Vivotek FD8361L Installation Guide

FD8361L

Fixed Dome
Network Camera

Quick Installation Guide

繁中 日本語

English

IR Illuminators • 3-axis • Video Cropping • ePTZ

簡中

Français

Deutsch

Español Português

Italiano

Türkçe

Polski

Русский

Česky Svenska

Warning Before Installation

English

Power off the Network Camera as
soon as smoke or unusual odors are
detected.

Contact your distributor in the event of
occurrence.

Do not place the Network Camera on
unsteady surfaces.

Do not insert sharp or tiny objects
into the Network Camera.

Refer to your user's manual for the
operating temperature.

Do not touch the Network Camera
during a lightning storm.

Do not drop the Network Camera.

EN - 1

5

1

0

0

0

0

2

1

1

G

1

Package Contents

FD8361L

Bottom Base

Alignment Sticker / Ceiling Hole Template Sticker

Drill hole

Ceiling Hole Template Sticker

L-type Hex Key Wrench / RJ45 Female/Female Coupler / Silica Gel / Screws

Quick Installation Guide /
Warranty Card

Fixed Dome

FD8361L

Network Camera

Quick Installation Guide

Türkçe

繁中 日本語

簡中

Česky Svenska

Русский

Italiano

Deutsch

Français

Polski

English

Español Português

IR Illuminators • 3-axis • Video Cropping • ePTZ

Software CD

EN - 2

2

Physical Description

Inner View

English

Vari-focal Lens
(f= 3~9 mm)

SD/SDHC Card Slot

Status LED
Recessed Reset
Button

Focus Controller

Zoom Controller

Operating environment: -20° ~ 50°C

When the temparature inside the Network
Camera reaches over 50°C, the fan will operate
automatically; when the temparature inside the
Network Camera drops to 0°C, the heater and fan
will both operate automatically.

IR LEDs (18 units,

distance 20m)
Light Sensor
Rotation Adjustment

Screw

Tilt Adjustment Screw

Pan Adjustment Screw

NTSC/PAL Video Output
Switch

AC24V
AC24V

BNC Video Output
AC 24V Terminal Block

Ethernet 10/100 RJ45 Plug

Ground

Heater

Fan

EN - 3

Outer View

Camera Base

IP66-rated Vandal-proof
Dome Cover

AC24V
AC24V

c

b

a

IP66-rated Vandal-proof
Bottom Base

Record the MAC address under
the camera base before installing
the camera.

a

Hole a~c:
Holes to secure the bottom base.

Network Camera

Model No: FD8361L

MAC:0002D1083236

This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions:
(1)This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.

Pat. 6,930,709

EN - 4

RoHS

Made in Taiwan

c

V I

CLASS A

b

3

Hardware Installation

First, use a screwdriver to loose the three screws and detach the dome cover from the
camera base. Then, follow the steps below to install the camera to either a ceiling or a wall.

AC24V
AC24V

Ceiling mount (with the bottom base)

1. Attach the supplied alignment sticker to the ceiling.

2. Using the 10 circles on the sticker, drill at least 2 pilot holes symmetrically on each side into the ceil­ing. Then hammer the four supplied plastic anchors into the holes.

3. Through the four holes on the bottom base, insert the four supplied screws into the corresponding
holes and secure the bottom base with a screwdriver.

4. Feed the cables through hole A or B. If you want to use hole B, remove the rubber stopper with a
screwdriver.

5. Secure the camera base to the bottom base with three supplied screws.

English

A

1

2

B

4

3

5

EN - 5

Wall mount (with the bottom base)

1. Attach the supplied alignment sticker to the wall.

2. Using the 10 circles on the sticker, drill at least 2 pilot holes symmetrically on each side into the wall.
Then hammer the four supplied plastic anchors into the holes.

3. Using the four holes on the bottom base, insert the four supplied screws to corresponding holes and
secure the bottom base with a screwdriver.

4. Feed the cables through hole A or B. If you want to use hole B, remove the rubber stopper with a
screwdriver.

5. Secure the camera base to the bottom base with three supplied screws.

1

3

2

4

A

B

5

EN - 6

Drop-ceiling mount (without the bottom base)

1. Attach the supplied ceiling hole template sticker to the ceiling.

2. Open a hole along the inner circle of the sticker.

3. Using the 3 circles on the sticker, drill 3 pilot holes into the ceiling. Then hammer the three supplied
plastic anchors into the holes.

4. Mount the Network Camera to the ceiling and feed the cables through.

5. Using the three holes on the side of the camera base, insert the three supplied screws into the cor­responding holes and secure them with a screwdriver.

English

1

Drill hole

Ceiling Hole Template Sticker

Network Deployment

4

2

3

General Connection (without PoE)

1. Connect the power cable to the AC 24V terminal block.

AC24V
AC24V

AC24V: Power in AC 24V
AC24V: Power in AC 24V

AC24V
AC24V

4

5

L
I
N

POW

K

ER

C
O

LL

I

RE

S

ION

CEIVE

1

PARTITIO

2

3

N

4

5

2. Use the supplied RJ45 female/female coupler
to connect the Network Camera to a switch.

Use a Category 5 Cross Cable when Network

Camera is directly connected to PC.

EN - 7

Power over Ethernet (PoE)

When using a PoE-enabled switch

The Network Camera is PoE-compliant, allowing transmission of power and data via a
single Ethernet cable. Follow the below illustration to connect the Network Camera to a
PoE-enabled switch via Ethernet cable.

AC24V
AC24V

POWER

LINK

COLLISION

RECEIVE

1

2

PARTITION

3

4

5

PoE Switch

When using a non-PoE switch

Use a PoE power injector (optional) to connect between the Network Camera and a
non-PoE switch.

AC24V
AC24V

PoE Power Injector

(optional)

Non-PoE Switch

LINK

POWER

COLLISION

RECEIVE

1

2

PARTITION

3

4

5

EN - 8

5

Assigning an IP Address

1. Install “Installation Wizard 2” from the Software Utility directory on the software CD.

2. The program will conduct an analysis of your network environment. After your network is
analyzed, please click on the “Next” button to continue the program.

Installation

Wizard 2

3. The program will search for VIVOTEK Video Receivers, Video Servers, and Network
Cameras on the same LAN.

4. After searching, the main installer window will pop up. Click on the MAC that matches the
one labeled on the bottom of your device to connect to the Network Camera via Internet
Explorer.

English

Network Camera

Model No: FD8361L

MAC:0002D1083236

This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions:
(1)This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.

Pat. 6,930,709

RoHS

Made in Taiwan

V I

CLASS A

00-02-D1-08-32-36 192.168.5.109 FD8361L

0002D1083236

EN - 9

6

Ready to Use

1. Access the Network Camera from the LAN.

2. Retrieve live video through web browser or recording software.

For further setup, please refer to the user's manual on the software CD.

EN - 10

Adjusting the Lens

7

Based on the live image retrieved from the camera, adjust the camera lens by doing the
following:

To adjust the viewing angle -- 3-axis mechanism design

1. Loosen the pan adjustment screw and then turn the lens module left and right. Upon
completion, tighten the screw.

2. Loosen the tilt adjustment screws on both side of the camera and then turn the lens
module up and down. Upon completion, tighten the screws.

3. Loosen the rotation adjustment screw and then turn the lens to adjust the image
orientation. Upon completion, tighten screw.

English

Rotate the screw
Turn the lens

The sophisticated 3-axis mechanism

design offers very exible, easy hardware

installation for either ceiling or wall mount.

Loosen

1

Tighten

Loosen

Loosen

Pan 350°

2

Tilt 60°

Tighten

Tighten

Rotate 350°

3

To adjust the zoom factor and focus range

1. Loosen the zoom controller to adjust the zoom factor. Upon completion, tighten the zoom
controller.

2. Loosen the focus controller to adjust the focus range. Upon completion, tighten the focus
controller.

Loosen

W

T

N

Tighten

8

DO NOT over rotate the lens. Doing
so will damage the camera lens
module.

EN - 11

Completion

8

1. Rotate the black cover inside the dome cover to t the lens shooting direction.

2. Attach the dome cover to the camera.

3. Secure the three dome screws with the supplied screwdriver. Finally, make sure all parts

of the camera are securely installed.

2

1

3

3

3

EN - 12

P/N:625012601G Rev. 1.1

All specications are subject to change without notice.

c

Copyright 2012 VIVOTEK INC. All rights reserved.

VIVOTEK INC.

6F, No.192, Lien-Cheng Rd., Chung-Ho, New Taipei City, 235, Taiwan, R.O.C.

|T: [phone]| F: [phone]| E: [e-mail]

VIVOTEK USA, INC.

2050 Ringwood Avenue, San Jose, CA 95131

|T: 408-773-8686| F: 408-773-8298|E : [e-mail]