VTD-C13A
Alpha Series Indoor Color
Dome Camera
VITEK
• 1/3” Color CCD image sensor w/420 TV Lines
• Minimun Illumination of 0.5 Lux / F2.0
• 3.6mm / f2.0 Standard Lens
• 12VDC Operation
CAUTION
RISK OF ELECTRICAL SHOCK
DO NOT OPEN
1. Unit contains uninsulated dangerous
voltage within the enclosure that
may be of sufficient magnitude to
constitute a risk of electric shock to
persons
2. Only use DC Power Supply
3. Read & Keep these instructions.
4. Heed to all warnings and follow all
instructions carefully.
5. Do not use near water.
6. Clean only with dry cloth.
7. Do not block any ventilation
openings. install in accordance with
the instructions.
8. Do not install near any heat source
such as radiators, heat resisters,
stoves, or other apparatus (including
amplifiers) that produce heat.
9. Do not defeat the safety purpose of
the polarized or grounding-type plug.
A polarized plug has to blades with
one wider the other. A grounding
type plug has to blades and a third
grounding plug. The wide blade
or the third prong are provided for
safety. if the provided plug dose not
fit into your into your outlet, consult
an electrician for replacement of the
obsolete outlet.
10. Protect the power cord from being
walked on a pinched particularly at
plugs, convenience receptacle, and
the point where they exit from the
apparatus.
11. Only use attachment/accessories
specified by VITEK.
12. Use only with cart, stand, tripod,
bracket, or table specified by the
manufacturer, or sold with the Unit,
13. Unplug this unit during lightning
storms or when unused for long
periods of time.
14. Refer all servicing to qualified service
personnel, Servicing is required
when the unit has been damaged in
any way, such as power-supply cord
or plug is damaged, liquid has been
spilled or objects have fallen into the
unit, the unit has been exposed to
rain or moisture, does not operate
normally or has been dropped.
15. Do not attempt to service this
product yourself as opening or
removing covers may expose you to
dangerous voltage or other hazards.
Refer all servicing to qualified service
personal.
CAUTION - To reduce the risk of electric
shock, do not perform any servicing
other than contained in these operating
instructions unless you are qualified to
do so.
2
INSTALLATION
1. Turn “Dome Cover” (as shown in Figure 1) counterclockwise to the end and take it off.
2. Mark the positions of one “power and video line hole” and four “screw holes” on the
ceiling. (as shown in Figure 2 & Figure 3).
Drill a hole on the proper position of the ceiling for the power and video line to pass through.
And then screw “base” to the ceiling.
Note: Screws for installation are not supplied within the sales package. Please prepare by
yourself and use proper screws.
Suggestions:
a) For safety, please let the power and video line concealed behind the ceiling.
b) If the installation spot doesn’t allow the installation personnel to screw power and video
line hole on the ceiling, they could cut the concave edge of “base” to let the power and video
line pass through.
3. Adjust the view angle of the lens (as shown in Figure 3). Then put “dome cover” back to
the “base” and turn clockwise.
Figure 1 - Dome
Cover
Figure 2 Figure 3 - 4
Screw Holes
Figure 4 - Power
& Video Line
Hole
CONNECTION
1. DC12V Input Terminal
Connect the power terminal of the camera to a 12V DC regulated power supply.
Note: Please use the correct power adaptor, DC12V (regulated), to operate this unit. The
power tolerance of this unit is DC12V ± 10%. O¬¬ver maximum DC 12V power input will
damage this unit.
2. Video Output Connector (VIDEO OUT)
Connect the camera video output and the monitor video input with 75Ω coaxial
cable.
3
SPECIFICATIONS
Image Sensor
Effective Pixels
Resolution
Minimum illumination
S/N Ratio
Electronic Shutter
Lens
Lens Angle
IRIS Mode
Gain Control
White Balance
Video Output
Power Source
Current Consumption
Dimensions
1/3” Interline transfer type color CCD
512(H) x 492(V)
420 TVL
0.5 Lux / F2.0
More than 48dB (AGC off)
1/60 (1/50) to 1/100,000 sec.
f3.6mm / F2.0
70 Degrees
AES
Auto
ATW
1.0Vp-p composite, 75 Ohms
12VDC
100mA
Diameter x Height: 3.94” x 2.36” (100mm x 60mm)
4
VTD-C13A Inside
OTHER GREAT PRODUCTS BY
VT-H Series
4, 8, and 16 Channel Digital Video
Recorders with H.264 Compression
The Alpha Series VT-H Series Digital Recorders combine the latest H.264 Compression
technology with stability and simple operation. H.264 Compression is the next generation
of MPEG4 allowing up to 50% smaller file sizes for increased storage capability and/or
resolution as well as a more fluid internet transmission speed. VT-H Series DVRs can be
controlled via supplied IR Remote control or remote client.
• 4, 8, or 16 Video Inputs with 1 BNC & 1 VGA Output
• H.264 Compression
• Supports both Dynamic and Static IP Addresses
• Up to 120 IPS Recording / Live Display
• Remote Viewing over the Internet or LAN
• Supports one internal SATA Hard Drive
• 250GB to 1TB Internal Storage Options
• Quadplex operation enabling simultaneous recording, playback,
networking, and backup
• 4 Audio Inputs & 1 Output
• Control locally via Included IR Remote control
• Backup via Ethernet or USB
5
H.264
Compression
VTM-LCDP Series
15”, 17“, and 19” Professional LCD
Monitors with Looping BNC Inputs
• 15”, 17“, and 19” Professional LCD Display
Panels
• Designed for continuous 24/7 operation
• VGA, Looping BNC Composite, and S-Video
Video Inputs. DVI & HDMI Inputs on 17“ & 19”
Versions
• Resolution up to 1280 X 1024 (17” & 19”)
• Stereo Audio Input/Output
• VESA Standard Mounting
VTC-IRLED24 Series
Color Bullet Cameras with 24 IR LED
Illumination
• 1/3” Color CCD image sensor
• 520 TV Lines of Resolution (VTCIRLED24H) /
420 TVL (VTC-IRLED24A)
• Minimun Illumination of 0.6 Lux (0 Lux / F2.0
with IR LEDs On)
• 24 IR LEDs with 50’ Range
• 3.6mm / f2.0 Standard Lens
• Automatic IR triggers On under low illumination /
Off under Normal Illumination
• Sun Shroud to reduce glare and dissipate heat
• 12VDC Operation
6
NOTES
7
VITEK LIMITED PRODUCT WARRANTY
VITEK products carry a three (3) year limited warranty. Digital recording and storage products are also warranted for 3 years except for the
hard drives which carry their own independent factory warranty from the
hard drive manufacturer. VITEK warrants to the purchaser that products
manufactured by VITEK are free of any rightful claim of infringement or
the like, and when used in the manner intended, will be free of defects in
materials and workmanship for a period of three (3) years, or as otherwise stated above, from the date of purchase by the end user. This
warranty is non-transferable and extends only to the original buyer or end
user customer of a Vitek Authorized Reseller.
The product must have been used only for its intended purpose, and
not been subjected to damage by misuse, willful or accidental damage,
caused by excessive voltage or lightning.
The product must not have been tampered with in any way then the
guarantee will be considered null and void.
This guarantee does not affect your statutory rights.
Contact your local VITEK Reseller should servicing become necessary.
Vitek makes no warranty or guarantee whatsoever with respect to
products sold or purchased through unauthorized sales channels.
Warranty support is available only if product is purchased through a
Vitek Authorized Reseller.
28492 Constellation Road ValenCia, Ca 91355
WWW.ViteKCCtV.CoM | 888-ViteK-70
8
Loading...