Vivitek D963HD PLUS User Manual
D963HD Plus
Copyright
Ver.:01
This publication, including all photographs, illustrations and software, is protected under international
copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may
be reproduced without written consent of the author.
© Copyright 2015
Disclaimer
The information in this document is subject to change without notice. The manufacturer makes no
representations or warranties with respect to the contents hereof and specifically disclaims any implied
warranties of merchantability or fitness for any particular purpose. The manufacturer reserves the right to
revise this publication and to make changes from time to time in the content hereof without obligation of
the manufacturer to notify any person of such revision or changes.
Trademark Recognition
Kensington is a U.S. registered trademark of ACCO Brand Corporation with issued registrations
and pending applications in other countries throughout the world.
HDMI, the HDMI Logo, and High-Definition Multimedia Interface are trademarks or
registered trademarks of HDMI Licensing LLC in the United States and other countries.
All other product names used in this manual are the properties of their respective owners and are
acknowledged.
— i —
Important Safety Information
Important:
It is strongly recommended that you read this section carefully before using the projector. These
safety and usage instructions will ensure that you enjoy many years of safe use of the projector.
Keep this manual for future reference.
Symbols Used
Warning symbols are used on the unit and in this manual to alert you of hazardous situations.
The following styles are used in this manual to alert you to important information.
Note:
Provides additional information on the topic at hand.
Important:
Provides additional information that should not be overlooked.
Caution:
Alerts you to situations that may damage the unit.
Warning:
Alerts you to situations that may damage the unit, create a hazardous environment, or cause
personal injury.
Throughout this manual, component parts and items in the OSD menus are denoted in bold font as in this
example:
“Push the Menu button on the remote control to open the Main menu.”
General Safety Information
Do not open the unit case. Aside from the projection lamp, there are no user-serviceable parts in
the unit. For servicing, contact qualified service personnel.
Follow all warnings and cautions in this manual and on the unit case.
The projection lamp is extremely bright by design. To avoid damage to eyes, do not look into the
lens when the lamp is on.
Do not place the unit on an unstable surface, cart, or stand.
Avoid using the system near water, in direct sunlight, or near a heating device.
Do not place heavy objects such as books or bags on the unit.
— ii —
Projector Installation Notice
15
°
-15°
Minimum 500mm
(19.69 inch)
Minimum 500mm
(19.69 inch)
Minimum 500mm
(19.69 inch)
Minimum 500mm
(19.69 inch)
Minimum 100mm
(3.94 inch)
Minimum 300mm
(11.81 inch)
Place the projector in a horizontal position
The tilt angle of the projector should not exceed 15 degrees, nor should the projector be
installed in any way other than the desktop and ceiling mount, otherwise lamp life could decrease
dramatically, and may lead to other unpredictable damages.
Allow at least 50 cm clearance around the exhaust vent.
Ensure that the intake vents do not recycle hot air from the exhaust vent.
When operating the projector in an enclosed space, ensure that the surrounding air temperature
within the enclosure does not exceed operation temperature while the projector is running, and the
air intake and exhaust vents are unobstructed.
All enclosures should pass a certified thermal evaluation to ensure that the projector does not
recycle exhaust air, as this may cause the device to shutdown even if the enclosure temperature is
with the acceptable operation temperature range.
–iii –
Verify Installation Location
To supply power, the 3-blade (with earthing lead) socket should be used to ensure proper
grounding and equalized ground potential for all of the equipment in the Projector System.
The power code provided with the Projector should be used. In case of any missing item, other
qualified 3-blade (with earthing lead) power cord can be used as substitution; however, do not use
2-blade power cord.
Verify if the voltage is stable, grounded properly and there is no electricity leakage.
Measure total power consumption which should not higher the safety capacity and avoid safety
issue and short circuit.
Turn on Altitude Mode when located in high altitude areas
The projector can only be installed upright or inverted.
When installation the bracket, make sure the weight limit is not exceed and firmly secured.
Avoid installing near air conditioner duct or subwoofer.
Avoid installing at high temperature, insufficient cooling and heavy dust locations.
Keep your product away from fluorescent lamps to avoid malfunction
caused by IR interference
The VGA IN connector should be connected to the VGA IN port. Note that it should be inserted
tightly, with the screws on both sides securely fastened to ensure proper connection of the signal
wire for achieving optimal display effect.
The AUDIO IN connector should be connected to the AUDIO IN port and CANNOT be connected
to AUDIO OUT or other ports like BNC, RCA; otherwise, it will lead to mute output and even
DAMAGE the port.
Install the projector above 200cm to avoid damage.
The power cord and signal cable should be connected before power on the projector. During the
projector starting and operating process, DO NOT insert or remove the signal cable or the power
cord to avoid damaging the projector.
Cooling notes
Air outlet
Make sure the air outlet is 50cm clear of any obstruction to ensure proper cooling.
Air outlet location should not be in front of the lens of other projector to avoid causing illusions.
Keep the outlet at least 100cm away from the inlets of other projectors
The projector generates a massive amount of heat during use. The internal fan dissipates the heat
of the projector when shutting down, and such process may continue for a certain period. After the
project enters STANDBY MODE status, press the AC power button to turn off the projector and
remove the power cord. DO NOT remove the power cord during the shutdown process, as it may
cause damage to the projector. In the meantime, the delayed heat radiating will also affect the
service life of the projector. The shutdown process may vary depending on the model used.
Whatever the case may be, be sure to disconnect the power cord till after the projector enters the
STANDBY status.
Air inlet
Make sure there is no object blocking air input within 30 cm.
Keep the inlet away from other heat sources
Avoided heavy dust area
— iv —
Power Safety
DISPOSAL: Do not use household or municipal waste collection services for
disposal of electrical and electronic equipment. EU countries require the use
of separate recycling collection services.
Only use the supplied power cord.
Do not place anything on the power cord. Place the power cord where it will not be in the way of
foot traffic.
Remove the batteries from the remote control when storing or not in use for a prolonged period.
Replacing the Lamp
Replacing the lamp can be hazardous if done incorrectly. See Replacing the Projection Lamp on page 49
for clear and safe instructions for this procedure. Before replacing the lamp:
Unplug the power cord.
Allow the lamp to cool for about one hour.
Caution:
In rare cases the lamp bulb may burn out during normal operation and cause glass dust or shards
to be discharged outward from the rear exhaust vent.
Do not inhale or do not touch glass dust or shards. Doing so could result in injury.
Always keep your face away from the exhaust vent so that you do not suffer from the gas and
broken shards of the lamp.
Cleaning the Projector
Unplug the power cord before cleaning. See Cleaning the Projector page 52.
Allow the lamp to cool for about one hour.
Regulatory Warnings
Before installing and using the projector, read the regulatory notices in the Regulatory Compliance on
page 65.
Important Recycle Instructions:
Lamp(s) inside this product contain mercury. This product may contain other electronic waste that
can be hazardous if not disposed of properly. Recycle or dispose in accordance with local, state, or federal
Laws. For more information, contact the Electronic Industries Alliance at WWW.EIAE.ORG. For lamp
specific disposal information check WWW.LAMPRECYCLE.ORG.
Symbol Explanations
–v –
Table of Contents
GETTING STARTED .............................................................................................................................................. 1
PACKING CHECKLIST ............................................................................................................................................. 1
VIEWS OF PROJECTOR PARTS ................................................................................................................................ 2
Front-right View ............................................................................................................................................... 2
Limited lens shift .............................................................................................................................................. 3
Top view—On-screen Display (OSD) buttons and LEDs ................................................................................ 4
Rear view ......................................................................................................................................................... 5
Bottom view ..................................................................................................................................................... 7
REMOTE CONTROL PARTS ..................................................................................................................................... 8
REMOTE CONTROL OPERATING RANGE ................................................................................................................ 10
PROJECTOR AND REMOTE CONTROL BUTTONS ..................................................................................................... 10
INSERTING THE REMOTE CONTROL BATTERIES ..................................................................................................... 11
SETUP AND OPERATION ................................................................................................................................... 12
STARTING AND SHUTTING DOWN THE PROJECTOR ................................................................................................ 12
SETTING AN ACCESS PASSWORD (SECURITY LOCK) .............................................................................................. 14
ADJUSTING THE PROJECTOR LEVEL ..................................................................................................................... 16
ADJUSTING THE ZOOM, FOCUS AND KEYSTONE ..................................................................................................... 17
ADJUSTING THE VOLUME ..................................................................................................................................... 18
ON-SCREEN DISPLAY (OSD) MENU SETTINGS.............................................................................................. 19
OSD MENU CONTROLS ....................................................................................................................................... 19
Navigating the OSD ....................................................................................................................................... 19
SETTING THE OSD LANGUAGE ............................................................................................................................. 20
OSD MENU OVERVIEW ........................................................................................................................................ 21
IMAGE MENU ....................................................................................................................................................... 24
Computer Menu ............................................................................................................................................. 25
Advanced Feature ......................................................................................................................................... 26
Color Manager ............................................................................................................................................... 27
SETTINGS 1 MENU ............................................................................................................................................... 28
Audio.............................................................................................................................................................. 29
Advanced 1 Feature ...................................................................................................................................... 30
Advanced 2 Feature ...................................................................................................................................... 32
SETTINGS 2 MENU ............................................................................................................................................... 33
Status............................................................................................................................................................. 34
Advanced 1 Feature ...................................................................................................................................... 35
Advanced 2 Feature ...................................................................................................................................... 47
MAINTENANCE AND SECURITY ....................................................................................................................... 49
REPLACING THE PROJECTION LAMP ..................................................................................................................... 49
Resetting the Lamp ....................................................................................................................................... 51
CLEANING THE PROJECTOR ................................................................................................................................. 52
Cleaning the Lens .......................................................................................................................................... 52
Cleaning the Case ......................................................................................................................................... 52
USING THE KENSINGTON SECURITY SLOT & USING THE SECURITY BAR ................................................................. 53
Using the Kensington Security Slot ............................................................................................................... 53
Using the Security Bar ................................................................................................................................... 53
TROUBLESHOOTING ......................................................................................................................................... 54
COMMON PROBLEMS AND SOLUTIONS ................................................................................................................... 54
TIPS FOR TROUBLESHOOTING .............................................................................................................................. 54
LED ERROR MESSAGES ...................................................................................................................................... 55
IMAGE PROBLEMS ............................................................................................................................................... 55
LAMP PROBLEMS ................................................................................................................................................. 56
REMOTE CONTROL PROBLEMS ............................................................................................................................. 56
AUDIO PROBLEMS ............................................................................................................................................... 57
HAVING THE PROJECTOR SERVICED ..................................................................................................................... 57
HDMI Q & A ....................................................................................................................................................... 58
— vi —
SPECIFICATIONS ................................................................................................................................................ 59
SPECIFICATIONS .................................................................................................................................................. 59
PROJECTION DISTANCE VS. PROJECTION SIZE ...................................................................................................... 60
Projection Distance and Size Table .............................................................................................................. 60
TIMING MODE TABLE ........................................................................................................................................... 62
PROJECTOR DIMENSIONS .................................................................................................................................... 64
REGULATORY COMPLIANCE ........................................................................................................................... 65
FCC WARNING ................................................................................................................................................... 65
CANADA .............................................................................................................................................................. 65
SAFETY CERTIFICATIONS ..................................................................................................................................... 65
APPENDIX I ......................................................................................................................................................... 66
RS-232C PROTOCOL .......................................................................................................................................... 66
APPENDIX II ........................................................................................................................................................ 71
DX977 / DH976 / DU978 FAMILY ........................................................................................................................ 71
–vii –
GETTING STARTED
DLP PROJECTOR
REMOTE CONTROL
(WITH TWO AAA BATTERIES)
LENS CAP
RGB CABLE
POWER CORD
CARRYING CASE
CD-ROM
(THIS USER’S MANUAL)
QUICK START GUIDE
WARRANTY CARD
Packing Checklist
Carefully unpack the projector and check that the following items are included:
Contact your dealer immediately if any items are missing, appear damaged, or if the unit does not work. It
is recommend that you keep the original packing material should you ever need to return the equipment
for warranty service.
Caution:
Avoid using the projector in dusty environments.
– 1 –
Views of Projector Parts
ITEM
LABEL
DESCRIPTION
SEE PAGE
1.
Height-adjuster button
Push to release height adjuster
16
2.
Height adjuster
Adjusts level of projector
3.
Lens
Projection Lens
4.
IR receiver
Receive IR signal from remote control
8
5.
Focus ring
Focuses the projected image
17
6.
Zoom ring
Enlarges the projected image
7.
Manual Lens shift
For Image vertical shift adjustment
3
8.
Function keys
See Top view—On-screen Display (OSD)
buttons and LEDs.
4
1 2 3 4
5
6
7
Front-right View
Important:
Ventilation openings on the projector allow for good air circulation, which keeps the projector lamp
cool. Do not obstruct any of the ventilation openings.
— 2 —
Limited lens shift
DX977
A 8% 15.8% 9%
B 2.5% 3.8% 3.1%
To shift up the projection image, twist the
adjusters counter clockwise
DH976 / D963HD Plus
To shift down the projection image , twist the
adjusters clockwise
DU978
— 3 —
Top view—On-screen Display (OSD) buttons and LEDs
ITEM
LABEL
DESCRIPTION
SEE PAGE
1.
(Power button)
Turns the projector On or Off.
12
2.
BLANK
Displays a blank screen and mutes audio
3.
◄ (Left cursor) /
Volume-
Navigates and changes settings in the OSD
Quick Menu – For Volume
19
4.
Enter
Enter or confirm highlighted OSD menu item
5.
MENU
Opens and exits OSD menus
6.
▲ (Up cursor) /
Keystone+
Navigates and changes settings in the OSD
Quick Menu – For Keystone
7.
AUTO
Optimizes image size, position, and resolution
8.
► (Right cursor) /
Volume+
Navigates and changes settings in the OSD
Quick Menu – For Volume
19
9.
SOURCE
Enter the Source menu
10.
▼ (Down cursor) /
Keystone-
Navigates and changes settings in the OSD
Quick Menu – For Keystone
19
11.
LAMP LED
Flashing
Lamp is not ready (warming up/shutting down/cooling)
(see LED Error Messages on page 55)
12.
TEMP LED
Flashing
Error code
1
2
3
4
5
7
8
6
9
10
11
— 4 —
Rear view
ITEM
LABEL
DESCRIPTION
SEE PAGE
1.
AC IN
Connect the POWER cable
12
2.
(USB)
Connect the USB cable from a computer
3.
VGA OUT
Connect the RGB cable to a display
(Loop Thru only for VGA IN-1)
4.
LAN
Connect a LAN cable from Ethernet
5.
VGA IN 1
Connect the RGB cable from a computer or component device
6.
VGA IN 2
Connect the RGB cable from a computer or component device
7.
DP
Connect a DISPLAYPORT CABLE from a DISPLAYPORT device
8.
AUDIO IN
Connect an AUDIO cable from audio device
9.
HDMI 1 / 2
Connect the HDMI cable from a HDMI device
10.
3D SYNC
Connect the 3D IR glasses transmitter
(Note: For Vivitek brand 3D IR glasses only)
11.
DC 12V TRIGGER
When connected to the screen through a commercially available cable,
the screen deploys automatically on start up of the projector. The screen
retracts when the projector is powered off (see notes below).
12.
Speaker
Outputs audio sound
13.
Kensington Security
Slot
53
14.
VIDEO IN
Connect the COMPOSITE cable from a video device
15.
AUDIO IN (L and R)
Connect the AUDIO cable from a audio device
16.
S-VIDEO IN
Connect the S-Video cable from a video device
17.
RS-232C
Connect RS-232 serial port cable for remote control
18.
AUDIO OUT
Connect an AUDIO cable to audio amplifier
1 2
3 4
5
6 7 9 10 11
13
14
15
16
12
8
1718
Secure to permanent object with a Kensington Lock
system
– 5 –
Note:
To use this feature, you must plug in the connector before turn on/off the projector.
Screen controllers are supplied and supported by screen manufacturers.
Do not use this jack for anything other than intended use.
Note:
If your video equipment has both S-VIDEO and RCA jacks (composite video) connect to the
S-VIDEO connector. S-VIDEO provides a better quality signal.
Warning:
As a safety precaution, disconnect all power to the projector and connecting devices before making
connections.
— 6 —
Bottom view
ITEM
LABEL
DESCRIPTION
SEE PAGE
1.
Tilt adjustor
Rotate adjuster lever to adjust angle position.
16
2.
Ceiling support holes
Contact your dealer for information on mounting the projector on a
ceiling
3.
Height adjustor
Adjuster drops down when adjuster button is
pushed.
16
4.
Height adjustor button
Push to release adjustor.
Note:
When installing, ensure that you use only UL Listed ceiling mounts.
For ceiling installations, use approved mounting hardware and M4 screws with a maximum screw
depth of 6 mm (0.23 inch).
The construction of the ceiling mount must be of a suitable shape and strength. The ceiling mount
load capacity must exceed the weight of the installed equipment, and as an additional precaution
be capable of withstanding three times the weight of the equipment (not less than 5.15 kg) over a
period of 60 seconds.
– 7 –
Remote Control Parts
Important:
1. Avoid using the projector with bright fluorescent lighting turned on. Certain high-frequency
fluorescent lights can disrupt remote control operation.
2. Be sure nothing obstructs the path between the remote control and the projector. If the path
between the remote control and the projector is obstructed, you can bounce the signal off certain
reflective surfaces such as projector screens.
3. The buttons and keys on the projector have the same functions as the corresponding buttons on
the remote control. This user’s manual describes the functions based on the remote control.
Note:
Complies with FDA performance standards for laser products except for deviations pursuant to
Laser Notice No. 50, dated June 24, 2007
— 8 —
ITEM
LABEL
DESCRIPTION
SEE PAGE
1.
IR transmitter
Transmits signals to projector
2.
Status LED
Lights when the remote control is used
3.
Laser
Press to operate the on-screen pointer
4.
Up
Up arrow when connected through USB to a PC
(Not available in this series)
5.
Right
Right arrow when connected through USB to a PC
(Not available in this series)
6.
Down
Down arrow when connected through USB to a PC
(Not available in this series)
7.
Page Down
Page down when connected through USB to a PC
(Not available in this series)
8.
Up cursor
Navigates and changes settings in the OSD
19
9.
Right cursor
10.
Down cursor
11.
Volume +/-
Adjusts volume
18
12.
Mute
Mutes the built-in speaker
13.
Zoom+
Zoom in
14.
Zoom-
Zoom out
15.
Freeze
Freeze/unfreezes the on-screen picture
16.
Blank
Makes the screen blank
17.
Source
Detects the input device
18.
Auto
Auto adjustment for phase, tracking, size, position
19.
Menu
Opens the OSD
19
20.
Status
Opens the OSD Status menu (the menu only opens when
an input device is detected)
34
21.
Keystone top/bottom
Corrects image-trapezoid (wider top/bottom) effect
17
22.
Left cursor
Navigates and changes settings in the OSD
19
23.
Enter
Changes settings in the OSD
24.
Page Up
Page up when connected through USB to a PC
(Not available in this series)
25.
Left
Left arrow when connected through USB to a PC
(Not available in this series)
26.
Enter
Enter key when connected through USB to a PC
(Not available in this series)
27.
Power
Turns the projector on or off
12
28.
Laser
Use as on-screen pointer. DO NOT POINT IN EYES.
Caution:
Use of controls, adjustments or performance of procedures other than those specified herein may
result in hazardous laser light exposure.
– 9 –
Remote Control Operating Range
The remote control uses infrared transmission to control the projector. It is not necessary to point the
remote directly at the projector. Provided you are not holding the remote perpendicular to the sides or
the rear of the projector, the remote will function well within a radius of about 7 meters (23 feet) and
15 degrees above or below the projector level. If the projector does not respond to the remote control,
move a little closer.
Projector and Remote Control Buttons
The projector can be operated using the remote control or the buttons on the top of the projector. All
operations can be carried out with the remote control; however, the buttons on the projector are
limited in use.
— 10 —
Inserting the Remote Control Batteries
1.
Remove the battery compartment
cover by sliding the cover in the
direction of the arrow.
2.
Insert the battery with the positive
side facing up.
3.
Replace the cover.
Caution:
1. Only use AAA batteries (Alkaline batteries are recommended).
2. Dispose of used batteries according to local ordinance regulations.
3. Remove the batteries when not using the projector for prolonged periods.
– 11 –
Starting and Shutting down the Projector
1.
Connect the power cord to the
projector. Connect the other end to
a wall outlet.
The POWER LED on the
projector light.
2.
Turn on the connected devices.
3.
Ensure the POWER LED not a
flashing. Then press the POWER
button to turn on the projector.
The projector splash screen displays
and connected devices are
detected.
See Setting an Access Password
(Security Lock) on page 14 if
security lock is enabled.
4.
If more than one input device is
connected, press the SOURCE
button and use ▲▼ to scroll among
devices.
(Component is supported through
the RGB to COMPONENT
ADAPTER.)
HDMI 1 / HDMI 2: High-Definition Multimedia
Interface 1 / 2
DisplayPort: DisplayPort
VGA 1 / VGA 2: Analog RGB1 / RGB 2
S-Video: Super video (Y/C separated)
Composite Video: Traditional composite video
SETUP AND OPERATION
— 12 —
5.
When the “Power Off? /Press
Power again” message appears,
press the POWER button. The
projector turns off.
Caution:
1. Be sure to remove the lens cap before starting projector.
2. Do not unplug the power cord until all of fans are stop–indicating the projector has cooled down.
– 13 –
Setting an Access Password (Security Lock)
1.
Press the MENU button to open the
OSD menu.
2.
Press the cursor ◄► button to move
to the Settings 1 menu, press the
cursor ▲▼ button to select Advanced
1.
3.
Press (Enter) / ► to enter the
Advanced 1 sub menu. Press the
cursor ▲▼ button to select Security
Lock.
4.
Press the cursor ◄► button to enter
and enable or disable security lock
function.
A password dialog box automatically
appears.
You can use the four (arrow) buttons to set a password and prevent unauthorized use of the projector.
When enabled, the password must be entered after you power on the projector. (See Navigating the
OSD on page 19 and Setting the OSD Language on page 20 for help on using OSD menus.)
Important:
Keep the password in a safe place. Without the password, you will not be able to use the projector.
If you lose the password, contact your reseller for information on clearing the password.
— 14 —
5.
You can use the cursor buttons
▲▼◄►
either on keypad or IR remote control
for password entry. You can use any
combination including the same arrow
five times, but not less than five.
Press the cursor buttons in any order
to set the password. Push the MENU
button to exit the dialog box.
6.
The password confirm menu appears
when user presses the power-on key
in case the Security Lock is enabled.
Enter the password in the order you
set it at step 5. In case you forget the
password, please contact the service
center.
The service center will validate the
owner and help reset the password.
– 15 –
Adjusting the Projector Level
1.
To raise the level of the projector, lift the projector [A] and press the heightadjuster button [B].
The height adjuster drops down [C].
2.
To lower the level of the projector, press the height-adjuster button and push
down on the top of the projector.
3.
To adjust the angle of the picture, turn the tilt-adjuster [D] right or left until
the desired angle has been achieved.
Take note of the following when setting up the projector:
The projector table or stand should be level and sturdy.
Position the projector so that it is perpendicular to the screen.
Remove the Back Foot Holder on the rear adjuster foot before adjusting the projection
angle.
Ensure the cables are in a safe location. You could trip over them.
— 16 —
Loading...