Vita-Mix BarBos MP User Manual

FOODSERVICE

Owner’s Manual

Read And Save These Instructions

BarBoss®MP

Drink Machine MP

Maximum Performance Commercial Blender

All Models

Important Safeguards

1. Read all instructions.

2. To protect against risk of electrical shock, do not put motor base in water or other
liquid.

3. Close adult supervision is necessary when appliance is used by or near children.

4. Unplug the power cord from the wall outlet when the Vita-Mix
use, before disassembling, putting on or taking off parts, and before cleaning, other
than washing the container.

5. Never contact moving parts, especially the blades.

6. Do not operate any appliance with a damaged cord or plug or after the appliance
malfunctions or is dropped or damaged in any manner. Call Vita-Mix Service,
(800) 4DRINK4, (800-437-4654) or [phone] at once for possible
replacement, examination, repair, electrical or mechanical adjustment. If you
live outside the United States, contact your local Vita-Mix Distributor, or phone
the Vita-Mix International Division at [phone] or email
[e-mail] for a distributor in your country.

7. The use of attachments not recommended or sold by Vita-Mix Corporation may
cause fire, shock, or injury.

8.

Do not use outdoors.

9. Do not let the power cord hang over edge of table or counter, or touch hot surfaces.

10. Keep hands and utensils out of container while motor is running to prevent the
possibility of severe personal injury and/or damage to the Vita-Mix blender
scraper may be used, but only when the Vita-Mix blender is not running. With the
flexible rubber lid in place the accelerator tool may be used while motor is running.

WARNING: Blade is sharp. Handle carefully.

11.

• Never try to remove blade while container is sitting on the motor base.

• Do not operate with loose, nicked or damaged blade - replace immediately.

• To reduce the risk of personal injury, never place blade assembly on motor base
without blender container properly attached.

12. The maximum capacity is equivalent to the ounces (liters) listed on the container,
i.e. 32 oz. (900 ml) and substantially less with thick mixtures.

13. Container should not be more than 2/3 full when the accelerator tool is left in
place while blending. Do not exceed 30 seconds of continuous blending with
accelerator tool in place.

CAUTION: Cooling problems resulting in thermal shut-off and eventual motor

14.
damage may result if machine is operated in sound chambers other than those
approved by Vita-Mix.

15. Always operate the Vita-Mix blender with a lid in place.

16.

CAUTION: On all units with timers the light in the front panel START/STOP switch,
when lit, indicates the power to blender is ON and blender could start. Turn power
OFF, or unplug the machine before touching movable parts.

®

blender is not in

. A rubber

2

Important Safeguards

Enjoy the safety of this grounded appliance. The Vita-Mix blender’s U.S. power cord
comes equipped with a three-prong (grounding) plug which mates with a standard three­prong wall outlet (Figure A). This cord will vary for countries outside the United States.

Adapters (Figure B) are available for two-prong outlets. Do not cut or remove the
third (ground) prong from the plug or power cord.

Consult your electrician if you are not sure if the wall outlet is grounded through the
building wiring. With a properly grounded two prong wall outlet, ground the machine by
attaching the tab on the adapter to the wall outlet cover by means of the screw in the
center of the cover (Figure B).

THREE PRONG
ADAPTERS
ARE NOT TO
BE USED IN
CANADA.

Figure

A

Save These Safety Instructions

Figure B

3

Note on Timers: Stop mid cycle with

S

T

A

R

T

/S

T

O

P

TI

M

E

R

#

1

#

2

#

3

#

4

#

5

PULSE

M

ax

OFF

ON

START/STOP switch, not the
ON/OFF switch. If the ON/OFF
switch was used, wait 30 seconds for
power to recycle and the timer to
reset before resuming operation.

BarBoss®MP &
Drink Machine MP Model

ON/OFF switch. Located on the front of the
machine below the switch panel, controls the
power to the machine. With the machine plugged
in, switch the machine to ON to ready the
machine for blending. Shut OFF power switch
at night or whenever the machine will be left
unattended.

START TIMER switch. This is a lighted switch.
When light is lit power is ON. Depress START
TIMER switch to activate timer setting and again
to stop midcycle.

During operation, you may interrupt timer by
pressing ST

TIMER DIAL. Allows user to select a number
of timed settings. Increments on timer are
approximate seconds. Timer is activated
when the power switch is ON. Blender will shut
off automatically at the end of the pre-set time.

PULSE switch. Pulse button can only be used
when the power switch is ON. The PULSE
switch can be used to quickly refresh product
in the container by depressing the switch and
holding down as long as needed.

ART/STOP switch.

only

NOTE: Switches will become sticky from use. Use a wet cloth or sponge to flush and
clean in the groove around the water-shielded switches. You may also lightly spray
the surface around the switches with an all purpose cleaner (such as Cinch
and work the switches back and forth a few times to loosen any dried residue under
switch. Leaving switches sticky will damage or burn out the switches.

4

®

or 409®)

NOTE: Outside the United States and Canada, your machine may come with a different
container configuration.

Two-Part Lid

32 oz. (900 ml) Xtreme Performance Container

The two part lid is easy to clean and easy to put
on, take off and seal.

• To remove a fully latched lid, lift the two
tabs and pull upward and off.

• Twist the center lid plug to fasten or
remove.

NOTE: Older 48 oz. (1.4 L) and 64 oz. (2.0 L)
Vita-Mix container will work on the BarBoss or
Drink Machine MP. The Xtreme Performance
Containers will not work on older Vita-Mix
Machines. Call Vita-Mix or your distributor for
more information.

One Piece Lid

32 oz. (900 ml) Xtreme Performance Container

The one piece lid is easy to clean and easy to put
on, and take off and seal.

• There is no lid plug for this lid.

• Add ingredients through port on top.

(optional)

To secure lid plug, rotate it so one
tab locks between the stops on top
of rubber lid

Lift lid tabs
to remove lid

A

Figure

Figure B

NOTE: To make new lids easier to insert and remove, rub a light coating of cooking oil

around bottom where it seals. Place it in container for several minutes, remove and
lightly wipe oil off lid.

5

BarBoss®MP & Drink Machine MP Instructions

1. Set the container on the motor base by aligning it over the centering pad anchored to
the base. (Motor must be completely stopped before positioning container). Containers
are not to be used for hard, dry materials. Avoid running your machine with the container
empty.

2. Place liquids and soft foods in the container first, solid items and ice last. Prepare
food by cutting or breaking into 1-3 inch (3-8 cm) pieces. Frozen fruit should be as small
as practical.

3. Always use lid when blending. If blending hot ingredients, the lid must be securely in
place. When processing hot liquids, DO NOT use a non-latching lid.

4. Press ON/OFF switch to ON. Activate the timer by selecting the desired setting
on the dial and then depressing the START/STOP TIMER switch on the left.

NOTE:

Each setting on the dial (#1 - #5 and MAX Blend) is an increase in time and

speed. Your own testing will determine what setting will work best for your drinks.
4a. If mixture stops circulating, you have likely trapped an air bubble. Either insert the

tamper through the lid while blending, or stop the motor remove the container from
the base and stir or scrape the mixture from the sides of container into the center
using a rubber spatula to press any air bubbles away from the blades. Replace the
lid and continue blending.

Note:

START/STOP TIMER switch on your machine is lit when power is ON. Avoid
moveable parts. The timer stops working if machine is overloaded on low speed.
Reset the machine by turning power OFF for 15 seconds.

Warning: If you detect a change in the sound of the machine or if a hard or
foreign object comes into contact with the blades, do not serve the drink.
Inspect your blade assembly for loose, nicked or missing parts. If parts are
loose, missing, or nicked replace with new blade assembly. (See page 8.)

4b. To prevent possible splashing, lightly rest your hand on the lid while turning the

machine on (except when processing hot liquids).

4c. Due to the blending speed of the machine, processing times are greatly reduced

over standard machines. Until you become accustomed to the speed, watch your
mixture carefully to avoid over-blending.

4d. If stopping the machine mid-cycle, use the START/STOP switch, not the POWER

switch. If the POWER switch was used, wait 30 seconds for power to recycle and
the timer to reset before resuming operation.

5. After blender has been turned off, wait until blade comes to a complete stop before
removing the lid or container from the motor base.

6

Note:

The thermal protector shuts the motor off to protect it from overheating. To restart,
wait for motor to cool down with the power OFF (up to 30 minutes). When this happens,
review your processing techniques and your instructions. Your recipes may be too thick
or have too much material in them.
Cooling may be quickened by placing the motor base in a refrigerator or a cool spot.
Unplug first. To speed up the process try circulating the air with a vacuum or fan aimed
at the bottom of the base. If the motor seems to be over heating (and the thermal
overload protector has not turned the machine OFF), remove the container from the
base. Set the timer for 20 seconds. Turn the machine ON and let the machine run for
20 seconds. Repeat this step 3 times for a total of 1 minute.

6. To use the PULSE switch: Press ON/OFF switch to ON. With the container on the
motor base depress the PULSE switch. Release the switch to turn off the motor.

7

Blade Agitator Assembly. Blades are sharp; use

4

8

16

2

4

32

caution when handling the blade. When inserting the
blade assembly through the container bottom, align the
flat sides. Gravity holds it in place while the retainer nut
is tightened. Do not attempt to disassemble this part.

Drive Spline. Mates with drive socket on the motor
base to turn the blade. Note: Removing and replacing
your container while the coupling is still rotating will
strip the drive spline “teeth”. (This part is NOT
removable.)

Retainer Nut. Must be snug. Order the available
retainer nut wrench for best results. (Refer to the
diagram below to remove or replace.)

Never use a blade assembly with loose, damaged or nicked components.

Blade Assembly Removal

CAUTION: Do not remove blades unless absolutely necessary!

At times, it may be necessary to give your blades additional
cleaning. An easy-to-use blade assembly removal wrench
(Item #15596) may be purchased through your Vita-Mix
distributor.

apart. This will void the warranty.

Turn the container upside down and grip firmly. Insert retainer
nut wrench in groove of retainer nut and rotate counterclock­wise to loosen. Then grip blades with a cloth and remove
retainer nut by hand.

Replacing Blade Assembly

With the container upside down, grip blades with cloth, insert
into the container bottom and align with flat sides of container
opening. Place retainer nut on and hand tighten. Last, carefully
turn clockwise until secure, using wrench. Do not force. If it is
not tight enough, you will notice increased container noise.

Never attempt to take the blade assembly itself

Retainer Nut Wrench

Retainer Nut Wrench
in use.

8

The Accelerator Tool prevents an air bubble

4

8

16

24

32

40

48

OUNCES

from forming while blending. It is used when
making frozen ice creams, pureeing fruits
and vegetables, (or whenever your mixture
requires it). It also permits you to push
ingredients down around the blades while
the Vita-Mix blender is running.

Accelerator Tool

use:

• Use only with the lid in place and the

center lid plug removed.

• The splash disc prevents the

from hitting the blades when insert-

Tool

Accelerator

ed through the lid.

• Container should not be more than

2/3 full (just below the indicated
maximum capacity for XP containers)
when the

Accelerator Tool

is left in place

while blending.

• To avoid overheating, do not exceed

30 seconds of continuous blending

Accelerator Tool

with

in place.

• If thick mixtures stop circulating, you

have likely trapped an air bubble.

Accelerator Tool

Insert

through the lid

and stir to release it.

• Holding the

Accelerator Tool

at an angle
near the side and pushing towards the
center will be more effective when
creating a thicker, smoother drink.

*NOTE: Accelerator Tools have a small step
on them. The step prevents the Accelerator
Tool from coming into contact with the blades
in Vita-Mix polycarbonate containers.
Accelerator Tool cannot be used with a one
piece non-latching lid.

9

Care Note

To ensure that you get the longest possible life from your Vita-Mix product, we recom­mend the following products, when used as directed by the supplier:

Cleaning Product. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Supplier

Solid Supra, Solid Power,.. . . . . . . . . . . . . . . . . . . . . . . . Ecolab, Inc., St. Paul, MN

Guardian Acclaim, Solid Guardian Plus,. . . . . . . . . . . . . [phone]

Solid Super Impact, Solid Insure. . . . . . . . . . . . . . . . . . . www.ecolab.com

Diverpak. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Eclipse H2, Liqui-Safe L7 . . . . . . . . . . . . . . . . . . . . . . . . [phone]

Acclean . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Poly-Brite . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Division of Ecolab

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . St. Paul, MN

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [phone]

Glow MB-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Lustre NC-25 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Seattle, WA

Lustre Plus. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [phone]

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . www.wesmar.com

PSRA 41-D, PSRA 41-E . . . . . . . . . . . . . . . . . . . . . . . . .

Liqui-Ware 1, Liqui-Ware MC . . . . . . . . . . . . . . . . . . . . . Litchfield, MN

D-Flex, Sur-Met . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [phone]

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . www.andersonchemical.com

Rinse Aids . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Supplier

Solid Rinse Dry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ecolab, Inc., St. Paul, MN

Solid Brilliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [phone]

Jet Dry, Rinse Dry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . www.ecolab.com

Destainer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Supplier

NuWare . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Diversey, Livonia, MI

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [phone]

Diversey, Livonia, MI

Klenzade Products

Wesmar Company, Inc.

Anderson Chemical Co.

Do not use abrasive cleaning agents or concentrated bleach
when cleaning. Do not use any cleaners containing Quatinary Sanitizers
on polycarbonate components (i.e., containers).

Switches will become sticky from use. Use a wet cloth or sponge to flush and

NOTE:

clean in the groove around the water-shielded switches. You may also lightly spray the

®

surface around the switches with an all-purpose cleaner (such as Cinch

or 409®) and
work the switches back and forth a few times to loosen any dried residue under switch.
Dirty switches may burn out.
ADDITIONAL NOTE: Do not let mixtures, liquids and food products dry within the
container. Rinse throughout use. Drying may lock around the blade and weaken/tear
the bearings seal when restarted. Do not place containers in the freezer. Extremely
low temperature combined with hot ingredients and/or the immediate rapid action of the
blade may crack the container. Due to the nature of polycarbonates, microwaving and
automatic dishwashing are not recommended. Follow the cleaning instructions on page 11.

10

Motor Base

1. Unplug the power cord.

2. Wash outside surface with a damp, soft cloth or sponge, which has been rinsed in a

mild solution of liquid dish soap (Ivory Liquid
IMMERSE MOTOR BASE IN WATER OR OTHER LIQUID.

3. Thoroughly clean switches so that they work freely. They will become sticky from

use. Use a wet cloth or sponge* to flush and clean in the groove around the water
shielded switches. You may also lightly spray the surface around the switches with
an all-purpose cleaner such as Cinch
a few times to loosen any dried residue under switch.

4. Polish with a soft cloth.
*Note: Be sure to wring excess water out of cloth or sponge when cleaning around the

controls or any electrical part.

®

or equivalent) in warm water. NEVER

®

or 409®and work the switches back and forth

Lid

Separate the lid and plug, then wash in warm soapy water. Rinse clean under running
water and dry. Reassemble before use. (See page 5).

Container

1. To clean: Fill pitcher 1/4 full with warm (110˚F/43˚C) water and add a couple drops

of dish soap.** Return container to motor base and firmly position the two part lid.
Run machine for 30 seconds. Empty container. Repeat this step.

**

Note: To prolong polycarbonate container life, Vita-Mix recommends using soaps
with a low Ph balance, such as a manual pot and pan detergent. Due to the nature
of polycarbonates, automatic dishwashing is not recommended.

2. Fill pitcher 3/4 full with warm (110˚F/43˚C) water (do not add soap). Return container

to motor base and firmly position the two part lid. Run machine for 30 seconds.
Empty container.

3. If any solid residue remains, remove the blade agitator assembly (see page 8) and

wash all container parts in warm soapy water. Rinse and drain. Reassemble before
next step.

4. To sanitize: If all solid residue is gone after step 2 or after completion of step 3,

fill container 3/4 full with a sanitizing solution mix.*** Return container to motor base
and firmly position the two part lid. Run machine on HIGH for 30 seconds. Empty
container.

5. Return container to motor base and run machine empty for an additional 5 seconds.

Do not rinse after sanitizing.

*** Recommended sanitizing solution: 1-1/2 teaspoons institutional or household

bleach in 2 quarts (2 liters) water

.

11

BarBoss®MP & Drink Machine MP

4

8

16

24

32

40

48

OUNCES

NOTE: Outside the United States and Canada, your machine may come with a different
container configuration. Contact your local Vita-Mix distributor for part numbers.

Item # Part

#760 Accelerator tool

#15578 Sound-reducing XP centering pad

PLS209 Variable speed control knob / timer control knob

#891 Drive socket

XDM039 Owner’s Manual

#15585 XP retainer nut
#15598 XP blade agitator assembly
#15571 32 oz. (900 ml) polycarbonate Xtreme Performance container with lid

and lid plug

#15574 2-piece thermoplastic rubber lid for 32 oz. (900 ml) Xtreme

Performance container

#15570

#15573 32 oz. (900 ml) polycarbonate stackable Xtreme Performance

*Notice: Other than the drive socket, blade assembly and retainer nut, this unit
is not user serviceable.

#15574

#15571

32 oz. (900 ml) polycarbonate stackable Xtreme Performance
container, ice blade & lid assembly

container only

#755

#15575

#15573

#15596

Retainer Nut Wrench

(sold separately)

12

#15585

#891

#15578

#PLS145

One-Piece Lid

(sold separately)

PLS209

#760

#15598

Top four problems you can fix on your own

1. Problem:

• increased vibration

• leaking from bottom of container

• increased container noise

Solution #1:

Check blade assembly for loose, damaged
or nicked components and replace.

Solution #2:

Tighten retainer nut with screwdriver
moving clockwise until it is snug. See p. 8.

2. Problem:

• Machine will not run.

3. Problem:

• loud noise from blade area

• blades don’t spin

4. Problem:

• Machine will not run when START
TIMER switch is activated.

Solution #1:

Double-check to make sure power cord is
firmly in power outlet.

Solution #2:

Check to make sure switches are clean
and moving freely.

Solution #3:

The thermal protector may have turned
the machine OFF. Turn power OFF for up
to 30 minutes to reset.
be quickened by placing the motor base in
a refrigerator or cool spot. (Unplug first).
To speed up the cooling process, try circu
lating the air with a fan or vacuum at the
bottom of the motor base.

Note: Cooling may

Solution:

Drive socket may be broken. Check for a
fine crack down the center or worn teeth­replace with a new drive socket. (Item #891).
Instructions are included with part.

Solution:

Check ON/OFF switch to make sure the
switch is in the ON position.
TIMER switch is lit when power is on.

Note: START

-

Timer stops working if machine is overloaded on low speed. Reset by turning power
OFF for 15 seconds. Do not turn power OFF midway through a blending cycle.
To interrupt cycle, press START/STOP TIMER switch one time. See page 4.

If you cannot fix your machine with these suggestions, technical help is available by
calling 800-4DRINK4 (800-437-4654). If outside the United States and Canada,
contact your local Vita-Mix distributor or phone the V
[phone] or email [e-mail] for a distributor in your country.

ita-Mix International Division at

13

Vita-Mix Corporation warrants your Commercial Vita-Mix appliance to be free from
defects in materials and workmanship for a period of three years from the date of
purchase when used in accordance with the accompanying instruction booklet.

Provisions of this limited warranty are void if your Vita-Mix appliance has been
subjected to obvious abuse, negligence, accident, alteration, or failure to follow
operating instructions, or product exposure to abnormal or extreme conditions.
Cosmetic changes such as discoloration of parts of the product in the hands of the
user or the effects of the use of abrasive cleaners will not be warranted or considered
defects. The cleaning or removal of food products along with any damage caused by
allowing them to build up is not covered by this limited warranty. Warranty is void if
the Vita-Mix blender is put into a sound reduction chamber that does not allow
proper cooling.

In the event your Vita-Mix appliance needs service or repair covered by the terms of
this warranty, please call the Vita-Mix Corporation for shipping instructions. The Vita-Mix
blender must be sent in original or sufficient packaging.

This limited warranty is in lieu of any other warranty expressed or implied. No
representative or any other person is authorized to make any other warranty or to
assume any liability not strictly in accordance with the foregoing. This limited warranty
gives you specific legal rights which may vary from state to state. Proof of purchase
may be required to prove date of purchase.

Outside the Continental United States and Canada other warranties may apply

(Call or check with your local Vita-Mix distributor for details). In case of shipping damage,
notify the shipper or carrier immediately. Outside the United States and Canada, contact
your local Vita-Mix Distributor.

.

14

PLEASE NOTE: The Service Contract outlined in the following paragraphs applies
only to customers in the United States and Canada. Customers in all other countries
should contact their local Vita-Mix

®

distributor for service details.

This Vita-Mix blender includes a 1-Year Service Contract effective from date of
purchase. In the event your machine should need parts or repairs, covered under this
Service Contract, call Vita-Mix customer service immediately for instructions. Proof of
date of purchase may be required. This does not cover abuse, misuse, tampering,
improper installation or extreme conditions.

The Vita-Mix Service Contract includes the following:

1. Only one extra drive socket - to facilitate simple repairs and prevent down time is
included and packaged with each machine.

2. Additional drivers and accelerator tool, unless defective, are not covered. NOTE: to
determine if you have a defective part, please order a replacement part through
Vita-Mix Customer Service and, when the new part arrives, return the old part in the
same packaging. Vita-Mix will inspect the returned part and, if defective, issue a
refund for the price of the new part. A part will be considered defective if no abuse or
neglect was involved with its break. Non defective parts sent to Vita-Mix for inspection
will not be returned if deemed unusable. Service Contract covers functionality of the
machine but not abuse or lack of recommended maintenance.

3. In the continental United States, sender pays freight one way to V

ita-Mix
Corporation. The Vita-Mix Corporation will pay UPS ground freight charges to return
the machine to the sender. Sender pays costs for special shipping requests. Outside
Continental United States, other service contracts may apply.

Before returning this product for any reason, including repair, please, first contact our
CUSTOMER SERVICE DEPARTMENT: (800) 4DRINK4, [phone] or [phone]
to receive a “RETURN AUTHORIZATION NUMBER”.

Note: Within the United States, Limited Warranty and Service Contract are honored
directly through the Vita-Mix Corporation, Cleveland, Ohio USA. Non-warranty repairs
can be performed by any CFESA service center. For machines sold in the USA, call
Vita-Mix (800) 4DRINK4 (800-437-4654) or [phone].

15

Dimensions:

NSF

®

Height of Motor Base: 8-1/2” (21.25 cm)

• with 32 oz. (900 ml) polycarbonate Xtreme Performance container

and lid: 18” (45.72 cm)

• with 32 oz. (900 ml) polycarbonate Xtreme Performance container

without lid: 16” (40.64 cm)

32 oz. (900 ml) polycarbonate Xtreme Performance container with lid,
no base: 10-3/4” (27.31 cm)

Dimensions: 8” W x 9” D x 18” H (20.3 cm x 22.9 cm x 45.72 cm)

Ship weight of machine: 13 lbs. (6 kg)

Power Requirements:

Volts: 120 VAC
Amps: 11.5
Hz: 50/60

Volts: 220/240 VAC
Watts: 750-850
Hz: 50/60

Volts: 100 VAC (Japan)
Watts: 900
Hz: 50/60

When applicable:

N

The instructions appearing in this Owner’s Manual cannot cover every possible
condition and situation that may occur. Common sense and caution must be
practiced when operating and maintaining any appliance.

VITA-MIX®CORPORATION

Foodservice Division

8615 Usher Road, Cleveland, Ohio 44138-2103 USA

©2005 Vita-Mix Corporation. No part of this publication may be reproduced or transmitted in any form or

by any means, electronic or mechanical, including photocopy, recording or any information storage and retrieval system

Printed in U.S.A.

without the written permission of the Vita-Mix Corporation.

XDM039 11/05