Vivotek FD8135H Installation Guide

FD8135H

Fixed Dome
Network Camera

Quick Installation Guide

繁中 日本語

English

720P HD • P-Iris • WDR Pro

簡中

Français

Español Português

Deutsch

Italiano

Türkçe

Polski

Русский

Česky Svenska

Warning Before Installation

English

Power off the Network Camera as
soon as smoke or unusual odors are
detected.

Contact your distributor in the event of
occurrence.

Do not place the Network Camera
around heat sources, such as a
television or oven.

Keep the Network Camera away from
direct sunlight.

Keep the Network Camera away
from water. If the Network Camera
becomes wet, power off immediately.

Contact your distributor in the event of
occurrence.

Refer to your user's manual for the
operating temperature.

Do not place the Network Camera in
high humidity environments.

EN - 1

Do not place the Network Camera on
unsteady surfaces.

Do not touch the Network Camera
during a lightning storm.

Do not disassemble the Network
Camera.

Do not insert sharp or tiny objects
into the Network Camera.

Do not drop the Network Camera.

EN - 2

5

1

0

0

0

0

2

1

1

G

1

Package Contents

FD8135H Alignment Sticker

English

Software CD

Quick Installation Guide /
Warranty Card

T10 Torx Screwdriver/ Screws /
Plastic Anchors / AV Cable

EN - 3

2

12 3 745 86

Ethernet

Micro SD Card

Audio InAV Out

Reset

Int.

NTSC

PAL

Ext.

1. AC24V_2

2. AC24V_1

3. DI 3+

4. DI 2+

5. DI 1+

6. DI- (GND)

7. DO-

8. DO+ (+12V)

Physical Description

Camera Front View

Camera Rear View

SDHC Card

Reset Button

Lens

Built-in

Microphone

Micro SD/

Slot

Light Sensor

PIR Sensor

Black Cover

IR LEDs

(18 units, effective up to 15m)

Focus Assist
Button

Reserved

NOTE:

The max. output load from
pins #7 and 8 is 50mA.

Jumpers

Microphone

internal

external

1 2

Video Output

NTSC

60Hz

PAL

50Hz

Audio/Video Out

(green)

Microphone In

(pink)

General IO Terminal

Block

10/100BaseT

Ethernet

EN - 4

3

Hardware Installation

English

Before installing your camera,
make sure the built-in PIR (Passive
Infrared Sensor) can be directed
toward the area of interest, where
possible intrusion may occur. (The
sensitivity of PIR sensor depends
on the object size and temperature
differences between the object and
the background environment.)

50

5m

50

Dome Cover

Top View

41

Bottom of the

5m

41

Side View

Camera

Remove the black cover as shown below so that you can ne-tune the focus and zoom the

camera later when the cabling is done.

Tilt Ajustment

Screw

EN - 5

Focus Ctrl
Zoom Ctrl

Wall Mount

Ceiling Mount

1. Attach the alignment sticker to the ceilling/wall.

2. Through the two circles on the sticker, drill two pilot holes into the ceilling/wall.

3. The Network Camera can be mounted with the cable routed through the ceiling/wall or
from the side. If you want to feed the cable through the ceiling/wall, drill a cable hole A
as shown in the above picture.

4. Hammer the supplied plastic anchors into the holes.

5. Align the two holes on each side of the camera base with the two plastic anchors on the
ceilling/wall, insert the supplied screws to corresponding holes and secure them with a
screwdriver.

Network Deployment

4

General Connection (without PoE)

1. If you have external DI devices, make the connection from general I/O terminal block.

2. Ethernet, power, and other cables are user-supplied.

3. Connect the AC cables from the terminal block as an alternate power source. The IO
cables are user-supplied.

NOTE:

Pin #1 & 2 AC 24V as alternate power are for
indoor use only

Ethernet

Switch

POW

ER

L
I

N
C
OLL

K

I

RE

S
ION

CEIVE

1

PARTITIO

2

3

N

4

5

Pin1 & 2 AC 24V

EN - 6

Power over Ethernet (PoE)

When using a PoE-enabled switch

This Network Camera is PoE-compliant, allowing transmission of power and data via a
single Ethernet cable. Follow the below illustration to connect the Network Camera to a
PoE-enabled switch via Ethernet cable.

NOTE:

1. This equipment is only to be connected to
PoE networks without routing to outside
plants.

2. For PoE input connections, use only UL
listed I.T.E. with PoE output.

L
I
N

K

RE

CEIVE

N

PoE Switch

POW

ER

C

OLL

I
S
ION

1

PARTITIO

2

3

4

5

When using a non-PoE switch

Use a PoE power injector (optional) to connect between the Network Camera and a
non-PoE switch.

English

EN - 7

PoE Power Injector

(optional)

L
I

N

POW

K

ER

C
O

LL

I
S

RE

ION

CEIVE

1

PARTITIO

2

3

N

4

5

Non-PoE Switch

5

Assigning an IP Address

1. Install “Installation Wizard 2” from the Software Utility directory on the software CD.

2. The program will conduct an analysis of your network environment. After your network is
analyzed, please click on the “Next” button to continue the program.

Installation

Wizard 2

3. The program will search for VIVOTEK Video Receivers, Video Servers, and Network
Cameras on the same LAN.

4. After a brief search, the main installer window will pop up. Double-click on the MAC
address that matches the one printed on the camera label or the S/N number on the
package box label to open a browser management session with the Network Camera.

0002D107258A

00-02-D1-07-25-8A 192.168.5.151 FD8135H

0002D107258A

EN - 8

6

Ready to Use

1. A browser session with the Network Camera should prompt as shown below.

2. You should be able to see live video from your camera. You may also install the 32­channel recording software from the software CD in a deployment consisting of multiple
cameras. For its installation details, please refer to its related documents.

English

For further setup, please refer to the user's manual on the software CD.

EN - 9

Adjusting the Lens

7

Based on the live image retrieved from the camera, adjust the camera lens to the desired
view angle:

1. Turn the lens module left and right.

2. Loosen the tilt adjustment screws on both sides of the camera and then turn the lens

module up and down. Upon completion, tighten the screws.

3. Turn the lens to adjust the image orientation.

2

3

1

Pan 350°

3-axis Mechanism Design

Tilt 65°

Rotate 350°

The sophisticated 3-axis mechanism design offers very exible, easy hardware installation

for either ceiling or wall mount.

To adjust the zoom factor and focus range

1. Loosen the zoom controller and then adjust zoom factor by moving the controller left
and right. Upon completion, tighten the zoom controller screw.

2. Loosen the focus controller and then adjust focus range by moving the controller left
and right. Upon completion, tighten the focus controller screw.

W

T

N

8

DO NOT over-tighten the controller
bars. Doing so will damage the
camera lens module.

EN - 10

NOTE:

1. The Focus Assist button takes effect when using a hand-held monitor or camera tester
with a BNC connector. Press the button and use the focus and zoom adjustment
pullers to tune the image until the "BEST FOCUS" message is shown.

Focus Assist
Button

LCD Monitor/
Camera tester

AV Out

2. When mounting the camera, you can use the key hole slot at the bottom. The key hole
slot helps facilitate installation and a safe mounting.
2-1. First fasten a pioneer screw to the wall/ceiling. Mount the camera to the screw.
2-2. Use a pencil to mark the locations of the 3 permanent mounting holes.
2-3. When cabling and the initial adjustment is done, mount the camera by fastening

screws to the 3 mounting holes.

Key Hole Slot

English

Mounting Holes

Pioneer Screw

EN - 11

Completion

8

1. Align the notches on the inner side of the black cover with the rivets on the sides of the

lens, and then x the black cover.

2. If you choose to feed the cable through the ceiling/wall, arrange the cables neatly
through the cable hole A (not shown in the drawing). If you choose to feed the cable
from the side, remove plate B.

3. Attach the dome cover to the camera as the direction shown below. Tighten two screws
from the sides of the dome cover.

4. Finally, make sure all parts of the camera are securely installed.

1

Black Cover

2

Dome Cover

A

3

B

Be aware of the
cable route!

EN - 12

P/N:625016800G Rev. 1.0

All specications are subject to change without notice.

c

Copyright 2012 VIVOTEK INC. All rights reserved.

VIVOTEK INC.

6F, No.192, Lien-Cheng Rd., Chung-Ho, New Taipei City, 235, Taiwan, R.O.C.

|T: [phone]| F: [phone]| E: [e-mail]

VIVOTEK USA, INC.

2050 Ringwood Avenue, San Jose, CA 95131

|T: 408-773-8686| F: 408-773-8298|E : [e-mail]