprise:
(Purchase separately)
Retract landing
gear
VQAR05
Retract servo
x1
.Motor control x1 .Aileron x2
.Elevator x1 .Rudder x1
G-46 HP
Brushless Motor
or equivalent.
Brushless
Motor Control
5 cell 4500mAh.
CONVERSION TABLE
1.0mm = 3/64”
1.5mm = 1/16”
2.0mm = 5/64”
2.5mm = 3/32”
3.0mm = 1/8”
4.0mm = 5/32”
5.0mm = 13/64”
6.0mm = 15/64”
10mm = 13/32”
12mm = 15/32”
15mm = 19/32”
20mm = 51/64”
25mm = 1”
30mm = 1-3/16”
45mm = 1-51/64”
2- Joining the wing
A
B
Center line
! Make sure to glue securely, If not properly glued, a failure
in flight may occur.
Use epoxy glue to bury the
opening
TOP VIEW
1- Using a pencil, mark the center of the brace.
2- Trial fit the wing joiner into one of the wing panels. It should insert smoothly up to the center line marked above.
3- Slide the other wing half onto the dihedral brace until the wing panel meet. If the fit is over tight, it may be necessary to
lightly sand the dihedral brace.
4- Check for the correct dihedral angle.
5- Mix up some 30 minute epoxy and apply a generous amount of epoxy into the wing joiner cavity of one wing half.
6- Coat one half of the dihedral brace with epoxy up to the center line. Install the epoxy-coated side of the dihedral brace
into the wing joiner cavity up to the center line, marking sure that the “V” of the dihedral brace is positioned correctly
7- Do the same way with the other wing half.
8- Carefully slide the wing halves together, ensuring that they are accurately aligned. Firmly press the two halves
together, allowing the excess epoxy to run out. Clean off the excess epoxy.
Binder clip
Nylon wing bolt
Rubber band
(both the top
and bottom)
IMPORTANT:
Please do not clean off the excess epoxy on the wing with strong solvent or pure alcohol, only use
kerosene to keep the colour of your model not fade.
Hole for the aileron extension
cord exit.
Using the thread (pre-installed at factory) to slide
the aileron extension cord into the wing half.
Thread (pre-installed at factory)
Secure one end of the
aileron extension cord
with adhesive tape
Do the same way with other wing half.
Note: The two wing halves roots must fit together perfectly.
Hold the wing halves together with binder
clip and rubber band (not include)
A
B
1- Joining the wing
WING - TOP VIEW
WING ROOT
2mm
3x20mm screw
(not included)
Retract pushrod
BOTTOM-VIEW
Trial fit the push rod into the wing. Join the pushrod to the retract
gear arm and trial fit the retract into the wing.
After checking that the retract works
smoothly, fix the retract on the wing
with 3x20mm self tapping screws.
Do the same way with other half wing.
5- Retract landing gear installation
Put the nylon ring
Retract push rod Retract gear arm
Retract pushrod
VQ-AR03 -160223
Retract (option)
VQ-AR03 -160223
Retract (option)
Plywood buffer
included with
retract set.
FRONT-VIEW
WING-TOP
X
Retract landing gear
servo
4- Servo Installation
TOP VIEW
3- Retract servo tray
TOP VIEW
Cut away only
the covering
Note: The head of servo should be positioned
toward the rear of the wing.
Install the retract servo onto the retract servo mount
and secure it in place with four screw (included with radio set).
BOTTOM
RETRACT SERVO INSTALLATION
1.5mm
1/16”
B
C
A
CENTER
WING
SECTION
CA
CA
CA
CA
BOTTOM
A
B
C
Retract servo tray installation
CENTER
WING
SECTION
Retract servo
mount
Retract servo
mount
Retract servo tray
1/8(3mm plywood)
Secure one end of the
aileron extension cord
with adhesive tape
RETRACT
SERVO
ABS Gear cover
L/R
1.5mm
ABS gear cover
2x5mm
self tapping
screw
Gear mount
CA
ABS gear strap
7- Fix gear installation
ABS wheel well cover (for fix gear)
CA
8- Main Wing
BOTTOM VIEW
BOTTOM VIEW
3x20mm screw
2x5mm screw
..........4
...........8
4mm collar
..........2
Plastic retainer
..........2
Plastic
retainer
Ply gear mount
plate x 2
Gear mount x 2
2mm
Main landing gear
2mm
3x12mm screw
Gear mount
1
3x20mm
Nylon gear
strap
2mm
2
3x20mm
Ply gear
mount flat
Square
plastic
2mm
3
3x20mm screw
..........8
3x12mm screw
......16
Nylon gear strap
.......4
3x20mm screw
Wing - bottom view
6- Fixed gear
4
Square plastic x 2
Loading...