Page 1
POWERMAX
POWERMAX PRO
POWERMAXPOWERMAX
PRO
PRO PRO
Fully Supervised Wireless Alarm Control System
TABLE OF CONTENTS
TABLE OF CONTENTS
TABLE OF CONTENTSTABLE OF CONTENTS
1. INTRODUCTION...........................................................3
2. SPECIFICATIONS ........................................................3
2.1 General Data...........................................................3
2.2 RF Section..............................................................4
2.3 Electrical Data.........................................................4
2.4 Communication.......................................................4
2.5 Physical Properties.................................................4
3. INSTALLATION.............................................................4
3.1 Unpacking the Equipment........................................4
3.2 Supplying Power to the Unit....................... ..............4
3.3 System Planning and Programming.........................4
3.4 Mounting .................................................................4
3.5 Wiring.......................................................................4
3.6 Backup Battery Insertion..........................................6
3.7 X-10 Interface Module Connection............................ ....6
3.8 Optional GSM Module M oun ting................. .......... ..... ....6
3.9 Additional Optional Module Mounting.......................6
3.10 Power Cable Connection......... ..............................7
3.11 Installing an Optional X-10 Siren............................9
3.12 Connecting PowerMax Pro to a Computer.............9
3.13 Connecting PowerMax Pro to GSM Modem..........9
4. PROGRAMMING ........................................................10
4.1 INTRODUCTION........................................................10
4.1.1 General Guidance...................................... .........10
4.1.2 Entering an Invalid Installer Code.......................10
4.1.3 Installer's Menu...................................................10
4.1.4 Setting a New Installer Code...............................10
4.1.5 Setting a New Installer Code in PowerMax Pro
that has 2 Installer Codes...................................10
4.2 ENROLLING WIRELESS DEVICES AND KEYFOBs11
4.2.1 General Guidance...............................................11
4.2.2 Enrolling Type.....................................................12
4.2.3 Enroll / Delete Wireless Devices.........................12
4.2.4 Enroll / Delete Keyfob Tra ns mitters ....................12
4.2.5 Enroll / Delete Wireless Commander..................12
4.2.6 Enroll / Delete 2-Way Keypad.............................12
4.2.7 Enroll / Delete Wireless Siren....... ...................... 12
4.2.8 Enroll / Delete Proximity Tags .............................13
4.3 DEFINING ZONE TYPES, NAMES & CHIME ZONES12
4.4 DEFINING CO NTR O L PANEL PARAMETERS ........13
4.4.1 Preliminary Guidance..........................................13
4.4.2 Entry Delays 1&2 .................................... ............13
4.4.3 Exit Delay............................................. ...............13
4.4.4 Bell Time........ ...................... ...................... .........13
4.4.5 Abort Time...........................................................13
4.4.6 Alarm Cancel ......................................................13
4.4.7 Quick Arm...........................................................14
4.4.8 Bypass................................................................15
4.4.9 Exit Mode............................................................15
4.4.10 Piezo Beeps......................................................15
Installer Guide
4.4.11 Trouble Beeps..................................................15
4.4.12 Panic Alarm......................................................15
4.4.13 Swinger Stop....................................................15
4.4.14 Cross Zoning....................................................15
4.4.15 Supervision.......................................................15
4.4.16 NOT READY.....................................................15
4.4.17 AUX Button A...................................................15
4.4.18 AUX Button B 2-W-KF......................................15
4.4.19 Jam Detect.......................................................15
4.4.20 Latchkey...........................................................15
4.4.21 “Not Active”.......................................................16
4.4.22 Back Light.........................................................16
4.4.23 Duress..............................................................16
4.4.24 Piezo Siren.......................................................16
4.4.25 Reset Options...................................................1 6
4.4.26 Tamper Option..................................................16
4.4.27 Siren on Line....................................................16
4.4.28 Memory Prompt................................................1 6
4.4.29 Disarm Option ..................................................16
4.4.30 Bell/Rep. Option...............................................16
4.4.31 Low-Bat ACK ....................................................16
4.4.32 Screen Saver....................................................16
4.4.33 Confirm Alarm ..................................................1 6
4.4.34 AC Fail Rep......................................................16
4.4.36 User Pe rmission...............................................16
4.5 DEFINING COMMUNICATION PARAMETERS....... 18
4.5.1 Autotest Time.............................................. .......18
4.5.2 Autotest Cycle....................................................18
4.5.3 Area Code................................................... .......18
4.5.4 Out Access Code............................... ................18
4.5.5 First Central Station Telephone..........................18
4.5.6 First Account No.......................................... .......18
4.5.7 Second Central Station Telephone ....................18
4.5.8 Second Account No............................................18
4.5.9 Report Format....................................................18
4.5.10 4/2 Pulse Rate..................................................18
4.5.11 Reporting to Central Stations...........................18
4.5.12 Report CNF Alarm............................................1 8
4.5.13 Send 2WV Code ..............................................18
4.5.14 Two-Way Voice Central Stations.....................18
4.5.15 Ring Back Time................................................19
4.5.16 Dialing Attempts...............................................19
4.5.17 Set Private Telephone No. ...............................19
4.5.18 Two-Way Voice - Private Phones....................19
4.5.19 Private Telephone Dialing Attempts.................19
4.5.20 Reporting to Private Telephones......................19
4.5.21 Telephone Acknowledge..................................19
4.5.22 Pager Telephone Number................................ 19
4.5.23 Pager’s PIN No.................................................19
4.5.24 Reporting to a Pager........................................19
DE5468IP 1
Page 2
4.5.25 Recent Closure.................................................19
4.5.26 Remote Access.................................................19
4.5.27 Master Downloader Code .................................19
4.5.28 Installer Downloader Code................................19
4.5.30 Zone Restore....................................................19
4.5.31 Upload Option...................................................19
4.5.32 Dialing Method..................................................21
4.5.33 Line Failure Report............................................21
4.5.34 UL/DL Telephone Number................................21
4.5.35 System Inactive Report.....................................21
4.5.38 Ambient Level...................................................21
4.6 DEFINING GSM PAR AMETERS......................... ......21
4.6.1 GSM installed......................................................21
4.6.2 1st, 2nd, 3rd & 4th SMS Numbers ......................21
4.6.3 Reporting to SMS Phone Number.......................21
4.6.4 GSM Line Failure Reporting................................22
4.6.5 GSM Line Purpose..............................................22
4.7 DEFINING POWERL INK...........................................22
4.8 DEFINING OUTPUT PARAMETERS ............ ............22
4.8.1 Preliminary Guidance..........................................22
4.8.2 Defining PGM .....................................................23
4.8.3 Defining INT/STRB..............................................23
4.8.4 X-10 General Def................................................23
4.8.5 X-10 Unit Define............................... ...................23
4.9 DEFINE VOICE........................................... ...............25
4.9.1 Record Speech ...................................................25
4.9.2 Voice Box Mode .................................................25
4.10 DIAGNOSTIC TEST.................................................25
4.11 USER FUNCTIONS .................................................26
4.12 RETRIEVING FACTORY DEFAULTS.....................26
4.13 SERIAL NUMBER....................................................26
4.14 CALLING UPLOAD/DOWNLOAD SERVER ...........26
5. TESTING PROCEDURES ...........................................27
5.1 Preparations .........................................................27
5.2 Diagnostic Test.....................................................27
5.3 Keyfob Transmitter Test.......................................27
5.4 Appliance ON/OFF Test.......................................2 7
5.5 Emergency Transmitter Test................................28
6. MAINTENANCE ..........................................................28
6.1 Dismounting the Control Panel.............................28
6.2 Replacing the Backup Battery............................. .28
6.3 Fuse Replacement...............................................28
6.4 Replacing/Relocating Detectors ...........................28
7. READING THE EVENT LOG......................................28
APPENDIX A . DETEC TOR DEPLOYMENT AND
TRANSMITTER ASSIGNMENTS....... ....................... 29
A.1 Detector Deploym en t Pla n...................................29
A.2 Keyfob Transmitter List........................................29
A.3 Emergency Transmitter List.................................30
A.4 Non-Alarm Transmitter List..................... ... ..........30
APPENDIX B. X-10 UNIT AND PGM OUTPUT
ASSIGNMENTS.........................................................30
APPENDIX C. EVENT CODE S............. ...................... .... 31
APPENDIX D. PROGRAMMABLE ZONE TYPES.......... 32
APPENDIX E. POWERMAX PRO COMPATIBLE
DEVICES.........................................................................33
E1 PowerMax Pro Compatible Detectors....................33
E2 PowerMax Pro Compatible Transmitters ...............34
E3 PowerMax Pro Comp a tib le WL Siren.......... ... .......34
E4 PowerMax Pro Com p a tib le GSM Modem..............34
E5 PowerLink.............................................................. 34
FCC Statements............................................................. 35
MESSAGE TO THE INSTALLER
The PowerMax Pro control panel is supplied with 2 inst ruction manuals:
!
! Installer Guide (this manual - for your exclus ive use)
!!
!
! User’s Guide (for your use during installation only - Must be handed over to the master user after testing the system).
!!
Appendices A.1 and A.2 will help you prepare an installation plan. Please take time to fill out the forms - your job will
become much easier and confusion will be prevented. Filling out the forms will also help you create a list of detectors and
transmitters that must be obtained for the particular application. Compatible detectors and transmitters are listed and
described briefly in Appendix E.
Remember - it is advisable to power up th e control panel te mporaril y after un pack ing and pro gram it on the work bench, in
accordance with the installation plan.
The programming f low charts i n the progr amming sectio n show all options a vailable f or each pa rameter. Factory de faults
are marked with a dark box to thei r right, an d other opti ons (that can be sel ected inst ead) are marke d by clear boxes. This
method allows you to put a checkmark in the appropriate clear box whenever you deviate from the factory defaults .
Most of the programming section paragraph numbers correlate with the programming menu numbers. For example,
paragraph 4.4.19 des cribes the "Jam detect", that exists in menu 4 (define panel), s u b-menu 19 (Jam detec
Although sett ing the correct time and date i s one of the user task s, we recommend t hat you set the time and date in the
course of programming. Acces s t o the “User Settings ” f or the installer is possible through item 10 on the installer‘s menu or
through the user menu (s ee User’s manual section 7).
After programming, proceed to install the system as detailed in the Installation Instructions, from paragraph 3.4 onward.
t).
The installer s hould verif y line seizure. Be aware of other p hone line services such as DSL. If DSL service is pre sent
on the phone line, you must install a filter. It is suggested to use the DSL alarm filter model Z-A431PJ31X
manufactured by Excelsus Technologies, or equivalent. This filter simply plugs into the RJ-31X jack and allows
alarm reporting without breaking the internet connection.
2 DE5468IP
Page 3
1.
1. INTRODUCTION
INTRODUCTION
1.1.
INTRODUCTION INTRODUCTION
The PowerMax Pro is a user and installer-friendly, 30-zone
fully-supervised wireless control system. The system is
designed t o functi on in a way that appe als to t he user but
also offers features that make installers’ life easier than
ever before:
EASY TO INSTALL
•
Plug-in terminal blocks can be wired while detached
from the unit.
•
Quick attach-detach TELCO sockets for telephone line
and X-10 control ler. Terminal bloc k for teleph one line &
set.
•
Special wall-mounted bracket permits installation without
having to open the unit’s cabinet.
•
Optional plug-in dual RS-232 module that enables a
concurrent conn ec tio n of an ex te rnal GSM, Powerli nk, or
local computer (only 2 simultaneous device
connections).
EASY TO MAINTAIN
•
Status, alarm memory and trouble data are displayed
upon request.
2222.... SPECIFICATIONS
SPECIFICATIONS
SPECIFICATIONS SPECIFICATIONS
2.1 General Data
Zones Number: 28 wireless, 2 hardwired ( zones 29 & 30) .
Hardwired Z one Requirements: 2.2 kΩ E.O.L. resistance
(max. resistance of wires 220 Ω).
Zone Types: Interior follower, interior, perimeter, perimeter
follower, delay 1, delay 2, 24h sil ent, 24h au dible, f ire, nonalarm, emergency, gas and flood.
User Codes: 8 codes, 4 digits each (9999 different
combinations) . Code 0000 is not a llowed.
Control Facilit ies:
- Integral keypad
- PowerCode / Code-Secure™ hand-held transmitters
- Wireless commander, MCM-140+
- Remote telephone
- Local or remote computer
Display: Sing le line , Backlit 16-character LC D.
Arming Modes: AWAY, HOME, AWAY-INSTANT,
HOME-INSTANT, LATCHKEY, FORCED, BYPASS.
Alarm inhibited during a single ar ming per iod (swinger
stop) after: 1, 2, 3, alarm/tamper/fault, or not inhibited
(programmable / selectable).
Alarm Types: Silent alarm, siren alarm or sounder
(internal) alarm, i n accordance with zone att ri butes.
Siren Signals: Continuous
triple pulse - pause - triple pulse...
Siren (bell) Timeout : Programmable (4 min. by defaul t)
Internal Sounder Output: At least 85 dBA at 10 ft (3 m)
Supervision: Programmable time frame for ina c tivity alert
Special Functions:
- Speech and sound control
- Powerline Carrier Device Control (up to fifteen X-10
brand units) by various factors, as program med
(intrusion / 24 hours / panic);
(fire).
•
Diagnostic test provides visual and audible indication of
the signal level of each detector .
•
Remote control and status verification from distant
telephones.
•
Event log stores and displays information on 250 past
events.
•
Upload / download fr om distant computer via telephone
line and modem.
QUICK PROGRAMMING
•
Multiple-choice selection of options for each parameter.
•
Unequivocal visual prompts and audible si gnals.
•
Installer access to the user menu.
A fully equipped alarm system based on the PowerMax
Pro consist s of the units shown in Figure 2 of the user ’s
guide.
The basic PowerMax Pro k it includes installer gu ide, user
guide, backu p battery pack , 3 flat ca bles , telepho ne cabl e,
screws, NEXT MCW detector , MCT-2 34 keyf o b trans mit te r
and MCT-302 magnetic cont act transmitter.
- Chime zones
- Diagnostic test an d event log
- Remote control by telephone
- Computer control and dat a dow nload/upload
- Calling for hel p by using an emergency transmi tter
- Tracking inacti vity of elderly, physi c ally handicapped and
infirm people
- Message center (rec or ding and playback)
- Two-way voice communicat ion
Data Retrieval: Status, alarm memory, trouble, event log.
Real Time Clock (RTC): The control panel keeps and
displays time and date.
Compliance with U.S. Standar d s:
Meets FCC Part 15 and Part 68 requirements.
Compliance with CE Stan d ard s :
EN 50082-1, EN301489-3,7, EN6100-4-6, EN60950
According to the European standard EN50131-1, the
PowerMax Pro security grading is 2 – "low to medium risk "
and environmental cl assific ation is II – "indoo r general" and
the power supply type is A.
The PowerMax Pro is compatible with the RTTE
requirements - Directive 1999/5/EC of the European
Parliament and of the Council of 9 March 1999.
GSM standards:
Europe : Complies with CE standards 3GPP TS 51.010-
1, EN 301 511, EN 50361, EN 3014 89- 7
USA: FCC 47 Part 22 (GSM850) and Part 24 (GSM
1900).
EMC standard: F CC 47 Part 15.
SAR standards: FCC rule 2.1093, FCC Docket 96-326 &
Supplement C to OET Bulletin 65
DE5468IP 3
Page 4
2.2 RF Section
Operating Frequencie s (MHz): 315 (in US A & Canada),
868.95, or other UH F channe l per l ocal requ irement in the
country of use.
Receiver Type: Super-heterodyne, fixed frequency
Receiver Range: 600 ft (180 m) in open space
Antenna Type: Spatial diversit y
Coding: PowerCode and/or CodeSecure™
2.3 Electrical Data
Power Supply: Internal switching power supply 100VAC
to 240VAC, 50/60 Hz, 0.5A / 12.5 VDC, 1.6A.
Current Drain: Approx. 40 mA standby, 1400 mA at full
load and in alarm.
Site External Siren Current (EXT): 450* mA max @ 10.5
VDC minimum when pow er ed by AC & DC (battery).
Site Internal Siren Current (INT): 450* mA max. @ 10.5
VDC minimum when powered by AC & DC (battery)
PGM Output Current: 100* mA max .
Detector 1 & 2 Total (Sum) Current : 36* mA max.
High Current / Short Circuit Protection: All outputs are
protected (automatic res et fu se).
* Total PowerMax Pro output current (of INT & EXT sirens,
PGM output and detectors) cannot exceed 550 mA.
Backup Battery Options:
Maximum external devices current
Backup
period
9.6V 1800 mAh
Battery Pack
1 battery
pack
(4)
2 battery
packs
(2)
9.6V 2200 mAh
Battery Pack
1 battery
(5)
pack
(1)
(3)
2 battery
(5)
packs
4h 240mA 400mA 300mA 300 mA
8h 100mA 200mA 140 mA 260 mA
12h 55mA 120mA 80 mA 160 mA
24h 0mA 40mA 25 mA 70 mA
36h (no
15mA 10 mA 36 mA
backup)
48h (no
3333.... INSTALLATION
INSTALLATION
INSTALLATION INSTALLATION
backup)
0mA 0 mA 18 mA
3.1 Unpacking the Equipment
Open the cardboard packing box and check whether all
items have bee n included. If you find out that an item is
missing, contact your vendor or dealer immediately.
3.2 Supplying Power to t he U nit
Enrolling the transmitting devices’ ID codes in the
PowerMax Pro memory will be easier if carried out before
actual installation, with all detectors and the control panel
on a work bench. It is therefore necessary to connect
power to the PowerMax Pro tempora rily (see figure 3.1G).
Alternatively, you may power up from the backup battery,
as shown in figure 3.1C.
Disregard any “trouble” indications pertaining to lack of
battery or lack of telephone line connection.
3.3 System Planning & Programming
It pays to p lan ahead - use t he t able s in app en dice s A and
B at the end of this g uide to reg ister the i ntended loc ation
of each detector, the holder and assignment of each
transmitte r and the control plan for the X-10 units.
The backup periods, when the PowerMax Pro includes
internal PowerLink with 1 active camera, GSM and
proximity reader, with external load connected between
+12 / V+ terminal and GND terminal, is as follows:
Battery Pack
type
9.6V 1800 mAh
Battery pack
Quantity
Backup
period
1 10h 30mA
external
(1)
load
2 20h 16 mA
9.6V 2200 mAh
1 12h 50 mA
2 24h 27 mA
1
Devices that are connected between +12 / V+
terminal and GND of Power Max Pro, tha t include s
internal GSM and proximi t y reader.
2
9.6V 1800 mAh, rechargeable Ni MH battery pack,
p/n GP180AAM8YMX, manufactured by GP.
3
9.6V 2200 mAh, rechargeable Ni MH battery pack,
p/n GP220AAH8B MX, manu factured by GP.
4
Standard / UL insta llation
5
Extended backup installation
Maximum battery recharge time: 72 hours
Battery Test: Once every 10 seconds.
2.4 Communication
Built-in Modem: 300 bau d, Bell 103 protocol
Data Transfer to Local Computer: Via RS232 seri al port
Report Destinations: 2 central stations, 4 private
telephones, 1 pager.
Reporting Format Opti ons: SIA, P ulse 4/2 1900/ 1400 Hz,
Pulse 4/2 1800/2300 Hz, Contact ID, Scancom.
Pulse Rate: 10, 20, 33 and 40 pps - programmable
Message to Private Phones: Tone or voice
."
Message to Pager: PIN No
Alarm Type "Zone No.
2.5 Physical Properties
Operating Temp. Range: 14°F to 120°F (-10°C to 49°C)
Storage Temp. Range: -4°F to 140°F (-20°C to 60°C)
Humidity: 85% relat ive humidity, @ 30°C (86°F)
Size: 10-13/16 x 8 x 2-1/8 in. (275 x 20 3 x 55 mm)
Weight: 990g (2.2 pound s) without batterie s
Color: Silver
Gather up all transmitters and detectors used in the
system and mark each one in accordance with your
deployment plan.
Program the system now as instructed in the
programming section.
3.4 Mounting
Required tool: Philips screwdriver #2.
PowerMax Pro mounti ng proc ess is s hown i n fi gure 3. 1A -
3.1H.
3.5 Wiring
Required tools: Cutter and slotted screwdriver - 3 mm
blade.
PowerMax Pro wiring is shown in figure 3.1B.
Extract the screw terminal blocks one by one and make
the necessary connections. When done, plug each
terminal block o nt o its PCB mounted pins .
4 DE5468IP
Page 5
1
Release
screws
2
Back unit
3
Mark 4 drilling points on mounting surface
Drill 4 holes and insert wall anchors
Figure 3.1A – Back Uni t Mounting
PHONE WIRING
1
Connect the receptacles of supplied flat cables
(2 - 5 cables according to options) to the back unit’s plugs.
4
The receptacles with strain relief clip are for the
front unit -
do not connect to the back unit!
Strain relief clip
Fasten the back unit with 4 screws
2
For all countries except north America:
Connect telephone cable to SET connector
and telephone line cable to LINE connector
(through the desired wiring cable entry).
5
3
Wiring in north America only
8-POSITION
RJ-31X PLUG
RED
GREEN
BROWN
GREY
RJ-31X
CORD
DE5468IP 5
RJ-31X JACK
23
1
RJ-31X
7
GRAY
RED
4
5
6
GRN
LINE
FROM
STREET
BROWN
HOUSE
PHONES
Page 6
ZONES & SIRENS WIRING
ZONE 29 /
ZONE 30 GND
TAMP
N.C.
Detector with
Tamper switch
Figure 3.1B - Wiring
Notes:
* Zone 29/GND and Zone 30/GND terminals can be
connected to a normally closed contac t of a detector,
switch (for example a Tamper switch of any device), or
Ω
a pushbutto n, via a 2.2 K
resistor. Such a resistor is
connected at the fac tory across both Zone 29/GND and
Zone 30/GND terminals. The resistors should remain
there if the terminals are not used. The V+ terminal
can be used to supply 12V (up to 36mA) to a detector
(if necessar y).
** Both +12V terminals are identical (s horted together).
The EXT terminal can be used to trigger an e xternal siren.
The INT terminal can be programmed for an "int ernal
siren" or "st robe" (see DEFINE OUTPUTS - DEFIN E
INT/STRB in par. 4.8).
The +12V and "GND" terminals can be c onnected to
a siren (for constant DC power supply) – not
applicable in North America.
*** The X-10 jumper sho uld be in 1-W p osition (for 1-way
power line interface unit) or in 2-W position (for 2-way
power line interface unit).
WARNING! When plugging terminals back into place, be
sure to align them carefully with the pins on the PCB.
Misaligned or rev erse insertion of termin als may damage
internal PowerMax Pro circuits!
IMPORTANT! The terminals for internal and external
sirens are DC o utpu ts i nte nde d for 12 V s iren s. Conne ct ing
a loudspeaker to any of these outputs will cause a short
circuit and wi ll damage the unit.
3.6 Backup Battery Insertion
Open batter y compartmen t cover (see figure 3.1C). Insert
one 8-battery pack and connect its connector to the
PowerMax Pro receptacle.
For optional two 8-battery packs: Insert both battery
packs and connect one battery pack connector to either
receptacles and the secon d battery pack connector to the
other receptacle.
ZONES
SITE
INTERNAL
SIREN OR
STROBE
SRN
+12VSRN
GND
PGM+12VGNDZONE30GND V+ZONE
V+
(*)
Regarding zones 29 & 30, the Control
Panel “sees” a specific resistance
according to the event, as foll ows:
Power
Normal (no alarm & no tamper): 2.2 kΩ
Alarm event: 4.4 kΩ
Tamper event: Infinite resis t a nce
29
CONNECT WIRED DETECTORS AS FOLLOWS:
Alarm
N.C.
Power
V+
(*)
ZONE 29 /
ZONE 30
2.2 k
Alarm
N.C.
Detector without
Tamper switch
Front
unit
Ω
INT
EXT
Note
SITE
EXT.
SIREN
Figure 3.1C - Battery Inse r tion
3.7 X-10 Interface Module Connection
Connect the X-10 interface module connector to the
PowerMax Pro receptacle. Route the cable through the
cable channel and connect to the X-10 interface module,
via the back unit.
To X-10 interface
module via
6-position
RJ-11 plug
the back unit
Cable
channel
Front
unit
Figure 3.1D - X-10 Interface Module Connection
3.8 Optional GSM Module Mounting
Plug in the GSM modu le and fasten it with the screw (see
drawing below).
Mount the optional GSM exter nal antenna on the desired
site surface and connect its connector to the PowerMax
Pro as shown below).
6 DE5468IP
Page 7
GSM
Front
unit
External GSM an tenna ca ble
Figure 3.1E - Optional GSM Module Mounting
3.9 Additional Optional Module Mounting
The GSM/PL/PC is a dual RS-232 Module that permits any
two simultaneous device connections such as: internal or
external Pow erLi nk , Lo ca l PC pr ogrammi ng, ex te rnal GSM
module.
Note: Connecti ng an internal and external GS M modules
simultaneously will disable both.
Note: The antenna(s) used for this transmitter must be
installed to prov ide a se paration di stanc e of at lea st 20 cm
from all persons and must not be co-located or operating
in conjuncti on with any other antenna or transmitter.
Press the GSM/PL/PC and AUDIO modules into the
marked locations (s ee f igure 3.1F) until a click is heard.
1. GSM/PL/PC module
(dual RS-232
module).
2. Audio Module
Note: The Audio
Module terminal strip
should be wired to the
external Voice Box
terminal strip,
according to the
12
Figure 3.1F - Other Optional Modules Mounting
3.10 Power Cable Connection
Connect the power cable and close the control panel as
shown in figure 3.1G.
Socket-outlet shall be installed near the equipment and
shall be easily accessible.
markings on bot h
terminal strips.
DE5468IP 7
Page 8
Thick cable entry:
desired wiring plastic cap (1
of 4).
Small wiring plastic cap for
thin cable entry
smaller section of the wiring
plastic cap and insert the
wiring plastic cap back into its
place.
Power cable clamp options
For thin
cable
Pull out a
: Break the
For thick cable
(reversed clamp)
Safety
cover
Power
supply
unit
(*)
Extract either of
these cable cl amps
for use in the next
step.
3
Enter power cable through the desired wiring channel (see step 1), route it to
the power supply unit and connect its 2 wires to the power supply terminal strip
with screwdriver. Fasten power cable by its clamp (see also step 2 - this clamp
can be reversed to fit thick/thin cable) and close the safety cover.
Figure 3.1G - Back Unit Power Cable Connection
* Do not route wirin g in this area, to enable proper closure of the control panel.
1
2
Power
supply
unit
(*)
4
OPTIONAL PLUG-IN POWER SUPPLY
Connect the power connector (optional) to the power
supply unit.
8 DE5468IP
Page 9
Front
unit
Back
unit
Connect the flat cables in their respective
1
connectors (2 - 5, according to options) .
2
Close the panel and
fasten the 2 screws.
Figure 3.1H - Final Clos ur e
3.11 Installing an Optional X-10 Siren
If you need a “wireless” external siren, you may install an X10 siren module which is triggered by a signal tr ansmitted
via the built-in electrical wiring of the protected site. This
siren can repla ce the regul ar ex ter nal si ren or complement it
without laying out additional wires. Of course , such a siren
can be used only in c onjunction w ith an opt ional po wer-line
interface module.
The X-10 siren is ready to function upon co nnection to an
electrical power outlet, without re-programming the
PowerMax Pro. You only have to set the HOUSE CODE
and the UNIT CODE selectors on the X-10 siren as follows:
House Code: Set this selector to the letter that follows, by
alphabetical order, the letter that you programmed as a
house code for the protec ted pr emis es . For ex ample , if the
programmed house code is “J”, set the siren house code
selector to “K”.
Note: If the programmed house code letter is “P” (wh i ch i s
the last programmable letter), select “A” for the siren.
Unit Code: The siren will function only if you set the unit
code selector to “1”.
3.12 Connecting to a Computer
The control panel ca n be equipped with an optional RS232
module for s erial data in terchange wit h a local computer. If
this modu le is not su pplie d, a s pecia l plas tic c ap bl ocks the
niche designed to accom m oda te the m od ule.
Pull out the plastic cap ( see figu re 3. 1I) . Inser t the RS-232
adapter and secure it with the screw. Break the smaller
section of the remo ve d plast ic cap an d insert it back into its
place.
Front Unit
Plastic
cap
Figure 3.1 I - Connecting to a Computer
3.13 Connecting to GSM Modem
The GSM unit enables the PowerMax Pro system to
operate over a cellula r network. For details regar ding the
GSM modem feature s and connections, refer to the GSM
Modem installation in st r uctions.
RS-232
adapter
RJ-45 or
RJ-31X
(USA)
DE5468IP 9
Page 10
4444.... PROGRAMMING
PROGRAMMING
PROGRAMMING PROGRAMMING
4.1 INTRODUCTION
4.1.1 General Guidance
We recommend to program the PowerMax Pro on the work
bench before actual installation. Operating power may be
obtained from the backup b attery or from the AC power supp ly.
The installer’s menu is accessible only to those who know
the installer’s 4-digit code, whic h is 9999 by factory default.
Note: Access to the installer menu, i n PowerMax Pro that
has "User Permission" enabled (for example in UK) is
accessible only at the en d of the user menu. This o ption can
be changed is necessary (see par. 4.4.36) .
For PowerMax Pro that has 2 installer codes (not
applicable in UK), the default INSTALLER code is 8888
and the default MASTER INSTALLER code is 9999.
The following actions can be done only by using the
master installer code:
• Changing master installer code.
• Resetting t he Pow erMax P ro parame ters t o th e de fa ul t
parameters,
• Defining specific communication parameters, as
detailed in a note in figure 4.5.
Obviously, you are expected to use this code only once for
gaining initial access, and replace it with a secret code
known only to yourself.
You will mainly use 5 control pushbuttons during the entire
programming process:
- to move one step forward in a menu.
- to move one step backward in a menu.
to enter the relevant menu or confirm data.
-
- to move one level up in a menu.
- to return to the "OK TO EXIT" state.
The sounds you will hear while programming are:
- Single beep , h eard whenev er a ke y i s pres sed .
- Double beep, indicates automati c return to the
normal operating mode (by timeout).
- Happy Melody (- - - –––), indicates successful
☺
completion of an oper at ion.
- Sad Melody (–––––), indicates a wrong move
$
or rejection.
4.1.2 Entering an Invalid Installer Code
If you enter an inval id installer code 5 times, the keypad
will be automatically disabled for 90 seconds and the
message WRONG PASSWORD will be displayed.
4.1.3 Installer’s Menu
The installer's menu is shown in figure 4.1a. The text in
rectangles represents the current PowerMax Pro display.
4.1.4 Setting a New I nstaller Code
To set an installer code, perform the actions that are
presented in f igure 4 .1b. When you are i nstructe d to enter
code, enter a 4-digit code.
4.1.5 Setting a New Installer Code in
PowerMax Pro that has 2 Installer
Codes
For PowerMax Pro with 2 installer codes, INSTALLER
code (default 8888) and MASTER INSTALLER code
(default 9999), set new codes as shown in figure 4.1c.
For details regarding the different authorization levels
when logging in with installer code and master installer
code, refer to the note inside f igure 4.5 (DEFINE COMM).
By using the master installer code, the menu enables
changing both master installer code and installer code.
By using the installer code, the menu enables changing
the installer cod e only.
10 DE5468IP
Page 11
(First disp lay is READY
or NOT READY)
READY 00:00
(See fig. 4.1a)
1. NEW INSTL CODE
NORMAL MODE
USER SETTING
INSTALLER MODE
ENTER CODE
[installer code]
1. NEW INSTL CODE
2. ENROLLING
3. DEFINE ZONES
4. DEFINE PANEL
5. DEFINE COMM.
6. DEFINE GSM
7. DEFINE PWRLNK
8. DEFINE OUTPUTS
9. DEFINE VOICE
10. DIAGNOSTICS
11. USER SETTINGS
12. FACTORY DEFLT
13. SERIAL NUMBER
14. START UL/DL
(*)
(See fig. 4.1b & 4.1c)
(See figure 4.2)
(See figure 4.3)
(See figure 4.4)
(See figure 4.5)
(See figure 4.6)
(See figure 4.7)
(See figure 4.8 )
(See figure 4.9)
(See figure 4.10)
(See chapter 7
in User Guide)
(See par. 4.12)
(Control Panel
serial number
display)
(See section 4.14)
NEW INST. CODE
INST. CODE xxxx
[code]
Figure 4.1b - Setting a New Inst a ller Code (see note)
By using
INSTALLER CODE
(see fig. 4.1a)
1. NEW INSTL CODE
NEW INST. CODE
INST. CODE xxxx
[code]
MASTER INSTALLER CODE
(see fig. 4.1a)
1. NEW INSTL CODE
NEW MASTER CODE
MASTER CODE xxxx
[code]
By using
NEW INST . CODE
INST. CODE xxxx
[code]
Figure 4.1c - Setting a New I nstaller Code
in System with Inst. & Master Inst. Codes (see note)
Note:
Installer
Code should never be programmed as
“0000”. Do ing s o will lock the user out of the installer menu!
<OK> TO EXIT
(*) Applicable only when "USER PERMIT" function is enabled
(see par. 4.4.36 - USER PERMIT)
Figure 4.1a - Installer’s Menu
4444....2 ENROLLING WIRELESS DEVICES AND KEYFOB TRANSMITTERS
2 ENROLLING WIRELESS DEVICES AND KEYFOB TRANSMITTERS
2 ENROLLING WIRELESS DEVICES AND KEYFOB TRANSMITTERS2 ENROLLING WIRELESS DEVICES AND KEYFOB TRANSMITTERS
4.2.1 General Guidance
The ENROLLING mode has 5 su b- mode s:
• ENROLLING TYPE (wi r e less devices)
• ENROLL WL (wireless devices) DEVICE
• ENROLL
• ENROLL WL 1WAY KP (wireless commander MC M-14 0+)
• ENROLL WL 2WAY KP (wireless 2-way keypa d MKP- 15 0)
• ENRO LL WL SIREN (wireless siren)
• ENRO LL PROX TAG (pr ox imity tag)
KEYFOB (mul ti-b utton CodeSecure trans mitters)
Before begi nning, gather all the devices that you intend to
enroll and make sure they all have batteries installed.
Your control panel must rec ogn ize the unique iden tif i c ati on
code (ID) of eac h such device i n order to supervise them,
receive their signal s and respond accord ingly.
Attention! CodeSecure transmitters are mainly used for
arming/dis arming and can no t be enrolled to zones. For
enrolling to zones, use only non-CodeSecure
wireless devices.
DE5468IP 11
Page 12
ENROLLING TYPE
ENROLL WL DEVICE
(*)
ENROLL KEYFOB
normal enroll
by tamper
(First display is READY
or NOT READY)
READY 00:00
NORMAL MODE
USER SETTINGS
INSTALLER MODE
ENTER CODE
[installer code]
1. NEW INSTL CODE
2. ENROLLING
3. DEFINE ZONES
4. DEFINE PANEL
5. DEFINE COMM
6. DEFINE GSM
7. DEFINE PWRLNK
8. DEFINE OUTPUTS
9. RECORD SPEECH
10. DIAGNOSTICS
11. USER SETTINGS
12. FACTORY DEFLT
13. SERIAL NUMBER
14. START UL/DL
<OK> TO EXIT
ZONE No: 05
TRANSMIT NOW
[Initiate transmission)
ZONE No: 05
for next
enrolling action
Enrolling a WL Device
1way kp No : 5 1way kp No : 5
TRANSMIT NOW
press
*
key until
red LED
lights
1way kp No: 5
for next
enrolling action
Enrolling a wireless
Commander MCM-140+
siren No : 2 siren No : 2
TRANSMIT NOW
Momentarily press the
wirel ess sire n self- test
button until a squawk is
heard (1 sec. approx.)
siren No: 2
for next
%
enrolling action
Enrolling a
wireless siren
SET SENSITIV.
higher sensitivity
lower sensitivity
Select by
or
%
ZONE No: - -
[Zone No.] (e.g. 05)
%
ZONE No: 05
<OFF> TO DELETE
(***)
(**)
ZONE No: 05
Deleting a WL Device
ENROL WL 1WAY KP
1way kp No :
[WL 1-way keypad
No. 1 to 8] (e.g. 5)
<OFF> TO DELETE
1way kp No: 5
Deleting a wireless
Commander MCM-140+
ENROL WL SIREN
%
SIREN No :
[WL siren No.
%
1 or 2] (e.g. 2)
Open WL
siren cover
and remove
its battery
<OFF> TO DELETE
Deleting a
wireless siren
(****)
siren No: 2
(**)
(**)
(**)
Keyfob No: -
[Keyfob No.]
(e.g. 5)
Keyfob No: 5
TRANSMIT NOW
(press any
key)
(**)
for next
enrolling action
Enrolling a Keyfob Deleting a Keyfob
ENROL WL 2WAY KP
%
2way kp No:
[MKP-150 No.
%
1 or 2] (e.g. 2)
2way kp No : 2 2way kp No : 2
Press MKP-150
back tamper
switch once
(see MKP-150
inst. instructions)
2way kp No: 2
for next
%
enrolling action
Enrolling a wireless
keypad MKP-150
(*)
Tag No: 5
PRESENT TAG
Present
tag
for next
enrolling action
Enrolling a Prox tag Deleting a prox tag
AWAY
ENROLL PR OX TAG
Tag No: -
(Prox tag No.)
(e.g. 5)
(**)
Figure 4.2 - Enrolling / Deleting Wireless Devices / Keyfobs / Wireless Commanders / Wireless Sirens
* Keyfob & proximity tags enro lling ca n be perform e d by the
installer or by th e user (v ia USER SETTIN GS menu ).
** Black box in the display means that a device is
enrolled (the syst em has learned its ID). No black box
indicates that the device is not enrolled.
*** Initiate either normal transmission or the device
tamper function (see ENROLLING TYPE, Par. 4.2.2).
**** Select "higher" sensitivity for far wireless device,
"lower" for near devices.
4.2.2 Enrolling Type
Here you determine whether to enroll a wireless device by
normal transmission or by device Tamper function
(opening its cover). Optio ns: normal, or by tamper.
4.2.3 Enroll/Delete Wireless Devices
Wireless devices include various PowerCode detectors
and hand-held trans mitt er s .
(**)
Keyfob No: 5
<OFF> TO DELETE
KEYFOB No: 05KEYFOB No: 05
(**)
<OFF> TO DELETETRANSMIT NOW
2way kp No: 2
Deleting a wireless
keypad MKP-150
(**)
Tag No: 5
<OFF> TO DELETE
Tag No: 05Tag No : 05
12 DE5468IP
Page 13
STOP
and dual-technology sensors should be
masked to preven t inad ver tent t ra nsmiss ion.
• Make sure that magnetic contact transmitters are
together with their magnets, to prevent them from
sending out alar m transmissions.
To enroll / delete wireless devices, refer to figure 4.2.
4.2.4 Enroll/Delete Keyfob Transmitters
• Before enrolling, the lens at the front of PIR
Keyfob tra nsmitters are multi-butt on wireless CodeSecure™
transmitters. Eight system users use them for better,
quicker and safer control over various system functions.
To enroll / d elet e 1-wa y or 2 -way k eyf ob tran smit ters , ref er
to figure 4.2.
4.2.5 Enroll/Delete Wireless Commander
The Wireless Commander (MCM-140+) is a remote control
unit that en ables the user to r emotely control the sys tem.
To enroll / delete up to 8 wireless commanders, refer to
figure 4.2 (Enroll WL 1-way KP).
4444....3 DEFINING ZONE TYPES, NAMES & CHIME ZO NE S
3 DEFINING ZONE TYPES, NAMES & CHIME ZO NE S
3 DEFINING ZONE TYPES, NAMES & CHIME ZO NE S3 DEFINING ZONE TYPES, NAMES & CHIME ZO NE S
This mode allows you to assign one of 13 zone types to
each of the system's 30 (wireless & wired) zones. In
addition, i t also allows you to assign a name to each zone
and determine whether the zone will operate as a chime
zone (only while the system is in the disarmed or Home
arming state). When a chime zone is triggered, chime
melody or zone na me is heard (there are 3 selectable chime
4.2.6 Enro l l /Delete 2 - W a y K eypad
The 2-way keypad, type MKP-150, enables the user to
remotely control the system and also to receive data fr om
the system (statu s, al arm and tro uble dat a). To enrol l up to
two 2-way keypads, refer to figure 4.2.
4.2.7 Enroll/Delete Wireless Siren
The wireless s iren is a remote si ren that is activat ed upon
predefined events by the PowerMax Pr o system. To enroll
/ delete up to 2 wireless sirens, refer to figure 4.2.
4.2.8 Enroll/Delete Proximity Tags
Proximity tags e nabl e auth orized p eopl e to en ter rest ric ted
areas. Presentin g valid proximity tag, while the system is
armed, causes the system to disarm. Presenting valid
proximity tag, while the system is disarmed, causes the
system to be armed i n AW AY (optional HOME) mode. To
enroll / delete proximity tags, refer to figure 4.2.
A list of factory defaults is printed on table 1. You may fill
out the blank columns even bef ore you start and pro ceed
to program according to your own list.
Remember!
A delay zone is als o a pe r imeter zone by de fin i tion.
Zone types are fully explained in Appendix D.
modes - Melody chime, Zone Na me Chime or Chime Off).
READY 00:00
NORMAL MODE
USER SETTINGS
INSTALLER MODE
ENTER CODE
[installer code]
ENROLLING
2.
3. DEFINE ZONES
(First display is READY
or NOT READY)
ZONE No
: - -
31 zone names can be selected, 26 fixed names and 5
custom names (defined by the insta lle r - see chap. 4.8):
Attic
Back door
Basement
Bathroom
Bedroom
Child room
Closet
Den
Selectable Z one Names
Dining room
Downstairs
Emergency
Fire
Front door
Garage
Garage door
Guest room
Hall
Kitchen
Laundry room
Living room
Master bath
Master bdrm
Office
Upstairs
Utility room
Yard
Custom 1
Custom 2
Custom 3
Custom 4
Custom 5
[Zone No.] (e.g. 05)
5.
DEFINE COMM
6.
DEFINE GSM
7.
DEFINE PWRLNK
8.
DEFINE OUTPUTS
9. DEFINE VOICE
10. DIAGNOSTICS
11. USER SETTINGS
12. FACTORY DEFLT
13. SERIAL NUMBER
14. START UL/DL
<OK> TO EXIT
Zxx: TYPE -
1. Inter-follow
2. Perimeter
3. Perim-follow
4. Delay 1
5. Delay 2
6. 24h silent
7. 24h audible
8. Fire
9. Non-alarm
10. Emergency
11. Gas
12. Flood
13. Interior
(*)
Zxx: NAME - -
Attic
Back door
Basement
Bathroom
Bedroom
Child room
Closet
(see list above)
(*)
Zxx: CHIME
Melody-chime
Zone name-chime
Chime off
(*)
(**)
Figure 4.3 - DEFINE ZONES Flow Chart
* The currently saved option is displayed with a dark box at the right side. To review the options, repeatedly click
or button, until the de sired opti on is disp layed, then cl ick (a dark box will be di splayed
at the right side).
** Clicking the
button in this location brings you to the same zone number that you are dealing with. Press
or to select the next zone.
DE5468IP 13
Page 14
Table 1 - DEFAULT AND PROGRAMMED ZONE DEFINITIONS
Zone Zone Type Zone Name Chime (melody
No. Default Programmed Default Programmed Zone Name or Off) (* )
1
Delay 1 Front Door
2
Delay 1 Garage
3
Delay 2 Garage Door
4
Perimeter Back Door
5
Perimeter Child Room
6
Interior Office
7
Interior Dining Room
8
Perimeter Dining Room
9
Perimeter Kitchen
10
Perimeter Living Room
11
Interior Living Room
12
Interior Bedroom
13
Perimeter Bedroom
14
Perimeter Guest Room
15
Interior Master Bedroom
16
Perimeter Master Bedroom
17
Perimeter Laundry Room
18
Perimeter Master Bathroom
19
Perimeter Basement
20
Fire Fire
21
Fire Fire
22
Emergency Emergency
23
Emergency Emergency
24
24 h / silent Baseme nt
25
24 h / silent Off ice
26
24 h / audible Attic
27
24 h / audible Den
28
non-alarm Yard
29
non-alarm Hall
30
non-alarm Utility room
* Note: All zones are Off-chime by default. Enter your own choice in the last column and pr ogr am accordingly.
4444....4 DEFINING CONTROL PANEL PARAMETERS
4 DEFINING CONTROL PANEL PARAMETERS
4 DEFINING CONTROL PANEL PARAMETERS4 DEFINING CONTROL PANEL PARAMETERS
4.4.1 Preliminary G uidance
This mode allow s you to customize the c ontrol panel and
adapt its c haracteristic s and behavior t o the requirements
of the particular user. An illustrated process is shown in
figure 4.4. In this illustration, each selected option is
displayed with a dark box at the right side. To review the
options, repeat edly click
the desired option is displayed, then click SHOW/OK button
4.4.2 Entry Delays 1&2
Two different entry delays allow the user to enter the
protected site (while the system is in the armed state) via 2
specifi c doors and routes without causing an alarm.
Following entry, the user must disarm the control panel
before the entry delay expires. Slow-rate warning beeps
start soundi ng once the door is opened , until the last 10
seconds of the delay, during which the beeping rate
increases. Locations No. 1 (entry delay 1) and 2 (entry
delay 2) allow you to program the length of these delays.
Available opti ons for each delay ar e:
60s
,
3m
and
4m
.
4.4.3 Exit Delay
An exit delay allows the user to arm the system and leave the
protected site via specific routes and doors without causing an
alarm. Slow-rate warning beeps start sounding once the
arming command has been given , until the la st 10 seco nds of
the delay, during which the beeping rate increases. Location
No. 3 allows programming of the exit delay length. Available
options are:
30s, 60s, 90s, 120s, 3m, 4m
(fig. 4.4 location 03)
or
(fig. 4.4, location 01, 02)
00s, 15s, 30s, 45s
button, until
.
4.4.4 Bell Time
Here you select the length of time the bell (or siren) is
allowed to function upo n alarm. The bell time st arts upon
activation of the siren. Once the bell time expires, the siren
is automatically shut down.
Available options are:
4.4.5 Abort Time
.
Here you select the l ength of time all owed by the system to
abort an alarm (not applicable to alarms from FIRE, 24H
SILENT, EMERGENCY, GAS and FLOOD zones). The
PowerMax Pro i s programmed to provide an “abort interval”
that starts upon detection of an event. During this in terval,
the buzzer sound s a warning but th e siren remains ina ctive
and the alarm is not reported. If the user disarms the system
within the allowed abort interval, the alarm is aborted.
Available options are:
4.4.6 Alarm Cancel
Here you determine the ”cancel alarm” period that starts
,
upon reporting an al arm to the central station. If the user
disarms the system within that time period, a “cancel
alarm” message is sent to the central station.
Available opti ons are:
also
cancel inactive
4.4.7 Quick Arm
Here you determine whether the user will be allowed to
perform quick arming or not. Once quick arming is
permitted, the co ntrol panel doe s not request a user code
before it arms the system.
The two options are:
(fig. 4.4, loca t i o n 04)
1, 3, 4, 8, 10, 15
(fig. 4.4 locat ion 05)
00s, 15s, 30s, 45s, 60s, 2m, 3m, 4m
(fig. 4.4, loc at i on 06)
1, 5, 15, 60 minutes, 4 hours
.
(fig. 4.4, location 07)
quick arm ON
and 20 minutes.
and
quick arm OFF
.
and
.
14 DE5468IP
Page 15
4.4.8 Bypass
Here you permit either manual bypassing of individual
zones (through t he USER SETTI NGS menu), or all ow the
system to "force arm" (perform automatic bypassing) of
open zones during the exit delay. If desired, press the
arming key twice i f you want to eliminate the del ay beeps
that continue during a force arming. If a zone is open and
forced arming is not permitted, “NOT READY” is displayed
and the system does not arm (the “Sad Melody” will
sound). If "no bypass" is selected, neither manual
bypassing nor for c e arming is allowed.
Options:
manual bypass, force arm
4.4.9 Exit Mode
Here you determine whether the exit delay will restart if the
exit / entry door is reopened bef ore the exit delay expir es.
Restarting the exit delay is helpful if the user re-enters
immediately after go ing out to retrieve an item that he lef t
behind. Three types of exit mode are available:
Restart Exit
reopened during exit delay. The restart occ u r s once only.
Off by door
automatically terminated (even if the defined exit delay
was not completed).
Normal
of whether the door is open or close d.
- Wh en the door is closed, the exit delay is
- The exit d elay is exactly a s defined, regardl ess
4.4.10 Piezo Beeps
Here you determine whethe r warning be eps will sound o r mut ed
during exit and entry delays. An additional option is to mute the
warning beeps only when t he syste m is ar med “HOME” .
Options:
enable beeps, off when home
4.4.11 Trouble Beeps
Under trouble conditions, the sounder emits a se ries of 3
short beeps onc e per minut e. Here you de termine whe ther
this special beeping se quence will be active, inacti ve, or
just inactive a t night (the range of “night” hours is defined
in the factory). The 3 options are:
(8 PM through 7 AM)
night
4.4.12 Panic Alarm
Here you determine whe ther the user will be allow ed to
initiate a panic ala rm by simultaneous pr essing ei ther the
two panic butto ns
or away + home
activates the siren and simultaneously transmits a
message via telephone. Silent panic only transmits a
message via telephone. The options are:
audible panic
4.4.13 Swinger Stop
Here you determine how many times each zone is allowed
to initiate a n alarm within a single arming period (including
tamper & power failure events of detectors, PowerMax Pro
and wireless siren). If the alarms number from a specific
zone exceeds the programmed number, the control panel
automatical ly bypasses the zone to prevent recurrent sir en
noise and nuisance reporting to the central station. The
zone will be reactivated upon disarming, or 48 hours after
having been bypassed (if the system remains armed).
Available options are:
after 3
and
no shutdown
4.4.14 Cross Zoning
Here you determine whether cross zoning will be active or
inactive. Cross zoning is a method used to counteract
false alarms - an alarm will not be initiated unless two
adjacent zones are viol ated within a 30-second time limit.
This featur e is active only when arming A WAY and only
with zone coupl es from zone No. 18 to 27
and 21, etc.). You may use any one of thes e zone couples
to create a “cross - z oned” area.
(fig. 4.4, location 08)
(fig. 4.4, location 09)
- Exit delay restarts when the door is
(fig. 4.4, location 10)
and
(fig. 4.4, location 12)
(on the keypad / wirel ess commander)
(on a keyfob trans mitter). Audible pani c
and
disable panic
(fig. 4.4, location 13)
shut after 1, shut after 2, shut
.
(fig. 4.4, location 14)
and
no bypass
and
disable beeps
(fig. 4.4, location 11)
enable beeps, off at
disable beeps
.
.
silent panic,
(18 and 19, 20
.
.
Note: If one of two crosse d zones is bypas sed (see Para.
4.4.8), the remaining zone will function independently.
Note: Ever y 2 c ross ed zones mu st be of the allo wed zone
type (Int e rior, Perimeter, Peri meter follower).
The options are:
Cross zoni ng is not app licable in E ntry/ Exit z ones and
24h zones (Fire, Emerg enc y , 24h au dibl e, 24 h sile nt ).
4.4.15 Supervision
Here you determine the time limit for reception of
supervision reports from various supervised wireless
devices. If any device does not rep ort at least once wit hin
the selected time limit, an “INACTIVITY” alert is initiated.
The options are:
4.4.16 NOT READY
Here you determine if the system will be NOT READY
status when there is a supervision failure. In the "in
supervision" mode, the system will be in NOT READY
status if during the l ast 20 minut es a s upervisi on messa ge
was not received. Opt ions:
4.4.17 AUX Button A
Here you select t he function of the AUX button on keyf ob
transmitters and wireless commanders MCM-140+. Four
options are of fered for each AU X button:
Status:
panel’s voice module to announce the system status.
Instant:
progress will cause the system to arm “instant” (the entry
delay is canceled).
Skip exit delay:
cause the syste m to arm “instant”.
PGM / X-10:
PGM output or X-10 units (see further programmin g under
“DEFINE OUTPUTS”, par. 4.8).
Pressing the AUX button will cause the control
Pressing the AUX button whi le the ex it delay is i n
4.4.18 AUX Button B 2-W-KF
location 18)
Same as 4.4.17 but for AUX button B.
4.4.19 Jam Detect
Here you determine whether jamming (interfering transmissions, on the radio channel used by the system) will be
detected and report ed or not.
If a jam detect ion option is selected, the sys tem does not
allow arming under the relevant jamming con d itions.
Option Detection and Reporting when
UL (20/20)
(USA standard)
EN (30/60)
(Europe standard)
class 6 (30/60)
(British standard)
Disabled
4.4.20 Latchkey
Here you determine whether t he system can be armed in
the latchkey mode. If the system is armed this way, a
“latchkey” message will be sent to specific telephones
upon disarming by a “latchkey user” (users 5-8 or k eyfob
transmitters 5-8). This mode is useful when parents at
work want to be i nformed of a child’s return from school.
You can reco rd a name for latchkey users.
The options are:
cross zone ON
1, 2, 4, 8, 12 hours
Pressing the AUX button will immediately
Pressing the AUX button will activate the
. Applicable only for 2-way keyfob MCT-237.
Jam Detection Options
There is continuo us 20 seconds of
jamming
There is an accumulated 30 seconds of
jamming within 60 sec.
Like EN (30/60) bu t the event will be
reported only if the jamming dur ati on
exceeds 5 minutes.
(no jamming detectio n and reporting).
Latchkey ON
and
cross zone OFF
(fig. 4.4, location 15)
and
disable
(fig. 4.4, loc ation 16)
normal
and
in supervision
(fig. 4.4, loc at i on 17)
(fig. 4.4, location 19)
(fig. 4.4, location 20)
and
Latchkey OFF
.
.
(fig. 4.4,
.
.
DE5468IP 15
Loading...