Page 1
VIVOTEK Fixed Dome Series
Mounting Cap
AM-52B Mounting Cap,
AM-522 Mounting Adapter,
AM-116 Mounting Pipe,
AM-117 Mounting Pipe
AM-118 Pendant Head
Installation Guide
Corresponding part number:
AM-52B: 100193800G
AM-116: 900014301G
AM-117: 900014401G
AM-118: 900014600G
AM-522: 900020201G
Document part no.: 625047800G
Rev. 1.0
IP Surveillance
Page 2
Revison History:
AM-52B Mounting Adapter Package Contents
Applications
Rev. 1.0: Initial release.
AM-52B
AM-118
AM-116
AM-117
AM-522
AM-118
AM-522
NPT female
adaptor
NPT pipe
AM-52B
2
Page 3
Compatible VIVOTEK Cameras
1
English
Standard pipe installation:
AM-118+AM-117 / 116 + AM-522 +AM52B
NPT pipe:
AM-118 + AM-522 + NPT pipe + AM-52B
WARNING:
1. Select a suitable location where the camera is free from accidental damage, tampering,
or harsh environmental conditions.
2. Locate a place for the installation where the camera can not be intentionally or
unintentionally interfered.
3. Select a solid and at mounting surface that can support the combined weight of the
camera and associated hardware. Vibration and temperature range should also be taken
into consideration.
Compatible Accessories
2
Compatible Accessories: AM-118 Pendant Head
Compatible Accessories: AM-522 Pendant NPT Adaptor
FD8166A series, FE9180-H
FD8166A series, FE9180-H
Compatible Accessories: AM-116 and AM-117 Pendant Pipe
NOTE: The NPT pipes and adapters are user-supplied.
3
Page 4
Direct Installation
3
3-1. Using the Pendant Pipe
2
1
1. Determine a hard surface ceiling
location, and use the included alignment
sticker for marking three mounting holes
as where holes will be drilled to secure
the pendant head.
2. Hammer in the plastic anchors.
3. Secure pendant head using the included
screws.
4. Install the pendant pipe.
5. Tighten the retention screw using the hex
wrench.
6. Install the AM-522.
7. Install the AM-52B.
8. Tighten the retention screw using the
included hex wrench.
AM-118
AM-522
AM-52B
4
AM-116/
AM-117
3
5
4
8
6
Page 5
8. Install the camera to the mounting cap. Install the mounting bracket using 4 screws
for the sheye camera. Follow the procedure on the camera's QIG for the rest of the
installation steps. Note that the FD8166A requires only 2 screws.
English
5
Page 6
3-2. Using the 3/4" NPT Pipe
AM-118
AM-522
3/4" Female adapter
3/4" pendant pipe
155 mm
1. Determine a hard surface ceiling location, and use the included alignment sticker for
marking three mounting holes as where holes will be drilled to secure the pendant head.
2. Hammer in the plastic anchors.
AM-52B
2
1
6
Page 7
3. Secure the pendant head using the included screws.
4. Install the AM-522 adaptor and the NPT female-female coupler (user-supplied)
5. Tighten the retention screw using the hex wrench.
6. Install the 3/4" NPT pipe of a preferred length.
7. Install the AM-52B and tighten the retention screw.
AM-118
5
3
AM-522
NPT femalefemale coupler
4
English
3/4” NPT pipe
AM-52B
6
7
7
Page 8
Note the FD8166A has a xed shooting direction. You can turn the mounting cap towards
a desired direction and then fasten the retention screw.
8
Loading...