Vivitek D8010W User Manual
User’s Manual
D8800 Series
Contents
COPYRIGHT INFORMATION 4
yCopyright 4
yDisclaimer 4
yAbout this manual 4
IMPORTANT SAFETY INSTRUCTIONS 5
yDisposal of old electrical and electronic equipment 6
yImportant Recycle Instructions: 6
INTRODUCTION 7
yAbout This Manual 7
yDescription, Features and Benefits 7
yParts List 8
CONTROLS AND FUNCTIONS 9
yD8800/D8900/D8010W at a Glance 9
yI/O Panel 10
yKEYPAD 11
yRemote control 12
yTo install batteries in the remote control 13
yRange of effective remote control signal reception 13
Installation Considerations 14
yAmbient Light 14
yThrow Distance 14
yModes of installation 15
yAllow at least 50 cm clearance around the exhaust vent. 16
Lens Shift 17
yVertical Lens Shift 17
yHorizontal Lens Shift 17
Connecting the projector to other devices. 18
yHDMI Connection 18
yTrigger connection 18
yIR Input connection 19
yS-VIDEO, VIDEO connection 19
yCOMPONENT connection 20
yRS-232 Connection 20
yLAN Connection 21
Start using the projector - Adjustments 22
yConnecting to AC Power 22
yTurning on the Power 22
yChanging the OSD Language 23
yAdjusting the Picture Orientation 23
yLens Adjustments 24
Start using the projector - Operation 25
ySelecting An Input Source 25
ySelecting an Aspect Ratio 25
yUsing the OSD 25
Start using the projector - OSD Introduction 26
yOSD Menu Tree 26
yOSD Introduction - INPUT 28
yOSD Introduction - PICTURE 31
yOSD Introduction - LAMPS 34
yOSD Introduction - ALIGNMENT 35
yOSD Introduction - CONTROL 39
yOSD Introduction - SERVICE 45
Change Lamp 47
yTo replace the projector lamp1 47
yTo replace the projector lamp2 48
Change Lens 49
yTo replace the projector Lens 49
Change Filter 51
yTo replace the Filter on the left side of the projector 51
yTo replace the Filter on the right side o f the projector 52
y Change the color wheel 53
LED Status 54
yPower LED 54
yStatus LED 54
yLamp1/Lamp2 LED 54
yTemp LED 54
yShutter LED 54
SPECIFICATIONS 55
SERIAL INTERFACE SPECIFICATIONS 56
yTransfer Specifications 56
yRS-232 Commands 56
yIR Codes and Key names 56
yOperations Commands 57
Dimensions 64
Supported Timings 65
Projection Distance and Screen Size 66
yOptional Lens
DLP Projector - User’s Manual
COPYRIGHT INFORMATION
Copyright
This publication, including all photographs, illustrations and software, is protected under international copyright laws,
with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without written consent of the manufacturer. The Vivitek logo is a trademark of “Vivitek Corporation.” © Copyright 2012
Disclaimer
The information in this document is subject to change without notice. The manufacturer makes no representations or
warranties with respect to the contents hereof and specifically disclaims any implied warranties of merchantability or
fitness for any particular purpose. The manufacturer reserves the right to revise this publication and to make changes
from time to time in the content here without obligation of the manufacturer to notify any person of such revision or
changes.
About this manual
This manual is intended for end users and describes how to install and operate the DLP projector. Wherever possible,
relevant information such as an illustration and its description has been kept on one page. This printer-friendly format is
both for your convenience and to help save paper, thereby protecting the environment. It is suggested that you only print
sections that are relevant to your needs.
4
DLP Projector - User’s Manual
IMPORTANT SAFETY INSTRUCTIONS
Thank you for your purchase of this quality product! For best performance, please read this manual carefully as it is your
guide through the menus and operation.
1. Read and Keep these instructions.
2. Heed all warnings.
3. Follow all instructions.
4. Do not use this apparatus near water. And not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that produce heat.
5. Clean only with a dry cloth.
6. Do not block any of the ventilation openings. Install in accordance with the manufacturer’s instructions.
7. Do not defeat the safety purpose of the polarized or grounding type plug. A polarized plug has two blades with
one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or
the third prong is provided for your safety. When the provided plug does not fit into your outlet, consult an electrician for the replacement of the obsolete outlet.
8. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles and the
point where they exit from the apparatus.
9. Only use the attachments/accessories specified by the manufacturer.
10. Use only with a cart, stand, tripod, bracket or table specified by the manufacturer or sold with the apparatus.
When a cart is used, use caution when moving the cart/apparatus to avoid injury from tip-over.
11. Unplug this apparatus during lightning storms or when unused for long periods of time.
12. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in
any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
13. The +12V trigger only outputs 12V DC signal for triggering. Do not connect to any other power input or output.
This could cause damage to this unit.
14. Keep the packing material in case the equipment should ever need to be shipped.
15. Never look into the lens when the projector is on.
AVOID EYE CONTACT TO THE LIGHT
5
DLP Projector - User’s Manual
Disposal of old electrical and electronic equipment
(Applicable throughout the European Union and other European countries with separate collection programs)
This symbol found on your product or on its packaging, indicates that this product should not
be treated as household waste when you wish to dispose of it. Instead, it should be handed
over to an applicable collection point for the recycling of electrical and electronic equipment. By
ensuring this product is disposed of correctly, you will help prevent potential negative consequences to the environment and human health, which could otherwise be caused by inappropriate disposal of this product. The recycling of materials will help to conserve natural resources.
This symbol is only valid in the European Union. If you wish to discard this product, please
contact your local authorities or dealer and ask for the correct method of disposal.
Important Recycle Instructions:
Lamp(s) inside this product contain mercury. This product may contain other electronic waste
that can be hazardous if not disposed of properly. Recycle or dispose in accordance with local,
state, or federal Laws. For more information, contact the Electronic Industries Alliance at WWW.
EIAE.ORG. For lamp specific disposal information check WWW.LAMPRECYCLE.ORG.
6
DLP Projector - User’s Manual
INTRODUCTION
About This Manual
This User’s Manual describes how to install, set up and operate the D8800/D8900/D8010W. Throughout this manual,
the Projector is referred to as the “D8800/D8900/D8010W.”
Target Audience Vivitek has prepared this manual to help installers and end users get the most out of the D8800/
D8900/D8010W. Vivitek has made every effort to ensure that this manual is accurate as of the date it was printed. However, because of ongoing product improvements and customer feedback, it may require updating from time to time. You
can always find the latest version of this and other Vivitek product manuals on-line, at www.vivitekcorp.com.
Description, Features and Benefits
The Vivitek D8800/D8900/D8010W provide state-of-the-art technology for full HD (1920 x 1200, WUXGA 16:10) native
resolution for crystal clear, pristine images. The D8800/D8900/D8010W offer incredibly high definition images at today’s highest avail-able resolutions. Equipped with precision optics, the D8800/D8900/D8010W include zoom, focus and
lens shift controls for a throw range of 1.85:1 to 2.40:1. For a smaller throw distance (1.56:1 to 1.86:1), the D8800/D8900/
D8010W can be fitted with a varying optics package (optional) to meet different requirements. Exceptional scaling and
film-to-video (3:2 pull-down) conversion is easily achieved. Combined with Vivitek’s sophisticated parameters for white
balancing, the D8800/D8900/D8010W’s proprietary de-interlacing technology provides the highest level of development for gray-scale and color balancing and artifact-free images. Completing this engineering marvel are discrete infrared (IR) and RS-232 control, power and source selection controls for seamless, flexible operation.
Key Features and Benefits
The D8800/D8900/D8010W offer these key features and benefits:
yNative Resolution: 1920 x 1080 (16:10 Native Aspect Ratio).
yDLP system using high-performance Digital Micromirror Device (DMD).
yHDMI 1.3 Input with High-bandwidth Digital Content Protection (HDCP).
yHDTV Compatible.
yExcellent Video Processing on progressive and interlaced video inputs.
Green Product with:
yLead free solder used for soldering including circuit and component electronics.
yLead free glasses and coatings.
yRecycled paper used in the user manuals and packing cartons.
yEnergy Saving: High efficiency power switching and less than 0.5W power consumption in standby mode.
7
DLP Projector - User’s Manual
Additional Features of the D8800/D8900/D8010W
yHorizontal and vertical lens shift.
yKeystone adjustment.
Parts List
Your D8800/D8900/D8010W is shipped with the following items, if any items are missing or damaged, please contact
your dealer or Vivitek Customer Service.
Accessory Box List D8800/D8900/D8010W
Item Manual Assy Q’ty EU/ASIA/US/TWN China
1
CD-ROM 1
2
WARRANTY CARD (US/EUR) 1
3
WARRANTY CARD (CN) 1 -
4
RoHS Card (CN) 1 -
5
QC Pass Card (CN) 1 -
6
Important Information (CN) 1
7
POWER CORD 125Vac USA 1
8
POWER CORD 250Vac EUR 1
9
POWER CORD 250Vac CHINA 1 -
10
VGA Signal cable 1
11
SCREW M M4*0.7*70 PAN C SUS 1
12
BATTERY 2
13
REMOTE 1
14
MODULE COLOR TYPE COLOR WHEEL 1
● ●
●
● ●
●
●
● ●
● ●
● ●
● ●
● ●
-
●
●
●
-
-
●
8
CONTROLS AND FUNCTIONS
D8800/D8900/D8010W at a Glance
Adjustable
feet*4
Rear Infre-red window
(remote control)
Air inlet
Power inlet
Power switch
DLP Projector - User’s Manual
yAir outlet
Warm air exits the projector through this vent. Ensure
that it is not blocked.
yAir inlet
Internal fans draw cool air into the projector through
this vent.
yAdjustable feet
Use these when the projector is installed in a tabletop configuration to level the image and/or adjust the
projection angle.
yPower Inlet
For input power from wall outlet to projector.
Air outlet
yRear Infre-red window
For receive the remote controller’s message.
Air inlet
Air outlet
Air outlet
9
DLP Projector - User’s Manual
I/O Panel
IN SDI OUT
LAN
HDMI
DVI-D
RGB
B/Pb G/YR/Pr
VH
WIRED REMOTE TRIGGER
ySDI
Connect a BNC cable from a serial digital interface (SDI) device.
yHDMI
Connect an HDMI source.
yDVI
Connect a DVI source.
yComponent
Connect a Component (YUV HS/VS-CS) source.
yWIRED REMOTE
Wired input from a Niles- or Xantech-compatible, infrared (IR) repeater system.
S-VIEDOVIEDO
RS-232
yTRIGGER
(3.5-mm, mini phone jack) Offers 12 (+/- 1.5) V of output for 350mA monitor relay with short circuit protection.
yS-VIDEO
A standard S-Video input for connecting a DVD player, satellite receiver or Super VHS (S-VHS) VCR.
yVIDEO
Standard composite video input for connecting a VCR, laser disc player or other composite video source. Also provides composite sync input for RGBS sources.
yLAN
Connect an RJ45 ethernet cable.
yRGB
Provides a standard, 15-pin VGA-style connection to either an RGB or component high-definition source, or to a
personal computer.
The D8800/D8900/D8010W automatically detect the input signal resolution.
yRS-232
9-pin D-sub connector for interfacing with a PC or home theater automation/control system.
10
KEYPAD
POWER INPUT AUTO SYNC ASPECT OPEN CLOSE
SHUTTER
DLP Projector - User’s Manual
LENS
SHIFT
MENU EXIT
FOCUS ZOOM
yPOWER
Use the button to turn on/off the projector.
yINPUT
Press to select a video source. HDMI, DVI, VGA, Component / BNC Composite, S-Video or 3D-SGI.
Press this to re-acquire the current active source.
yASPECT
Press this to change the aspect ratio of the current image.
ySHUTTER
Use the buttons to turn on/off shutter.
yMENU
Press this button to show or hide the OSD menu.
yENTER, , , ,
Use these buttons to select items or settings, adjust settings or switch display patterns.
yEXIT
Press this to go one menu higher or exit the OSD menu.
yLENS SHIFT
Button to shift control of the lens, up/down or left/right.
yFOCUS
Button to focus the projected image.
yZOOM
Button to zoom in/out the lens.
11
DLP Projector - User’s Manual
123
456
Remote control
ON
FOCUS ZOOM
MENU EXIT
INPUTPICTURE NETWORK
AUTO SYNC
OVERSCAN
7809
CLEAR SHUTTERID SET
POWER
ENTER
ASPECTPIP
FREEZE
INFO.LIGHT
OFF
TEST
PATTERN
LENS SHIFT
LAMP MODE
y ON
Use this button to turn the projector on.
y OFF
Use this button to turn the projector off.
y FOCUS
Focuses the projected images.
y ZOOM
Zoom in/out the projected image.
y TEST PATTERN
Use this to enter test pattern menu.
y LENS SHIFT
Button to shift control of the lens, up/down or left/right.
y ENTER, , , ,
Use these buttons to select items or settings, adjust settings or switch
display patterns. ENTER: Press to select a highlighted menu item or confirm
a changed setting.
y MENU
Press this button to show or hide the OSD menu.
y EXIT
Press this to go one menu higher or exit the OSD menu.
y INPUT
Press to select a input source.
y PICTURE
Starts the PICTURE function.
y NETWORK
Press this to enter the Network (LAN) menu.
y AUTO SYNC
Press this to re-acquire the current active source.
y ASPECT
Selection Button: Press this button repeatedly to select one of the following
aspect ratios: 16 : 9: For viewing 16:9 DVDs or HDTV programs in their native
aspect ratio.
y PIP
Press this to display the picture-in-picture screen.
y OVERSCAN
Press to select an overscan mode.
y FREEZE
Freeze/unfreezes the on-screen picture.
y LAMP MODE
Press this to select a higher or lower brightness setting.
y INFO.
Starts the SERVICE function.
y LIGHT
Press this to turn on remote control backlight.
y CLEAR
Not available
y SHUTTER
Use the button to turn on/off shutter.
y ID SET
Not available
Notes on Remote Control Operation
y In most situations, you can simply point the remote control at the screen which will reflect the IR signal from the re-mote back
toward the IR receiver on the projector. In some cases, however, ambient conditions may prevent this. If so, point the remote
control at the projector and try again.
y If the effective range of the remote control decreases, or it stops working, replace the batteries with new ones.
y The remote control may fail to operate if the infrared remote sensor is exposed to bright sunlight or fluorescent lighting.
12
To install batteries in the remote control
STEP 1 STEP 2 STEP 3
1. Slide the battery compartment cover in the direction of the arrow to remove it.
2. Install two AA batteries with the correct polarity.
3. Replace the cover.
Notes on Batteries
y Make sure that the battery polarities are correct when installing the batteries.
y Do not mix an old battery with a new one or different types of batteries.
y If you will not use the remote control for a long time, remove the batteries to avoid damage from battery leakage.
DLP Projector - User’s Manual
Range of effective remote control signal reception
10m
30°
IR Reception eective Angles: 30°
IR Reception eective distance: 10m
Note:
Avoid placing the remote control at places of high temperature or humidity as it could cause the remote control to malfunction.
13
DLP Projector - User’s Manual
Installation Considerations
Proper installation of your projector will ensure the quality of your display. Whether you are installing a projector temporarily or permanently, you should take the following into account to ensure your projector performs
optimally.
Ambient Light
In general, minimize or eliminate light sources directed at the screen. Contrast ratio in your images will be noticeably
reduced if light directly strikes the screen, such as when a shaft of light from a window or floodlight falls on the image.
Images may then appear washed out and less vibrant.
Requires separate room Installation cost is usually higher.
Throw Distance
Throw distance is the distance measured from the front of the projector to the screen. This is an important calculation in
any projector installation as it determines whether or not you have enough room to install your projector with a de-sired
screen size and if your image will be the right size for your screen. You can quickly estimate the throw distance by taking
the width of the screen and multiplying it by the lens throw ratio; see the image as following. The result of this calculation tells you roughly how far back the projector should be positioned from the screen in order to project a focused image large enough to fill the screen.
Throw Distance (TD) = Screen Width (W) x Throw Ratio (TR)
Screen Width (W)
Throw Distance (TD)
Two models of the D8800/D8900/D8010W are available, one with 1.56-1.86:1 lens and the other with 1.85-2.40:1 lens
With optional zoom adaptors throw ratios of 1.24 – 3.0 can be achieved. The standard D8800/D8900/D8010W offer
throw ratios between 1.85:1 and 2.40:1. With the optional, short-throw lens, the D8800/D8900/D8010W offer throw
ratios between 1.56:1 and 1.86:1.
14
Modes of installation
Frontal projection - desktop installation
Advantages: easy to install can be easily moved or adjusted
easy to operate.
DLP Projector - User’s Manual
Disadvantage: occupies floor space and limits seating
capacity.
Rear projection - desktop installation
Advantage: the projector is completely hidden from plain
view the projector can be easily operated this
setup usually offers better reduction of ambient noise.
Disadvantage: requires an additional room for installation
relatively higher costs for installation.
Frontal projection - ceiling mode
Advantage: does not occupy floor space does not draw
attention to it. Eliminates the possibility that
someone would accidentally move the projector.
Disadvantage: stricter installation requirements and
conditions; care should be taken during
the installation to ensure the projector has
been securely mounted. Operation of the
projector becomes inconvenient without the
remote control.
Projector
Projector
Projector
Rear projection - ceiling mode
Advantage: the projector is completely hidden from plain
view this setup usually offers better reduction
of ambient noise.
Disadvantage: requires an additional room for installa-
tion. Stricter installation requirements and
conditions; care should be taken during
the installation to ensure the projector has
been securely mounted. Operation of the
projector becomes inconvenient without the
remote control.
Projector
15
DLP Projector - User’s Manual
Allow at least 50 cm clearance around the exhaust vent.
The device need to have enough space to prevent issues as stated in this image.
Side Way
Back Side
Celling Mount
50cm
Or Greater
70cm
Or Greater
30cm
Or Greater
50cm
Or Greater
16
DLP Projector - User’s Manual
Lens Shift
Vertical Lens Shift
The D8800/D8900/D8010W have a lens shift capability which allows the vertical movement of the image without moving the projector. Lens shift is generally expressed as a percentage of the screen height. For ceiling mounted projectors,
the lens can be moved 50% (0.5V) downward, while the lens can be moved 50% (0.5V) up or down on a desktop mounted
projector.
Ceiling Front Projection
Max.
Vertical Shift
0.5V
Desktop Front Projection
Height of projected image
Max.
0.5V
1V
Vertical Shift
Max.
0.5V
1V
Note:
This is a general example of lens shift. Lenses vary in their shift capabilities. No particular lens or projector is used in this example.
Horizontal Lens Shift
The D8800/D8900/D8010W have a lens shift capability which allows the horizontal movement of the image without
moving the projector. The lens can be moved 10% (0.1H) to the right or left within the housing.
Max.
0.5V
1V
Normal Projection Position
0.1H
Shift to Left Shift to Right
Width of projected image
0.1H1H
Note::
This is a general example of lens shift. Lenses vary in their shift capabilities. No particular lens or projector is used in this example.
17
DLP Projector - User’s Manual
Connecting the projector to other devices.
Proceed as follows to connect the D8800/D8900/D8010W to your video sources, external controller(s) - if present - and
AC power. When connecting your equipment: •Use the correct signal cables for each source. •Ensure that the cables are
securely connected. Tighten the thumbscrews on connectors that have them. Connecting Source Components to the
D8800/D8900/D8010W Connect your video sources to the D8800/D8900/D8010W as shown and described in the sections that follow.
HDMI Connection
IN SDI OUT
LAN
HDMI
DVI-D
RGB
B/Pb G/YR/Pr
VH
WIRED REMOTE TRIGGER
RS-232
S-VIEDOVIEDO
DVI Source(s)
(BD/HD-DVD/DVD Player, HD SetTop Box, Game Console etc.)
Trigger connection
If your home theatre system includes a projector screen, screen cover or other 12V Trigger equipment, please connect
such device/equipment to the projector’s 12V Trigger output as illustrated. After you have done so, your screen will lower
automatically whenever you turn on your projector for your convenience.
Retractable screen or other
12V device
Sleeve = Ground
Tip = +12V
B/Pb G/YR/Pr
WIRED REMOTE TRIGGER
S-VIEDOVIEDO
Projector Screen
VH
18
RS-232
DLP Projector - User’s Manual
IR Input connection
If infrared signals from the remote control cannot reach the projector due to excessive distance or obstructions such as
walls or cabinet doors, you can connect an external IR repeater system to the IR INPUT on the D8800/D8900/D8010W to
extend the range of the remote control.
IR repeater
Remote control
IR sensor
B/Pb G/YR/Pr
VH
WIRED REMOTE TRIGGER
RS-232
S-VIEDOVIEDO
S-VIDEO, VIDEO connection
If the image input device offers both S-Video and Video connection, it is recommended that you choose S-Video to obtain
better image quality. If both the S-Video and Video inputs are connected to the projector, the projector will prioritize SVideo signal input and image from the Video input will not be played.
IN SDI OUT
LAN
HDMI
DVI-D
RGB
B/Pb G/YR/Pr
VH
WIRED REMOTE TRIGGER
RS-232
S-VIEDOVIEDO
DVD player, VCR, satellite receiver,
LD and so forth
19
DLP Projector - User’s Manual
COMPONENT connection
Take the 3/5 cabled RGB component video connectors from the source equipment to the projector’s COMPONENT jacks.
Y PbPr
IN SDI OUT
LAN
HDMI
DVI-D
RGB
B/Pb G/YR/Pr
VH
WIRED REMOTE TRIGGER
RS-232
S-VIEDOVIEDO
DTV set-top-box or other component (YPbPr) input source
RS-232 Connection
Connect a PC or home theater control/automation system (if present) to the RS-232 port on the D8800/D8900/D8010W.
Use a standard, 9-pin serial cable, wired straight-through.
HDMI
IN SDI OUT
LAN
DVI-D
RGB
Desk Top or Notebook
RS-232 Interface and Requirements
The RS-232 Commands use only ASCII characters which can be entered using a typical terminal emulator like Windows
HyperTerminal with the following setting:
Bits per second: 38400
Data bits: 8
Stop bits: 1
Flow control: None
Parity: None
20
LAN Connection
DLP Projector - User’s Manual
Desk Top or Notebook
Network Swtich
IN SDI OUT
LAN
HDMI
DVI-D
RGB
21
Loading...