VQ FW-190A FOCKE-WULF Building Instructions

170393

Semi scale model

90 Class

2-cycle engine

4-cycle engine

FW-190A

60 Class

11

Focke-Wulf

13

BUILDING INSTRUCTIONS / MONTAGEANLEITUNG

SPECIFICATIONS

Wingspan Length Flying weight Electric Motor Glow Engine Radio

Technische Daten

Spannweite Länge Fluggewicht Elektroantrieb Verbrennerantrieb Fernsteuerung

1610mm 1220mm

2900g

800 Watt (BOOST 60)

7,5cc 2T / 8,5cc 4-T

5 Channel / 6 Servos

1610mm 1220mm

2900g

800 Watt (BOOST 60)

7,5cc 2T / 8,5cc 4T

5 Kanal / 6 Servos

WARNING! This radio controlled model is NOT a toy. If modified or flown carelessly it could go out of controll and cause serious human injury or property damage. Before flying your airplane, ensure the air field is spacious enough. Always fly it outdoors in safe areas and seek professional advice if you are unexperienced.

ACHTUNG! Dieses ferngesteuerte Modell ist KEIN Spielzeug! Es ist für fortgeschrittene Modellflugpiloten bestimmt, die ausreichende Erfahrung im Umgang mit derartigen Modellen besitzen Bei unsachgemäßer Verwendung kann hoher Personen- und/oder Sachschaden entstehen. Fragen Sie in einem Modellbauverein in Ihrer Nähe um professionelle Unterstützung, wenn Sie Hilfe im Bau und Betrieb benötigen. Der Zusammenbau dieses Modells ist durch die vielen Abbildungen selbsterklärend und ist für fortgeschrittene, erfahrene Modellbauer bestimmt.

1.5mm

A

B

!

CA

L/R

Assemble left and right sides the same way.

X

Drill holes using the stated

size of drill (in this case 1.5 mm Ø)

Use epoxy glue

Take particular care here

Hatched-in areas: remove covering film carefully

Not included. These parts must be

purchased separately

Check during assembly that these

parts move freely, without binding

Apply cyano glue

Low setting

SILICON

EPOXY A

EPOXY B

CA

GLUE

Epoxy Glue ( 5 minute type)

Silicon sealer

Cyanoacrylate Glue

Minimum 6 channel radio for airplane with 6 servos

.90 - 4 cycle

12x6 for .60 - 4 cycle engine 13x7 for .90 - 4 cycle engine 14X8 for Quantum 4120/07

Silicone tube

Extension for aileron servo, retract servo.

.60 - 2 cycle

REQUIRED FOR OPERATION (Purchase separately)

Linkage Stopper x2 (for retract servo)

Epoxy Glue (30 minute type)

TOLLS REQUIRED

Hobby knife

Needle nose Pliers

Phillip screw driver

Awl

Scissors

Wire Cutters

(Purchase separately)

Hex Wrench

.........................................................

Sander

Masking tape - Straight Edged Ruler - Pen or pencil - Rubbing alcohol - Drill and Assorted Drill Bits

Read through the manual before you begin, so you will have an overall idea of what to do.

Symbols used throughout this instruction manual, comprise:

(Purchase separately)

Retract landing gear

VQAR010

Retract servo x1

.Motor control x1 .Aileron x2 .Elevator x1 .Rudder x1 .Flap x 1

Brushless Motor BOOST 60

Phoenix-60 Brushless Motor Control or equivalent.

Li-Po Battery, 14.8V, 4500mAH (25C)

CONVERSION TABLE

1.0mm = 3/64”

1.5mm = 1/16”

2.0mm = 5/64”

2.5mm = 3/32”

3.0mm = 1/8”

4.0mm = 5/32”

5.0mm = 13/64”

6.0mm = 15/64”

10mm = 13/32” 12mm = 15/32” 15mm = 19/32” 20mm = 51/64”

25mm = 1” 30mm = 1-3/16” 45mm = 1-51/64”

If exposed to direct sunlight and/or heat, wrinkels can appear. Storing the model in a cool place will let the wrinkles disappear. Otherwise, remove wrinkles in covering film with a hair dryer, starting with low temperature. You can fix the corners by using a hot iron.

Bei Sonneneinstrahlung und/oder Wärme kann die Folie erschlaffen bzw. Falten entstehen. Verwenden Sie ein Warumluftgebläse (Haartrockner) um evtl. Falten aus der Folie zu bekommen. Die Kanten können Sie mit einem Bügeleisen behandeln. Nicht zuviel Hitze anwenden !

1- Joining the wing

1- Using a pencil, mark the center of the brace. 2- Trial fit the wing joiner into one of the wing panels. It should insert smoothly up to the center line marked above. 3- Slide the other wing half onto the dihedral brace until the wing panel meet. If the fit is over tight, it may be necessary to lightly sand the dihedral brace. 4- Check for the correct dihedral angle. 5- Mix approximately 30 minute epoxy and apply a generous amount of epoxy into the wing joiner cavity of one wing half. 6- Coat one half of the dihedral brace with epoxy up to the center line. Install the epoxy-coated side of the dihedral brace into the wing joiner cavity up to the center line, marking sure that the “V” of the dihedral brace is positioned correctly 7- Do the same way with the other wing half. 8- Carefully slide the wing halves together, ensuring that they are accurately aligned. Firmly press the two halves together, allowing the excess epoxy to run out. Clear off the excess epoxy.

Center line

TOP-VIEW

Cut away only the film

2- Retract servo mount

TOP-VIEW

A

B

C

B

C

A

CENTER WING SECTION

CA

BOTTOM

Retract servo tray

Retract servo mount

Retract servo mount “B”is longer than “C”

Note:

3- Retract servo

TOP-VIEW

CENTER WING SECTION

BOTTOM

Retract servo

X

Install the retract servo onto the retract servo mount and secure it in place with four screw (included with radio set).

Note: The head of servo should be positioned toward the rear of the wing.

RETRACT SERVO INSTALLATION

4- Flap servo

TOP-VIEW

WING SECTION

BOTTOM

Flap servo

X

Note: The head of servo should be positioned toward the front of the wing.

FLAP SERVO INSTALLATION

L/R

Flap rod

Retract servo

Flap servo

BOTTOM VIEW

5- Flap - Linkage

Flap rod

CLOSE POSITION

OPEN POSITION

35mm

1-13/32”

L/R

3x15mm screw

..........8

X

5/64”

BOTTOM VIEW

2mm

6- Retract landing gear

1

2

3

STEP

Note: Retract landing gear and Strut not included.

Main gear

WING SECTION

CLOSE POSITION

3x15mm screw

..........8

BOTTOM VIEW

7- Retract landing gear

RETRACTED

EXTENDED

Link the servo and retract gear arm with push rod. Be sure to adjust the stroke so that the landing gear locks in both up and down position.

With the retract and retract servo in the retracted position, mark the position where each of the pushrod will attach to the servo arm, a small piece of masking tape works well for this. Cut off the excess length each rod.

8- Fixed gear

Plastic strap

Main landing gear

Gear mount (hard wood)

Ply gear mount plate

Square plastic

3x10mm

Ply gear mount plate

Square plastic

Main gear (left)

Main gear (right)

Gear mount (hard wood)

Plastic strap

3x10mm screw..16

3x10mm screw

ABS gear cover

L/R

1.5mm

ABS gear cover

2x6mm screw

Gear mount (hard wood)

3x10mm screw

2x6mm screw

..........4

..........8

CA

ABS gear strap

BOTTOM VIEW

9- Fixed gear

VQ FW-190A FOCKE-WULF Building Instructions

Specifications and Main Features

Frequently Asked Questions

User Manual