Page 1
VITEK
FEATURES
• 1/2.5” 5.0 Megapixel Progressive Scan CMOS
Sensor
• High Definition Analog (HDA): HD-TVI & AHD: 5.0
MegaPixel / CVI: 4.0 MegaPixel / CVBS: 960H
Video Output
• 3.3-12mm Varifocal Lens
• Infrared LED’s with up to 120’ IR Range
• Digital Wide Dynamic Range (D-WDR)
• True Mechanical Day/Night function by ICR
VTC-THB5RV
VTD-THD5RV
Transcendent 5.0 Megapixel Indoor/
Outdoor 4-IN-1 HDA Varifocal Bullet
Camera w/IR LED Illumination &
Varifocal Lens
• 2D-DNR Noise Reduction
• IP66 Weather Resistance
• Supports Up The COAX Control
• Over 1500’ HD Video Transmission (Depending on
cable characteristics and integrity)
• Optional Mounts Available
• 12VDC Operation
• 3 Year Warranty
Page 2
Safety Precaution
To prevent electrical shock and risk of fire hazards, do not expose this unit
to rain or moisture and only use specified power source..
CAUTION: TO REDUCE THE RISK OF ELECTICAL
SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL
The symbol is intended to alert the user to the presence of uninsulated
"dangerous voltage" within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electrical shock.
The symbol is intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the literature
accompanying the unit.
Warning :
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
their own expense.
Caution :
Any changes or modifications in construction of this device which are not expressly
approved by the party responsible for compliance could void the user's authority
to operate the equipment.
Main power quality should be that of a typical commercial environment. If the user
of the model requires continued operation during power interruptions, it is
recommended that the device be powered from an uninterruptible power supply
(UPS).
Limited Product Warranty
VITEK products carry a three (3) year limited warranty. VITEK warrants to
the purchaser that products manufactured by VITEK are free of any rightful
claim of infringement or the like, and when used in the manner intended,
will be free of defects in materials and workmanship for a period of three
(3) years, or as otherwise stated above, from the date of purchase by the
end user. This warranty is nontransferable and extends only to the original
buyer or end user customer of a VITEK Authorized Reseller.
The product must have been used only for its intended purpose, and not
been subjected to damage by misuse, willful or accidental damage, caused
by excessive voltage or lightning.
The product must not have been tampered with in any way or the
guarantee will be considered null and void.
This guarantee does not affect your statutory rights.
Contact your local VITEK Reseller should servicing become necessary.
VITEK makes no warranty or guarantee whatsoever with respect to
products sold or purchased through unauthorized sales channels. Warranty
support is available only if product is purchased through a VITEK
Authorized Reseller.
2
Page 3
VTC-THB5RV Components
Camera
User Manual
Screws
Drill Template
Video Connection
Connect the BNC video connector to a BNC cable, then to a DVR.
Monitor
Overview
1
8
1
2
3
4
5
2
Lens
Sun Shield
Mount Lock
Mount Base
BNC Video Output
Video
Video Output Mode Switch:
Select the desired video mode using the dip switches contained
3 4
9
10
6
7
8
9
10
5
Output Mode Switch
Power Cable
Lens Cover
Zoom
Focus
76
within the on-cable Output Mode Switch as follows:
ON
ON
1
2
Power Connection
Connect the power connector to a regulated 12 VDC power adaptor.
ON
1
1
2
2
AHD
HD-TVI
ON
ON
1
1
2
2
CVBS
CVI
12VDC
Power
3
Page 4
Installation
Before you begin, please make sure that the wall or ceiling is strong
enough to withstand 3 times the weight of the camera. The mounting
steps are as follows:
1. Attach the drill template to
the place where you want to
install the camera, then drill
3 screw holes and 1 cable
hole (if you want to route the
cables through the mounting
base) according to the drill
template
2. Route the cables and connect the power & video cables, then
secure the mounting base to the ceiling or wall with screws.
Ceiling Mounted
Wall Mounted
3. Loosen the mount lock to adjust the Pan and Tilt of the camera, then
tighten the mount lock to secure the viewing angle adjustments.
360° Pan
90° Tilt
4. To adjust the lens, start by removing the Lens Cover, then adjust
the Focus and Zoom levers to achieve a clear image. Replace
the Lens Cover. (if your camera is Fixed lens, please skip this
step)
Lens Cover
Zoom
Focus
5. Carefully remove the protective film from the lens
to complete the installation.
4
Page 5
VTD-THD5RV Components
Camera
Manual
Drill Template
Screws
Hex Wrench
Video Connection
Connect the BNC video connector to a BNC cable, then to a DVR.
Monitor
Overview
2
1
1
2
3
4
5
Dome Cover
Lens
BNC Video Output
Output Mode Switch
Power Cable
6
7
8
9
Focus
Zoom
Lock Screw
Mounting Base
3
4
5
6
7
Video Output Mode Switch:
Select the desired video mode using the dip switches contained
within the on-cable Output Mode Switch as follows:
ON
1
2
8
Power Connection
9
Connect the power connector to a regulated 12 VDC power adaptor.
Video
ON
ON
1
1
2
2
AHD
HD-TVI
ON
ON
1
1
2
2
CVBS
CVI
12VDC
Power
5
Page 6
Installation
Before you begin, please make sure that the wall or ceiling is strong
enough to withstand 3 times the weight of the camera. The mounting
steps are as follows:
1. Loosen the screws
to open the lower
dome and then
loosen the lock
screw to remove the
mounting base.
Lock Screw
4. Install the camera to the mounting base with the lock screw.
2. Attach the drill template to
the place where you want to
install the camera, then drill
4 screw holes and 1 cable
hole (if you want to route the
cables through the mounting
base) according to the drill
template.
3. Route the cables and
connect the power & video
cables, then secure the
mounting base to the ceiling
or wall with screws.
5. Adjust the Three-axis camera
bracket to obtain the
optimium viewing angle.
6. Adjust the Focus and Zoom
screw to achieve a clear
image.
7. Install the dome bubble on
the camera with the screws,
then carefully remove the
protective film to complete
the installation.
6
Tilt 0°~75°
Pan 0°~360°
Rotation 0°~360°
Zoom
Focus
Page 7
Camera OSD Menu
The Transcendent 4-in1 camera series must be connected to a DVR
which supports HD-TVI/AHD video signal input and COC protocol to
access the OSD setup menu. Different DVRs manufacturers may have
different modes of menu operation.
The Following image will pop-up when you left click once on the
image when using Transcendent HDA DVR's.
You will see the following interface by clicking the PTZ button.
Click on the OSD tab and then click on the camera menu
button.
You can select the menu by clicking (U) or (D) key on the
direction area. Click (L) or (R) key to select the menu on the
left. The menu with arrow icon which means it has sub-menu. You
can select the menu and click the Enter Button to enter the
sub-menu. to return to previous screen, arrow down to Return and
click Enter Button. To Exit menu arrow down to Exit and click Enter
Button.
7
Page 8
8910
Page 9
Page 10
Detailed Specifications VTC-THB5RV VTD-THD5RV
Image Sensor
Signal System
Effective Pixels
Resolution
Video Output
Frame Rate
Lens
Day/Night
Min. IIIumination
IR LEDs
IR Distance
S/N Ratio
WDR
Defog
Digital Noise Reduction (DNR)
White Balance
BLC
Up the COAX Control (COC)
Transmission Distance
Power Input
Power Consumption (12VDC)
Weather Resistance
Operation Conditions
Weight
Dimensions
36 Dynamic Intensity LEDs
120’
IR Off: 120mA / IR On: 480mA
IP66
21.16 oz. / 1.32 lbs. / 600g
3.43 x 8.62” (87mm x 219mm) Dia x L
1/2.5” 5.0 Megapixel Progressive Scan CMOS Sensor
PAL/NTSC
2592 x 1944
HD-TVI & AHD: 5.0 MegaPixel / CVI: 4.0 MegaPixel / CVBS: 960H
HD-TVI / AHD / CVI / CVBS (Selectable)
20fps
3.3-12mm (Varifocal)
True Day/Night by ICR
Color: 0.001 lux@F1.2, AGC ON / B/W: 0 lux (with IR ON)
30 Dynamic Intensity LEDs
100’
≥52dB (AGC Off)
D-WDR
YES
2D-DNR
Auto (AWB)
YES
YES
Up to 1500’ (Depending on cable characteristics & integrity)
12VDC
IR On: 120mA / IR Off: 360mA
IP66 / IK10
-4~122 / 10%~90% Humidity
34.22 oz. / 2.14 lbs. / 970g
5.91” x 4.49” (150 x 114mm) Dia x H
Page 11
OPTIONAL MOUNTS FOR
TRANSCENDENT CAMERAS
VT-TJB01
Junction Box for Cable
Management for use with all
Transcendent Bullet and Turret
Style Cameras
VT-TJB02A
Junction Box for Cable
Management for use with
Transcendent 30 IR LED Vandal
Domes
11
VT-TWM03
Wall Mount for Transcendent
30 IR LED Vandal Domes and
Varifocal Turret Cameras
Page 12
28492 CONSTELLATION ROAD VALENCIA, CA 91355
WWW.VITEKCCTV.COM
Version 1.0
December 2017
Loading...