Vodavi Vodavi SIP Trunking Setup's SIP trunking on - Cbeyond SIPConnect - Config Guide 12-08

Configuration Guide

for SIPconnect service from

www.cbeyond.net

1-866-424-5100

The information contained in this document is specific to setting up SIPconnect

between Vertical SBX IP 320 and Cbeyond. If you require assistance with this

application, please contact Vertical Technical Support at 877-837-8422 or

http://www.vertical.com/support-login.html.

.

Cbeyond SIPconnect Trunk Configuration

Minimum System Requirements for SIP Trunk Setup

• SBX IP 320 system with a VOIP card (VOIB) installed

• PC Admin is required for programming SIP trunking attributes. After starting the PC

Admin program, select the program settings from the Menu List tab as indicated in Steps
1-9.

1.) Station Attribute 1 (PGM 111) – Program the SIP User ID Table that will correspond
with the SIP account (programmed later in SIP Attributes 2).

2.) CO Line List (PGM 140) – Program the VoIB trunks used for SIP integration as ISDN
DID. Cbeyond provides DID (Direct Inward Dialing) trunks.

Version 1.0 December 2008 2 of 6

Cbeyond SIPconnect Trunk Configuration

3.) CO Line ISDN Attributes (PGM 143) – Set the COLP and CLIP Table Idx fields to 0, set
the Call Type to Subscriber, the DID Conv Type to 2 (for integration with Flexible DID
Table, PGM 231), set the DID Remove Num to 7 (or other entry if the carrier is sending
more than 10 digits), and turn ISDN ENBLK Send to On.

4.) COLP Table (PGM 201) – Enter the COLP digits in Index 0 (this will correspond with
PGM 143 buttons 1 and 2). The COLP digits will most likely be the same as the
Authorization User Name in SIP Attributes 2.

Version 1.0 December 2008 3 of 6

Cbeyond SIPconnect Trunk Configuration

5.) Flexible DID Table (PGM 231) – Program the ring assignments for the DID routes in this
area. Use the last 3 digits of the inbound numbers that the SIP carrier provides as the
table numbers.

6.) Networking CO Line Attribute (PGM 322) – Enter the VoIB trunks used for the SIP
integration. Set the Networking CO Group to 0, the Networking CO Line Type to PSTN,
Gatekeeper Usage to Off, VoIP mode to SIP, and program DTMF Mode to Inband DTMF,
unless the carrier requires 2833.

Version 1.0 December 2008 4 of 6

Cbeyond SIPconnect Trunk Configuration

7.) VoIB/Gatekeeper Setting (PGM 340) – Program the IP Address, Gateway Address,
Subnet Mask and DNS address. Program the firewall address field only if you are using a
one-to-one NAT through firewall/router for the VoIB card. Set the VoIB mode to SIP
unless the system is networked with another system. If networked, set the VoIB to use
the DUAL option. Program the DTMF Mode so it matches the same field in PGM 322.

8.) SIP Attribute 1 – Program the Proxy Server Address, Proxy Registration Timer, Use
Outbound Proxy check box, Primary and Secondary DNS Addresses, and Domain
provided by Cbeyond. Enable the remaining checkboxes (Remote Party ID, 181 message
and SIP name service) if required by the Cbeyond activation technician.

Version 1.0 December 2008 5 of 6

Cbeyond SIPconnect Trunk Configuration

9.) SIP Attributes 2 – Select the index number you used in Station Attributes 1 (PGM 111)
Enter the User ID, Authentication User Name, Authentication User Password, and
Authentication User Password which is listed in the SIPconnect Settings section of the
Install Profile provided by your Cbeyond Service coordinator. Set User ID Registration to
register.

This completes the SIP Trunk configuration process.
If you need assistance please contact Vertical Technical Support
at 877-837-8422 or http://www.vertical.com/support-login.html.

For the latest product documentation on SBX IP 320, go to http://vconnect.vertical.com/

Version 1.0 December 2008 6 of 6