Vista VBC28V12MHDA, VPC-DNHDA, VEFED28V12MHDAW Installation Manual

Installation Manual

VBC28V12MHDA

Please read this manual thoroughly before use and keep it handy for future reference.

2

3

Before You Begin

Read these instructions before installing or operating this product.
Note: This installation should be made by a qualified service person and should conform to local codes.

This manual provides installation and operation information. To use this document, you must have the following
minimum qualifications:

• A basic knowledge of CCTV systems and components

• A basic knowledge of electrical wiring, low-voltage electrical connections and IP networking/infrastructure

Intended use

Only use this product for its designated purpose; refer to the product specification and user documentation.

Customer Support

For assistance in installing, operating, maintaining and troubleshooting this product refer to this document and
any other documentation provided. If you still have questions, please contact Norbain Technical Support and
Sales:

Norbain SD, 210 Wharfedale Road, Winnersh Triangle, Wokingham, Berkshire RG41 5TP, England.
UK [phone] / Vista Technical Support [phone]

Note: You should be at the equipment and ready with details before calling Technical Support.

Conventions Used in this Manual
Boldface or button icons highlight command entries. The following WARNING, CAUTION and Note statements

identify potential hazards that can occur if the equipment is not handled properly:

* WARNING:

Improper use of this equipment can cause severe bodily injury or equipment damage.

* CAUTION:
Improper use of this equipment can cause equipment damage.

Note: Notes contain important information about a product or procedure.

This apparatus is manufactured to comply with the radio interference.
A Declaration of Conformity in accordance with the following EU standards has been made. The
manufacturer declares that the product supplied with this document is compliant the provisions of
the EMC Directive 2004/108/EC, the CE Marking Directive 93/68 EEC and all associated
amendments.

All lead-free products offered by the company comply with the requirements of the European law
on the Restriction of Hazardous Substances (RoHS) directive: 2011/65/EU, which means our
manufacture processes and products are strictly “lead-free” and without the hazardous
substances cited in the directive.

The crossed-out wheeled bin mark symbolizes that within the European Union the product must
be collected separately at the product end-of-life. This applies to your product and any
peripherals marked with this symbol. Do not dispose of these products as unsorted municipal
waste.

* This symbol indicates electrical warnings and cautions.
** This symbol indicates general warnings and cautions.

NORBAIN SD reserves the right to make changes to the product and specification of the product from time to
time without prior notice.

WARNINGS AND CAUTIONS:

To reduce the risk of fire or electric shock, do not insert any metallic objects through the ventilation grills or other
openings on the equipment.

4

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Clean only with dry cloth.

6. Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions.

7. Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.

8. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug
has two blades with one wider than the other. A grounding type plug has two blades and a
third grounding prong. The wide blade or the third prong is provided for your safety. If the
provided plug does not fit into your outlet, consult an electrician for replacement of the
obsolete outlet.

9. Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.

10. Only use attachments/accessories specified by the manufacturer.

11. Unplug this apparatus during lightning storms or when unused for long periods of time.

12. Refer all servicing to qualified service personnel. Servicing is required when the apparatus
has been damaged in any way, such as power-supply cord or plug is damaged, liquid has
been spilled or objects have fallen into the apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or has been dropped.

13. CAUTION – THESE SERVICING INSTRUCTIONS ARE FOR USE BY QUALIFIED
SERVICE PERSONNEL ONLY. TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT
PERFORM ANY SERVICING OTHER THAN THAT CONTAINED IN THE OPERATING
INSTRUCTIONS UNLESS YOU ARE QUALIFIED TO DO SO.

14. Use satisfy clause 2.5 of IEC60950-1/UL60950-1 or Certified/Listed Class 2 power
source only.

CE COMPLIANCE STATEMENT

WARNING

This is a Class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.

5

Table of Contents

1 — Introduction ................................................................................................................ 6

1.1 Features ............................................................................................................................... 6

2 — Installation and Configuration ................................................................................... 7

2.1 Package Contents ............................................................................................................... 7

2.2 Camera Overview ................................................................................................................ 7

2.3 Connections / Tact Switch Operation & Lens Control ...................................................... 7

2.4 OSD Menu Structure ........................................................................................................... 9

3 — OSD Menu ................................................................................................................. 10

3.1 Lens .................................................................................................................................... 10

3.2 Exposure ............................................................................................................................ 10

3.3 Backlight ............................................................................................................................ 10

3.4 White Balance .................................................................................................................... 11

3.5 Day&Night .......................................................................................................................... 11

3.6 Image .................................................................................................................................. 11

3.7 Function ............................................................................................................................. 12

3.8 System ............................................................................................................................... 13

3.9 AF ....................................................................................................................................... 13

3.10 Exit.................................................................................................................................... 13

4 — Specifications ........................................................................................................... 14

4.1 Technical Specification .................................................................................................... 15

4.2 Line Drawing / Dimensions............................................................................................... 16

6

1 — Introduction

1.1 Features

1/2.9” Sony 2.2MP Exmor CMOS
1080p in TVI and AHD, 1000TVL in CVBS

2.8-12mm motorized lens (controlled via tact switch or coax telemetry)

1.0Lux (colour), 0Lux (mono – IR on)

● True Day/Night operation

● 42, 850nm IR LEDs

● 40m IR illumination

● Smart IR

● Auto electronic shutter (1/25 to 1/50,000) and manual electronic shutter modes

● Day & Night – Auto, Colour, B&W (Monochrome)

● OSD - On Screen Display (via tact switch or coax telemetry)

● DWDR

● AGC (Auto Gain Control)

● DNR (Digital Noise Reduction)

● Auto and manual white balance modes (ATW/AWC/Manual/AWB)

● BLC (Back Light Compensation)

● HSBLC (Peak White Inversion)

● Flickerless

● Sens-Up

● 4 Privacy zones

● 4 motion detection zones

● Functions (Mirror, Brightness, Sharpness, Flip)

12/24V operation
Use clause 2.5 of IEC60950-1/UL60950-1 or Certified/Listed Class 2 power source only.