Vivitek DU6771 User Manual
Remote Communicaton
Manual
DU6771
DU6771 series DLP Projector Remote Communication Manual
Table of Contents
The Serial Interface RS-232 Command ........................................................................................ 2
Communication parameter ......................................................................................................................................... 2
Operation commands ................................................................................................................................................. 2
Operation command syntax ................................................................................................................................ 2
List of operation commands................................................................................................................................ 3
Simulated IR remote controller commands .............................................................................................................. 13
List of simulated IR remote controller commands.................................................................................................... 13
Control the Projector Through a Network.................................................................................. 14
Cable connection ..................................................................................................................................................... 14
Set up the projector for networking .......................................................................................................................... 15
Control the projector through a network .................................................................................................................. 16
Control the projector through a web browser ................................................................................................... 16
Control projector with TCP/IP communication protocol .................................................................................... 19
About Vivitek Support ................................................................................................................. 20
1
RC67711216EN00
DU6771 series DLP Projector Remote Communication Manual
Item
Parameter:
the cable length.
op
:
A constant indicating this is an operation command.
[SP]
:
Indicate one blank space.
[CR]
:
Indicate the command ending carriage return pair "CR" and "ASCII hex 0D".
Setting value
:
Settings of operation command
Types of setup strings
Characters of settings
Description
Query current setup
?
Question mark "?" indicates querying current setup
Setup
= <settings>
Syntax: Symbol "=" suffixed with setup values
Increase the value
+
Some settings are changed in steps. Symbol "+"
indicates changing one step up
Decrease the value
-
Some settings are changed in steps. Symbol "-"
indicates changing one step down
Execute operation command
None
Certain operation commands execute after input
without further setting or regulators.
Control items
Input command
Projector return message
Query current brightness
op bright ? [CR]
OP BRIGHT = 101
Set brightness
op bright = 127 [CR]
OP BRIGHT = 127
Set input signal source to HDMI
op input.sel = 0 [CR]
OP INPUT.SEL = 0
Reset projection lens to
center position
lens.center
The Serial Interface RS-2 3 2 Comm and
This projector supports to control by RS-232 command, there exists two types of RS-232 serial commands:
Operation command: The commands are listed by the OSD menus structure as PICTURE,SI GNAL, SETUP,
INSTALLATION, SERVICE and SERVICE.
Simulated IR remote controller commands: Controls projector via RS-232 command, the commands simulate IR
remote controller and its control keys.
Communication parameter
You can use the serial control command to input commands for projector control or retrieve its operational data
through Windows client terminal software, e.g. Hyper Terminal, with ASCII characters. You need to set up the following
communication parameters in advance:
Bit per Second 9600, 19200, 38400 bps
Data Bit 8-bit
Parity None
Stop Bit 1
Flow Control None
Port 7000
The terminal software does not return every command input character.
The transmission performance varies with the length of RS-232 cable, please set the baud rate per
Operation commands
Operation command syntax
An operation command is prefixed by character "op", followed by control commands and settings separated b y
space blank [SP], and ended by carriage return pair "CR" and "ASCII hex 0D".Syntax of serial control
commands:
op[SP]<operation command>[SP]<Setting Value>[CR]
Examples:
When sending the multiple commands, make sure the return message of the last command is
received before sending out the next one.
2
RC67711216EN00
DU6771 series DLP Projector Remote Communication Manual
OSD Function
Operation
command
Settings/Return Values
Available when
Picture Mode
pic.mode
? =
Projector is turned on.
Brightness
Bright
?
-
Projector is turned on.
Contrast
contrast
?
-
Projector is turned on.
Saturation
saturat
?
--
Projector is turned on.
Hue
tint
?
-
Projector is turned on.
Sharpness
sharp
?
-
Projector is turned on.
Noise Reduction
nr
?
-
Projector is turned on.
Color Temperature
color.temp
? = 0 = Native
Projector is turned on.
Gamma
gamma
? =
6 = S-Curve
Projector is turned on.
Advance/Input Balance
red.offset
?
-
Projector is turned on.
Advance/Input Balance
green.offset
?
-
Projector is turned on.
List of operation commands
PICTURE
0 = High Bright
1 = Presentation
2 = Video
0-200
=
+
0-200
=
+
0-200
=
+
0-200
=
+
0-31
=
+
Input signal is detected
3D mode is turned off.
Input signal is detected
Input signal is detected
Input signal is detected
Input signal is YUV.
Input signal is detected
Input signal is YUV.
Input signal is detected.
/Red Offset
/Green Offset
=
+
=
+
=
+
0-15
1 = 5400K
2 = 6500K
3 = 7500K
4 = 9300K
0 = 1.0
1 = 1.8
2 = 2.0
3 = 2.2
4 = 2.35
5 = 2.5
0-200
0-200
Input signal is detected.
Input signal is detected
3D Mode is turned off.
Input signal is detected.
Input signal is detected.
Input signal is detected.
RC67711216EN00
3
DU6771 series DLP Projector Remote Communication Manual
Advance/Input Balance
blue.gain
?
-
Projector is turned on.
Advance/Input Balance
red.gain
?
-
Projector is turned on.
Advance/Input Balance
green.gain
?
-
Projector is turned on.
Advance/Input Balance
blue.gain
?
-
Projector is turned on.
Advance/ HSG
hsg.r.gain
?
-
Projector is turned on.
Advance/ HSG
hsg.g.gain
?
-
Projector is turned on.
Advance/ HSG
Hsg.b.gain
?
-
Projector is turned on.
Advance/ HSG
hsg.c.gain
?
-
Projector is turned on.
Advance/ HSG/
hsg.m.gain
?
-
Projector is turned on.
Advance/ HSG
Hsg.y.gain
?
-
Projector is turned on.
Advance/ HSG
hsg.r.sat
?
-
Projector is turned on.
Advance/ HSG
hsg.g.sat
?
-
Projector is turned on.
Advance/ HSG
Hsg.b.sat
?
-
Projector is turned on.
Advance/ HSG
hsg.c.sat
?
-
Projector is turned on.
Advance/ HSG
hsg.m.sat
?
-
/Blue Offset
/Red Gain
/Green Gain
/Blue Gain
/Red Gain
/Green Gain
=
+
=
+
=
+
=
+
=
+
=
+
0-200
0-200
0-200
0-200
0-200
0-200
Input signal is detected.
Input signal is detected.
Input signal is detected.
Input signal is detected.
Input signal is detected.
Input signal is detected.
/Blue Gain
/Cyan Gain
Magenta Gain
/Yellow Gain
/Red/Saturation
/Green/Saturation
=
+
=
+
=
+
=
+
=
+
=
+
0-200
0-200
0-200
0-200
0-200
0-200
Input signal is detected.
Input signal is detected.
Input signal is detected.
Input signal is detected.
Input signal is detected.
Input signal is detected.
/Blue/Saturation
/Cyan/Saturation
/Magenta/Saturati on
RC67711216EN00
=
+
=
+
=
+
0-200
0-200
0-200
4
Input signal is detected.
Input signal is detected.
Input signal is detected
DU6771 series DLP Projector Remote Communication Manual
OSD Function
Operation
command
Settings/Return Values
Note
Advance/ HSG
Hsg.y.sat
?
-
Projector is turned on.
Advance/ HSG
hsg.r.hue
?
-
Projector is turned on.
Advance/ HSG
hsg.g.hue
?
-
Projector is turned on.
Advance/ HSG
Hsg.b. hue
?
-
Projector is turned on.
Advance/ HSG
hsg.c. hue
?
-
Projector is turned on.
Advance/ HSG
hsg.m. hue
?
-
Projector is turned on.
Advance/ HSG
Hsg.y. hue
?
-
Projector is turned on.
Advance/ HSG
hsg.wr.gain
?
-
Projector is turned on.
Advance/ HSG
hsg.wg.gain
?
-
Projector is turned on.
Advance/ HSG
Hsg.wb.gain
?
-
Projector is turned on.
Advance/ HSG
hsg.reset
(execute)
Projector is turned on.
/Yellow/Saturation
/Red/Hue
/Green/Hue
/Blue/Hue
/Cyan/Hue
/Magenta/Hue
=
+
=
+
=
+
=
+
=
+
=
+
0-200
0-200
0-200
0-200
0-200
0-200
Input signal is detected
Input signal is detected
Input signal is detected
Input signal is detected
Input signal is detected
Input signal is detected
/Yellow/Hue
White/Red Gain
/White/Green Gain
/White/Blue Gain
Reset
=
+
=
+
=
+
=
+
0-200
0-200
0-200
0-200
Input signal is detected
Input signal is detected
Input signal is detected
Input signal is detected
Input signal is detected
RC67711216EN00
5
DU6771 series DLP Projector Remote Communication Manual
OSD Function
Operation
command
Settings/Return Values
Note
Input Select
input.sel
? =
5 = HDBaseT
Projector is turned on.
EDID Mode
Edid.mode.hdmi
? = 0 = Default
Projector is turned on.
EDID Mode
Edid.mode.hdmi2
? = 0 = Default
Projector is turned on.
EDID Mode
Edid.mode.dvi
? = 0 = Default
Projector is turned on.
EDID Mode
Edid.mode.vga
? = 0 = Default
Projector is turned on.
EDID Mode
Edid.mode.hdbt
? = 0 = Default
Projector is turned on.
Auto Source
auto.src
? =
Projector is turned on.
SIGNAL
HDMI I
HDMI II
DVI-D
VGA
0 = HDMI I
1 = HDMI II
2 = DVI-D
3 = VGA
4 = Component / BNC
1 = 1024x768@60
2 = 1280x720@60
3 = 1280x800@60
4 = 1280x1024@60
5 = 1600x1200@60
6 = 1680x1050@60
7 = 1920x1080@60
1 = 1024x768@60
2 = 1280x720@60
3 = 1280x800@60
4 = 1280x1024@60
5 = 1600x1200@60
6 = 1680x1050@60
7 = 1920x1080@60
1 = 1024x768@60
2 = 1280x720@60
3 = 1280x800@60
4 = 1280x1024@60
5 = 1600x1200@60
6 = 1680x1050@60
7 = 1920x1080@60
1 = 1024x768@60
2 = 1280x720@60
3 = 1280x800@60
4 = 1280x1024@60
5 = 1600x1200@60
6 = 1680x1050@60
7 = 1920x1080@60
Adjustment is for current input
source.
Adjustment is for current input
source.
Adjustment is for current input
source.
Adjustment is for current input
source.
HDBaseT
RC67711216EN00
1 = 1024x768@60
2 = 1280x720@60
3 = 1280x800@60
4 = 1280x1024@60
5 = 1600x1200@60
6 = 1680x1050@60
7 = 1920x1080@60
0 = Off
1 = On
6
Adjustment is for current input
source.
Loading...