Vivitek DK8500Z User Manual
DK8500Z
Remote Communicaton
Manual
DK8500Z DLP Projector Remote Communication Manual
1
RM85001117EN00
Table of Contents
The Serial Interface RS-232 Command ........................................................................................ 2
Communication parameter ......................................................................................................................................... 2
Operation commands ................................................................................................................................................. 2
Operation command syntax ................................................................................................................................ 2
List of operation commands ............................................................................................................................... 3
Simulated IR remote controller commands .............................................................................................................. 14
Control the Projector Through a Network .................................................................................. 15
Cable connection ..................................................................................................................................................... 15
Set up the projector for networking .......................................................................................................................... 16
Control the projector through a network .................................................................................................................. 17
Control the projector through a web browser ................................................................................................... 17
Control projector with TCP/IP communication protocol .................................................................................... 23
About Vivitek Support ................................................................................................................. 24
DK8500Z DLP Projector Remote Communication Manual
2
RM85001117EN00
The Serial Interface RS-232 Command
This projector supports to control by RS-232 command, there exist two types of RS-232 serial commands:
Operation command: Available menu options are INPUT, PICTURE, ALIGNMENT, CONTROL and SERVICE.
Simulated IR remote controller commands: Controls projector via RS-232 command, the commands simulate IR
remote controller and its control keys.
Communication parameter
You can use the serial control command to input commands for projector control or retrieve its operational data
through Windows client terminal software, e.g. Hyper Terminal, with ASCII characters. You need to set up the following
communication parameters in advance:
Item Parameter:
Bit per Second 9600 bps
Data Bit 8-bit
Parity None
Stop Bit 1
Flow Control None
Port 7000
Note:
The terminal software does not return every command input character
The transmission performance varies with the length of RS-232 cable
Operation commands
Operation command syntax
An operation command is prefixed by character "op", followed by control commands and settings separated by
space blank [SP], and ended by carriage return pair "CR" and "ASCII hex 0D".Syntax of serial control
commands:
op[SP]<operation command>[SP]<Setting Value>[CR]
op :
A constant indicating this is an operation command.
[SP] :
Indicate one blank space.
[CR] :
Indicate the command ending carriage return pair "CR" and "ASCII hex 0D".
Setting value :
Settings of operation command
Types of setup strings Characters of settings Description
Query current setup ? Question mark "?" indicates querying current setup
Setup = <settings> Syntax: Symbol "=" suffixed with setup values
Increase setup order of
adjustment items
+ Some settings are changed in steps. Symbol "+"
indicates changing one step up
Decrease setup order of
adjustment items
- Some settings are changed in steps. Symbol "-"
indicates changing one step down
Execute operation command None Certain operation commands execute after input
without further setting or regulators.
Examples:
Control items Input command Projector return message
Query current brightness op bright ? [CR] OP BRIGHT = 101
Set up brightness op bright = 127 [CR] OP BRIGHT = 127
Set up input signal source to
HDMI
op input.sel = 0 [CR] OP INPUT.SEL = 0
Reset projection lens to
center position
lens.center
Note:
When sending the multiple commands, make sure the return message of the last command is received
before sending out the next one.
DK8500Z DLP Projector Remote Communication Manual
3
RM85001117EN00
List of operation commands
INPUT
OSD Function Operation
command
Settings/Return Values Note
Input Select input.sel ? = 0 = HDMI 1
1 = HDMI 2
3 = HDBaseT
4 = 3G-SDI
Not applicable when the project is at
standby mode
PIP/PIP Option pip ? = 0 = Off
1 = On
Not applicable when the project is at
standby mode and 3D mode
PIP/PIP Input pip.sel ? = 0 = HDMI 1
1 = HDMI 2
3 = HDBaseT
4 = 3G-SDI
Not applicable when the project is at
standby mode or PIP option is set to
Off.
PIP/ Position pip.pos ? = 0 = Top Left
1 = Top Right
2 = Bottom Left
3 = Bottom Right
4 = PBP
Not applicable when the project is at
standby mode or PIP is set to Off.
Auto Source auto.src ? = 0 = Off
1 = On
Not applicable when the projector is
at standby mode.
Auto Sync Auto.mg (execute) Available when source is locked.
Color Space color.space ? = 0 = Auto
1 = YPbPr (Rec. 709)
2 = YcbCr (Rec. 601)
3 = RGB-PC (0-255)
4 = RGB-Video (16-235)
Available when source is locked.
Aspect Ratio aspect ? = 0 = 5:4
1 = 4:3
2 = 16:10
3 = 16:9
4 = 1.88
5 = 2.35
6 = LetterBox
7 = Source
8 = Native
Available when the source is locked.
VGA Setup/H Total h.total ?
=
+
-
0-200
Available when the source is locked
Or Input source is VGA or
Component(RGBHV)
VGA Setup/H Start h.pos ?
=
+
-
0-200
Available when the source is locked
Or Input source is VGA or
Component(RGBHV)
VGA Setup/H Phase h.phase ?
=
+
-
0-200 Available when the source is locked.
Input source is VGA or
Component(RGBHV)
VGA Setup/V Start v.pos ?
=
+
-
0-200 Available when the source is locked.
Input source is VGA or
Component(RGBHV)
DK8500Z DLP Projector Remote Communication Manual
4
RM85001117EN00
OSD Function Operation
command
Settings/Return Values Note
Test Pattern pattern ? = 0 = Off
1 = CrossHatch
2 = Color Bar
3 = Checkboard
4 = H Burst
5 = V Burst
6 = White
7 = Red
8 = Green
9 = Blue
10 = Black
Not applicable when the project is at
standby mode.
3D/3D Format 3d.format = ? 0 = Off
1 = Auto
2 = Side-By-Side (Half)
3 = Top-And-Bottom
4 = Frame Sequential
Not applicable when the project is at
standby model.
3D/Eye Swap 3d.swap = ? 0 = Normal
1 = Reverse
Applicable when the projector is at
3D mode.
3D/DLP Link 3d.dlplink = ? 0 = Off
1 = On
Applicable when 3D.Darktime is set
to 2 (1.95ms)
3D/Dark Time 3d.darktime = ? 0 = 0.65 ms
1 = 1.3 ms
2 = 1.95 ms
Applicable when the projector is at
3D mode.
3D/sync delay 3d.syncdelay = ? 1 – 60 Applicable when the projector is at
3D mode.
3D/Sync Reference 3d.syncref = ? 0 = External
1 = Internal
2 = Auto
Not applicable when the project is at
standby mode.
PICTURE
OSD Function
Operation
command
Settings/Return Values Note
Picture Mode pic.mode ?
=
0 = High Bright
1 = Presentation
2 = Video
Not applicable when the project is at
standby mode.
Brightness bright ?
=
+
-
0-200 Not applicable when the project is at
standby mode or the input signal is
not locked yet.
Contrast contrast ?
=
+
-
0-200 Not applicable when the project is at
standby mode or the input signal is
not locked yet.
Saturation saturat ?
=
+
--
0-200 Apply for YUV signal input
Not applicable if the input signal is
not locked yet.
Hue tint ?
=
+
-
0-200 Apply for YUV signal input
Not applicable if the input signal is
not locked yet.
Sharpness sharp ?
=
+
-
0-10 Not applicable when the project is in
standby mode or the input signal is
not locked yet.
DK8500Z DLP Projector Remote Communication Manual
5
RM85001117EN00
OSD Function
Operation
command
Settings/Return Values Note
Noise Reduction nr ?
=
+
-
0 = Off
1 = Low
2 = Middle
3 = High
Not applicable when the project is at
standby mode.
Color Temperature color.temp ?
=
0 = 5400K
1 = 6500K
2 = 7500K
3 = 9300K
4 = Native
Not applicable at 3D mode
Gamma gamma ?
=
0 = 1.0
1 = 1.8
2 = 2.0
3 = 2.2
4 = 2.35
5 = 2.5
6 = S-Curve
7 = DICOM
8 = HDR-PQ400
9 = HDR-PQ500
10 = HDR-PQ1000
11 = HDR-HLG
Not applicable when the project is at
standby mode or the input signal is
not locked yet.
Overscan zoom ?
=
0 = Off
1 = Crop
2 = Zoom
Not applicable when the project is at
standby mode or the input signal is
not locked yet.
Input Balance /Red
Offset
red.offset ?
=
+
-
0-200 Available when the input source is
locked.
Input Balance /Green
Offset
green.offset ?
=
+
-
0-200 Available when the input source is
locked.
Input Balance /Blue
Offset
blue.gain ?
=
+
-
0-200 Available when the input source is
locked.
Input Balance /Red
Gain
red.gain ?
=
+
-
0-200 Available when the input source is
locked.
Input Balance /Green
Gain
green.gain ?
=
+
-
0-200 Available when the input source is
locked.
Input Balance /Blue
Gain
blue.gain ?
=
+
-
0-200 Available when the input source is
locked.
HSG/Red Gain hsg.r.gain ?
=
+
-
0-200 Available when the input source is
locked.
DK8500Z DLP Projector Remote Communication Manual
6
RM85001117EN00
OSD Function
Operation
command
Settings/Return Values Note
HSG/Green Gain hsg.g.gain ?
=
+
-
0-200 Available when the input source is
locked.
HSG/Blue Gain hsg.b.gain ?
=
+
-
0-200 Available when the input source is
locked.
HSG/Cyan Gain hsg.c.gain ?
=
+
-
0-200 Available when the input source is
locked.
HSG/Magenta Gain hsg.m.gain ?
=
+
-
0-200 Available when the input source is
locked.
HSG/Yellow Gain hsg.y.gain ?
=
+
-
0-200 Available when the input source is
locked.
HSG/Red/Saturation hsg.r.sat ?
=
+
-
0-200 Available when the input source is
locked.
HSG/Green/Saturation hsg.g.sat ?
=
+
-
0-200 Available when the input source is
locked.
HSG/Blue/Saturation hsg.b.sat ?
=
+
-
0-200 Available when the input source is
locked.
HSG/Cyan/Saturation hsg.c.sat ?
=
+
-
0-200 Available when the input source is
locked.
HSG/Magenta/
Saturation
hsg.m.sat ?
=
+
-
0-200 Available when the input source is
locked.
HSG/Yellow/Saturation Hsg.y.sat ?
=
+
-
0-200 Available when the input source is
locked.
HSG/Red/Hue hsg.r.hue ?
=
+
-
0-200 Available when the input source is
locked.
HSG/Green/Hue hsg.g.hue ?
=
+
-
0-200 Available when the input source is
locked.
HSG/Blue/Hue Hsg.b. hue ?
=
+
-
0-200 Available when the input source is
locked.
DK8500Z DLP Projector Remote Communication Manual
7
RM85001117EN00
OSD Function
Operation
command
Settings/Return Values Note
HSG/Cyan/Hue hsg.c. hue ?
=
+
-
0-200 Available when the input source is
locked.
HSG/Magenta/Hue hsg.m. hue ?
=
+
-
0-200 Available when the input source is
locked.
HSG/Yellow/Hue Hsg.y. hue ?
=
+
-
0-200 Available when the input source is
locked.
HSG/White/Red Gain hsg.wr.gain ?
=
+
-
0-200 Available when the input source is
locked.
HSG/White/Green Gain hsg.wg.gain ?
=
+
-
0-200 Available when the input source is
locked.
HSG/White/Blue Gain Hsg.wb.gain ?
=
+
-
0-200 Available when the input source is
locked.
HSG Reset hsg.reset (execute)
Available when the input source is
locked.
Dynamic Black dblack ?
=
0 = Off
1 = On
Not applicable when the projector is
at below condition:
- Standby mode.
- Edge Blend is On
- 3D mode
- Dynamic Black is off
Freeze freeze ?
=
0 = Off
1 = On
Not applicable when the projector is
at standby mode
Alignment
OSD Function Operation
command
Settings/Return Value Note
Lens control
Zoom
zoom.in (execute) Not applicable when the projector is
at standby mode
Lens control
Zoom
zoom.in.2 (execute) Not applicable when the projector is
at standby mode.
Lens control
Zoom In
zoom.in.3 (execute) Not applicable when the projector is
at standby mode.
Lens control
Zoom Out
zoom.out (execute) Not applicable when the projector is
at standby mode.
Lens control
Zoom Out
zoom.out.2 (execute) Not applicable when the projector is
at standby mode.
Lens control
Zoom Out
zoom.out.3 (execute) Not applicable when the projector is
at standby mode.
Lens control
Focus near
focus.near (execute) Not applicable when the projector is
at standby mode
Loading...