Vizio TL-R480T User Manual
COPYRIGHT & TRADEMARKS
Specifications are subject to change without notice. is a registered
trademark of TP-LINK Technologies Co., Ltd. Other brands and product names are
trademarks or registered trademarks of their respective holders.
No part of the specifications may be reproduced in any form or by any means or used to
make any derivative such as translation, transformation, or adaptation without permission
from TP-LINK Technologies Co., Ltd. Copyright © 2005 TP-LINK Technologies Co., Ltd.
All rights reserved.
SAFETY NOTICES
Caution: Do not use this product near water, for example, in a wet basement or near a
swimming pool.
Avoid using this product during an electrical storm. There may be a remote risk
of electric shock from lightning.
Package contents.............................................................................................................. 1
Chapter 1: About this Guide ........................................................................................... 2
1.1 Purposes ........................................................................................................... 2
1.2 Conventions ...................................................................................................... 2
1.3 Overview of this User Guide.............................................................................. 2
Chapter 2: Introduction ................................................................................................... 3
2.1 Overview of the Router...................................................................................... 3
2.2 Features ............................................................................................................ 3
2.3 Panel Layout ..................................................................................................... 4
2.3.1 The Front Panel....................................................................................... 4
2.3.2 The Rear Panel ....................................................................................... 5
Chapter 3: Connecting the Router.................................................................................. 6
3.1 System Requirements ....................................................................................... 6
3.2 Installation Environment Requirements ............................................................. 6
3.3 Connecting the Router....................................................................................... 6
Chapter 4: Quick Installation Guide................................................................................ 8
4.1 TCP/IP configuration ......................................................................................... 8
4.2 Quick Installation Guide..................................................................................... 9
Chapter 5: Configuring the Router................................................................................ 12
5.1 login................................................................................................................. 12
5.2 Status .............................................................................................................. 12
5.3 Quick Setup..................................................................................................... 13
5.4 Network ........................................................................................................... 13
5.4.1 LAN ....................................................................................................... 13
5.4.2 WAN...................................................................................................... 14
5.4.3 MAC Clone ............................................................................................ 19
5.4.4 Bandwidth Control ................................................................................. 20
5.4.5 VLAN..................................................................................................... 20
5.4.6 Port Mirror ............................................................................................. 20
5.5 DHCP .............................................................................................................. 21
5.5.1 DHCP Settings ...................................................................................... 21
5.5.2 DHCP Clients List.................................................................................. 22
5.5.3 Address Reservation ............................................................................. 23
5.6 Forwarding ...................................................................................................... 24
5.6.1 Virtual Servers....................................................................................... 24
5.6.2 Port Triggering....................................................................................... 25
5.6.3 DMZ ...................................................................................................... 27
5.6.4 UPnP..................................................................................................... 28
5.7 Security ........................................................................................................... 29
5.7.1 Firewall.................................................................................................. 29
5.7.2 IP Address Filtering ............................................................................... 30
5.7.3 Domain Filtering .................................................................................... 32
5.7.4 MAC Filtering......................................................................................... 33
5.7.5 Remote Management ............................................................................ 34
5.7.6 Advanced Security ................................................................................ 35
5.8 Static Routing .................................................................................................. 37
5.9 DDNS .............................................................................................................. 38
5.9.1 Oray.net DDNS ..................................................................................... 38
5.9.2 Comexe.cn DDNS ................................................................................. 39
5.10 System Tools ................................................................................................. 40
5.10.1 Time .................................................................................................... 41
5.10.2 Firmware ............................................................................................. 41
5.10.3 Factory Defaults .................................................................................. 42
5.10.4 Reboot................................................................................................. 42
5.10.5 Password ............................................................................................ 43
5.10.6 Log ...................................................................................................... 44
5.10.7 Statistics.............................................................................................. 44
Appendix A: FAQ .......................................................................................................... 46
Appendix B: Configuring the PCs ................................................................................. 49
Appendix C: Specifications........................................................................................... 54
Appendix D: Glossary................................................................................................... 55
Appendix E: Contact Information .................................................................................. 56
TL-R480T Enterprise Broadband Router User Giude
Package contents
The following contents should be found in your box:
One TL-R480T Enterprise Broadband Router
One power cord for TL-R480T Enterprise Broadband Router
One Resource CD for TL-R480T Enterprise Broadband Router, including:
• This Guide
• Other Helpful Information
Mounting fittings for installing in a standard 19” rack
Note: If any of the listed contents are damaged or missing, please contact the retailer
from whom you purchased the TL-R480T Enterprise Broadband Router for assistance.
- 1 -
TL-R480T Enterprise Broadband Router User Giude
Chapter 1: About this Guide
Thank you for choosing the TL-R480T Enterprise Broadband Router. This router
provides dedicated solutions for Internet café and small/medium/sizable enterprise with
volumes of users. With your network all connected, your local network can share Internet
access, files and fun for multiple PCs through one ISP account.
It is an easy, web-based setup for installation and management. Even though you may
not be familiar with the router, this guide will make configuring the router easy. Before
installing the router, please look through this guide to get to know all the router’s
functions.
1.1 Purposes
This Guide tells you how to use the TL-R480T Enterprise Broadband Router.
1.2 Conventions
The router mentioned in this guide stands for TL-R480T Enterprise Broadband Router.
1.3 Overview of this User Guide
Chapter 1: About this Guide
Chapter 2: Introduction
Chapter 3: Connecting the Router
Chapter 4: Quick Installation Guide
Chapter 5: Configuring the Router
Appendix A: FAQ
Appendix B: Configuring the PCs
Appendix C: Specifications
Appendix D: Glossary
Appendix E: Contact Information
- 2 -
TL-R480T Enterprise Broadband Router User Giude
Chapter 2: Introduction
2.1 Overview of the Router
The TL-R480T Enterprise Broadband Router possesses excellent throughput and driving
load capability, which more than meets the requirements for Internet cafés and
small/medium/sizable enterprises with volumes of users, making more efficient
communication. The superior performance will bring you a full-new experience of a
non-bottle-neck network.
TL-R480T Enterprise Broadband Router makes plenty of applications become a reality. It
can be used for constructing intranet FTP, WEB, and Mail server, etc, more inaccessibly.
It features network game ports, MSN audio conversation and special application settings.
Additionally, it provides bandwidth control, VLAN and Port Mirror, providing much more
additional value to your network.
Featuring firewall and VPN Passthrough, the TL-R480T Enterprise Broadband Router
resists most common Internet attacks and ensures secure data connectivity and
transmission over the Internet.
TL-R480T Enterprise Broadband Router is easy-to-manage. Quick Setup is supported
and friendly help messages are provided for every step. So you can configure it quickly
and share Internet access, files and fun comfortably.
2.2 Features
Complies with IEEE802.3, IEEE802.3u standards
Built in 4-port 10/100Mbps switch
Ethernet connection to a WAN device, such as a Cable modem or DSL modem
Shares data and Internet access for the network, connecting Internet through
PPPoE on demand and disconnecting when idle
Support Port Bandwidth Control, Port Mirror, Port-based VLAN for LAN ports
Built-in NAT and DHCP server supporting static IP address distributing
Provides 802.1x authentication for WAN port
Supports Virtual Server, Port Triggering, and DMZ host
Built-in firewall supporting IP address filtering, Domain Name filtering, and MAC
address filtering
Supports connecting/disconnecting Internet at a specified time of day
Supports access control, allowing parents and network administrators to establish
restricted access policies based on the time of day for children or staff
Supports TCP/IP, PPPoE, DHCP, ICMP, NAT, SNTP
Supports UPnP, Dynamic DNS, Static Routing, VPN pass-through
Supports Traffic Statistics
Supports ICMP-FLOOD, UDP-FLOOD, TCP-SYN-FLOOD filter
Ignores Ping packets from WAN or LAN ports
- 3 -
TL-R480T Enterprise Broadband Router User Giude
Supports firmware upgrade
Supports Remote and Web management
Rack-mountable steel case
2.3 Panel Layout
2.3.1 The Front Panel
The front panel of the TL-R480T consists of several LED indicators, which is designed to
indicate connections. Viewed from left to right. Table 2-1 describes the LEDs on the front
panel of the router.
1234
TL-R480T
Enterprise Broadband Router
Name Action Description
Power
Not lit No Power
Lit up Power on
M1
Not lit The router works properly
Lit up The router has a hardware error
Not lit The router has a hardware error
M2
Lit up The router has a hardware error
Flashing The router works properly
Not lit There is no device linked to the corresponding port
M1
POWER
M2
Figure 2-1: Front Panel sketch
M1 and M2 are flashing
synchronously, the router
is restoring the factory
default settings.
Link/Act
Lit up
There is a device linked to the corresponding port but no
activity
Flashing There is an active device linked to the corresponding port
100M
Not lit The linked device is running at 10Mbps
Lit up The linked device is running at 100Mbps
The LEDs description
The front panel contains the following features. (Viewed from left to right:)
Factory Default Reset button
There are two ways to reset the router's factory defaults:
1. Use the Factory Defaults function on System Tools -> Factory Defaults page in the
router's Web-based Utility.
2. Use the Factory Default Reset button: First, turn off the router's power. Second, press the
default reset button, then turn on the router's power, and hold the reset button until the M1
and M2 LED flash simultaneously (about 3 seconds). At last, release the reset button and
wait for the router to reboot.
Note: Ensure the router is powered on before it restarts completely.
Four LAN 10/100Mbps RJ45 ports for connecting the router to the local PCs
- 4 -
TL-R480T Enterprise Broadband Router User Giude
WAN RJ45 port for connecting the router to a cable, DSL modem or Ethernet
2.3.2 The Rear Panel
The rear panel of the TL-R480T only features a power receptacle, which is an AC power
receptacle. Connect the female of the power cord head here, and the male head to the
AC power outlet.
220V~ 50H z 0.1A
Figure 2-2: Rear Panel sketch
- 5 -
TL-R480T Enterprise Broadband Router User Giude
Chapter 3: Connecting the Router
3.1 System Requirements
Broadband Internet Access Service (DSL/Cable/Ethernet)
One DSL/Cable modem that has an RJ45 connector (It’s not necessary if you
connect the router to Ethernet)
Each PC on the LAN needs a working Ethernet Adapter and an Ethernet cable with
RJ45 connectors
TCP/IP protocol must be installed on each PC
Web browser, such as Microsoft Internet Explorer 5.0 or later, Netscape Navigator
6.0 or later
3.2 Installation Environment Requirements
Not in direct sunlight or near a heater or heating vent
Not cluttered or crowded. There should be at least 2 inches (5 cm) of clear space on
all sides of the router
Well ventilated (especially if it is in a closet)
Operating temperature: 0℃~40℃ (32℉~104℉)
Operating Humidity: 10%~90%RH, Non-condensing
3.3 Connecting the Router
Before you install the router, you should connect your PC to the Internet through your
broadband service successfully. If there is any problem, please contact with your ISP for
help. After that, please install the router according to the following steps. Don't forget to
pull out the power plug and keep your hands dry.
1. Power off your PC(s), Cable/DSL modem, and the router.
2. Connect the PC(s) and all Switches/Hubs on your LAN to the LAN Ports on the
router, shown in figure 3-1.
3. Connect the DSL/Cable modem to the WAN port on the router, shown in figure 3-1.
4. Connect the AC power adapter to the AC power socket on the router, and the other
end into an electrical outlet. The router will start to work automatically.
5. Power on your PC(s) and Cable/DSL modem.
- 6 -
TL-R480T Enterprise Broadband Router User Giude
TL-R480T
Enterprise Broadband Router
POWER
M1
M2
1234
To WAN
To LAN
Switch/Hub
（）
XDSL Cable Ethernet
、、
Figure 3-1 Hardware Installation of the TL-R480T Enterprise Broadband Router
- 7 -
TL-R480T Enterprise Broadband Router User Giude
Chapter 4: Quick Installation Guide
After connecting the TL-R480T router into your network, you should configure it. This
chapter describes how to configure the basic functions of your TL-R480T Enterprise
Broadband Router. These procedures only take you a few minutes. You can access the
Internet via the router immediately after it has been successfully configured.
4.1 TCP/IP configuration
The default IP address of the TL-R480T Enterprise Broadband Router is 192.168.1.1,
and the default Subnet Mask is 255.255.255.0. These values can be seen from the LAN,
and can be changed as your desire. As an example, we use the default values for
description in this guide.
Connect the local PCs to the LAN ports on the router. There are then two means to
configure the IP address for your PCs.
Configure the IP address manually
1) Set up the TCP/IP Protocol for your PC(s). If you need instructions as to how to
do this, please refer to
2) Configure the network parameters. The IP address is 192.168.1.xxx ("xxx" is
from 2 to 254), Subnet Mask is 255.255.255.0, and Gateway is 192.168.1.1
(The router's default IP address)
Obtain an IP address automatically
1) Set up the TCP/IP Protocol in "Obtain an IP address automatically" mode on
your PC(s). If you need instructions as to how to do this, please refer to
Appendix B: "Configuring the PCs."
2) Power off the router and PC(s). Then turn on the router, and restart the PC(s).
The built-in DHCP server will assign IP addresses for the PC(s).
Appendix B: "Configuring the PCs."
Now, you can run the Ping command in the command prompt to verify the network
connection between your PC(s) and the router. The following example is in Windows
2000.
Open a command prompt, and type ping 192.168.1.1, then press Enter.
Figure 4-1 Successful result of Ping command
If the result displayed is similar to what is shown in figure 4-1, the connection between
- 8 -
TL-R480T Enterprise Broadband Router User Giude
your PC and the router has been established.
Figure 4-2 Failed result of Ping command
If the result displayed is similar to what shown in figure 4-2, it means that your PC has
not connected to the router. If so, refer to the following steps for a solution.
1. Is the connection between your PC and the router correct?
Note: The Link/Act LEDs of LAN port on the router and LEDs on your PC's adapter
should be lit.
2. Is the TCP/IP configuration for your PC correct?
Note: If the router's IP address is 192.168.1.1, your PC's IP address must be within
the range of 192.168.1.2 ~ 192.168.1.254, the gateway must be 192.168.1.1
4.2 Quick Installation Guide
With a Web-based (Internet Explorer or Netscape® Navigator) utility, the TL-R480T
Enterprise Broadband Router is easy to configure and manage. The Web-based utility
can be used on any Windows, Macintosh or UNIX OS with a web browser.
Connect to the router by typing http://192.168.1.1 in the address field of web browser.
Figure 4-3 Login to the router
After a moment, a login window will appear similar to that shown in Figure 4-4. Enter
admin for the User Name and Password, both in lower case letters. Then click the OK
button or press the Enter key.
Figure 4-4 Login Windows
- 9 -
TL-R480T Enterprise Broadband Router User Giude
Note: If the above screen does not prompt, it means that your web-browser has been set
to a proxy. Go to Tools menu>Internet Options>Connections>LAN Settings, in the screen
that appears, cancel the Using Proxy checkbox, and click OK to finish it.
If the User Name and Password are correct, you can configure the router using the web
browser. Please click the Quick Setup link on the left of the main menu and the Quick
Setup screen will appear.
Figure 4-5 Quick Setup
Click Next, the Choose WAN Connection Type page will appear, shown in figure 4-6.
Figure 4-6 Choose WAN Connection Type
The router supports three popular ways to connect to Internet. Please select one
compatible with your ISP, if you are given another way not listed here, refer to
Network->WAN for detailed list. Click Next to enter the necessary network parameters.
If you choose "PPPoE", you will see this page shown in figure 4-7:
Figure 4-7 Quick Setup - PPPoE
User Name and Password - Enter the User Name and Password provided by your
- 10 -
TL-R480T Enterprise Broadband Router User Giude
ISP. These fields are case sensitive. If you have difficulty with this process, please
contact your ISP.
If you choose " Dynamic I P", the router will automatically receive the IP parameters from
your ISP without needing to enter any parameters.
If you Choose "Static IP", the Static IP settings page will appear, shown in figure 4-8:
Figure 4-8 Quick Setup - Static IP
Note: The IP parameters should have been provided by your ISP.
IP Address - This is the WAN IP address as seen by external users on the Internet
(including your ISP). Enter the IP address into the field.
Subnet Mask - The Subnet Mask is used for the WAN IP address, it is usually
255.255.255.0
Default Gateway - Enter the gateway into the box if required.
Primary DNS - Enter the DNS Server IP address into the boxes if required.
Secondary DNS - If your ISP provides another DNS server, enter it into this field.
Click the Next button, then you will see the Finish page:
Figure 4-9 Quick Setup - Finish
After finishing all configurations of basic network parameters, please click Finish button
to exit this Quick Setup.
- 11 -
TL-R480T Enterprise Broadband Router User Giude
Chapter 5: Configuring the Router
This chapter describes each web page's key functions.
5.1 login
After your successful login, you can configure and manage the router. There are nine main
menus on the left of the web-based utility. Submenus will be available after you click one
of the main menus. The nine main menus are: Status, Quick Setup, Network, DHCP,
Forwarding, Security, Static Routing, DDNS and System Tools. On the right of the
web-based utility, there are the detailed explanations and instructions for the
corresponding page. To apply any settings you have altered on the page, please click the
Save button.
There are the detailed explanations for each web page's key functions below.
5.2 Status
The Status page displays the router's current status and configuration. All information is
read-only.
1. LAN
This field displays the current settings or information for the LAN, including the MAC
address, IP address and Subnet Mask.
2. WAN
These parameters apply to the WAN port of the router, including MAC address, IP
address, Subnet Mask, Default Gateway, DNS server and WAN connection type.
If PPPoE is chosen as the WAN connection type, the Disconnect button will be
shown here while you are accessing the Internet. You can also cut the connection by
clicking the button. If you have not connected to the Internet, a Connect button will be
shown, you can then establish the connection by clicking the button.
3. Traffic Statistics
This field displays the router's traffic statistics.
4. System Up Time
The time of the router running from the time it is powered on or is reset.
- 12 -
TL-R480T Enterprise Broadband Router User Giude
Figure 5-1 Router Status
5.3 Quick Setup
Please refer to Section 4.2: "Quick Installation Guide."
5.4 Network
Figure 5-2 the Network menu
There are six submenus under the Network menu (shown in figure 5-2): LAN, WAN,
MAC Clone, Bandwidth Control, VLAN and Port Mirror. Click any of them, and you
will be able to configure the corresponding function. The detailed explanations for each
submenu are provided below.
5.4.1 LAN
You can configure the IP parameters of the LAN on this page.
- 13 -
TL-R480T Enterprise Broadband Router User Giude
Figure 5-3 LAN
MAC Address - The physical address of the router, as seen from the LAN. The
value can't be changed.
IP Address - Enter the IP address of your router in dotted-decimal notation (factory
default: 192.168.1.1).
Subnet Mask - An address code that determines the size of the network. Normally
use 255.255.255.0 as the subnet mask.
Note:
a. If you change the IP address of the LAN, you must use the new IP address to login
to the router.
b. If the new LAN IP Address you set is not in the same subnet, the IP Address pool in
the DHCP sever will not take effect, until they are re-configured.
c. If the new LAN IP Address you set is not in the same subnet, the Virtual Server and
DMZ Host may change accordingly at the same time, you’d better re-configure it as
well.
5.4.2 WAN
You can configure the WAN port parameters on this page.
First, please choose the WAN Connection Type (Dynamic IP/Static IP/PPPoE/802.1x +
Dynamic IP/802.1x + Static IP) to the Internet. The default type is PPPoE. If you aren’t
given any login parameters (fixed IP address, logging ID, etc), please select Dynamic
IP. If you are given a fixed IP (static IP), please select Static IP. If you are given a user
name and a password, please select PPPoE
. If you are not sure which connection type
you use currently, please contact your ISP to obtain the correct information.
1. If you choose Dynamic IP, the router will automatically get IP parameters from
your ISP. You can see the page as follows (figure 5-4):
- 14 -
Loading...