Vitek VTD-HOCMD2CH User Manual

VTD-HOCMD2CH

HD-SDI Vandal Resistant

Mini Dome 2.1 Megapixel

VITEK

FEATURES:

• 1/3” 2.1Megapixel CMOS Sensor

•1080(1920x1080)@30fps

• 3.6mm Fixed Lens Included

• 2D-DNR - Two Dimensional Motion Adaptive Noise
Reduction

• Can be Semi-Flush or Surface Mounted

• IP-66 Rated Weather Resistant Aluminum Enclosure w/
Polished Chrome Finish

• 12VDC Operation

INSTALLATION

Open

1) Align the camera unit with the
surface of the ceiling, make marks
on the ceiling in the places where
the screw holes are to be drilled,
and then drill the three holes.

2) Cut a hole (diameter:50mm) in the
ceiling for routing the cables.

3) Pass the power cable (B) and video
cable (A) from the camera unit
through the cable hole in the ceiling.

4) Align the three screw holes in the
camera unit (C) with the screw holes
in the ceiling, and then secure the
camera in place by tightening the
three tapping screws.

Close

5) Use the supplied four screws (E) to
secure the middle base (D) to the
bottom base (C)

6) Tighten the guide ring (G), then
adjustment the camera (F).

7) Attach the bubble (H) to the middle
base (D).

8) Attach the top cover (I) to the middle
base (D).

9) Use the supplied star-shaded
L-wrench to tighten the set screw on
the top cover.

1

SPECIFICATIONS

SPECIFICATIONS VT-HOCMD2CH

Image Device

Resolution

Effective Pixels

Minimum Illumination

Included Lens

Day/Night

Noise Reduction

Synchronization

S/N Ratio

Video Output

Electronic Iris

Construction

Water Resistance

Power Source

Power Consumption

Operating condition

Dimensions

1/3” 2.1Megapixel CMOS

1920x1080p(1080p/30fps)

1944(H)x1092(V) (2,122,848 Pixels)

0.1LuX / F2.0

3.6mm Fixed Megapixel lens

Auto

2D-DNR

Internal

More than 50dB

VBS 1Vpp +/-10%, 75ohm

1/60 ~ 1/100,000sec

Aluminum Housing with Polished Chrome Finish

IP-66

12VDC

150mA

14F ~ 122F (-10C ~ +50C) / 95% RH Max

3.15” x 1.69”/2.47” (80mm x 42.8mm/62.8mm)

Weight

14.11 Oz. (400g)

2

LIMITED LIABILITY WARRANTY

VITEK products carry a three (3) year limited warranty. VITEK warrants
to the purchaser that products manufactured by VITEK are free of any
rightful claim of infringement or the like, and when used in the manner
intended, will be free of defects in materials and workmanship for a
period of three (3) years, or as otherwise stated above, from the date of
purchase by the end user. This warranty is nontransferable and extends
only to the original buyer or end user customer of a Vitek Authorized
Reseller.

The product must have been used only for its intended purpose, and
not been subjected to damage by misuse, wilful or accidental damage,
caused by excessive voltage or lightning.

The product must not have been tampered with in any way or the
guarantee will be considered null and void.

This guarantee does not affect your statutory rights.

Contact your local VITEK Reseller should servicing become necessary.

VITEK makes no warranty or guarantee whatsoever with respect to
products sold or purchased through unauthorized sales channels.
Warranty support is available only if product is purchased through a
VITEK Authorized Reseller.

28492 Constellation Road ValenCia, Ca 91355

WWW.ViteKCCtV.CoM

Version 1.0

Sept 2014