Vox AC15 C1X, AC15CC1 User manual

AC15CC1

AC15CC1X

Owner’s Manual

Manuel d’utilisation

Bedienungsanleitung

Manual de Usuario

1SGFE

IMPORTANT SAFETY INSTRUCTIONS

• Read these instructions.

•Keep these instructions.

• Heed all warnings.

•Follow all instructions.

• Do not use this apparatus near water.

• Mains powered apparatus shall not be exposed to dripping or
splashing and that no objects filled with liquids, such as vases,
shall be placed on the apparatus.

• Clean only with dry cloth.

• Do not block any v entilation openings . Install in accordance with
the manufacturer's instructions.

• Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers) that
produce heat.

• Do not defeat the safety purpose of the polarized or grounding­type plug. A polarized plug has two blades with one wider than
the other. A grounding type plug has two blades and a third
grounding prong. The wide blade or the third prong are provided
for your safety. If the provided plug does not fit into your outlet,
consult an electrician for replacement of the obsolete outlet. (for
U.S.A. and Canada)

• Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the point
where they exit from the apparatus.

• Only use attachments/accessories specified by the manufacturer.

• Unplug this apparatus during lightning storms or when unused
for long periods of time.

•Turning off the power switch does not completely isolate this
product from the power line so remove the plug from the soc ket if
not using it for extended periods of time.

• Install this product near the wall socket and k eep the po w er plug
easily accessible.

•WARNING—This apparatus shall be connected to a mains
socket outlet with a protective earthing connection.

• Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way,
such as power-supply cord or plug is damaged, liquid has been
spilled or objects have f allen into the appar atus , the appar atus
has been exposed to rain or moisture, does not operate normally,
or has been dropped.

• Do not install this equipment on the far position from wall outlet
and/or convenience receptacle.

• Do not install this equipment in a confined space such as a box
for the conveyance or similar unit.

• Use only with the cart, stand, tripod, bracket, or table specified by
the manufacturer , or sold with the appar atus . When a cart is
used, use caution when moving the cart/apparatus combination
to avoid injury from tip-over.

The lightning flash with arrowhead symbol
within an equilateral triangle, is intended to
alert the user to the presence of uninsulated
“dangerous voltage” within the product's
enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.

The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the product.

CE mark for European Harmonized Standards

CE mark which is attached to our company’s products of A C mains
operated apparatus until December 31, 1996 means it conforms to
EMC Directive (89/336/EEC) and CE mark Directive (93/68/EEC).
And, CE mark which is attached after January 1, 1997 means it
conforms to EMC Directive (89/336/EEC), CE mark Directive (93/
68/EEC) and Low Voltage Directive (73/23/EEC).
Also, CE mark which is attached to our company’ s products of
Battery operated apparatus means it conforms to EMC Directive
(89/336/EEC) and CE mark Directive (93/68/EEC).

* Company names, product names, and names of f ormats etc. are
the trademarks or registered trademarks of their respective owners.

AALWAYS use the supplied mains lead, if a replacement is

required please contact your authorized Vox Dealer.

B DO NOT switch the amplifier on without a loudspeaker

connected.

C ENSURE that any extension cabinets used are of the correct

impedance.

D NEVER attempt to bypass the fuses or fit ones of the

incorrect values.

E DO NOT attempt to remove the amplifier chassis, there are

no user serviceable parts.

F Refer all servicing to qualified service personnel including

replacement of fuses and valves. Servicing is required when
the apparatus has been damaged in any way, such as when
the power supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the appara­tus has been exposed to rain or moisture, does not operate
normally or has been dropped.

CAUTION: Any changes or modifications not expressly approved

by the party responsible for compliance may void the users
authority to operate the equipment.

Note: It is recommended that all audio cables, with the exception

of the speaker lead, used to connect to the AC15 Custom
Classic are of a high quality, screened type. These should not
exceed 10 metres in length.
Always use a non-screened Vox approved speaker lead with
the AC15 Amplifier and extension cabinets.

WARNING: Do not obstruct ventilation grilles and always ensure

free movement of air around the amplifier!

2

INTRODUCTION

Congratulations on your purchase of the AC15 Custom Classic. This amp is the culmination of
years of manufacturing expertise in high quality, guitar amplifier design. We have taken the best AC15
designs, both old and new and added a number of useful and interesting features to give you the most
tonally flexible AC15 to date!

We’re confident you will find these improvements extremely useful and that your new amplifier will give you
many hours of tonal pleasure. Your AC15 is equipped with a number of modern features and conveniences
such as a master volume, global reverb and tremolo. Please read this manual carefully so that you can
familiarize yourself with these.

In order to ensure that this new AC15 meets exacting standards for tone, quality and reliability, it has been
built entirely in our vertically-integrated manufacturing facility, a facility capable of many processes not
usually found in guitar amplifier factories. We design and manufacture our own transformers, speakers
(except for the venerable Vox “Blue” made in the UK by Celestion), cabinets and electronics. What this
means to you is that the sound of your new AC15 Custom Classic is second to none.

There are two models in the range:

AC15CC1 that uses the VOX / Wharfedale custom GSH1230-16 speaker
AC15CC1X that uses the VOX / Celestion AlNiCo Blue loudspeaker

FRONT PANEL LAYOUT

1 2 3 4 5 6 7 8 9

1. Power Switch: This is the ON/OFF switch for the power to the amplifier.

Please ensure the amplifier is switched off and unplugged before being
moved.

2. Standby Switch: This switch allows the amplifier to attain the correct working temperature

before applying the H.T. supply.
Before connecting the amplifier to the Mains supply, ensure the Power and
Standby switches are in the off position.
Tu rn on the Power switch first and then wait 2–3 minutes before turning on
the Standby switch. Doing this each time you play helps prolong tube life.The
Standby switch is also very useful for playing live as it allows you to keep
the valves at a functional temperature between sets.

3

3. Master Volume: This controls the overall (Master) volume of your amplifier. Cleaner sounds

can be achieved by lowering the Volume and raising the Master. Setting
the Master lower and the Volume higher will give you a fatter, more dis­torted tone.As with all the controls of this amplifier, please experiment with
different configurations to find the tones that fit your playing style.

4. Tremolo Section: This section allows you to control the overall Tremolo by adjusting the Speed

and Depth. You can remotely switch the Tremolo On or Off with the sup-

plied VF002 footswitch.
Speed: As you might have guessed, this controls the speed of the built-in Tremolo.
Depth: This controls the depth (intensity) of the built-in tremolo.

5. Reverb Section: This section allows you to control the global Reverb level. You can remotely

switch the reverb On or Off with the supplied VF002 footswitch.

6. Bass: This controls the bass (low) frequencies in your sound - from warm and

light when turned down (counterclockwise) to dark and heavy when turned

up full (clockwise) and all points in-between.

7. Treble: This controls the treble (high) frequencies in your sound - from soft and

round when turned down (counterclockwise) to bright and cutting when

cranked (clockwise) and all points in-between.

8. Volume: This determines the sensitivity of the preamp section. Depending on where

this is set, you can either blend in more gain by turning it clockwise or you

can set it lower for a cleaner, “chimey” sound. This works directly with the

Master Volume meaning that if you keep this volume lower and the Master

higher, you will get a cleaner sound and conversely, if you keep this higher

and the Master lower you will get more gain.

9. Input: This is where you plug in your guitar.

REAR PANEL LAYOUT

1 2 3 4 5 6

1. Loudspeaker Output Jacks:

This is where you can hook up an external speaker cabinet(s) if desired.

2. Impedance Select Switch

Model AC15CC1

16 Ohm: Allows for the following configurations:

1) Set it to this if you use the internal 16ohm speaker only or 16ohm exter-

nal cabinet only.

4

8 Ohm: Allows for the following configurations:

1) Set it to this if you connect an extension cabinet. You’ll be running the
internal and external speaker in parallel. The impedance of the extension
cabinet must be 16 Ohms.

2) Set it to this if you connect an external 8 ohm cabinet and disconnect
the internal speaker.

Model AC15CC1X

This has an 8ohm loudspeaker internally fitted and the amplifier must be
set at 8ohm output. This speaker must be disconnected if amplifier is used
with an extension cabinet.

3. Footswitch jack: This is where you connect the supplied VF002 VOX footswitch so you can

turn the Reverb and Tremolo on and off.

4. HT Fuse: This fuse protects your amp should a fault occur with the power. The most

common reason for this fuse to blow is when an output tube becomes
faulty. The correct value of the HT fuse is located on the rear panel of the
amplifier and should only be replaced with one of the same value.

5. Mains Input: This is where the supplied, detachable Mains (power) cord is connected.

The specific mains input voltage rating that your amplifier needs to run at
is located on the rear panel of your amplifier. Before making any connec­tions or powering up the amplifier, make sure the correct voltage is set. If
you have any doubt, refer to your local VOX dealer.

6. Mains Fuse: This fuse provides an overall safety protection in the event your amplifier

develops and electrical fault. The correct value of the fuse is located on the
rear panel of your amplifier and should only be replaced with one of the
same value.

Specifications

Power Output: 15 Watts RMS into an 8 or 16 ohm loudspeaker load.
Internal speaker: 16 ohm, 12", 30 Watt VOX/Wharfedale Custom—model AC15CC1

8 ohm 12", 15 Watt VOX/Celestion AlniCo Blue—model AC15CC1X

Valve/tube complement:
Rectifier: silicon rectifier with passive SAG circuit.
Mains input: preset 100V or 120V or 230V or 240 V ~ 50 or 60 Hz depending on country

Mains Fuse value: 250V, T1.6AL for 100V / 250V, T1.25AL for 120V

HT Fuse: 250V, T250mAL.
Dimensions: 605 x 262 x 440 mm / 23.82" x 10.31" x 17.32"
Weight: AC15CC1: 21.6kg / 47.62 lbs. , AC15CC1X: 21.7kg / 47.84 lbs.
Included items: Power cable, VF002 footswitch

2 x EL84/6BQ5 & 2 x 12AX7/ECC83.

of sale. Please see Rating Plate on rear of amplifier for exact specification.

250V, T630mAL for either 230V & 240V.
Warning!—Replace fuse with same type and rating

Appearance and specifications of this product are subject to change without notice.

URL = http://www.voxamps.co.uk

5

INFORMATIONS IMPORTANTES DE SECURITE

• Lisez attentivement ces instructions.

•Veuillez conserver ces instructions.

• Observez tous les avertissements.

• Suivez toutes les consignes à la lettre.

• N’utilisez jamais cet appareil dans un endroit humide ni à
proximité d’eau.

•L’appareil alimenté par courant électrique ne peut pas être
exposé à des éclaboussures; évite en outre de placer des
récipients contenant des liquides, comme un vase (ou un verre
de bière), sur l’appareil.

• Nettoyez uniquement l’appareil avec un chiffon doux et sec.

• Ne bloquez jamais les orifices de ventilation de l’appareil et
installez-le toujours conformément aux instructions du fabricant.

• N’installez jamais l’appareil à proximité d’une source de chaleur ,
telle que des radiateurs, poêles ou tout autre dispositif (y compris
des amplificateurs) générant de la chaleur.

• N’essayez jamais de contourner le dispositif de sécurité d’une
prise de type polarisée ou d’une prise de terre. Une prise dite
polarisée dispose de deux broches, dont l’une est plus large que
l’autre. Une prise de terre comporte trois broches, dont une de
mise à la terre. Cette broche plus large ou broche de mise à la
terre vise à assurer votre sécurité. Si la fiche du cordon
d’alimentation ne correspond pas au type de prise de courant de
votre région, faites remplacer la prise obsolète par un électricien
qualifié (pour les Etats-Unis et le Canada).

• Placez toujours le cordon d’alimentation de sorte qu’on ne risque
pas de marcher dessus ni de le pincer. Cette précaution vise tout
spécialement la fiche du cordon et sa sortie de l’appareil.

• Utilisez exclusivement les fixations/accessoires préconisés par le
fabricant.

• S’il y a risque d’orage ou que vous ne comptez pas utiliser
l’appareil pendant une période prolongée, débranchez-le du
secteur.

• La mise sur OFF de l’interrupteur d’alimentation n’isole pas
totalement ce produit de la ligne secteur; aussi, retirez la fiche de
la prise s’il doit rester inutilisé pendant une période prolongée.

• Installez ce produit près de la prise électrique murale et gardez
un accès facile à la prise électrique et au cordon d’alimentation.

•ATTENTION: Cet appareil doit absolument être connecté à une
prise électrique reliée à la terre.

• Confiez tout travail de réparation uniquement à un S.A.V. qualifié.
Faites appel au S .A.V. si l’appareil a subi tout endommagement,
comme par exemple si sa fiche secteur ou son cordon
d’alimentation sont endommagés, si de l’eau ou des objets ont
pénétré à l’intérieur de l’appareil, si celui-ci a été exposé à la
pluie ou à la moisissure, s’il est tombé ou présente tout signe de
dysfonctionnement.

• N’utilisez jamais d’allonge trop longue avec cet appareil et ne
l’alimentez jamais via les prises secteur équipant d’autres
dispositifs.

• N’installez jamais cet appareil dans un endroit confiné comme
une caisse de transport ou tout autre récipient similaire.

• Utilisez l’appareil uniquement avec le chariot, stand, trépied,
fixation ou table spécifiés par le fabricant ou fourni av ec
l’appareil. Si v ous avez placé l’appareil sur un chariot, soyez très
prudent quand vous déplacez le chariot, afin d’éviter une chute et
des blessures.

Marque CE pour les normes européennes harmonisées

La marque CE apposée sur tous les produits de notre firme
fonctionnant sur secteur jusqu’au 31 décembre 1996 signifie que
ces appareils répondent à la Directive EMC (89/336/CEE) et à la
Directive concernant la marque CE (93/68/CEE).
La marque CE apposée après le 1 janvier 1997 signifie que ces
appareils sont conformes à la Directive EMC (89/336/CEE), à la
Directive concernant la marque CE (93/68/CEE) ainsi qu’à la
Directive Basse Tension (73/23/CEE).
La marque CE apposée sur tous les produits de notre firme
fonctionnant sur piles signifie que ces appareils répondent à la
Directive EMC (89/336/CEE) et à la Directive concernant la marque
CE (93/68/CEE).

* Les noms de sociétés, noms de produits et noms de f ormats, etc.

dans ce manuel sont des marques de fabrique ou des mar-ques
déposées de leurs propriétaires respectifs.

L’éclair dans le triangle est un symbole destiné
à attirer l’attention de l’utilisateur sur la
présence de parties non isolées et de “tension
dangereuse” à l’intérieur de l’appareil, qui
posent des risques d’électrocution pour
l’utilisateur.

Le point d’exclamation dans un triangle est un
symbole destiné à attirer l’attention de
l’utilisateur sur des sections de ce manuel
contenant des informations importantes, liées à
l’utilisation et à l’entretien de ce produit.

6