Vivotek AM-312 Installation Guide
VIVOTEK Mounting Accessories
Mechanical Drawings
II
AM-312 Pole mount
Installation Guide
Revision History:
Rev. 1.0: Initial release
Corresponding ordering part numbers:
AM-312: 900034800G, AM-714: 100134800G
AM-715: 100134700G AM-218: 100146100G
Compatible VIVOTEK Cameras
I
Compatible brackets Supported Cameras
AM-714 IB836B-HF3/6B-EHF3, IB836B-HT/6B-EHT, IB9371-HT/71-EHT, IB8382-F3/82-EF3,
AM-715 IB8367/67-R, IB8367-T/67-RT, IB8338-H/38-HR
AM-218 (via AM-714) Please refer to AM-218 documents.
Directly attached Supported Cameras
* IB836B-HF3/6B-EHF3, IB836B-HT/6B-EHT, IB9371-HT/71-EHT, IB8382-F3/82-EF3,
* The directly-attached conguration is less recommended for the lack of waterproof and cabling
protection. If directly attached, you should properly wrap the rear-end cables and connectors with
waterproof protection such as putties.
Package Contents
Items 1. Pole mount bracket, 2. Stainless strap x2, 3. M6X20mm screws x4. 4. M5X20mm
IB8382-T/82-ET, IB9381-HT/81-EHT, IB9371-HRT, IB9381-HRT
IB8382-T/82-ET, IB9381-HT/81-EHT, IB9371-HRT, IB9381-HRT
screws x4, 5. Hex L wrench 5mm x1, 6. Hex L wrench 4mm x1.
AM-312 Pole mount bracket
84,9
55°
6
45
7
55°
102
86
173,79
AM-312 Applications
AM-218
70,05
102 2
170
AM-714
AM-520 / AM-525, etc.
AM-312
The pole mount bracket is designed to
accommodate a pole in a diameter ranging from 90
~ 152mm (3.5 ~ 6 inches)
AM-714
AM-312
- or -
AM-715
Bullet camera
X4
X1
M5X20
4mm
Installation
III
M6X20
5mm
Below is a general, sample procedure using a Pole mount bracket:
1. Pass the stainless steel straps through the bracket and around the pole.
2. Tighten the straps using a pincer plier and a at blade screwdriver.
X4
X1
Stainless steeel strap
Installation Torque:
35 lb-in(40kg-cm)
Dome camera
X2
• Make sure you have purchased the adequate accessories to be combined for your installation.
• Please do not install an indoor camera in an outdoor environment! Doing so will void our
warranty. This is determined by whether the camera housing is weather-proof.
• Direct sunlight can tremendously increase the temperature within the device.
4. Secure the AM-714 conduit box to bracket using the M5 screws, washers, and hex heads. A hex crescent
wrench is required.
M5
3. The 4 screw holes in the center are used for directly mounting the IB series bullet cameras.
The 4 screw holes at the edges are used for mounting the AM-714 conduit box.
For M6 socket screws
- for IB series bullet cameras
directly attached
For M5 socket screws
- for AM-714 conduit box
If you are installing a bullet camera directly to the bracket, use the M6 screws in the center. A hex crescent
wrench is required.
M5
5. For the rest of the installation procedure, refer to the documentation that came with the AM-714, AM-715, AM218, and the other accessories.
The 3/4" cable glands and conduts for protecting cables are user-supplied.
AM-312_ig_A3_v10_20160320.indd 1 2016/4/7 下午 01:43:09
Loading...