Vivitek D-Point 2, D-Point 3 User Manual

- i -

Contents

1 Accessories of D-Point 2 ................................................................................................. 2

2 Connecting Projector to PC ............................................................................................ 4

3 Pen Action ...................................................................................................................... 4

4 Driver Installation ............................................................................................................ 5

5 Configuration Setting ..................................................................................................... 8

6 D-Point 2 Pull-up Menu ................................................................................................. 12

7 DT01 Multi-touch Interactive Module (Optional) ......................................................... 13

8 Specifications ............................................................................................................... 27

9 Trouble shooting ........................................................................................................... 28

Ver.:2

- 1 -

General Caution

The Interactive utilized precisely designed optical unit. Do not to hide the mirror camera.
The Interactive function operates by infrared 850nm communication. Note the following
important points when using this function.

Do：

 Make sure there is no strong light or sunlight shining on the Interactive camera receiver

or the projection screen.

 Install the projector so that the Interactive camera receiver is not too close to

fluorescent lights.

 The Interactive camera may be interrupted by electromagnetic interference from nearby

equipment (such as electric motors or transformers).

 Clean the front surface of the Interactive regularly so that dust on the front surface does

not influence input ray.

 Clean the front surface, use only fabric and exclusive cleaning liquid for glass.

Do not：

 Put paint or any stickers on the cover of the Interactive camera receiver.
 Use an infrared remote control or infrared microphone in the same room because the

IR Pen may malfunction.

 Use it with wet hands, or in locations where it may get wet. The IR Pen is not

waterproof.

 Hold the pen tip of the IR Pen, and make sure this section does not get damaged.

Otherwise, the IR Pen may not work.

 Press IR Pen strongly when writing. Just touch smoothly like when you draw on

whiteboard with a marker pen.

 Drop the IR Pen. IR Pen tip is designed precisely.
 Operating Keystone, performance for the Interactive function may decline.
 Set lamp mode to “Eco” may cause “Auto Calibration” abnormal operation of the

D-Point 2.

- 2 -

1 Accessories of D-Point 2

D-Point 2 is a built in Interactive Whiteboard on the Projector. To use the D-Point 2
correctly, please find necessary accessories and follow the instructions in this manual.

In the projector box, you will find the following accessories.

Note : Pens Box included “c”, “d” and “e” inside.

a b c

d

e

a. Installation CD : CD contains D-Point 2, i-Draw and User’s manual.
b. USB Cable : Type A to mini USB cable for connect the Projector to PC.
c. IR Pen : IR Pen is a pen type wireless mouse. Before using the pen, insert batteries

correctly.
d. Battery : AAA size battery.
e. Extra Pen Tip : 4 extra pen tips included

Caution:

When inserting battery into the IR Pen, make sure the battery polarity is correct.

1. Only use AAA batteries (Alkaline batteries are recommended).

2. Dispose of used batteries according to local ordinance regulations.

3. Remove the batteries when not using the D-Point 2 for prolonged periods.

- 3 -

1.1 Installing CHANGEABLE TIPS

Clenched and forced to pull out the
tip.

Installing a new Pen Tip until you feel
it click with Pen.

Complete the replacement tip.

- 4 -

2 Connecting Projector to PC

Connect the Projector to a PC via the supplied USB cable. Plug mini USB to Projector
MINI USB connector and other end to PC.

Note：

1. In the accessories, a 5m USB cable is provided. If more than 5 meter USB cable
length is required, then use repeater cable to extend the USB cable length.

2. Do not connect the projector with the PC when D-Point 2 driver install.

3 Pen Action

IR Pen provides four actions, Click, Double Click, Right Button Click and Drag.

Click : Touch an icon or a menu on the screen.
Double Click : Touch an icon or a menu on the screen twice.
Right Button Click : Touch an icon or menu 1.5 seconds or more.
Drag : Touch and drag an object on the screen

- 5 -

4 Driver Installation

System Requirements

Operating system

- Windows XP, Vista, Windows 7, Windows 8

Hardware

PC requirements

REQUIREMENT

CPU

higher than Pentium

RAM

higher than 512MB

Hard Disk

higher than 100MB

USB

USB 2.0

CD-ROM

higher than 8x

Display

Resolutions no lower than XGA (1024x768) and no higher than WUXGA
(1920x1200), Display color in16-bit color or greater.

Insert the D-Point 2 CD into your CD/DVD-ROM driver. The Installation assistant will run
automatically. Follow the instructions in the installation assistant. If the assistant does
not run automatically, double click the “ setup.exe” under CD/DVD-ROM directory and
the Installation assistant will run.

4.1 Click Install D-Point 2 in the installation assistant.

4.2 Select a language and click “OK”.

- 6 -

4.3 The installation dialog box will appear. Click next. During installation,
it is recommended to close other applications.

4.4 Click Install, installation begins.

4.5 Installation ends, then dialog box will indicate finish. Click “Finish”.

- 7 -

When Installation is finished,

 D-Point 2 icon will be created on the desktop.
 Installation folder will be created on C: directory.

Upon starting D-Point 2, the configuration window will appear on the desktop to assist in setting
up the D-Point 2 configuration