AI-103
IR Illuminator
Installation Guide
Rev. 1.1
IP Surveillance
Revision History:
Rev. 1.0: Initial release
Rev. 1.1: Changed effective IR range.
Specications
I
Model Name AI-103
IR LED quantity 6 pcs
IR light range 20 meters
IR wavelength 850nm
IR bean angle 60°
IR light control. CTRL (+/-) by camera
Input voltage AC 90~240V
Operating current (constant) 500mA
Power consumption 6Watt
Operating temperature -10°C ~ +40°C
Storage temperature -20°C ~ +60°C
Dimensions OD 60 x L160mm
Weight 750g
2
Mounting & Cabling
II
Preparing for installation:
1. Remove the IR illuminator from its package.
2. You should purchase power cords with
adequate length.
3. A T20 hex wrench.
Assemble the IR illuminator with the
Support Bracket:
Use the included hex wrench to slightly loosen the ball swivel to adjust the shooting
angle.
IR illuminator
English
Bearing housing
Ball swivel
Camera stand
3
Install the IR illuminator next to your network camera, e.g., IP8352. Orient its shooting
angle by adjusting the ball swivel screw. Secure the illuminator by fastening screws
through the holes on the base of the equipment stand.
If you drilled a hole on the wall, you can pass power and control lines through the hollow of
the equipment stand and then through the hole
Wiring
III
There are 5 wires with the illuminator: 3 for power connections and another 2 as control
lines to the Digital outputs from a network camera. Refer to the diagram below for details.
Power cords
Connector Block
To Camera
Black: AC input
Yellow: GND
White: AC input
Red
Blue
4
AC Power Connection
Digital output
Power lines are connected to a connection block. Use them to connect the power cords
you separately purchased.
Control Line Connection
Disassemble the waterproof connector through which you will route your control lines to
the IR illuminator.
Rubber ring (A)
Screw nut (B)
Rubber seal (C)
Seal plugs (D)
Housing (E)
Sealing nut (F)
IP8352 GPIO Pinouts
Ground
English
87654321 109
Red
Blue
Shown above is the network camera's General Purpose IO terminal block. Connect the IR
illuminator's red and blue lines to pin2 and pin4 on the terminal block.
5
1. Open the rear cover using a athead screwdriver (taking the IP8352 as an example).
2. Replace the seal plug on the rear cover with parts A & B from the waterproof connector.
3. Pass digital IO lines through F > E > C > A+B. Insert D into unused holes on C.
4. Connect DO lines to the GPIO terminal block (shown above). Secure the sealing nut (F)
by tightening to the rear cover.
5. Close the rear cover.
6. Pass IO lines through the mounting bracket.
1
2
(A)+(B)
(C)
(E)
(F)
3
(D)
(F)
4
5
(G)
6
6
IR Conguration
IV
To congure the IR-related settings in camera rmware:
1. Open a browser management session according to your QIG (Quick Installation Guide).
2. On the main page, enter Conguration > Advanced mode > Media > Image (General
settings) > click on a tab at the lower screen to open Day/Night settings.
3. Select the checkbox in front of "Turn on external IR illuminator in night mode." Click
Save to preserve your setting.
Once the conguration is done, the network camera will automatically turn on the
illuminator when its light sensor detects low-light conditions, e.g., when the night comes.
English
NOTE:
previously congured in the Event conguration will be erased.
Since only one pair of digital output lines are available, once the IR illuminator is enabled,
the other Digital output options will be disabled.
If the external IR illuminator setting is enabled, all DO-related settings you
7
8
IP Surveillance
Loading...