Vandal-proof
.
Tamper Detection
.
PoE
Quick Installation Guide
English
ᖅϛ Рҏᇭ
ᙏϛ
Français
Español Português
Deutsch
Italiano
Türkçe
Polski
Русский
Česky Svenska
FD7130
This guide describes the basic functions of FD7130
All detailed information is described in the user's manual.
IP Surveillance
Warning Before Installation
English
Power off the Network Camera as
soon as smoke or unusual odors are
detected.
Contact your distributor in the event of
occurrence.
Do not place the Network Camera
around heat sources, such as a
television or oven.
Keep the Network Camera away from
direct sunlight.
Keep the Network Camera
away from water. If the Network
Camera becomes wet, power off
immediately.
Contact your distributor in the event of
occurrence.
Refer to your user’s manual for
the operating temperature.
Do not place the Network Camera
in high humidity environments.
EN - 1
Do not place the Network Camera
on unsteady surfaces.
Do not touch the Network Camera
during a lightning storm.
Do not disassemble the Network
Camera.
Do not insert sharp or tiny objects
into the Network Camera.
EN - 2
Do not drop the Network Camera.
1
Package Contents
English
FD7130 with an RJ45 or M12 Cable
RJ45
Software CD
Quick Installation Guide /
Warranty Card
Liquid Tight Connectors for
RJ45 or M12 Cable
RJ45 M12
Alignment Sticker
Ground Wire / Screws
Screwdriver
Silica Gel
EN - 3
2
Physical Description
Inner View
Lens
Screw Holes
Temperature Alarm
The alarm will be triggered
once the temparature inside the
Network Camera reaches 60°C.
Outer View
Waterproof Level: IP66
Reset Button
EN - 4
MicroSD/SDHC Card Slot
Status LED
Record the MAC address
before installing the camera.
Network Camera
Model No: FD7130
MAC:0002D107258A
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions:
(1)This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
Pat. 6,930,709
RoHS
Made in Taiwan
3
Cabling Assembly
RJ45 Cable Connector
RJ45 Cable Dimension (unit: mm)
Assembling Steps
1
Prepare an Ethernet cable
and strip part of the sheath.
Recommended cable gauge: 24AWG
(0.51 mm)
Insert the stripped Ethernet
4
cable through the sealing
nut and the housing.
(A)
2
Insert the housing into the
screw nut.
(C)
5
Clamp the cable with
an RJ45 plug.
Components of the Waterproof
Connector
Sealing Nut (A)
Seal (B)
Screw Nut (C)
3
Insert the seal into the housing.
(D)
(B)
6
Push the RJ45 plug into the
housing, then secure the
sealing nut tightly.
English
Housing (D)
Gasket (E)
7
Attach the gasket to the front
of the housing.
(E)
Connect the Ethernet cable to the RJ45 cable
8
and secure the connectors tightly.
EN - 5
M12 Cable Connector
M12 Cable Dimension (unit: mm)
Assembling Steps
1
Prepare an Ethernet cable
and strip part of the sheath.
Insert the stripped Ethernet
4 5
cable through the sealing nut
and the clamp ring.
(A)
Components of the Waterproof
Connector
2
Insert the seal into the clamp
ring.
(B)
Ø4.5mm~Ø6.5mm
Follow the pin definition in the below table
to solder the stripped Ethernet cable to the
plastic nut.
(C)
(E)
Sealing Nut (A)
Seal (B)
Clamp Ring (C)
Gasket (D)
Plastic Nut (E)
3
Insert the gasket into the clamp
ring.
(D)
6 7
Secure the sealing nut to the
clamp ring tightly.
Ethernet Cable /
M12 Cable
1 Orange/White
2 Orange
3 Green/White
4 Blue
5 Blue/White
6 Brown/White
7 Brown
8
Wire Color
Green
Follow the pin definition in the below table
to connect the Ethernet cable to the M12
cable and secure them tightly.
Ethernet Cable
EN - 6
M12 Cable
4
Hardware Installation
First, use the supplied screwdriver to detach the dome cover from the camera base. Insert your
MicroSD/SDHC Card if necessary.
Tamper-proof Screw
Dome Cover
Rubber Stopper
Camera Base
Then, follow the steps below to install the camera to either the ceiling or the wall:
1. Attach the supplied alignment sticker to the ceiling/wall.
2. Using the 3 screw circles on the sticker, drill 3 pilot holes into the ceiling/wall. Then hammer the
plastic anchors into the holes.
3. This Network Camera can be mounted with the cable routed through the camera base or from
the side of the dome cover. If you want to feed the cable through the ceiling/wall, please also
cut or drill a hole (A) for the cable. If the cable goes through the side of the dome cover, please
remove the rubber stopper (B).
4. Through the 3 holes on the camera base, insert the screws to corresponding holes and secure
the camera base with a screwdriver.
Ceiling Mount
English
1
2
A
B
A
3
4
EN - 7
Wall Mount
1
2
B
A
3
Please secure the screws tightly to
avoid moisture.
4
Installing the Ground Wire
As shown in the following figure, please secure one side of the supplied ground wire to the screw
hole, then route the other side of the ground wire to the ground.
EN - 8
Network Deployment
5
Power over Ethernet (PoE)
When using a PoE-enabled switch
This Network Camera is PoE-compliant, allowing transmission of power and data via a single
Ethernet cable. Follow the below illustration to connect the camera to a PoE-enabled switch via
Ethernet cable.
PoE Switch
English
POWER
LINK
COLLISION
RECEIVE
1
2
PARTITION
3
4
5
When using a non-PoE switch
Use a PoE power injector (optional) to connect between the Network Camera and a non-PoE
switch.
PoE Power Injector
(optional)
LINK
POWER
COLLISIO
RECEIVE
N
1
2
PARTITION
3
4
5
Non-PoE Switch
EN - 9
6
Assigning an IP Address
1. Install “Installation Wizard 2” from the Software Utility directory on the software CD.
2. The program will conduct an analysis of your network environment. After your network is analyzed, please click on the “Next” button to continue the program.
Installation
Wizard 2
3. The program will search for VIVOTEK Video Receivers, Video Servers, and Network Cameras
on the same LAN.
4. After searching, the main installer window will pop up. Click on the MAC that matches the one
labeled on the bottom of your device to connect to the Network Camera via Internet Explorer.
Network Camera
Model No: FD7130
MAC:0002D107258A
RoHS
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions:
(1)This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
Pat. 6,930,709
Made in Taiwan
00-02-D1-07-25-8A 192.168.5.151 FD7130
0002D107258A
EN - 10
7
Ready to Use
1. Access the Network Camera on the LAN.
2. Retrieve live video through a web browser or recording software.
For further setup, please refer to the user's manual on the software CD.
Adjusting the Lens
8
To adjust the viewing angle
Adjust the lens to a desired viewing angle as the diagram shown below.
English
10°
10°
DO NOT over rotate the lens. Doing
so will damage the camera lens
module.
EN - 11
90°
Fine-tune the Camera Focus
The focus of this network camera is set from 1.0m to infinity by factory default. If you want to focus
on objects closer than 1.0m or the lens has lost focus, please fine tune it in the following way.
1. Loosen the lens lock screw.
2. Manually rotate the lens to fine-tune the focus
until the live image is clear.
3. Tighten the lens lock screw.
Tighten the lens lock screw.
Completion
9
Tear down the aluminum foil vacuum bag and take out the silica gel. Attach the supplied silica gel to
the inner side of the Network Camera. (Please replace the silica gel with a new one if you open the
back cover after installation.)
Attach the dome cover to camera. Secure the dome screws with the supplied screwdriver. Finally,
make sure all parts of the camera are securely installed.
Please secure the screws tightly to
prevent the cabling against moisture.
EN - 12
Copyright 2009 VIVOTEK INC. All right reserved.
P/N: 625008801G Ver.1.1
Loading...