Vivotek AE-238, AE-239, AE-243, AE-244, AE-23A Installation Manual
...
IP Surveillance
Installation Guide
AE Series
Rev. 1.0
Outdoor Housing
Ordering part no.:
AE-238 900041100G
AE-239 900041200G
AE-243 900041900G
AE-244 900042400G
AE-23A 900042300G
AE-23B 900042200G
AE-23C 900041700G
AE-23D 900041800G
AE-23E 900041600G
AE-23F 900042100G
2
Specications
I
Model Number AE-238, AE-243 AE-23A, AE-23B, AE-
23C, AE-23D
AE-239, AE-244 AE-23E, AE-23F
Power Input 24V AC/ DC 24V AC/ DC PoE: 50~57V DC PoE: 30/60/95W, 50~57V
DC
Max. Output power
budget
30W 80W, 100W (-AIW) 30W 25W - 30W PoE PSE
48W - 60W PoE PSE
72W - 95W PoE PSE
Power Consumption Window heater: 10W;
Blower: 2W; Camera: 6 ~
8W
Window heater: 10W;
Blower: 2W; Camera: 6
~ 8W; Cold start heater:
30W
Window heater: 10W;
Blower: 2W; Camera: 6 ~
8W; IR: 6W
Window heater: 10W;
Blower: 2W; Camera: 6 ~
8W; Wiper: 6W
Environmental
Operation Temp.
-20°C ~ +65°C (-4°F ~
+149°F)
-20°C ~ +65°C
-20°C ~ +50°C (w/ IR)
-24°C ~ +50°C (Cold start)
-20°C ~ +65°C
-20°C ~ +50°C (w/ IR)
-20°C ~ +65°C
-20°C ~ +50°C (w/ IR)
Window heater ON/OFF ≤ 30°C (86°F) ON; ≥ 35°C
(95°F) OFF
≤ 30°C (86°F) ON; ≥ 35°C
(95°F) OFF
≤ 30°C (86°F) ON; ≥ 35°C
(95°F) OFF
≤ 30°C (86°F) ON; ≥ 35°C
(95°F) OFF
Blower Control ≥40°C (104°F) ON; ≤ 35°C
(95°F) OFF
≥40°C (104°F) ON; ≤ 35°C
(95°F) OFF
≥40°C (104°F) ON; ≤ 35°C
(95°F) OFF
≥40°C (104°F) ON; ≤ 35°C
(95°F) OFF
Protection Level IP67, IK10 IP67, IK10 (IP66 w/ wiper) IP67, IK10 IP67, IK10 (IP66 w/ wiper)
Construction Die-cast Aluminum Alloy Die-cast Aluminum Alloy Die-cast Aluminum Alloy Die-cast Aluminum Alloy
Coating White epoxy powder
coating
White epoxy powder
coating
White epoxy powder
coating
White epoxy powder
coating
Dimensions 415 (L) x 170 (W) x 125 (H) mm502.8 (L) x 170 (W) x
135.5 (H) mm
415 (L) x 170 (W) x 125 (H)
mm - IR not included
502.8 (L) x 170 (W) x 135.5
(H) mm - IR not included
Net Weight 2,2kg (4.84 lb) 2,7kg (5.95 lb), 2,8kg (6.18
lb - wiper model)
2,2kg (4.85 lb) 2,7kg (5.95 lb), 2,8kg (6.18
lb - wiper model)
UNPACKING:
Unpack carefully. Electronic components can be damaged if improperly handled or
dropped. If an item appears damaged in shipment, place it properly in its carton and
notify the shipper.
IMPORTANT!:
1. Read and follow Instructions: All operating and user instructions should be read and
followed before the unit is to be operated.
2. Electrical Connections: Only a qualied electrician is allowed to make electrical
connections.
If you plan to install this camera enclosure into a tropical, sea coastal, or an environment
where salt water or corrosive industrial waste water/moist are present, please seal each
stainless steel screws and ttings with a silicon grease compounds. This will help prevent
electrolysis to occur and extend the life span of the camera and housing.
IMPORTANT:
1. Disconnect devices: A readily accessible disconnect device in the building installation wiring
should be incorporated.
2. Electrical Connection: Only a qualied electrician is allowed to make electrical connections.
3
English
Mounting Conguration & Dimensions
II
Swivel Positions and Directions
415 mm
125 mm
170 mm
400 mm
255 mm
USABLE AREA
105 mm
77.4 mm
USABLE
AREA
105 mm
502.8 mm
135.5 mm
158.5 mm
170 mm
400 mm
77.4 mm
USABLE
AREA
255 mm
USABLE AREA
AE-238, AE-239
AE-23A, 23B, 23C, 23D, 23E, 23F
415 mm
206.9 mm
170 mm
400 mm
135 mm
88.05 mm
87.01 mm
AE-243, AE-244
4
Component Description
III
Camera Mounting Platform
M16 1/2" Waterproof cable glands
AC/DC or PoE Power
distribution board
Ventilation fan
Window frame
heater coil
217.4 mm
502.8 mm
417 mm
135 mm
88.05 mm
87.01 mm
95˚
R96.5
95˚
95˚
R96.45
Dimensions with the IR unit and wiper
VAIR module
5
English
Installation
V
Installation Suggestions
IV
1.
Prepare power wires, a ground wire, and a CAT5e Ethernet cable. Pass them through
the M16 waterproof connectors and its waterproof components.
• When install a housing with an IR illuminator:
Please avoid eye exposure or apply appropriate protection, such as wearing a pair of Infrared
protection glasses, when working with the product. Always use camera live view to oberve IR
lighting effects.
WARNING:
Ethernet cable Ø4 ~ 6.5mm
Power wires & DI/DO wires,
a combo cable from IR illuminator
(if applied)
Note that some cables are connected when shipped. You do not need to connect heater,
blower, and the front IR powere wires.
6
o
O
g
B
b
G
br
BR
1
2
3
4
5
6
7
8
o: white/orange stripe
O: orange solid
g: white/green stripe
B: blue solid
b: white/blue stripe
G: green solid
br: white/brown stripe
BR: brown solid
You may need to remove the RJ45 connector, and use a crimping tool to connect the
Ethernet wires to an RJ45 connector inside the enclosure. Use an Ethernet cable of the
width of 5 ~ 6.5mm.
2.
When done, tighten up and install the waterproof connectors.
3.
Assemble the camera components, e.g., the CS ring and lens module. Secure the
mounting plate to the bottom of the camera (the label side) using the included screw.
7
English
Lens flush
w/ edge of
enclosure
4.
Adjust the camera's position so that the lens module can ush align with the tempered
glass. Secure the camera using the screws and washers to the bottom of the housing.
5.
Connect 24V power source to the power input terminal. Connect power wires from the
DC 12V output to the camera. You may also connect the 24V power to drive an external
IRs.
Below is the distribution board drawing power from 24V AC/DC.
Heater
Blower
IR angle selector
I/O terminal block
Camera heater
24V AC/DC IN
12V DC OUT
24V AC/DC OUT
Connectors to the front IR
Power LED
AE-23A, AE-23B, AE-23C, AE-23D
8
Below is the pinouts for the DI/DO terminal block:
Facing the rear side of the housing, from left to right:
DO2 Tank water pump control, connects to IP camera's DO for manually triggering
washer.
DI2 Wiper control.
RS485+ RS485+, RS485 can be used to control IR illuminator beam angles, etc.
RS485- RS485DO+ +5V VCC
DI- GND
DO1 IR LED status
DI1 IR control, synchronizes day/night mode switching for IP camera. It is related to IR
cut lter.
AE-238, AE-243
DC 12V OUT - to camera
AC 24V OUT - to external IR
AC 24V IN
Ground
for IR LED
AC 24V OUT - to camera
AC 24V IN
AE-238
AE-243
Loading...