Vitek VTD-HOCRAZ922 Quick Start Guide

Optional Dome Mounts to Suit any Application!

Package Includes

HD-SDI Dome Camera

Complete Installation and
Operation Instructions on CD

Plastic Anchor:

6 x 30mm (4pcs)

Mounting Screw:
4 x 30mm (4pcs)

General Operation
Instructions

Video Sub-Out Cable (1pc)

Torque Wrench: 3mm (1pc)

Mounting Template

VTC-HOCRAZ39/922

2.1MP HD-SDI Compact Indoor/Outdoor
WDR True Day/Night Dome Camera

VITEK

FEATURES:

• 1/2.9” Sony® CMOS

• 2.1 MegaPixel With full 1080p/720p HD-SDI Output
(SMPTE 292M)

• MegaPixel IR Corrected 3-9mm (VTC-HOCRAZ39)
/9-22mm (VTC-HOCRAZ922) Varifocal Lens

• Mechanical IR Cut Filter (True Day/Night)

• 16:9 Video format

• On-board Intelligence (OBI Technology) delivers Auto­Focus-Zoom by tracking motion, then optically zooming in
to that area of the frame

• Fully programmable advanced WDR

• Two (2) High Power 850nm IR LEDs with up to 80’ foot
range

• Integrated Cooling Fan

• Advanced OSD Functions: Motion Activated Pointing
Zoom, Defog, Dynamic IR, BLC/HLC, Motion Deblur, Pixel
Defect Compensation, Title Set, Mirror, Flip

• 100% Pure Digital Transmission of video data

• Up to 700’ HD Transmission Range (Depending on cable
characteristics and integrity)

• Heavy Duty IP68 rated weather/
vandal resistant aluminum construction

• 12VDC / 24VAC Dual Voltage
Operation

2

Safety Precaution

To prevent fire or shock hazard, do not expose the unit to rain or moisture.
To prevent electric shocks and risk of fire hazards, do NOT use other than
specific power source.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The symbol is intended to alert the user to the presence of uninsulated
"dangerous voltage" within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons .

Safety Precaution

NOTICE

The image used in this instruction manual are processed to help comprehension
and may differ from actual video of the camera.

Avoid installing in areas where shock or vibration may occur.

Pay attention to safety when installing the connection cable and observe that the
cable is not subjected to heavy loads, kinks or damage and no moisture can get in.

Never open the device such as boards or lens.
The warranty becomes void if repairs are undertaken by unauthorized persons.
Maintenance and repair have to be carried out only by authorized service centers.
Use only a mild detergent to clean the housing.
The camera should never be operated beyond the technical specifications.
This can lead to damage to the camera and void the warranty.
The camera should never be operated in water.

The symbol is intended to alert the user to the presence of important
operating and maintenance(servicing) instructions in the literature
accompanying the unit.

Warning :

This equipment has been tested and found to comply with the limits for a Class

A digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment . This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
his own expense.

Caution :
Any changes or modifications in construction of this device which are not expressly
approved by the party responsible for compliance could void the user’s authority
to operate the equipment.
Mains power quality should be that of a typical commercial environment. If the user
of the model requires continued operation during power mains interruptions, it is
recommended that the model be powered from an uninterruptible power supply
(UPS) or a battery.

3 4

Complete Installation and Operation Instructions can be
found on Included CD.

Installation Instructions

Installation Instructions

1. Locate the mounting template at the installation position and drill the ceiling
or wall if needed.

2. Open the dome cover by loosening screws(4x12mm). Use the torque wrench
supplied.

A. Flush mount type:

- Place the dome base unit on pre-drilled position and attach using mounting
screws (4x30mm).

- Route the Power cable to the connecting place.

B. Surface mount type (Option):

- Place the surface mount on pre-drilled position and attach using mounting
screws (4x30mm). Assemble the cable conduit, otherwise tighten a conduit hole
cap.

- Route the Power cable to the connecting place.

- Affix the dome base unit to the surface mount using the assembly screws
(4x14mm). Before attaching the dome base make sure the assembly holes are
aligned with the surface mount assembly holes.

4. Set the cameras viewing angle.

5. Replace the dome cover to the dome base unit and tighten the assembly screws.

Flush mount type

A

Flush Mount Installation
requires a Flush Mount
Decorator Plate
(See pg. 3)

See Optional Dome Mounts (pg. 3)

Assembly Screw

(4x12mm)

3

See Optional Dome Mounts (pg. 3)

Surface mount type

B

Flush Mount
Decorator Plate

Mounting Screw

(4x30mm)

Assembly Screw

(4x14mm)

Limit of pan & tilt

1) Pan limit:
Pan is limited to +/- 165°. Do NOT force the gimbal over the limit, this will
prevent internal damage.

2) Tilt limit:
Tilt is limited to 15° min ~ 90° max. with reference to the ceiling when the
inclination of camera module is 0°, that is, the image is aligned horizontally.

3) Inclination limit (Horizontal image alignment):
Inclination limited to +/-60° max.

.

15…

90…

CAUTION

• Extreme care should be taken NOT to scratch the bubble dome surface while

installing or adjusting the camera.

• Care should be taken that the cable is NOT damaged, kinked or exposed in

a hazardous area.

• Tighten the dome cover mounting screws so that there is NO gap between Lens

hood and clear bubble to avoid IR reflection

.

Torque Wrench

5

Installation Instructions

Power Supply Connections

Make sure the power is removed before installation.
Camera can work with either 24VAC or 12VDC, dual voltage power.
Primary and secondary grounds are completely isolated to avoid the possible
ground-loop problems.

In case that HD-SDI Inputs are not supported by Monitor, please use HD-S DI
Converter to connect HD-SDI cable with Monitor

Some computer monitors or TVs may not support 30p/25p.
Please check Specification of Monitor before installation.

.

6

LIMITED LIABILITY WARRANTY

VITEK products carry a three (3) year limited warranty. VITEK

warrants to the purchaser that products manufactured by VITEK

are free of any rightful claim of infringement or the like, and when

used in the manner intended, will be free of defects in materials and

workmanship for a period of three (3) years, or as otherwise stated

above, from the date of purchase by the end user. This warranty is

nontransferable and extends only to the original buyer or end user

customer of a VITEK Authorized Reseller.

The product must have been used only for its intended purpose, and

not been subjected to damage by misuse, willful or accidental damage,

caused by excessive voltage or lightning.

0.2M

VIDEO (BNC)

AC24V/DC12V (Red wire)

AC24V/GND (Black wire)

RTX+ (White wire)

RTX- (Gray wire)

The product must not have been tampered with in any way or the

guarantee will be considered null and void.

This guarantee does not affect your statutory rights.

Contact your local VITEK Reseller should servicing become

necessary.

VITEK makes no warranty or guarantee whatsoever with respect to

products sold or purchased through unauthorized sales channels.

Warranty support is available only if product is purchased through a

VITEK Authorized Reseller.

28492 CONSTELLATION ROAD
VALENCIA, CA 91355
WWW.VITEKCCTV.COM

Version 1.1

Sept 2014

7 8