Page 1
VIVOTEK Fixed Dome Series
Mounting kit
Using
AM-52E Mounting Adapter,
AM-118 Pendant Head (indoor),
AM-114 Pendant Head (outdoor)
AM-116 and AM-117 Pendant Pipes,
AM-522 NPT adaptor
AM-218 Wall Mount,
AM-312 Pole Mount,
AM-412 Corner Mount
Installation Guide
Corresponding part number:
AM-52E: 100217700G
AM-116: 900014301G
AM-117: 900014401G
AM-118: 900014601G
AM-312: 900034802G
AM-412: 900034902G
AM-522: 900020202G
AM-218: 100146100G
AM-114: 900004101G
Rev. 1.0
IP Surveillance
Page 2
Revison History:
AM-52E Mounting Adapter Package Contents
Applications
Rev. 1.0: Initial release.
M4x8
M3x8
M6x6
M3 hex
AM-52E
AM-118
AM-116
AM-117
AM-118
AM-522
NPT adaptor
NPT pipe
For other applications, please refer to page
13.
AM-52E
2
Page 3
Compatible VIVOTEK Cameras
1
English
Combination
Direct installation:
AM-118/114 + AM-117/116
+ AM-52E
Compatible Models Screw
A: FD9360-H, FD9380-H M4x8
B: IT9388-HT
C: IT9360-H, IT9380-H
D: IT9389-H, IT9389-HT M3x8
WARNING:
1. Select a suitable location where the camera is free from accidental damage, tampering,
or harsh environmental conditions.
2. Locate a place for the installation where the camera can not be intentionally or
unintentionally interfered.
3. Select a solid and at mounting surface that can support the combined weight of the
camera and associated hardware. Vibration and temperature range should also be taken
into consideration.
3
Page 4
Compatible Accessories
2
Compatible Accessories (1): AM-312 Pole
Mount Bracket
Compatible Accessories (4-3): AM-218
Wall-mount Bracket
Compatible Accessories (5-2): AM-114
Pendant Head
Compatible Accessories (2): AM-412
Corner Mount Bracket
Compatible Accessories (5-1): AM-118
Pendant Head
Compatible Accessories: AM-522
Pendant NPT Adaptor
4
Page 5
Compatible Accessories (5-2): AM-116 and AM-117 Pendant Pipe
552.2mm
Shown below are the mounting dimensions using a 40cm pendant pipe (AM-117).
AM-118
140 mm
AM-117
438.2 mm
English
FD9380
24.5mm
89.5 mm
117.1 mm
5
Page 6
Direct Installation
3
3-1. Using the Pendant Pipe
2
1
1. Determine a hard surface ceiling
location, and use the included alignment
sticker for marking three mounting holes
as where holes will be drilled to secure
the pendant head.
2. Hammer in the plastic anchors.
AM-118
3. Secure pandant head using the included
screws.
4. Install the pendant pipe.
5. Tighten the retention screw using the hex
wrench.
6. Install the AM-52E.
7. Tighten the retention screw using the
included hex wrench.
AM-116/
AM-117
3
5
4
7
AM-52E
6
6
Page 7
8. Pull the cables through the pendant pipe, and install the waterproof cable gland. Install
the camera using the corresponding mounting holes.
5.5 ~ 6.4mm
Some cameras come with a side-routing cutout. Use the included side lid to seal the
cutout.
English
7
Page 8
3-2. Using the 3/4" NPT Pipe
AM-118
AM-522
3/4" Female adapter
3/4" pendent pipe
AM-52E
115 mm
1. Determine a hard surface ceiling location, and use the included alignment sticker for
marking three mounting holes as where holes will be drilled to secure the pendant head.
2. Hammer in the plastic anchors.
2
1
8
Page 9
3. Secure the pandant head using the included screws.
4. Install the AM-522 adaptor and the NPT female-female coupler (user-supplied)
5. Tighten the hex socket screw using the hex wrench.
6. Install the 3/4" NPT pipe of a preferred length.
7. Install the AM-52E.
AM-118
5
3
AM-522
NPT femalefemale coupler
4
English
3/4” NPT pipe
AM-52E
6
7
9
Page 10
8. Pull the cables through the NPT pipe and the camera base. Align the camera's
mounting holes with the associated holes on the bracket. It is recommended to install
the waterproof cable gland.
10
Page 11
Using Other Accessories
4
4-1. Wall-mount Installation - AM-218
Below is a general, sample procedure using a gooseneck bracket:
1. Route the Ethernet and/or other cables through the wall and the bracket.
2. Locate the position where you want to install the wall-mount bracket and camera. Drill
holes on the wall for securing the bracket and for routing the cables.
Secure the bracket by hammering anchors into the wall and then fasten screws through
it. Drill 10mm holes in diameter and 60mm deep.
3. Attach the mounting adapter to the bracket by rotating it clockwise until it is tightly
fastened.
WARNING:
When you hammer the threaded anchors into wall, keep the nuts and washers on them in
case the top of threaded poles can be deformed during the process.
English
2
3
Mounting adapter
55
Dome camera
4. Use a hex wrench to secure the mounting adaptor to the wall-mount bracket.
5. When cabling is done, proceed with initial setup such as enabling network access, focus
tuning, or zooming. When done, secure the outer dome cover.
4
1
Cables
11
Page 12
4-2. Corner Mount Installation
Dimension drawing:
215,71
M8X20mm
SUS 302
175
4- 6
4- 7
3- 4,5
45
56,29
86
102
315,25
144,17
48,75
86
170
102
12
Page 13
English
M4X15
X4
X4
M6X20
5mm X1
M5X20
4mm X1
X4
Below is a general, sample procedure using a Corner mount bracket:
1. Combine the two metal pieces together using the M8 hex nuts and washers.
M8
X2
13
Page 14
2. Align the assembled brackets with the desired position. Align screw holes on the
brackets against the wall. Drill holes on the wall for securing the bracket and for routing
the cables. Hammer the anchors into the wall. Note that these screws and wall anchors
are user-supplied.
x8
The 4 screw holes marked below are used for mounting the bracket (using the M4 screws).
14
Page 15
3. Install the AM-218 bracket to the top of AM-312. Install the AM-52E to the bracket and
tighten the retention hex screw.
AM-218
AM-52E
Dome camera
English
15
Page 16
4-3. Pole Mount Installation
The pole mount bracket is designed to accommodate a pole in a diameter ranging from 90
~ 152mm (3.5 ~ 6 inches)
84,9
55°
4- 6
173,79
45
56,29
86
99
3- 4,5
4- 7
68,75
55°
70,05
2
4-OB 25.5X5.5mm
48,75
86
170
102
16
Page 17
M4X15
M6X20
X4
X1
5mm
M5X20
4mm
X4
X1
X4
Below is a general, sample procedure using a Pole mount bracket:
Use the mounting holes indicated below for the conduit box.
Stainless steeel strap
English
X2
17
Page 18
1. Secure the AM-719 conduit box to bracket using the M4 screws, washers, and hex
heads. A hex crescent wrench is required. You can do this before you install the polemount bracket.
M4
2. Pass the stainless steel straps through the bracket and around the pole.
18
Page 19
4. Tighten the straps using a pincer plier and a at blade screwdriver.
Installation Torque:
35 lb-in(40kg-cm)
The corresponding mounting holes and cameras are shown below:
Combination
Direct installation:
AM-52E
Compatible Models Screw
A: FD9360-H, FD9380-H M4x8L
B: IT9388-HT
C: IT9360-H, IT9380-H
English
6. Install the AM-52E to the bracket and install your camera to the AM-52E adapter
bracket.
5.5 ~ 6.4mm
19
Page 20
This page is intentionally left blank.
20
Loading...