Visonic POWERMASTER 10 User Manual

Installer Guide
PowerMaster-10
Fully supervised wireless alarm control system
PowerMaster-10 Installer Guide
TABLE OF CONTENTS
1. INTRODUCTION .......................................................4
2. SPECIFICATIONS.....................................................4
3. INSTALLATION.........................................................6
3.1.1 Inserting Backup Battery .........................6
3.1.2 Connecting Power to Panel.....................7
3.1.3 Telephone Wiring......................................7
3.4.1 GSM Installation.........................................10
3.4.2 PowerLink Broadband Module
Installation .........................................................10
4. PROGRAMMING.....................................................11
4.2.1 Programming User Settings..................11
4.4.1 Setting a New Installer Code.................12
4.4.2 Setting the Master Installer Code.........13
4.4.3 Setting User Codes ................................ 14
4.4.4 Enabling User Permit for Installer
Access................................................................14
4.4.5 Configuring Permissions for System
Reset after Alarm Event ..................................14
4.4.6 Configuring a Duress Code................... 15
4.5.1 General Guidance ..................................16
4.5.2 Adding a Wireless Device..................... 16
4.5.3 Adding Wired Zones.............................. 20
4.5.4 Deleting a Device................................... 21
4.5.5 Modifying a Device ................................ 22
4.5.6 Replacing a Device................................ 23
4.5.7 Defining Defaults.................................... 24
4.6.1 Configuring the Length of Time the Bell
is allowed to Function...................................... 25
4.6.2 Enabling the Internal Siren ................... 25
4.6.3 Configuring the Period of Strobe Light
Activation .......................................................... 26
4.6.4 Enabling Siren Activation upon
Telephone Line Failure ................................... 26
4.7.1 General.................................................... 27
4.7.2 Setup Report Communicators.............. 27
4.7.3 Configuring Event Reporting to
Monitoring Station............................................ 30
4.7.4 Configuring Event Reporting to Users.39
4.8.1 Enable Cross Zoning............................. 42
4.8.2 Configuring Swinger Stop..................... 43
4.8.3 Enable Monitoring of Activity at Home 43
4.8.4 Configuring Alarm Cancel Period ........ 44
4.8.5 Configuring Power Failure Threshold
Period ................................................................ 44
4.8.6 Configuring Abort Time ......................... 45
4.8.7 Configuring a Confirmed Alarm............ 46
4.8.8 Enable Alarm upon Detection of
Jammed or Missing Device ............................ 46
4.8.9 Configuring the Jamming Detection .... 47
4.8.10 Configuring Whether a Missing Device Causes the System to Become "NOT READY"
............................................................................ 47
4.8.11 Configuring the Time Period by which a
Device is considered Missing......................... 48
4.9 Arming/Disarming Options And Exit/Entry
Delay ............................................................... 49
4.9.1 Configuring Exit Modes......................... 49
4.9.2 Configuring Entry Delays Duration...... 49
4.9.3 Configuring Exit Delay Duration........... 50
4.9.4 Enabling Quick Arm............................... 50
4.9.5 Configuring Bypassing Zones .............. 51
4.9.6 Configuring Panic Alarm Activation..... 52
D-302756 1
4.9.7 Enabling Latchkey Arming.................... 52
4.10.1 Enabling Trouble Beeps...................... 53
4.10.2 Enabling Piezo Beeps......................... 53
4.10.3 Enabling the Back Light ...................... 54
4.10.4 Configuring the Disarm Option........... 54
4.10.5 Configuring the Screen Saver Options
............................................................................ 55
4.10.6 Enabling the Memory Prompt............. 56
4.10.7 Enabling Keyfob Low Battery
Acknowledgement ........................................... 56
4.12.1 Preliminary Guidance.......................... 57
4.12.2 Define PGM .......................................... 58
4.13 Configuring Remote Programming Access
Permissions....................................................62
5 DIAGNOSTIC TEST ................................................ 64
5.1.1 Testing all Devices................................. 64
5.1.2 Testing One Device ............................... 65
5.1.3 Displaying Signal Strength Indication of
All Devices ........................................................ 66
5.1.4 Displaying Signal Strength Indication of
RF Devices ....................................................... 67
5.1.5 GPRS Communication Test ................. 67
5.1.6 LAN Connection Test ............................ 68
5.1.7 LAN Reset Option .................................. 69
6 CALLING UPLOAD/DOWNLOAD SERVER ....... 70
7. MAINTENANCE...................................................... 71
8 READING THE EVENT LOG..................................74
APPENDIX A. Detector Deployment & Transmitter
Assignments ............................................................... 75
APPENDIX B. Event Codes...................................... 77
B4. Understanding the Scancom Reporting
Protocol Data Format.................................... 79
APPENDIX C. Glossary............................................. 80
APPENDIX D. DEFAULT AND PROGRAMMED
ZONE DEFINITIONS................................................... 82
2 D-302756
MESSAGE TO THE INSTALLER
The PowerMaster-10 control panel is supplied with 3 instruction manuals:
Installer Guide (this manual - for your exclusive use) User’s Guide (for your use during installation only - Must be handed over to the master user after testing the
system) Accessories Guide (includes a full description of devices that are supported by the PowerMaster-10 system) Appendices A.1 and A.2 will help you prepare an installation plan. Please take time to fill out the forms - your job
will become much easier and confusion will be prevented. Filling out the forms will also help you create a list of detectors and transmitters that must be obtained for the particular application. Compatible detectors and transmitters are listed in the Accessories Guide.
Remember - it is advisable to power up the control panel temporarily after unpacking and program it on the work bench, in accordance with the installation plan.
Although setting the correct time and date is one of the user tasks, we recommend that you set the time and date in the course of programming. Access to the “User Settings” for the installer is possible through the installer‘s menu or through the user menu (see User’s Guide section 2).
After programming, proceed to install the system as detailed in the Installation Instructions, from paragraph 3.3 Mounting the Unit onward.
The installer should verify line seizure. Be aware of other phone line services such as DSL. If DSL service is present on the phone line, you must install a filter. It is suggested to use the DSL alarm filter model Z­A431PJ31X manufactured by Excelsus Technologies, or equivalent. This filter simply plugs into the RJ-31X jack and allows alarm reporting without breaking the internet connection.
D-302756 3
1. INTRODUCTION
The PowerMaster-10 is a user and installer-friendly, 29-zone fully-supervised wireless control system. The system is designed to function in an appealing way to the user and also offers features that make installers’
life easier than ever before:
EASY TO MAINTAIN
Alarm memory and trouble data are displayed upon request.
Diagnostic test provides visual and audible indication of the signal level of each detector.
Remote control from distant telephones.
Event log stores and displays information.
Upload / download from distant computer via telephone line or cellular modem.
QUICK PROGRAMMING
Simple programming logic, fully menu driven.
Multiple-choice selection of options for each parameter.
Unequivocal visual prompts.
Installer access to the user menu.
2. SPECIFICATIONS
2.1 Functional
Zones Number
Hardwired Zone Requirements
Zone Types
User Codes
Control Facilities
Display
Arming Modes
Alarm inhibited during a single arming period (swinger stop) after
Alarm Types
Siren Signals
Siren (bell) Timeout
Internal Sounder Output
Supervision
Special Functions
28 wireless zones, 1 hardwired input.
2.2 kΩ E.O.L. resistance (max. resistance of wires 220 Ω). Interior follower, interior, perimeter, perimeter follower, delay 1, delay 2,
home delay, interior-follow, interior, perimeter, perimeter-follow, 24h silent, 24h audible, emergency and non-alarm.
8 codes, 4 digits each (9999 different combinations). Code 0000 is not allowed.
- Integral keypad
- SMS commands via optional GSM/GPRS module.
- Remote control by telephone.
Note: For SIA CP-01 compliance, when using KF-234 PG2 an external siren must also be used.
Single line, backlit 16-character LCD. AWAY, HOME, AWAY-INSTANT, HOME-INSTANT, LATCHKEY,
FORCED, BYPASS. 1, 2, 3, alarm/tamper/fault, or not inhibited (programmable / selectable).
Note: To comply with EN requirements, the swinger stop should be set to
3.
Silent alarm, personal emergency alarm, burglary alarm and fire alarm. Continuous
pulse... (fire). Programmable (4 min. by default) At least 85 dBA at 10 ft (3 m) Programmable time frame for inactivity alert
- Chime zones
- Diagnostic test and event log.
- Local and Remote Programming over Telephone, GSM /GPRS connections.
- Calling for help by using an emergency transmitter.
- Tracking inactivity of elderly, physically handicapped and infirm people.
(intrusion / 24 hours / panic); triple pulse - pause - triple
4 D-302756
Data Retrieval
Real Time Clock (RTC)
Compliance with U.S. Standards:
Compliance with European CE Standards
GSM standards
2.2 Wireless
Frequency Band (MHz)
Antenna Type
Encryption
Protocol
Alarm memory, trouble, event log The control panel keeps and displays time and date. This feature is also used
for the log file by providing the date and time of each event USA: (FCC) CFR 47part 15 and part 68
Canada: RSS 210
The PowerMaster-10 is compatible with the RTTE requirements - Directive 1999/5/EC of the European Parliament and of the Council of 9 March 1999.
According to the European standard EN50131-1, the PowerMaster-10 security grading is 2 – "low to medium risk" and environmental classification is II – "indoor general" and the power supply type is A.
Europe: Complies with CE standards 3GPP TS 51.010-1, EN 301 511, EN301489-7
USA: CFR 47 Part 22 (GSM850) and Part 24 (GSM 1900). EMC standard: CFR 47 Part 15.
Europe: 433, 868, USA: 915. Spatial diversity AES-128 PowerG
2.3 Electrical
External AC/AC adapter Europe: 230VAC 50Hz input, 9VAC 700mA output.
USA: 120VAC 60Hz input, 9VAC 1000mA output.
Current Drain Approx. 70 mA standby, 1600 mA peak at full load.
Minimum battery voltage
Backup Battery Pack
Backup Battery Pack
Battery Test
4.8V Note: For CE compliance the battery backup period shall exceed 12 hours.
4.8V 1300 mAh, rechargeable NiMH battery pack, p/n GP130AAM4YMX, manufactured by GP or equivalent
Note: For compliance with UL standards the battery backup period shall exceed 24 hours.
4.8V 2200 mAh, rechargeable NiMH battery pack, p/n GP230AAHC4YMX, manufactured by GP
Once every 10 seconds
2.4 Communication
Built-in Modem
Data Transfer to Local Computer
Report Destinations
Reporting Format Options
Pulse Rate
Message to Private Phones
300 baud, Bell 103 protocol Via RS232 serial port
2 Monitoring Stations, 4 private telephones SIA, Pulse 4/2 1900/1400 Hz, Pulse 4/2 1800/2300 Hz, Contact ID,
Scancom. 10, 20, 33 and 40 pps - programmable Tone
D-302756 5
Ring Detection
The unit does not support ring detection without DC voltage present on the telephone lines.
2.5 Physical Properties
Operating Temp. Range
Storage Temp. Range
Humidity
Size
Weight
Color
14°F to 120°F (-10°C to 49°C)
-4°F to 140°F (-20°C to 60°C) 85% relative humidity, @ 30°C (86°F) 196 x 180 x 55 mm (7-5/8 x 7 x 2 in.) 658g (23 Oz) (with battery) White
3. INSTALLATION
Note: This system must be checked by a qualified technician at least once every three (3) years.
3.1 Supplying Power to the Unit
Connect power to the PowerMaster-10 temporarily (see Figure 3.2). Alternatively, you may power up from the backup battery, as shown in Figure 3.1. Disregard any “trouble” indications pertaining to lack of battery or lack of telephone line connection.
For Europe Safety Compliance:
a. The model shall be installed according to the local electrical code. b. The circuit breaker shall be readily accessible. c. The rating of the external circuit breaker shall be 16A or less. d. The cables for the AC mains connection shall have an overall diameter of 13mm and 16mm conduit. Please refer to Figure 3.2 "Power Cable Connection".
3.1.1 Inserting Backup Battery
Connect battery pack as shown in the next drawing.
1
2
1. Battery insertion
2. Battery connection
Figure 3.1 – Connecting Battery
6 D-302756
3.1.2 Connecting Power to Panel
Connect the power cable and close the control panel as shown below. Electrical socket-outlet shall be installed near the equipment and shall be easily accessible.
WARNING! DO NOT USE AN OUTLET CONTROLLED BY A WALL SWITCH.
Note: This equipment should be installed in accordance with Chapter 2 of the National Fire Alarm Code, ANSI/NFPA
72, (National Fire Protection Association).
Connect the power adapter to the power connector.
Fig. 3.2 - Power Cable Connection
3.1.3 Telephone Wiring
PHONE WIRING
Connect the telephone cable to the SET connector and connect the telephone line cable to the LINE connector
(through the desired wiring cable entry). Note: The telephone cable should be no longer than 3 meters.
C
B
A
A. SET B. LINE C. Tel line wall jack
PHONE WIRING IN NORTH AMERICA
B
A
C
1
I
23
RJ-31X
7
6
F
4
5
G
D
E
F
G
H
D-302756 7
E
J K
H
A. SET B. LINE C. RJ-31X cord D. 8-position RJ-31X plug E. Gray F. Red G. Green H. Brown I. RJ-31X jack J. Line from street K. House phones
This equipment is designed to be connected to the telephone network using RJ11 connector which complies with Part 68 rules and requirements adopted by ACTA and properly installed RJ31X connector. See drawing below for details.
Customer Premises Equipment And Wiring
In the case that RJ31X is not available (consult your telephone company or a qualified installer), the telephone line should be connected to the PowerMaster-10 unit first and then all other home equipment should be connected to PowerMaster-10 "Phone" outlet.
D
A
F
H
J
B
E
C
E
I
H
G
E
A. Network Service Provider's Facilities B. Telephone Line C. Network Demarcation Point D. RJ-31X Jack E. Telephone F. Alarm Dialing Equipment G. Answering System H. Unused RJ-11 Jack I. Fax Machine J. Computer
Note: The REN is used to determine the number of devices that may be connected to a telephone line. Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the local telephone company.
Connection to telephone company provided coin service is prohibited. Connection to party lines service is subject to state tariffs.
3.2 System Planning & Programming
It pays to plan ahead - use the tables in appendices A and B at the end of this guide to register the intended location of each detector, the holder and assignment of each transmitter.
8 D-302756
Gather up all transmitters and detectors used in the system and mark each one in accordance with your deployment plan.
Program the system now, before mounting, as instructed in the programming section.
3.3 Mounting the Unit
Required tool: Philips screwdriver #2. PowerMaster-10 mounting process is shown in Figure 3.3 - 3.4.
A
B
1
3
A
4
A. Mounting surface B. Back unit To Mount the Unit:
1. Release the screws
2. Remove the front cover
3. Mark 4 drilling points on the mounting surface
4. Drill 4 holes and insert wall anchors
5. Fasten the back unit with 4 screws
Figure 3.3 – Back Unit Mounting
WARNING! When plugging SIREN & ZONE terminals back into place, be sure to align them carefully with the
pins on the PCB. Misaligned or reverse insertion of terminals may damage internal PowerMaster-10 circuits!
A
5
D-302756 9
3.4 Extension Modules Installation
3.4.1 GSM Installation
The internal GSM 350 module enables the PowerMaster-10 system to operate over a GSM/GPRS cellular network (for further details, see the GSM 350 PG2 Installation Instructions). The GSM modem auto detection feature enables automatic enrollment of the GSM modem into the PowerMaster-10 control panel memory. GSM modem auto detection is activated in one of two ways: after tamper restore and after reset (power-up or after exiting the installer menu). This causes the PowerMaster-10 to automatically scan GSM COM ports for the presence of the GSM modem.
In the event that the GSM modem auto detection fails and the modem was previously enrolled in the PowerMaster-10.
G2 control panel, the message "Cel Rmvd Cnfrm" will be displayed. This message will disappear from the display only after the user presses the
GSM trouble message will be displayed. Note: A message is displayed only when the PowerMaster-10 alarm system is disarmed.
3.4.2 PowerLink Broadband Module Installation
The PowerLink broadband module enables viewing the PowerMaster-10 system over the internet (for further details, see the PLINK PRO Installation Instructions).
The PowerLink Broadband Module modem auto detection feature enables automatic enrollment of the PowerLink Broadband Module modem into the PowerMaster-10 control panel memory. The PowerLink Broadband Module modem auto detection is activated in one of two ways: after tamper restore and after reset (power-up or after exiting the installer menu). This causes the PowerMaster-10 to automatically scan the PowerLink Broadband Module COM ports for the presence of the PowerLink Broadband Module modem.
In the event that the PowerLink Broadband Module modem auto detection fails and the modem was previously enrolled in the PowerMaster-10 control panel, the message "PLNK Remvd Cnfrm" will be displayed. This message will
disappear from the display only after the user presses the enrolled and no PowerLink Broadband Module trouble message will be displayed.
Notes: A message is displayed only when the PowerMaster-10 alarm system is disarmed. In the event of a power failure the PowerLink Broadband Module will not operate. Power (AC or battery) must be disconnected from the circuit before connecting / disconnecting the PowerLink Broadband Module.
button. The modem is then considered as not enrolled and no
button. The modem is then considered as not
3.5 Closing the Control Panel
Control panel final closure is shown below.
1
To Close the Control Panel:
1. Close the front cover
2. Fasten the screws
Figure 3.4 - Final Closure
10 D-302756
4. PROGRAMMING
U
Z
N
R
4.1 General Guidance
We recommend programming the PowerMaster-10 on the work bench before actual installation. Operating power may be obtained from the backup battery or from the AC power supply.
4.2 Entering the Installer Menu
The following procedure describes how to enter the Installer Menu.
To Enter the Installer Menu
1.
2.
3.
4.
EADY 00:00
INSTALLER MODE
ENTER CODE: 
CODE Enter your Installer Code.
EW INSTL CODE
or Press the or button repeatedly until the display reads the
ONES DEVICES
Make sure the system is disarmed and then press the button repeatedly until the PowerMaster-10 display reads "INSTALLER MODE".
desired setting option, for example, "ZONES/DEVICES".
You can program any other menu or press the or buttons to take you to "
<OK> TO EXIT
".
4.2.1 Programming User Settings
This mode provides you with a gateway to the user functions through the regular user programming menu.
To Enter the User Settings Menu
1.
2.
Caution! If after having programmed the user codes the system does not recognize your installer code, this indicates you must have programmed a user code that is identical with your installer code. If so, access the user menu and change the code that is identical with your installer code. This will re-validate your installer code.
D-302756 11
SER SETTINGS
Repeat steps 1 to 4 of section 4.2 "Entering the Installer Menu".
Refer to the PowerMaster-10 User Guide for detailed procedures Clicking the or buttons at any stage in the procedure will take you to “
<OK> TO EXIT
”.
4.3 Navigation
This mode allows you to customize the control panel and adapt its characteristics and behavior to the requirements of the particular user. To review the options within the control panel menus, repeatedly press the
You will mainly use 5 control pushbuttons during the entire programming process:
The sounds you will hear while programming are:
- Single beep, heard whenever a key is pressed.
If you enter an invalid installer code 5 times, the keypad will be automatically disabled for 90 seconds and the message WRONG PASSWORD will be displayed.
button, until the desired option is displayed, then press the button.
- to move one step forward in a menu.
- to move one step backward in a menu.
to enter the relevant menu or confirm data.
-
- to move one level up in a menu.
- to return to the "OK TO EXIT" state.
- Double beep, indicates automatic return to the normal operating mode (by timeout).
- Happy Melody (- - - –––), indicates successful completion of an operation.
- Sad Melody (–––––), indicates a wrong move or rejection.
or
4.4 Permissions and User Codes
The PowerMaster-10 system includes four code levels, as follows:
• Installer Code: By using the installer code, the menu enables changing the installer code.
Master Installer Code: By using the master installer code, the menu enables changing both master installer
code and installer code.
User Code: See PowerMaster-10 User Guide
• Master User Code: See PowerMaster-10 User Guide
Not every system includes a MASTER INSTALLER code. In a system with an INSTALLER code only, the installer can use all the functions in the system. The following actions can be done only by using the master installer code:
Changing master installer code.
Resetting the PowerMaster-10 parameters to the default parameters,
Defining specific communication parameters.
You are expected to use this code only once for gaining initial access, and replace it with a secret code known only to yourself.
4.4.1 Setting a New Installer Code
To set an installer code, perform the actions that are presented below. When you are instructed to enter code, enter a 4-digit code.
A. To Set a New Installer Code
1.
2.
NEW INSTL CODE
Repeat steps 1 to 4 of section 4.2 "Entering the Installer Menu".
3.
4.
12 D-302756
NEW MASTER CODE
NEW INST. CODE
Note: The menu displayed within the dashed box appears only if the control panel includes the Master Installer Code.
M
9
8
5.
Note: Installer Code should never be programmed as “0000”. Doing so will lock the user out of the installer menu!
INST. CODE
NEW INST. CODE
88
Enter the new 4-digit Installer Code (8888 or 9999) at the position of the blinking cursor and then press
* The default Installer Code is 9999.
If your system uses MASTER CODE, you should proceed to setting the MASTER INSTALLER code in section 4.4.2 by pressing the button, or press the button to take you to "
.*
<OK> TO EXIT
".
4.4.2 Setting the Master Installer Code
For PowerMaster-10 with MASTER INSTALLER code, set a new INSTALLER code as described in section
4.3.1 "Setting a New Installer Code" and set the MASTER INSTALLER code as described in this section.
Note: For Control Panel that has installer code & master installer code, the following functions are available only if the MASTER INSTALLER code is entered:
PSTN/GSM RCVR1
RCVR 1 ACCOUNT#
PSTN/GSM RCVR2
RCVR 2 ACCOUNT#
PSTN RPRT FORMAT
4/2 PLS RATE
REPORT EVENTS
RPRT CNFRM ALRM
SEND 2WV CODE
VOICE Monitoring Station.
RINGBACK TIME
PSTN RPRT RETRY
GSM RPRT RETRY
MAST. DL CODE
By using the master installer code, the menu enables changing both master installer code and installer code. By using the installer code, the menu enables changing the installer code only.
B. To Set a New Master Installer Code
1.
2.
NEW INSTL CODE
Repeat steps 1 to 4 of section 4.2 "Entering the Installer Menu".
3.
D-302756 13
NEW MASTER CODE
ASTER CODE
NEW MASTER CODE
Enter the new 4-digit Installer Code (8888 or 9999) at the position of the
99
blinking cursor and then press
* Master Installer Code should never be programmed as “0000”. Doing so will lock the user out of the installer menu!
You can now press the button to set the INSTALLER code or press the
button to take you to "
<OK> TO EXIT
.*
".
3
0
3
D
4.4.3 Setting User Codes
For detailed instructions on setting user codes, refer to the PowerMaster-10 user guide "Menus and Functions".
4.4.4 Enabling User Permit for Installer Access
User Permission enables you to determine whether access to the INSTALLER MODE requires user permission. Access to the installer menu, in PowerMaster-10 that has "User Permission" enabled (for example, in UK) is via the last menu in the user menu. This option can be changed, if necessary. Here you determine whether the access to the INSTALLER MODE requires user permission. If you select ENABLE, the installer mode will be accessible only through the user menu after entering the user code.
Options: Enable (default in UK), Disable (default).
Note: To comply with EN requirements, "Enable" must be selected.
To Enable User Permit for Installer Access
1.
2.
3.
4.
5.
DEFINE PANEL
1:ENTRY DELAY 1
or
6:USER PERMIT
isable
6:USER PERMIT
Repeat steps 1 to 4 of section 4.2 "Entering the Installer Menu".
Select between "Disable" (default) and "Enable".
You can now press the or button to program any other menu in "
DEFINE PANEL
" or press the button to take you to "
<OK> TO EXIT
".
4.4.5 Configuring Permissions for System Reset after Alarm Event
(Not applicable in the USA)
Here you determine whether the system can be rearmed (after an event) by the user or only by the installer. Options: user reset (default), engineer reset, or anti code reset. If Engineer Reset is selected, the system can be rearmed only by the installer; by entering and exiting the installer menu, by entering and exiting the event log (see section 8), or by remote telephone. To perform Engineer Reset via the telephone, establish communication with the PowerMaster-10 (see user guide, Chapter 5) and continue as follows: a. "*", "installer code", "#" b. Wait for 2 beeps c. "*", "1", "#" d. "*", "99", "#"
Visonic uses Technistore anti code reset. Installers should check with their Monitoring Station for a code version (seed code) which needs to be entered.
14 D-302756
To Configure Permissions for System Reset after an Alarm Event
0
2
2
D
2
0
2
u
1.
2.
3.
4.
5.
DEFINE PANEL
1:ENTRY DELAY 1
or
5:RESET OPTION
ser reset
5:RESET OPTION
Repeat steps 1 to 4 of section 4.2 "Entering the Installer Menu".
Select between "user reset" (default), "engineer reset" and "anti code reset".
You can now press the or button to program any other menu in "
DEFINE PANEL
" or press the button to take you to "
<OK> TO EXIT
".
4.4.6 Configuring a Duress Code
A duress alarm (ambush) message can be sent to the Monitoring Station if the user is forced to disarm the system under violence or menace. To initiate a duress message, the user must disarm the system with the duress code (2580 by default). Here you can change the code digits or enter "0000" to disable the duress feature. The system
does not allow the user to program the duress code saved in this memory location as an existing user code.
Note: Duress Code is not applicable in the UK.
To Configure a Duress Code
1.
2.
3.
4.
5.
1:ENTRY DELAY 1
URESS CODE 2580
DEFINE PANEL
or
3:DURESS
3:DURESS
Repeat steps 1 to 4 of section 4.2 "Entering the Installer Menu".
Change the code or enter 0000 to disable the duress function.
You can now press the or button to program any other menu in "
DEFINE PANEL
" or press the button to take you to "
<OK> TO EXIT
".
D-302756 15
4.5 Zones / Devices
4.5.1 General Guidance
The ZONES / DEVICES mode enables the following functions:
- Defining default parameters common for each devices family.
- Adding new devices (enrolling) and defining their zones name, zone type and chime zone.
- Deleting devices.
- Modifying devices parameters.
- Reviewing devices parameters. Enrolling can be performed for Keyfobs (multi-button), wireless detectors, wireless sirens and repeaters. The control panel enables entering a device identification (ID) instead of enrolling an actual device. This enables pre-
enrolling off site. Upon boot up, the control panel checks if there are pre-enrolled devices that have not yet been registered (ID of the devices are entered but the devices have not communicated with the control panel). In this case, the control panel will display "SYNC WITH DEV" on the LCD and the trouble LED will be on until all the devices have registered or the pre­enrolled devices that have not registered will be deleted from the enrollment menu.
Refer to sections 4.4.3 and 4.4.4 for detailed instructions on Enrolling/Deleting a device.
Notes
- Keyfob enrolling can be performed also by the user (via USER SETTINGS menu).
- Wired magnetic contact or any other contact can be enrolled in zones 29 & 30.
- Wireless detectors can be enrolled in zones 01-28. Before beginning, gather all the devices that you intend to enroll and make sure they all have batteries installed.
Your control panel must recognize the unique identification code (ID) of each such detector in order to supervise them, receive their signals and respond accordingly.
Before enrolling, the lens at the front of PIR and dual-technology sensors should be masked to prevent inadvertent
transmission.
Make sure that magnetic contact transmitters are together with their magnets, to prevent them from sending
out alarm transmissions.
4.5.2 Adding a Wireless Device
This section describes how to add a new device to the PowerMaster-10 control panel. Note: It is much easier to enroll the device while holding the device in your hand, close to the control panel.
A. To Add a Device
1.
2.
3.
4.
5.
16 D-302756
ZONES/DEVICES
ADD NEW DEVICES
ENROLL NOW or
ENTR ID: XXX-XXXX
Repeat steps 1 to 4 of section 4.2 "Entering the Installer Menu".
You are now instructed to enroll the device. Enter the 7-digit number printed on the back side of the device and press
or Perform the enrollment sequence for the specific device: For most devices: Remove the device bracket or cover and press the
device's Enroll button continuously until the red & green LEDs turn ON and then release. The PowerMaster-10 will indicate the result on its LCD display.
For Keyfobs: Press the '*' button until the red LED blinks rapidly and then release (the LED will continue blinking) then press the same button again. The LED lights green and the PowerMaster-10 will indicate the result on its LCD display.
.*
DEVICE ENROLLED
Z01:Motion Sens
K01:Keyfob
………..
S01:Siren
The PowerMaster-10 display reads "
accepted
and the PowerMaster-10 display will then change to "
" if the device was enrolled manually by entering the ID number)
Z01:Motion Sens / S01:Siren
device". However, if the device was previously enrolled in the system, the
PowerMaster-10 display reads " Repeat the above procedure for each device to be enrolled in the
PowerMaster-10 system. Continue to section 4.4.2.1 Assigning a Location, Zone Type and Chime Option. When exiting " displays the number of devices that need to be updated, as follows: DEV UPDATING NNN. * If you enter the 7-digit number, you must physically install the device
to complete the procedure. If the device is not installed, the system will display the device as "
networked). You can now press the button to enroll the next device of the same type or press the button to move to the " section 4.4.2.1) or press the button to take you to "
ZONES / DEVICES
ALREADY ENROLLED
NOT NET
DEVICE ENROLLED
" (or "
K01:Keyfob /
depending on the type of enrolled
".
" menu the PowerMaster-10 system
" (device is pre-enrolled – not
LOCATION
" menu (see
<OK> TO EXIT
ID
".
4.5.2.1 Assigning a Location, Zone type and Chime Option
B. To Assign a Location, Zone Type and Chime Option
The PowerMaster-10 system behavior is defined according to one of 11 zone types assigned to each of the system's 30 (wireless & wired) zones.
Note: This step is applicable to detectors only.
Continue below from the previous section.
1.
2.
3.
4.
5.
D-302756 17
Z01:LOCATION
Front door
or
Master Bdrm
Z01:ZONE TYPE
12.Non-Alarm
or
Select a zone type, or, enter the zone type number, for example, pressing 03 selects "3. Home Delay".
6.
7.
8.
9.
10.
11.
12.
3.Home Delay
Z01:SET CHIME
Chime off….
or
melody-chime
Z01:DEV SETTINGS
NEXT device
MODIFY SAME Dev.
EXIT Enrollment
To understand the behavior of each zone, see section 4.5.2.3 Zone Types.
Press
Select between "Chime off" and "melody-chime".
Note: In "melody chime" mode when a chime zone is triggered, chime melody is heard.
*
*
*
* When the PowerMaster-10 will read "
"
MODIFY SAME Dev.
device. When the PowerMaster-10 will read " click the button to revert to "
to change chime settings or press the button to skip.
NEXT device
button to enroll the next device. When the PowerMaster-10 will read
" you can click the button to modify the same
" you can click the
EXIT Enrollment
ADD NEW DEVICES
".
" you can
4.5.2.2 Configuring Device Parameters
Refer to the PowerMaster-10 Accessories Guide for detailed instructions on how to modify specific device settings for each device
4.5.2.3 Zone Types
Upon enrollment of a new detector (marked "Zxx") you must select the proper zone type. The zone type determines how the system handles alarms and other signals sent from the device. A list of factory defaults is printed in Appendix D. You may fill out the blank columns even before you start and proceed to program according to your own list.
Zone types are fully explained below: Delay Zones:
A delay zone has exit and entry delays set by you in the course of programming the system. Warning beeps will sound throughout these delays, unless you choose to mute them.
Exit Delay - The exit delay begins once the user arms the system. It allows him to leave via interior zones and a doorway before arming actually takes effect. When the exit delay starts, the buzzer beeps slowly and maintains a slow beeping rate until the last 10 seconds, during which it beeps rapidly. The PowerMaster-10 has two types of delay zones, for which different delay times may be set.
Entry Delay - The entry delay begins once the user enters the protected area via a specific doorway (his entry is sensed by a delay zone detector). To avoid an alarm, he must reach the keypad via interior zones (which become "follower zones" during the entry delay) and disarm the system before the delay expires. When the entry delay starts, the buzzer beeps slowly until the last 10 seconds, during which it beeps rapidly.
Remember!
A delay zone is also a perimeter zone by definition.
18 D-302756
Emergency Zones:
You can provide incapacitated, sick or elderly people with a miniature single-button transmitter to be carried on the neck like a pendant or to be worn on the wrist like a watch. In distress situations, they can press the button on their transmitter, causing the PowerMaster-10 to send an emergency call to the Monitoring Station or to private telephones designated by the installer.
To make this possible, define the required number of zones as emergency zones and enroll a portable transmitter to each one of these zones. When completed, ask the master user to distribute these transmitters to their potential users.
Interior Zone:
Interior zones are zones within the protected premises that have nothing to do with perimeter protection. Their most important feature is that they allow free movement within the protected area without initiating an alarm, provided that the system is armed in the "HOME" mode. People can therefore stay at home and move about freely, as long as they do not disturb a PERIMETER zone. Once the system is armed in the AWAY mode (all zones are protected), interior zones will initiate an alarm if violated.
Interior Follower Zones:
"Interior Follower" zone is a zone that is located between entry/exit zone and the alarm system control panel. This zone is temporarily (without causing an alarm) in front of a motion detector that is associated with the Interior Follower zone, after you enter through an entry zone on the way to the control panel, or when leaving the protected premises after system arming.
Home/Delay Zones:
A zone type which functions as a delay zone when the system is armed HOME and as a perimeter-follower zone when the system is armed AWAY.
Non-Alarm Zones:
A non-alarm zone does not directly participate in the alarm system. It can be used for chime or for optional KEY ON-OFF feature (when enabled). You can define the desired number of non-alarm zones and enroll a portable transmitter or a wireless device (detector) to this type of zone.
Perimeter Zones:
Perimeter zones rely on detectors designed to protect doors, windows and walls. An immediate alarm is initiated when such a zone is violated by opening the door/window or by trying to break the wall.
Perimeter Follower Zones:
A non-entry/exit zone, typically a perimeter zone located on an entry/exit path, that is treated as an entry/exit zone during an entry/exit time.
24-Hour Zones:
24 hour zones are mainly used for PANIC buttons, perimeter detectors and anti-tamper protection. They therefore trigger an alarm in both armed and disarmed states.
24 Hour Zone - Silent. - Upon detection, this zone initiates a silent alarm, meaning that the sirens do not function. Instead the PowerMaster-10 dials telephone numbers and reports the event to Monitoring Stations and/or to private telephones, as programmed.
24 Hour Zone - Audible. - Upon detection, this zone initiates a siren alarm. The PowerMaster-10 also dials telephone numbers and reports the event to Monitoring Stations and/or to private telephones, as programmed.
ignored by the alarm system during entry/exit delay periods, to enable you to walk
4.5.2.4 Locations
You can select or assign a named location to a device (e.g. Garage, Front Door etc.). 31 locations can be selected, 26 fixed names and 5 custom names (defined by the installer).
Note: Custom Locations can be defined via the DEFINE CUSTOM menu, and these custom names will also appear on your location list in addition to the default names. Note: To facilitate assigning a location name to a device, a shortcut procedure may be used by entering the location number which takes you directly to the location name.
Selectable Locations:
Attic Back door Basement Bathroom Bedroom
D-302756 19
Child room Closet (UK: Conservatory) Den (UK: Playroom) Dining room Downstairs Emergency Fire Front door Garage Garage door Guest room Hall Kitchen Laundry room Living room Master bath Master bdrm Office (UK: Study) Upstairs Utility room Yard (UK: Garden) Custom 1 Custom 2 Custom 3 Custom 4 Custom 5
4.5.3 Adding Wired Zones
Required tools: Cutter and slotted screwdriver - 3 mm blade. PowerMaster-10 wiring is shown in Figure 4.1.
CABLES ROUTING GUIDE
A
C
B
A. Cables entry options B. Back unit C. Cable clips To Route the Cable:
1. Remove the left or right side cables entry knockout(s) and enter the required cable(s)
2. Remove and use as cable clamp(s)
20 D-302756
1 2
ZONE WIRING
B
A. ZONE B. TAMPER C. ALARM
Note: Do not use mains cable other than that supplied by the manufacturer (3 m long).
Figure 4.1 - Wiring
2.2k
C
A
2.2k
Ω
Ω
4.5.4 Deleting a Device
C. To Delete a Device
1.
2.
3.
4.
5.
6.
D-302756 21
ADD NEW DEVICES
DELETE DEVICES
CONTACT SENSORS
MOTION SENSORS
Z01:Motion Sens
Z03:Motion Sens
or
or
Repeat steps 1 to 3 in section 4.5.2 "Adding a Wireless Device".
Select the type of device to be deleted. Select between "CONTACT SENSORS", "MOTION SENSORS", "SMOKE SENSORS", "WIRED SENSORS", "KEYFOBS", "SIRENS" and "REPEATERS" for example, "MOTION SENSORS".
Select the motion sensor to be deleted, for example, "Z03:Motion Sens".
7.
8.
(OFF) to delete
MOTION SENSORS
The device is deleted from the PowerMaster-10 system. When exiting "ZONES / DEVICES" menu the PowerMaster-10 system
displays the number of devices that need to be updated, as follows: DEV UPDATING NNN.
You can now press the button to delete the device of the same type, or press the button to delete a different device, or press the
button to take you to "
4.5.5 Modifying a Device
D. To Modify a Device
Note: This procedure is applicable to detectors only.
1.
2.
3.
4.
5.
ADD NEW DEVICES
or
MODIFY DEVICES
CONTACT SENSORS
or
Z01:Motions Sens
Repeat steps 1 to 3 in section 4.5.2 "Adding a Wireless Device".
Select the desired sensor to be modified. Select between "CONTACT
SENSORS", "MOTION SENSORS", "SMOKE SENSORS" and "WIRED SENSORS", for example, "MOTION SENSORS".
<OK> TO EXIT
".
6.
7.
8.
9.
10
22 D-302756
Z01:LOCATION
Front door
or
Master Bdrm
Z01:ZONE TYPE
12.Non-Alarm
or
3. Home Delay
The PowerMaster-10 display will read "Front door".
Select a location, or, enter the location number, for example, "Master Bdrm".
Select a zone type, or, enter the zone type number, for example, pressing 03 selects "3. Home Delay".
To understand the behavior of each zone, see section 4.5.2.3 Zone Types.
11.
12.
13.
14.
Z01: SET CHIME
Chime off….
or
melody-chime
Press skip.
Select between "CHIME OFF" and "melody-chime".
Note: In "melody chime" mode when a chime zone is triggered, chime melody is heard
You can now press the button to modify the next device of the same type, or press the button to configure the parameters of the device (see the Accessories Guide for instructions), or press the button to take you to "
to change chime settings or press the button to
<OK> TO EXIT
".
4.5.6 Replacing a Device
This feature is used for replacing a device that is enrolled in the system with another device of the same type while keeping the same parameters of the original device. This can save valuable time, since instead of having to delete the original device from the control panel, then to enroll the new device and then to set the device parameters again – all this can now be performed in one short procedure.
To Replace a Device
1.
2.
3.
4.
5.
6.
7
8.
ZONES/DEVICES
ADD NEW DEVICES
or
REPLACE DEVICES
CONTACT SENSORS
or
CONTACT SENSORS
Z01: Contact Sens
ID No. 100-2340
or
Repeat steps 1 to 4 of section 4.2 "Entering the Installer Menu".
Select the desired device type to be replaced. Select between "CONTACT SENSORS", "MOTION SENSORS", "SMOKE SENSORS", "KEYFOBS", "SIRENS" or "REPEATERS", for example, "CONTACT SENSORS".
The PowerMaster-10 display will read the name of the first enrolled device of the selected type to be replaced alternating with the ID number of the device.
At this stage you can select another device of the same type (in this example, contact sensor) to be replaced.
D-302756 23
9.
ENROLL NOW or
ENTR ID:100-xxxx
DEVICE ENROLLED
Z01: Contact Sens
ID No. 100-2332
Enroll the new device, or, enter the last 4 digits of the ID number of the new device.*
The PowerMaster-10 display will read the result.**
* If the device was previously enrolled in the system, the PowerMaster-
10 display reads " name of the device alternating with the ID number of the device.
If the device ID number is invalid the PowerMaster-10 display reads "
WRONG ID No
If the new device type is different from the existing device to be replaced, the PowerMaster-10 display reads "
** If the device was enrolled manually, by entering the ID number, the
PowerMaster-10 display reads "
At the end of the procedure you can press the button and perform the same procedure for a different device of the same type, or you can press the button to select a different device type to be replaced, or you can press the button to take you to “
ALREADY ENROLLED
".
" and then switches to the
WRONG DEV.TYPE
ID ACCEPTED
".
<OK> TO EXIT
".
”.
4.5.7 Defining Defaults
Attention! When changing the default parameters of one device in Define Defaults, all new devices of the same device type that are enrolled in the PowerMaster-10 system will have the same defaults. Devices that were already enrolled in the PowerMaster-10 system before the procedure was performed will not be affected by the new default settings.
To Define Device Defaults
1.
2.
3.
4.
5.
6.
ZONES/DEVICES
ADD NEW DEVICES
or
DEFINE DEFAULTS
CONTACT SENSORS
or
KEYFOBS
Repeat steps 1 to 4 of section 4.2 "Entering the Installer Menu".
Select the desired device whose defaults you wish to define. Select between "CONTACT SENSORS", "MOTION SENSORS", "SMOKE SENSORS", "KEYFOBS" and "SIRENS", for example, "KEYFOBS".
24 D-302756
For reviewing parameter configurations refer to the PowerMaster-10 Accessories Guide in section "MODIFY DEVICE SETTINGS" of the desired device.
At the end of the procedure you can press the button and perform the same procedure for a different device or you can press the
button to take you to “
<OK> TO EXIT
”.
4.6 Siren Configuration
4.6.1 Configuring the Length of Time the Bell is allowed to Function
Here you select the length of time the bell (or siren) is allowed to function upon alarm. The bell time starts upon activation of the siren. Once the bell time expires, the siren is automatically shut down.
Available options are: 1, 3, 4 (default), 8, 10, 15 and 20 minutes.
Note: To comply with EN requirements, the Bell Time should be set to 15 min. max.
To Configure the Length of Time the Bell is Allowed to Function
1.
2.
3.
4.
5.
6.
DEFINE PANEL
01:ENTRY DELAY 1
or
4:BELL TIME
bell time 4m 
or
4:BELL TIME
Repeat steps 1 to 4 of section 4.2 "Entering the Installer Menu".
Select between "bell time 1m", "bell time 3m", "bell time 4m", "bell time 8m", "bell time 10m", "bell time 15m" and "bell time 20m".
You can now press the or button to program any other menu in "
TO EXIT
DEFINE PANEL
".
" or press the button to take you to "
<OK>
4.6.2 Enabling the Internal Siren
Here you determine whether the internal siren will sound or remain silent upon alarm (according to the user preference). Options: piezo siren on (default), piezo siren off.
To Enable the Internal Siren
1.
2.
3.
D-302756 25
01:ENTRY DELAY 1
24:PIEZO SIREN
DEFINE PANEL
or
Repeat steps 1 to 4 of section 4.2 "Entering the Installer Menu".
4.
5.
6.
piezo siren ON 
or
24:PIEZO SIREN
Select between "piezo siren ON" and "piezo siren OFF".
You can now press the or button to program any other menu in "
TO EXIT
DEFINE PANEL
".
" or press the button to take you to "
4.6.3 Configuring the Period of Strobe Light Activation
Here you can define the period of strobe light activation when the siren is in alarm state. Options: 5 minutes, 10 minutes, 20 minutes (default), 40 minutes and 60 minutes.
To Configure the Period of Strobe Light Activation
1.
2.
3.
4.
5.
6.
DEFINE PANEL
01:ENTRY DELAY 1
or
40:STROBE TIME
20 minutes 
or
40:STROBE TIME
Repeat steps 1 to 4 of section 4.2 "Entering the Installer Menu".
Select between "5 minutes", "10 minutes", "20 minutes", "40 minutes" and "60 minutes".
You can now press the or button to program any other menu in "
TO EXIT
DEFINE PANEL
".
" or press the button to take you to "
<OK>
<OK>
4.6.4 Enabling Siren Activation upon Telephone Line Failure
Here you determine whether the siren will be activated or not when the telephone line fails during system armed state. Available options are: enable on fail, disable on fail (default).
To Enable Siren Activation upon Telephone Line Failure
1.
2.
3.
26 D-302756
01:ENTRY DELAY 1
27:SIREN ON LINE
DEFINE PANEL
or
Repeat steps 1 to 4 of section 4.2 "Entering the Installer Menu".
4.
5.
6.
disable on fail
or
27:SIREN ON LINE
Select between "disable on fail" and "enable on fail".
You can now press the or button to program any other menu in "
TO EXIT
DEFINE PANEL
".
" or press the button to take you to "
<OK>
4.7 Event Reporting Configuration
4.7.1 General
The PowerMaster-10 system uses an IP platform that supports GSM and GPRS cellular communication and broadband to forward all events received at the control panel to the monitoring station.
4.7.2 Setup Report Communicators
4.7.2.1 Configuring PSTN / GSM Communicators
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
DEFINE COMM.
1:PSTN/GSM
AREA CODE
TEL. AREA CODE
AREA CODE
LINE PREFIX
LINE PREFIX
LINE PREFIX
DIAL METHOD
Pulse 
or
Repeat steps 1 to 4 of section 4.2 "Entering the Installer Menu".
Enter the system tel. area code (up to 4 digits).
Enter the number that is used as a prefix to access an outside telephone line (if exists).
Here you determine the dialing method used by the automatic dialer built into the PowerMaster-10 control panel.
Select between "Pulse" and "tone (dtmf)".
D-302756 27
13.
14.
15.
16.
DIAL METHOD
GSM KEEP ALIVE
disable 
or
GSM KEEP ALIVE
Here you prevent the GSM Service provider from disconnecting the GSM line if the user has not initiated any outgoing telephone calls during the last 28 days.
Select between "disable" and "every 28 days".
You can now press the button to revert to the " or press the button to take you to "
<OK> TO EXIT
AREA CODE
".
" menu,
4.7.2.2 Configuring GPRS / BB Communicators
The GSM/GPRS module is capable of communicating with the Monitoring station receiver by GPRS, GSM Voice and SMS Channels. Each of the channels can be separately enabled or disabled in order to allow or prohibit the module from using it for the event reporting. If all channels are enabled, the GSM/GPRS module will always try GPRS first. If fails, it will try GSM voice. If fails, it will try any other possible method (PSTN Broadband) and only then it will try SMS. This is due to the fact that SMS the most unreliable option of communication. Disabling any of the GSM Module channels will cause the module to use a different sequence than the one described above.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
28 D-302756
DEFINE COMM.
1:PSTN/GSM
2:GSM/GPRS
GPRS REPORT
disable 
or
GPRS REPORT
GSM REPORT
disable 
or
GSM REPORT
Repeat steps 1 to 4 of section 4.2 "Entering the Installer Menu".
Here you determine whether the alarm system will report events to the Monitoring Station via the GPRS Channel.
Select between "disable" and "enable".
Here you determine whether the alarm system will report events to the Monitoring Station via the GSM Voice channel.
Select between "disable" and "enable".
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
28.
29.
30.
31.
SMS REPORT
disable 
or
SMS REPORT
GPRS APN
APN NAME
GPRS APN
GPRS USERNAME
APN USERNAME
GPRS USERNAME
GPRS PASSWORD
APN PASSWORD
GPRS PASSWORD
PIN CODE
PIN CODE
PIN CODE
Here you determine whether the alarm system will report events to the Monitoring Station via the SMS Channel.
Select between "disable" and "enable".
Enter the name of the APN Access Point used for the internet settings for the GPRS (up to 40 digits).
Note: The table at the end of this section provides a list of the keys used by the PowerMaster-10 editor.
Enter the username of the APN used for GPRS communications (up to 30 digits).
Note: The table at the end of this section provides a list of the keys used by the PowerMaster-10 editor.
Enter the password of the APN used for GPRS communications (up to 16 digits).
Note: The table at the end of this section provides a list of the keys used by the PowerMaster-10 editor.
Enter the PIN code of the SIM card installed in the PowerMaster-10 unit (up to 16 digits).
D-302756 29
o
32.
33.
34.
35.
36.
37.
38.
39.
Key Functionality
FORCE HOME NTWK.
disable 
FORCE HOME NTWK.
SESSION TIMEOUT
ff on timeout
SESSION TIMEOUT
Moves the cursor from left to right. Long press for speed.
Moves the cursor from right to left. Long press for speed.
Scrolls upward the sequence of inserted digits. Long press for speed.
Scrolls downward the sequence of inserted digits. Long press for speed.
Places cursor to extreme right position of edit string and shows the last 16 digits of edit string.
Reverts to previous or top menu without saving the edit string. Reverts to "<OK> TO EXIT" without saving the edit string.
Saves and reverts to previous menu.
Clears all digits to the right of cursor.
Clears one digit by cursor.
Selects between uppercase or lowercase digits.
or
or
Here you determine whether the alarm system will report events to the Monitoring Station via the GSM Voice channel.
Select between "disable" and "enable".
Here you determine whether the control panel will stay continuously connected via GPRS communication, or, temporarily connected to receive event reports only.
Select between "off on timeout" and "always ON".
You can now press the button to take you to the " menu, or press the button to take you to "
<OK> TO EXIT
GPRS REPORT
".
"
4.7.3 Configuring Event Reporting to Monitoring Station.
Here you determine which types of event will be reported to Monitoring Stations. Due to lack of space in the display, abbreviations are used: alarm is “alrm”, alert is “alrt” and open/close is “o/c”. The asterisk (J) is a separator between events reported to Monitoring Station 1 and events reported to Monitoring Station 2. Messages are divided by type into the following groups:
30 D-302756
Group Abbr. Events Reported
Alarms alrm Fire, Burglary, Panic, Tamper Open/close o/c Arming AWAY, Arming HOME, Disarming Alerts Alrt No-activity, Emergency, Latchkey Maintenance - Low-battery AC failure "Alarm" group has the highest priority and "Alert" group has the lowest priority.
The selectable options are as follows:
Plan name Sent to center 1 Sent to center 2
"all -o/c J backup" All but open/close "all J all" All All "all-o/c J all -o/c " All but open/close All but open/close "all –o/c J o/c " All but open/close Open/close "all (–alrt) J alrt" All but alerts Alerts "alrm J all (–alrm)" Alarms All but alarms "disable report" Nothing Nothing "all J backup" All All if cent. 1 doesn’t respond
Note:All” means that all 4 groups are reported and also trouble messages - sensor / system low battery, sensor inactivity, power failure, jamming, communication failure etc.
All but open/close if center 1 doesn’t respond
4.7.3.1 Configuring the Types of Events to be Reported
1.
2.
3.
4.
5.
6.
7.
3:C.S. REPORTING
REPORT EVENTS
all-o/c*backup
REPORT EVENTS
DEFINE COMM.
1:PSTN/GSM
or
or
Repeat steps 1 to 4 of section 4.2 "Entering the Installer Menu".
Select between "all-o/c* backup", "all *all", "all- o/c*all-o/c", "all-o/c*o/c", "all(-alrt)*alrt", "alrm*all(-alrm)", "disable report" and "all *backup".
You can now press the button to take you to the "
METHOD EXIT
" menu, or press the button to take you to "
".
1st RPRT
<OK> TO
4.7.3.2 Configuring the Communicators Report Sequence
Continue below from the previous section or repeat steps 1 to 4 of section 4.7.3.1 before continuing with the following instructions:
1.
D-302756 31
REPORT EVENTS
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
1st RPRT METHOD
disable 
or
1st RPRT METHOD
2nd RPRT METHOD
disable 
or
2nd RPRT METHOD
3rd RPRT METHOD
disable 
or
3rd RPRT METHOD
DUAL REPORTING
disable 
or
DUAL REPORTING
Here you define the 1st priority of method used to report events.
Select between "disable", "cellular", "broadband" and "PSTN".
nd
Here you define the 2 method defined to report events in the 1st priority fails, the control panel will attempt to report using the method defined in the 2nd priority.
Select between "disable", "cellular", "broadband" and "PSTN".
Here you define the 3 method defined to report events in the 2 will attempt to report using the method defined in the 3rd priority.
Select between "disable", "cellular", "broadband" and "PSTN".
Here you determine whether to report events using PSTN and cellular at the same time instead of waiting for the 1
nd
the 2
method.
Select between "disable", "PSTN & broadband", and "PSTN & cellular".
You can now press the button to take you to the "
ACCOUNT# EXIT
" menu, or press the button to take you to "
".
priority method used to report events. If the
rd
priority method used to report events. If the
nd
priority fails, the control panel
st
method to fail before trying
RCVR 1
<OK> TO
4.7.3.3 Configuring Account Numbers to be Reported to the Monitoring Station
Continue below from the previous section or repeat steps 1 to 4 of section 4.7.3.1 before continuing with the following instructions:
32 D-302756
1.
2.
3.
4.
5.
6.
7.
8.
REPORT EVENTS
or
RCVR 1 ACCOUNT#
1st acc. #001234
1st RCVR ACC. NO.
RCV 1 ACCOUNT#
RCV 2 ACCOUNT#
2nd acc. #001234
2nd RCVR ACC. NO.
RCV 2 ACCOUNT#
Here you enter the number that will identify your specific alarm control system to the 1 hexadecimal digits.
Enter the first receiver account number.
Here you enter the number that will identify your system to the 2 Monitoring Station. The account number consists of 6 hexadecimal digits.
Enter the second receiver account number.
You can now press the button to take you to the "
RCVR 1
" menu, or press the button to take you to "
EXIT
".
st
Monitoring Station. The number consists of 6
nd
PSTN/GSM
<OK> TO
4.7.3.4 Configuring the Monitoring Station's Telephone Numbers and IP Addresses
This mode allows you to adapt the telephone communication parameters to the local requirements. Continue below from the previous section or repeat steps 1 to 4 of section 4.7.3.1 before continuing with the
following instructions:
st
Here you program the telephone number of the 1 (including area code, 16 digit max.) to which the system will report the event groups defined in Report Events.
Enter the telephone number of the first PSTN/GSM receiver (for further details see the table at the end of this section).
Here you program the telephone number of the 2 (including area code, 16 digit max.) to which the system will report the event groups defined in Report Events.
Enter the telephone number of the second PSTN/GSM receiver (for further details see the table at the end of this section).
Monitoring Station
nd
Monitoring Station
1.
2.
3.
4.
5.
6.
REPORT EVENTS
or
PSTN/GSM RCVR 1
PSTN/GSM RCVR 1
PSTN/GSM RCVR 2
D-302756 33
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
Compatible Monitoring Station receivers are: Osborne-Hoffman model 2000, Ademco Model 685, FBII Model CP220, Radionics Model D6500, Sur­Gard Model SG-MLR2-DG and Silent Knight Model 9500.
IMPORTANT: In telephone number locations and account number locations, you may be required to enter hexadecimal digits. In telephone number locations, these digits are used as codes to control the dialer:
PSTN/GSM RCVR 2
IP RCVR 1
000.000.000.000
IP RCVR 1
IP RCVR 2
000.000.000.000
IP RCVR 2
SMS RCVR1
SMS RCVR1
SMS RCVR2
SMS RCVR2
Here you enter the IP address of the IP receiver that is located in the 1 Monitoring Station.
Enter the IP address of the first IP receiver (for further details see the table at the end of this section).
Here you enter the IP address of the IP receiver that is located in the 2 Monitoring Station.
Enter the IP address of the second IP receiver (for further details see the table at the end of this section).
Here you enter the telephone number of the SMS receiver that is located
st
in the 1
Enter the telephone number of the first SMS receiver (for further details see the table at the end of this section).
Here you enter the telephone number of the SMS receiver that is located in the 2
Enter the telephone number of the second SMS receiver (for further details see the table at the end of this section).
You can now press the button to take you to the "
FORMAT EXIT
Monitoring Station.
nd
Monitoring Station.
" menu, or press the button to take you to "
".
st
nd
PSTN RPRT
<OK> TO
34 D-302756
Hex.Digit Keying
Sequence
A <#> ⇒ <0> Applicable only at the beginning of a number - the dialer waits 10
D <#> ⇒ <3> Applicable only at the beginning of a number - the dialer waits 5 seconds
E <#> ⇒ <4> Applicable only in the middle of the number - the dialer waits 5 seconds F <#> ⇒ <5> Not applicable in phone numbers
Note: A "+" can be entered at the beginning of the line by pressing
To enter a series of digits, use the following keys: <Numeric keypad> - to enter the number
- moves the cursor from left to right
- moves the cursor from right to left
- deletes everything after the cursor (to the right)
Code Significance
seconds or waits for dial tone, whichever comes first and then dials.
for dial tone and goes on hook if none is received.
and then .
4.7.3.5 Configuring the Report Method (Protocol) to Monitoring Station
Continue below from the previous section or repeat steps 1 to 4 of section 4.7.3.1 before continuing with the following instructions:
Here you select the reporting format used by the control panel to report events to Monitoring Stations.
Select between "SIA", "4/2 1900/1400", "4/2 1800/2300", "Scancom", "SIA text" and "contact ID".
Here you select the pulse rate at which data will be sent to Monitoring Stations if any one of the 4/2 formats has been selected in PSTN Report Format.
Select between "10 pps", "20 pps", "33 pps" and "40 pps".
You can now press the button to take you to the "
RETRY
" menu, or press the button to take you to "
EXIT
".
PSTN RPRT
<OK> TO
1.
2.
3.
4.
5.
6.
7.
8.
REPORT EVENTS
or
PSTN RPRT FORMAT
SIA 
or
PSTN RPRT FORMAT
4/2 PULSE RATE
20 pps 
or
4/2 PULSE RATE
4.7.3.6 Configuring the Number of Retry Attempts
Continue below from the previous section or repeat steps 1 to 4 of section 4.7.3.1 before continuing with the following instructions:
1.
D-302756 35
REPORT EVENTS
or
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
PSTN RPRT RETRY
4 attempts 
or
PSTN RPRT RETRY
GSM RPRT RETRY
4 attempts 
or
GSM RPRT RETRY
LAN RPRT RETRY
4 attempts 
or
LAN RPRT RETRY
Here you determine the number of times the communicator will dial the Monitoring Station’s number via PSTN.
Select between "2 attempts", "4 attempts", "8 attempts", "12 attempts" and "16 attempts".
Here you determine the number of times the communicator will try to report via a cellular group (GPRS, GSM and SMS) to the Monitoring Station.
Select between "2 attempts", "4 attempts", "8 attempts", "12 attempts" and "16 attempts".
Here you determine the number of times the communicator will try to report via the PowerLink Broadband Module communication to the Monitoring Station.
Select between "2 attempts", "4 attempts", "8 attempts", "12 attempts" and "16 attempts".
You can now press the button to take you to the "
TIME
" menu, or press the button to take you to "
<OK> TO EXIT
AUTO TEST
".
4.7.3.7 Configuring the Auto Test Report
Continue below from the previous section or repeat steps 1 to 4 of section 4.7.3.1 before continuing with the following instructions:
1.
2.
3.
4.
36 D-302756
REPORT EVENTS
or
AUTO TEST TIME
test time 12:00P
AUTO TEST TIME
Here you determine the time at which the telephone line will be tested and reported to the Monitoring Station.
Enter the auto test time.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
AUTO TEST CYCLE
test OFF 
or
AUTO TEST CYCLE
LINE FAIL REPORT
PSTN
immediately 
or
PSTN
GSM/GPRS
don’t report 
or
GSM/GPRS
broadband
don’t report 
or
Here you determine the time interval between consecutive telephone line test messages sent to the Monitoring Station. The control panel performs this at regular intervals to verify proper communications.
Select between "test OFF", "test every 1 d", "test every 2 d", "test every 5 d", "test every 7 d", "test every 14 d", "test every 30 d" and "test every 5 h".
Here you determine if the PSTN telephone line disconnection will be reported or not and determine the delay between detection of line disconnection and the failure reporting. If the telephone line is disconnected, the event "tel line fail" will be stored in the event log.
Select between "immediately", "5 minutes", "30 minutes", "60 minutes", "180 minutes" and "don't report".
Here you determine if the GSM/GPRS line disconnection will be reported or not and determine the delay between detection of line disconnection and report failure. If the telephone line is disconnected, the event "GSM line fail" will be stored in the event log.
Select between "2 minutes", "5 minutes", "30 minutes", "60 minutes", "180 minutes" and "don't report".
Here you determine if the PowerLink Broadband Module line disconnection will be reported or not and determine the delay between detection of line disconnection and report failure. If the telephone line is disconnected, the event "PLNK line fail" will be stored in the event log.
Select between "2 minutes", "5 minutes", "30 minutes", "60 minutes", "180 minutes" and "don't report".
D-302756 37
21.
broadband
LINE FAIL REPORT
You can now press the button to take you to the " menu (see Configuring Remote Programming Access Permissions), or press the button to take you to "
<OK> TO EXIT
PSTN UP/DOWN
".
4.7.3.8 Configuring the Event Types to be Reported to the Monitoring Station
Continue below from the previous section or repeat steps 1 to 4 of section 4.7.3.1 before continuing with the following instructions:
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
REPORT EVENTS
or
RPRT CNFRM ALARM
disable report
or
RPRT CNFRM ALARM
RECENT CLOSE
recent cl. OFF
or
RECENT CLOSE
ZONE RESTORE
report restore
or
ZONE RESTORE
SYS INACT REPORT
Here you determine whether the system will report whenever 2 or more events (confirmed alarm) occur during a specific period.
Select between "disable report", "enable + bypass" and "enable report".
Here you enable or disable the “recent closing” report, that is sent to the Monitoring Station if an alarm occurs within 2 minutes from the expiry of the exit delay.
Select between "recent cl. OFF" and "recent cl. ON".
Here you determine whether a zone restore will be reported or not.
Select between "report restore" and "don't report".
Here you determine whether the Monitoring Station will receive a message if the system is inactive (not armed) during a defined period (days).
"
38 D-302756
15.
16.
disable 
or
SYS INACT REPORT
Select between "disable", "rep. after 7d", " rep. after 14d ", " rep. after 30d", and "rep. after 90d".
You can now press the button to take you to the "
EVENTS
you to "
" menu (see section 4.7.2.1), or press the button to take
<OK> TO EXIT
4.7.4 Configuring Event Reporting to Users
A. To Enable Report to Users
1.
2.
3.
4.
5.
4:PRIVATE REPORT
REPORT TO PRVT
disable report
DEFINE COMM.
1:PSTN/GSM
or
Repeat steps 1 to 4 of section 4.2 "Entering the Installer Menu".
REPORT
".
B. To Configure Event Types to be Reported to User
Here you determine which event groups will be reported to private telephone subscribers.
Term Description
"all" All messages "all (-op/cl)" All messages, except open/close "all (-alerts)" All messages, except alerts "alarms" Alarm messages "alerts" Alert messages "op/cl" Open/close "disable report" No message will be reported
Note:All” means all events including the L. BAT and AC FAIL trouble messages. Note: All the above options can be reported to private telephone subscribers by SMS. When Voice Report is
enabled alarms and alerts only can be reported. The following siren signal will be sent to private telephone upon event reporting:
FIRE: ON - ON - ON - pause.... (- - - - - - ......).
BURGLAR: ON continuously ( EMERGENCY/LATCHKEY: 2-tone siren; like an ambulance.
6.
7.
D-302756 39
REPORT TO PRVT
or
Select between "disable report", "all", "all (-op/cl)", "all(- alerts)", "alarms", "alerts" and "op/cl".
...)
C. To Configure Event Types to be Reported to User
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
1st private tel#
1st PRIVATE TEL. NO.
1st private tel#
2nd private tel#
2nd PRIVATE TEL. NO.
2nd private tel#
3rd private tel#
3rd PRIVATE TEL. NO.
3rd private tel#
4th private tel#
4th PRIVATE TEL. NO.
4th private tel#
Redial attempts
VOICE REPORT
You can now press the button to take you to the "
REPORT EXIT
Enter the first private telephone number (including area code, if required) of the private subscriber to which the system will report the event groups defined in Report To Private.
Enter the second private telephone number (including area code, if required) of the private subscriber to which the system will report the event groups defined in Report To Private.
Enter the third private telephone number (including area code, if required) of the private subscriber to which the system will report the event groups defined in Report To Private.
Enter the fourth private telephone number (including area code, if required) of the private subscriber to which the system will report the event groups defined in Report To Private.
Here you determine the number of times the communicator will dial the called party’s number (private telephone).
" menu, or press the button to take you to "
".
VOICE
<OK> TO
40 D-302756
27.
28.
29.
30.
31.
32.
33.
3 attempts 
or
Redial attempts
Tel. acknowledge
single ack 
or
Tel. acknowledge
VOICE REPORT
Select between "1 attempt", "2 attempts", "3 attempts" and "4 attempts".
Attention! A maximum of 2 dialing attempts is permitted by the Australian Telecommunication Authority.
Here you determine whether the system will use the single acknowledge or the all acknowledge
Note: In the single acknowledge from a single telephone is sufficient to consider the current event closed and call off the communication session. The remaining telephones serve for backup purposes only. In the all acknowledge signal must be received from each telephone before the current event is considered reported.
Select between "single ack" and "all ack".
You can now press the button to take you to the "
TEL#
" menu (see the next section), or press the button to take
you to "
<OK> TO EXIT
mode when reporting to private telephones.
mode, receiving an acknowledge signal
mode, an acknowledge
SMS REPORT
".
D. To Configure Reports to User by SMS
34.
35.
36.
37.
38.
39.
40.
41.
D-302756 41
VOICE REPORT
SMS REPORT TEL#
1st SMS tel#
1st SMS TEL. NO.
1st SMS tel#
2nd SMS tel#
2nd SMS TEL. NO.
Enter the first SMS phone number (including area code, 16 digits max.) to which pre-selected event types will be reported.
Enter the second SMS phone number (including area code, 16 digits max.) to which pre-selected event types will be reported.
42.
43.
44.
45.
46.
47.
48.
49.
2nd SMS tel#
3rd SMS tel#
3rd SMS TEL. NO.
3rd SMS tel#
4th SMS tel#
4th SMS TEL. NO.
4th SMS tel#
Enter the third SMS phone number (including area code, 16 digits max.) to which pre-selected event types will be reported.
Enter the fourht SMS phone number (including area code, 16 digits max.) to which pre-selected event types will be reported.
You can now press the button to take you to the "
tel#
" menu (see step C. To Configure Event Types to be Reported to
User), or press the button to take you to "
<OK> TO EXIT
1st private
".
4.8 Security System Configuration
4.8.1 Enable Cross Zoning
Here you determine whether cross zoning will be active or inactive. Cross zoning is a method used to counteract false alarms - an alarm will not be initiated unless two adjacent zones are violated within a 30-second time limit.
This feature is active only when arming AWAY and only with zone couples from zone No. 18 to 27 20 and 21, etc.). You may use any one of these zone couples to create a “cross-zoned” area.
Note: If one of two crossed zones is bypassed (see Para. 4.3.5), the remaining zone will function independently. Note: Every 2 crossed zones must be of the allowed zone type (Interior, Perimeter, Perimeter follower).
The options are: cross zone ON and cross zone OFF (default).
Cross zoning is not applicable in Entry/ Exit zones and 24h zones (Fire, Emergency, 24h audible, 24h silent).
To Enable Cross Zoning
1.
2.
3.
4.
5.
6.
42 D-302756
01:ENTRY DELAY 1
14:CROSS ZONING
cross zone OFF 
DEFINE PANEL
or
or
Repeat steps 1 to 4 of section 4.2 "Entering the Installer Menu".
Select between "cross zone OFF" and "cross zone ON".
(18 and 19,
14:CROSS ZONING
You can now press the or button to program any other menu in "
TO EXIT
DEFINE PANEL
".
" or press the button to take you to "
<OK>
4.8.2 Configuring Swinger Stop
Here you determine the number of times each zone is allowed to initiate an alarm within a single arming/disarming period (including tamper & power failure events of detectors, PowerMaster-10, wireless siren, etc.). If the alarms number from a specific zone exceeds the programmed number, the control panel automatically bypasses the zone to prevent recurrent siren noise and nuisance reporting to the Monitoring Station. The zone will be reactivated upon disarming, or 48 hours after having been bypassed (if the system remains armed).
Available options are: shut after 1 (default), shut after 2 (default in USA), shut after 3 and no shutdown.
To Configure Swinger Stop
1.
2.
3.
4.
5.
6.
DEFINE PANEL
01:ENTRY DELAY 1
or
13:SWINGER STOP
shut after 1 
or
13:SWINGER STOP
Repeat steps 1 to 4 of section 4.2 "Entering the Installer Menu".
Select between "shut after 1", "shut after 2", "shut after 3" and "no shutdown".
You can now press the or button to program any other menu in "
TO EXIT
DEFINE PANEL
".
" or press the button to take you to "
<OK>
4.8.3 Enable Monitoring of Activity at Home
Here you determine the time limit for reception of signals from sensors used to monitor the activity of sick, elderly or disabled people. If no sensor detects and reports movement at least once within the defined time limit, a “not-active” alert is initiated.
Options: 3, 6, 12, 24, 48, 72 hours and no act disable (default).
To Configure Monitoring of Activity at Home
1.
2.
3.
D-302756 43
01:ENTRY DELAY 1
DEFINE PANEL
or
Repeat steps 1 to 4 of section 4.2 "Entering the Installer Menu".
4.
5.
6.
21:NOT ACTIVE
no act disable 
or
21:NOT ACTIVE
Select between "no act disable", "3 h", "6 h", "12 h", "24 h", "48 h", and "72 h".
You can now press the or button to program any other menu in "
TO EXIT
DEFINE PANEL
".
" or press the button to take you to "
<OK>
4.8.4 Configuring Alarm Cancel Period
Here you determine the ”cancel alarm” period that starts upon reporting an alarm to the Monitoring Station. If the user disarms the system within that time period, a “cancel alarm” message is sent to the Monitoring Station.
Available options are: cancel time 1 m, cancel time 5 m (default), cancel time 15 m, cancel time 60 m, cancel time 4 hours and also cancel inactive (default in USA).
Note: To comply with CP-01 requirements, "1 minute" option is not available
To Configure the Alarm Cancel Period
1.
2.
3.
4.
5.
6.
DEFINE PANEL
01:ENTRY DELAY 1
or
06:ALARM CANCEL
cancel time 5 m
or
06:ALARM CANCEL
Repeat steps 1 to 4 of section 4.2 "Entering the Installer Menu".
Select between "cancel time 1 m", "cancel time 5 m", "cancel time
15 m", "cancel time 60 m", "cancel time 4 h", and "cancel inactive".
You can now press the or button to program any other menu in "
TO EXIT
DEFINE PANEL
".
" or press the button to take you to "
.
<OK>
4.8.5 Configuring Power Failure Threshold Period
Here you determine the time interval between AC power failure occurrence and the failure reporting. Options: 5 minutes (default), 30 minutes, 60 minutes or 180 minutes.
Note: To comply with EN requirements, set to 60 min. max.
44 D-302756
To Configure the Power Failure Threshold Period
1.
2.
3.
4.
5.
6.
DEFINE PANEL
01:ENTRY DELAY 1
or
34:AC FAIL REP
5 minutes 
or
34:AC FAIL REP
Repeat steps 1 to 4 of section 4.2 "Entering the Installer Menu".
Select between "5 minutes", "30 minutes", "60 minutes", and "180 minutes".
You can now press the or button to program any other menu in "
TO EXIT
DEFINE PANEL
".
" or press the button to take you to "
<OK>
4.8.6 Configuring Abort Time
Here you select the length of time allowed by the system to abort an alarm (not applicable to alarms from FIRE, 24H SILENT and EMERGENCY zones). The PowerMaster-10 is programmed to provide an “abort interval” that starts upon detection of an event. During this interval, the buzzer sounds a warning but the siren remains inactive and the alarm is not reported. If the user disarms the system within the allowed abort interval, the alarm is aborted. Available options are: 00s (default in USA), 15s, 30s (default), 45s, 60s, 2m, 3m and 4m.
Note: To comply with CP-01 requirements, "60s", "3m" and "4m" options are not available Note: To comply with UL requirements, the abort time must not exceed 45 sec
.
.
To Configure the Abort Time
1.
2.
3.
4.
5.
6.
D-302756 45
01:ENTRY DELAY 1
05:ABORT TIME
abort time 30s 
05:ABORT TIME
DEFINE PANEL
or
or
Repeat steps 1 to 4 of section 4.2 "Entering the Installer Menu".
Select between "abort time 00s", "abort time 15s", "abort time 30s", "abort time 45s", "abort time 60s", "abort time 2m", "abort time 3m" and "abort time 4m".
You can now press the or button to program any other menu in "
TO EXIT
DEFINE PANEL
".
" or press the button to take you to "
<OK>
4.8.7 Configuring a Confirmed Alarm
Here you determine that if 2 successive alarms will occur during a specific period, the second alarm will be considered as a confirmed alarm for confirmed alarm reporting, (see par. 4.6.3.2 "Configuring the Event Types to be Reported"). Options: disable (default in USA), 30 min., 45 min., 60 min. (default), or 90 min.
To Configure a Confirmed Alarm
1.
2.
3.
4.
5.
6.
DEFINE PANEL
01:ENTRY DELAY 1
or
33:CONFIRM TIME
60 minutes 
or
33:CONFIRM TIME
Repeat steps 1 to 4 of section 4.2 "Entering the Installer Menu".
Select between "disable", "30 minutes", "45 minutes", "60 minutes", and "90 minutes".
You can now press the or button to program any other menu in "
TO EXIT
DEFINE PANEL
".
" or press the button to take you to "
<OK>
4.8.8 Enable Alarm upon Detection of Jammed or Missing Device
Here you determine whether an alarm will be initiated (siren / report) when there is a supervision / jamming failure during AWAY arming state. Available options are: EN standard and other (default). When "EN standard" is selected, if there is supervision / jamming failure during AWAY arming, the siren is activated and the events are reported as tamper events. When "Other" is selected, there is no such activity during AWAY arming.
To Enable an Alarm Upon Detection of a Jammed or Missing Device
1.
2.
3.
4.
5.
6.
46 D-302756
01:ENTRY DELAY 1
30:BELL/REP.OPT
30:BELL/REP.OPT
DEFINE PANEL
or
other 
or
Repeat steps 1 to 4 of section 4.2 "Entering the Installer Menu".
Select between "EN standard", and "other".
You can now press the or button to program any other menu in "
TO EXIT
DEFINE PANEL
".
" or press the button to take you to "
<OK>
4.8.9 Configuring the Jamming Detection
Here you determine whether jamming (interfering transmissions, on the radio channel used by the system) will be detected and reported or not. If a jam detection option is selected, the system does not allow arming under the relevant jamming conditions.
Jam Detection Options
Option Detection and Reporting when
UL 20/20
(USA standard)
EN 30/60
(Europe standard)
class 6 (30/60) (British standard)
Disable (default) (No jamming detection and reporting).
To Configure the Jamming Detection
1.
2.
3.
4.
5.
6.
01:ENTRY DELAY 1
19:JAM DETECT
19:JAM DETECT
DEFINE PANEL
or
disable 
or
There is continuous 20 seconds of jamming
There is an accumulated 30 seconds of jamming within 60 sec.
Like EN (30/60) but the event will be reported only if the jamming duration exceeds 5 minutes.
Repeat steps 1 to 4 of section 4.2 "Entering the Installer Menu".
Select between "UL 20/20", "EN 30/60", "class 6 (30/60)" and "disable".
You can now press the or button to program any other menu in "
TO EXIT
DEFINE PANEL
".
" or press the button to take you to "
<OK>
4.8.10 Configuring Whether a Missing Device Causes the System to Become
"NOT READY"
Here you determine if the system will be in NOT READY status when there is a supervision failure. In the "in supervision" mode, the system will be in NOT READY status if during the last 20 minutes a supervision message was not received. Options: normal (default) and in supervision.
Note: To comply with EN requirements, "in supervision" must be selected.
D-302756 47
To Configure whether a missing device causes the system to become "NOT READY"
1.
2.
3.
4.
5.
6.
DEFINE PANEL
01:ENTRY DELAY 1
or
16:NOT READY
normal 
or
16:NOT READY
Repeat steps 1 to 4 of section 4.2 "Entering the Installer Menu".
Select between "normal", and "in supervision".
You can now press the or button to program any other menu in "
TO EXIT
DEFINE PANEL
".
" or press the button to take you to "
<OK>
4.8.11 Configuring the Time Period by which a Device is considered Missing
Here you determine the time limit for reception of supervision reports from various supervised wireless devices. If any device does not report at least once within the selected time limit, an “INACTIVITY” alert is initiated.
The options are: 1, 2, 4, 8, 12 hours (default) and disable. Note: To comply with EN requirements, 1 or 2 hours must be selected.
To Configure the Time Period by which a Device is Considered Missing
1.
2.
3.
4.
5.
6.
DEFINE PANEL
01:ENTRY DELAY 1
or
15:SUPERVISION
superv time 12h
or
15:SUPERVISION
Repeat steps 1 to 4 of section 4.2 "Entering the Installer Menu".
Select between "superv time 1h", "superv time 2h", "superv time 4h", "superv time 8h", "superv time 12h" and "disable".
You can now press the or button to program any other menu in "
TO EXIT
DEFINE PANEL
".
" or press the button to take you to "
<OK>
48 D-302756
4.9 Arming/Disarming Options And Exit/Entry Delay
4.9.1 Configuring Exit Modes
Here you determine exit delay mode options. Three types of exit delay modes are available: restart exit - Exit delay restarts when the door is reopened during exit delay. The restart occurs once only. Restarting the exit delay is helpful if the user re-enters immediately after going out to retrieve an item that he left behind. off by door - When the door is closed, the exit delay is automatically terminated (even if the defined exit delay was not completed).
normal (default) - The exit delay is exactly as defined, regardless of whether the door is open or closed.
To Configure the Exit Modes
1.
2.
3.
4.
5.
6.
DEFINE PANEL
01:ENTRY DELAY 1
or
09:EXIT MODE
normal 
or
09:EXIT MODE
Repeat steps 1 to 4 of section 4.2 "Entering the Installer Menu".
Select between "restart exit", "off by door", and "normal".
You can now press the or button to program any other menu in "
TO EXIT
DEFINE PANEL
".
" or press the button to take you to "
<OK>
4.9.2 Configuring Entry Delays Duration
Two different entry delays allow the user to enter the protected site (while the system is in the armed state) via 2 specific doors and routes without causing an alarm.
Following entry, the user must disarm the control panel before the entry delay expires. Slow-rate warning beeps start sounding once the door is opened, until the last 10 seconds of the delay, during which the beeping rate increases. Locations No. 1 (entry delay 1) and 2 (entry delay 2) allow you to program the length of these delays. Available options for each delay are: "00s", "15s" (default for entry delay 2), "30s" (default for entry delay 1),
"45s", "60s", "3m" and "4m".
00s
" and "
15s
Note: To comply with CP-01 requirements, " Note: To comply with EN requirements, the entry delay must not exceed 45 sec Note: To comply with UL requirements, the entry delay must not exceed 15 sec
To Configure the Duration of the Entry Delays
1.
2.
D-302756 49
01:ENTRY DELAY 1
DEFINE PANEL
Repeat steps 1 to 4 of section 4.2 "Entering the Installer Menu".
*
" options are not available.
.
.
3.
4.
5.
entry dly1 30s 
or
09:EXIT MODE
Select between "entry dly1 00s", "entry dly1 15s", "entry dly1 30s", "entry dly1 45s", "entry dly1 60s", "entry dly1 3m" and "entry dly1 4m".**
* Press the button for "
** In the "
You can now press the or button to program any other menu in "
TO EXIT
02:ENTRY DELAY 2
"
entry dly2
DEFINE PANEL
".
…".
02:ENTRY DELAY 2
" menu, the PowerMaster-10 display will read
" or press the button to take you to "
".
<OK>
4.9.3 Configuring Exit Delay Duration
An exit delay allows the user to arm the system and leave the protected site via specific routes and doors without causing an alarm. Slow-rate warning beeps start sounding once the arming command has been given, until the last 10 seconds of the delay, during which the beeping rate increases. Location No. 3 allows
programming of the exit delay length. Available options are: 30s, 60s (default), 90s, 120s, 3m, and 4m
Note: To comply with CP-01 requirements, "30s" option is not available Note: To comply with UL requirements, the exit delay must not exceed 120 sec
.
.
.
To Configure the Exit Delay Duration
1.
2.
3.
4.
5.
6.
DEFINE PANEL
01:ENTRY DELAY 1
or
03:EXIT DELAY
exit delay 60s
or
03:EXIT DELAY
Repeat steps 1 to 4 of section 4.2 "Entering the Installer Menu".
Select between "exit delay 30s", "exit delay 60s", "exit delay 90s", "exit delay 120s", "exit delay 3m"and "exit delay 4m".
You can now press the or button to program any other menu in "
TO EXIT
DEFINE PANEL
".
" or press the button to take you to "
<OK>
4.9.4 Enabling Quick Arm
Here you determine whether the user will be allowed to perform quick arming or not. Once quick arming is permitted, the control panel does not request a user code before it arms the system.
The two options are: quick arm ON (default in USA) and quick arm OFF (default).
50 D-302756
To Enable Quick Arm
1.
2.
3.
4.
5.
6.
DEFINE PANEL
01:ENTRY DELAY 1
or
07:QUICK ARM
quick arm OFF 
or
07:QUICK ARM
Repeat steps 1 to 4 of section 4.2 "Entering the Installer Menu".
Select between "quick arm ON", and "quick arm OFF".
You can now press the or button to program any other menu in "
TO EXIT
DEFINE PANEL
".
" or press the button to take you to "
<OK>
4.9.5 Configuring Bypassing Zones
Here you permit either manual bypassing of individual zones (through the USER SETTINGS menu), or allow the system to "force arm" (perform automatic bypassing) of open zones during the exit delay. If desired, press the arming key again if you want to eliminate the protest tone that sounds during forced arming. If a zone is open and forced arming is not permitted, “NOT READY” is displayed and the system does not arm (the “Sad Melody” will sound). If "no bypass" is selected, neither manual bypassing nor force arming is allowed.
Options: manual bypass (default in USA), force arm and no bypass (default).
Note: To comply with EN requirements, "manual bypass" or "force arm" must be selected. Note: The option "force arm" is not applicable in the UK.
To Configure Bypass
1.
2.
3.
4.
5.
6.
D-302756 51
01:ENTRY DELAY 1
DEFINE PANEL
or
08:BYPASS
no bypass 
or
08:BYPASS
Repeat steps 1 to 4 of section 4.2 "Entering the Installer Menu".
Select between "manual bypass", "force arm" and "no bypass".
You can now press the or button to program any other menu in "
TO EXIT
DEFINE PANEL
".
" or press the button to take you to "
<OK>
4.9.6 Configuring Panic Alarm Activation
Here you determine whether the user will be allowed to initiate a panic alarm by simultaneous pressing of either the two panic buttons panic activates the siren and simultaneously transmits a message via telephone. Silent panic only transmits a message via telephone. The options are: silent panic, audible panic (default) and disable panic.
To Configure Panic Alarm Activation
1.
DEFINE PANEL
2.
3.
4.
5.
6.
01:ENTRY DELAY 1
12:PANIC ALARM
audible panic 
12:PANIC ALARM
(on the keypad / wireless commander) or away + home (on a keyfob transmitter). Audible
or
or
Repeat steps 1 to 4 of section 4.2 "Entering the Installer Menu".
Select between "silent panic", "audible panic" and "disable panic".
You can now press the or button to program any other menu in "
TO EXIT
DEFINE PANEL
".
" or press the button to take you to "
<OK>
4.9.7 Enabling Latchkey Arming
Here you determine whether the system can be armed in the latchkey mode. If the system is armed this way, a “latchkey” message will be sent to specific telephones upon disarming by a “latchkey user” (users 5-8 or keyfob transmitters 5-8). This mode is useful when parents at work want to be informed of a child’s return from school.
The options are: Latchkey ON and Latchkey OFF (default).
To Enable Latchkey Arming
1.
2.
3.
4.
5.
6.
52 D-302756
01:ENTRY DELAY 1
Latchkey OFF 
DEFINE PANEL
or
20:LATCHKEY
or
20:LATCHKEY
Repeat steps 1 to 4 of section 4.2 "Entering the Installer Menu".
Select between "Latchkey ON", and "Latchkey OFF".
You can now press the or button to program any other menu in "
TO EXIT
DEFINE PANEL
".
" or press the button to take you to "
<OK>
4.10 User Interface Customization
4.10.1 Enabling Trouble Beeps
Under trouble conditions, the sounder emits a series of 3 short beeps once per minute. Here you determine whether this special beeping sequence will be active, inactive, or just inactive at night (the range of “night” hours is defined in the factory but is usually from 8 PM until 7 AM). The 3 options are: enable beeps (default in USA), off at night (default) and disable beeps.
To Enable Trouble Beeps
1.
2.
3.
4.
5.
6.
DEFINE PANEL
01:ENTRY DELAY 1
or
11:TROUBLE BEEPS
off at night 
or
11:TROUBLE BEEPS
Repeat steps 1 to 4 of section 4.2 "Entering the Installer Menu".
Select between "enable beeps", "off at night" and "disable beeps".
You can now press the or button to program any other menu in "
TO EXIT
DEFINE PANEL
".
" or press the button to take you to "
<OK>
4.10.2 Enabling Piezo Beeps
Here you determine whether warning beeps will sound or muted during exit and entry delays. An additional option is to mute the warning beeps only when the system is armed “HOME”.
Options: enable beeps (default), off when home (default in USA) and disable beeps. Note: When exit beeps are disabled toward the end of a delay, the happy (success) melody will sound.
To Enable Piezo Beeps
1.
2.
3.
4.
D-302756 53
01:ENTRY DELAY 1
10:PIEZO BEEPS
DEFINE PANEL
or
Repeat steps 1 to 4 of section 4.2 "Entering the Installer Menu".
Select between "enable beeps", "off when home" and "disable beeps".
You can now press the or button to program any other menu in "
TO EXIT
DEFINE PANEL
".
" or press the button to take you to "
<OK>
5.
6.
enable beeps 
or
10:PIEZO BEEPS
4.10.3 Enabling the Back Light
Here you determine whether the keypad back lighting will remain on at all times or will turn on when a key is pressed and turn off within 10 seconds if no further keystrokes are sensed.
The two options are: always ON and OFF after 10 s (default).
To Enable the Back Light
1.
2.
3.
4.
5.
6.
DEFINE PANEL
01:ENTRY DELAY 1
or
22:BACK LIGHT
OFF after 10s 
or
22:BACK LIGHT
Repeat steps 1 to 4 of section 4.2 "Entering the Installer Menu".
Select between "OFF after 10s", and "always ON".
You can now press the or button to program any other menu in "
TO EXIT
DEFINE PANEL
".
" or press the button to take you to "
<OK>
4.10.4 Configuring the Disarm Option
Here you determine when it is possible to disarm the system:
A. Any time. B. In AWAY mode, during entry delay, by using the PowerMaster-10 keypad or wireless sensor (keyfob). C. In AWAY mode, during entry delay, by using a wireless device (keyfob) only (this is set as a default in UK to
comply with DD243). D. During entry delay, or by using the PowerMaster-10 keypad in AWAY mode. Options: any time (default), on entry wireless, entry + away kp (default in UK), or on entry all.
To Configure the Disarm Option
1.
54 D-302756
DEFINE PANEL
Repeat steps 1 to 4 of section 4.2 "Entering the Installer Menu".
2.
3.
4.
5.
6.
01:ENTRY DELAY 1
or
29:DISARM OPTION
any time 
or
29:DISARM OPTION
Select between "any time", "on entry wrless", "entry + away kp" and "on entry all".
You can now press the or button to program any other menu in "
TO EXIT
DEFINE PANEL
".
" or press the button to take you to "
<OK>
4.10.5 Configuring the Screen Saver Options
Here you can determine that if no key is pressed during more than 30 seconds the display will read “PowerMaster-10” (to prevent a possible intruder of knowing the system status). You can determine that normal
display will return after pressing the pressing any key (Refresh by Key).
If Refresh by Key is selected, the first pressing of any key (except Fire and Emergency) will cause normal display return and the second press will perform the key function. Regarding the Fire and Emergency keys, the first key press will cause normal display return and also will perform the Fire/Emergency function.
Options: scrn saver OFF (default), refresh by code, refresh by key.
Note: To comply with EN requirements, "refresh by code" must be selected.
To Configure the Screen Saver Option
1.
2.
3.
4.
5.
6.
01:ENTRY DELAY 1
32:SCREEN SAVER
scrn saver OFF
32:SCREEN SAVER
DEFINE PANEL
or
or
button followed by entering user code (Refresh by Code) or after
Repeat steps 1 to 4 of section 4.2 "Entering the Installer Menu".
Select between "scrn saver OFF", "refresh by Code", and "refresh by Key".
You can now press the or button to program any other menu in "
TO EXIT
DEFINE PANEL
".
" or press the button to take you to "
<OK>
D-302756 55
4.10.6 Enabling the Memory Prompt
Here you determine whether the user will receive indication that an alarm has been activated. Available options are: enable (default) and disable.
To Enable the Memory Prompt
1.
2.
3.
4.
5.
6.
DEFINE PANEL
01:ENTRY DELAY 1
or
28:MEMORY PROMPT
enable 
or
28:MEMORY PROMPT
Repeat steps 1 to 4 of section 4.2 "Entering the Installer Menu".
Select between "enable" and "disable".
You can now press the or button to program any other menu in "
TO EXIT
DEFINE PANEL
".
" or press the button to take you to "
<OK>
4.10.7 Enabling Keyfob Low Battery Acknowledgement
Here you determine whether the user will hear or will not hear low battery sound when he tries to disarm the system with a keyfob whose battery voltage is low. Available options are: keyfob L-B on - the user has to acknowledge the keyfob low battery message, or, keyfob
L-B off (default) - the user does not have to acknowledge the keyfob low battery message.
To Enable Keyfob Low Battery Acknowledgement
1.
2.
3.
4.
5.
6.
DEFINE PANEL
01:ENTRY DELAY 1
or
31:LOW-BAT ACK
keyfob L-B off 
or
31:LOW-BAT ACK
Repeat steps 1 to 4 of section 4.2 "Entering the Installer Menu".
Select between "keyfob L-B on" and "keyfob L-B off".
You can now press the or button to program any other menu in "
TO EXIT
DEFINE PANEL
".
" or press the button to take you to "
<OK>
56 D-302756
4.11 DEFINE CUSTOM LOCATIONS
This mode allows you to define up to 5 locations (in addition to the locations that can be defined in the ZONES / DEVICES mode - see par. 4.4).
To Define Custom Locations
1.
DEFINE CUSTOM
2.
3.
4.
5.
Key Functionality
CUST. ZONES NAME
EDIT USER TERM 1
EDIT USER TERM 1
Custom 1 
Moves the cursor from left to right. Long press for speed.
Moves the cursor from right to left. Long press for speed.
Scrolls upward the sequence of inserted digits. Long press for speed.
Scrolls downward the sequence of inserted digits. Long press for speed.
Places cursor to extreme right position of edit string and shows the last 16 digits of edit string.
Reverts to previous or top menu without saving the edit string. Reverts to "<OK> TO EXIT" without saving the edit string.
Saves and reverts to previous menu.
Clears all digits to the right of cursor.
Clears one digit by cursor.
Selects between uppercase or lowercase digits.
Repeat steps 1 to 4 of section 4.2 "Entering the Installer Menu".
Enter the first custom location.
Note: The table at the end of this section provides a list of the keys used by the PowerMaster-10 editor.
Press the or button and repeat the procedure for "
USER TERM 2
Pressing the or buttons at any stage in the procedure will take you to “
" - –
EDIT USER TERM 5
<OK> TO EXIT
", as required.
”.
EDIT
4.12 CONFIGURING OUTPUT PARAMETERS
4.12.1 Preliminary Guidance
This mode allows you: a. Events/conditions selection under which PGM (programmable) output will function. b. Selection of the internal siren or STROBE light (that will be activated according to system programming).
D-302756 57
4.12.2 Define PGM
For the PGM output, you can select disable, turn on, turn off or pulse active (turn on for predefined period, selected by PULSE TIME), as follows:
ARM AWAY (upon AWAY arming).  ARM HOME (upon HOME arming).  DISARM (upon disarming).  MEMORY (activated upon registration of an alarm in the memory, turned off upon memory clearing).  DELAY (during exit / entry delays).  KEYFOB (upon AUX button pressing in the keyfob transmitter).
ZONES (by disturbance in each
the PGM output will be turned on upon event occurrence in these zones and will be turned off upon next
event occurrence, alternately.
LINE FAIL: PGM output is ON if telephone line is disconnected.
For PGM devices, you can select the following actions:
FLASH ON ALARM - you can select no flash or all light flash, to control PGM lighting devices in alarm
conditions. LOCKOUT TIME - you can enter daytime limits between which PGM lighting devices controlled by sensors will
be off, even when the associated sensors are triggered.
A. To Configure Output Parameters
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
DEFINE OUTPUTS
PGM: PULSE TIME
pulse time 2s 
PGM: BY ARM AWAY
PGM: BY ARM AWAY
PGM: BY ARM HOME
DEFINE PGM
or
disable 
or
disable 
or
of 3 selected zones, irrespective of arming / disarming). If you select toggle,
Repeat steps 1 to 4 of section 4.2 "Entering the Installer Menu".
There are two sub-menus "DEFINE PGM" and "PGM GENERAL DEF". The PowerMaster-10 display will first read "DEFINE PGM".
Select between "pulse time 2s", "pulse time 30s", "pulse time 2m" and "pulse time 4m"
Select between "disable", "turn ON", "turn OFF" and "pulse active".
Select between "disable", "turn ON", "turn OFF" and "pulse active".
58 D-302756
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
28.
29.
30.
31.
32.
PGM: BY ARM HOME
PGM: BY DISARM
disable 
or
PGM: BY DISARM
PGM: BY MEMORY
disable 
or
PGM: BY MEMORY
PGM: BY DELAY
disable 
or
PGM: BY DELAY
PGM: BY KEYFOB
disable 
or
PGM: BY KEYFOB
PGM: BY ZONES
a - zone
Select between "disable", "turn ON", "turn OFF" and "pulse active".
Select between "disable", "turn ON", "turn OFF" and "pulse active".
Select between "disable", "turn ON", "turn OFF" and "pulse active".
Select between "disable", "turn ON", "turn OFF", "pulse active" and "toggle".
D-302756 59
33.
34.
35.
36.
37.
38.
39.
40.
41.
42.
43.
44.
45.
46.
47.
48.
49.
50.
a – zone Z:00
disable 
or
a - zone
b - zone
b – zone Z:00
disable 
or
b - zone
c - zone
c – zone Z:00
disable 
or
c - zone
PGM: BY ZONES
PGM: BY LINE FAIL
by line fail NO
or
PGM: BY LINE FAIL
Enter the number of the first zone that you designate for activating this output.
Select between "disable", "turn ON", "turn OFF", "pulse active" and "toggle".
Enter the number of the second zone that you designate for activating this output.
Select between "disable", "turn ON", "turn OFF", "pulse active" and "toggle".
Enter the number of the third zone that you designate for activating this output.
Select between "disable", "turn ON", "turn OFF", "pulse active" and "toggle".
Select between "by line fail NO" and "by line failYES".
Pressing the or buttons at any stage in the procedure will take you to “
<OK> TO EXIT
”.
60 D-302756
B. To Configure PGM Lighting Devices in Alarm Conditions and To Set Daytime Limits of Lighting Devices
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
DEFINE OUTPUTS
DEFINE PGM
PGM: GENERAL DEF
FLASH ON ALARM
no flash 
or
FLASH ON ALARM
LOCKOUT TIME
start – HH:MM
TIME 07:00A
start – HH:MM
stop – HH:MM
TIME 07:00P
stop – HH:MM
Repeat steps 1 to 4 of section 4.2 "Entering the Installer Menu".
Select between "no flash" and "all light flash".
Enter the time at which you wish the lockout state to begin (usually at dawn).
Note: AM and PM are selected by pressing respectively.
Enter the time at which you wish the lockout state to end (usually in the evening).
Note: AM and PM are selected by pressing respectively.
Pressing the or buttons at any stage in the procedure will take you to “
<OK> TO EXIT
”.
and ,
and ,
D-302756 61
4.13 Configuring Remote Programming Access Permissions
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
DEFINE COMM.
1:PSTN/GSM
3:C.S. REPORTING
REPORT EVENTS
or
PSTN UP / DOWN
Remote access
rem. access ON
or
Remote access
Mast. downl code
downl.code AAAA
Mast. Downl code
Inst. Downl code
downl.code BBBB
Inst. Downl code
Upload option
Repeat steps 1 to 4 of section 4.2 "Entering the Installer Menu".
Here you give or deny permission to access the system and exercise control from a remote telephone.
Select between "rem. access ON" and "rem. access OFF"
Here you set the master installer 4-digit password for downloading/ uploading data to/from the PowerMaster-10 memory.
Enter the 4-digit master download code ("0000" is not a valid code).
Here you set the installer 4-digit password for downloading data into the PowerMaster-10 memory.
Attention! If "0000" is used, it will not enable connection of the PowerMaster-10 to the PC for upload/download purpose.
Enter the 4-digit installer download code ("0000" is not a valid code).
Here you determine whether the PowerMaster-10 data can be uploaded into a computer while the system is in disarm state or at any time (in HOME/AWAY arming & disarm state).
62 D-302756
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
28.
29.
30.
31.
32
any time 
or
Upload option
Up/Download tel#
Up/Download tel#
PSTN UP / DOWN
GPRS UP / DOWN
My SIM Tel.#
My SIM Tel.#
1st caller ID#
1st caller ID#
2nd caller ID#
Select between "any time" and "when system OFF".
Here you enter the telephone number (up to 16 digits) of the UL/DL server.
Note: Only for use of control panels monitored by compatible Monitoring Stations. Leave empty if not used.
Enter the upload/download software telephone number.
Here you enter the PowerMaster-10 SIM card telephone number. The Monitoring Station dials this number when it needs to connect to the PowerMaster-10 for uploading / downloading data.
Enter the SIM card telephone number.
st
Here you determine the 1 PowerMaster-10 responds to an incoming call from the telephone number defined here, it creates a connection to the IPMP for uploading / downloading data.
Note: Caller ID#1 / ID#2 should be 6 or more digits for wake-up by IPMP to work.
Enter the first IP receiver telephone number.
Here you determine the 2 PowerMaster-10 responds to an incoming call from the telephone number defined here, it creates a connection to the IPMP for uploading / downloading data.
IPMP receiver telephone number. When the
nd
IPMP receiver telephone number. When the
D-302756 63
33.
34.
2nd caller ID#
GPRS UP / DOWN
Enter the second IP receiver telephone number.
You can now press the button to take you to the "
ALARM
" menu (see section 4.7.3.8), or press the button to take
you to "
<OK> TO EXIT
".
RPRT CNFRM
5 DIAGNOSTIC TEST
This mode allows you to test the functionality of all devices of the system and to receive / review information regarding the received signal strength. Communication between system components can also be tested and detailed information is reported. The wireless signal strength measured and reported (see details in the drawing below).
IMPORTANT! Reliable reception must be assured during the initial testing and also throughout subsequent system maintenance. A device should not be installed in location where signal strength is "poor". If you get a "poor" signal strength from a certain device, simply re-locate it and re-test until a "good" or "strong" signal strength is received. This principle should be followed throughout the diagnostic test procedure.
The diagnostic test process is shown below.
5.1 Testing Devices
This section describes how to test or review a device enrolled to the PowerMaster-10 control panel. Note:
It is much easier to test the device while holding the device in your hand, close to the control panel.
5.1.1 Testing all Devices
1.
2.
3.
4.
DIAGNOSTICS
WL DEVICES
TEST ALL DEVICES
TESTING Zxx NNN
TEST KEYFOBS NN
or
ACTIVATE NOW Uxx
Repeat steps 1 to 4 of section 4.2 "Entering the Installer Menu".
(or press the
The PowerMaster-10 system will now perform automatic testing of all enrolled devices in the following order: repeaters, sirens, detectors, keypads.
The PowerMaster-10 system will perform automatic testing of keyfobs (if enrolled) at the end of testing all other devices.
button for "TEST ONE DEVICE".)
64 D-302756
5.1.2 Testing One Device
Note: "Zxx" indicates the type of device and device number that is being tested. "NNN" indicates the number of devices that have not yet been tested.
At this stage if any key is pressed the PowerMaster-10 display will read "
<NEXT> TO END
button to stop the current test and jump to the next test, or,
press the button to continue the test, or, press the button to exit. At the end of the testing procedure the PowerMaster-10 display will read "
SHOW ALL DEVICES
If there are no wireless devices enrolled in the PowerMaster-10
system, the PowerMaster-10 display reads "
Pressing the or buttons at any stage in the procedure will take you to "
" alternating with "
".
<NEXT> TO END
" or “
<OK> TO CONTINUE
NO DEVICES
<OK> TO EXIT
”.
". Press the
".
1.
2.
3.
4.
5.
6.
7.
8.
DIAGNOSTICS
WL DEVICES
TEST ALL DEVICES
TEST ONE DEVICE
CONTACT SENSORS
or
MOTION SENSORS
Zxx:Motion Sens
Front door
TESTING Zxx 001
or
ACTIVATE NOW Uxx
Z01 NOW: STRONG
Repeat steps 1 to 4 of section 4.2 "Entering the Installer Menu".
Select between "CONTACT SENSORS", "MOTION SENSORS", "SMOKE
SENSORS", "KEYFOBS", "SIRENS" or "REPEATERS", for example, "MOTION SENSORS".
The PowerMaster-10 display will read the device name alternating with the location.
The PowerMaster-10 display will read "TESTING Zxx 001" or "ACTIVATE NOW Uxx" for keyfobs.
D-302756 65
Z01 24Hr: EARLY
After testing the PowerMaster-10 display will then automatically change to read the average level for the last 24 hours (for stationary devices) or the number of activations that the control panel has received (for keyfobs).
The signal strength indications are as follows: " "
1-WAY
" (the device operates in 1-way mode, or, the "NOW" communication test failed); " (results are shown without any performed test); " enrolled – not networked); " (result of the last 24Hrs without statistics).
Pressing the or buttons at any stage in the procedure will take you to “
<OK> TO EXIT
NO COM
." (no communication); "
NONE
" (keyfob 24Hr result); or "
”.
5.1.3 Displaying Signal Strength Indication of All Devices
1.
2.
3.
4.
5.
6.
DIAGNOSTICS
WL DEVICES
TEST ALL DEVICES
or
SHOW ALL DEVICES
Z01: 24hr: GOOD
Z01: NOW: NOT TST
K01: 24hr: NONE
K01: NOW: NONE
Repeat steps 1 to 4 of section 4.2 "Entering the Installer Menu".
The PowerMaster-10 display switches between the average signal strength indication for the last 24 hours and the current signal strength indications of the first device type.
Press the next device type.*
The signal strength indications are as follows: " "
1-WAY
" (the device operates in 1-way mode, or, the "NOW" communication test failed); " (results are shown without any performed test); " enrolled – not networked); " (result of the last 24Hrs without statistics).
Pressing the button will display the number and type of device
to which the signal strength indications refer.
Pressing the or buttons at any stage in the procedure will take you to “
button to view the signal strength indications for the
NO COM
<OK> TO EXIT
." (no communication); "
NONE
" (keyfob 24Hr result); or "
”.
STRONG
NOT NET
STRONG
NOT NET
";
GOOD
"; "
POOR
NOT TST
" (device is pre-
EARLY
";
GOOD
"; "
POOR
NOT TST
" (device is pre-
EARLY
";
"
"
";
"
"
66 D-302756
5.1.4 Displaying Signal Strength Indication of RF Devices
1.
2.
3.
4.
5.
6.
DIAGNOSTICS
WL DEVICES
TEST ALL DEVICES
or
SHOW RF PROBLEMS
Z01: 24hr: GOOD
Z01: NOW: NOT TST
K01: 24hr: NONE
K01: NOW: NONE
Repeat steps 1 to 4 of section 4.2 "Entering the Installer Menu".
The PowerMaster-10 display switches between the average signal strength indication for the last 24 hours and the current signal strength indications of the first device type.
Press the next RF device type.*
The signal strength indications are as follows: " "
1-WAY
" (the device operates in 1-way mode, or, the "NOW" communication test failed); " (results are shown without any performed test); " enrolled – not networked); " (result of the last 24Hrs without statistics).
Pressing the button will display the number and type of device
to which the signal strength indications refer.
Pressing the or buttons at any stage in the procedure will take you to “
button to view the signal strength indications for the
<OK> TO EXIT
STRONG
NO COM
." (no communication); "
NONE
" (keyfob 24Hr result); or "
”.
";
NOT NET
GOOD
" (device is pre-
"; "
POOR
NOT TST
EARLY
";
"
"
5.1.5 GPRS Communication Test
The GPRS Communication diagnostic procedure tests GSM/GPRS communication and reports the diagnostic result. In case of communication failure, detailed information of the failure is reported.
1.
2.
3.
4.
D-302756 67
DIAGNOSTICS
WL DEVICES
GSM/GPRS
Repeat steps 1 to 4 of section 4.2 "Entering the Installer Menu".
*
**
The following GSM/ GPRS messages are reported:
Message Description Unit is OK GSM / GPRS is functioning correctly. GSM comm. loss The GSM/GPRS module does not communicate with the Panel Pin code fail Missing or wrong PIN code.
GSM net. fail Unit failed with registration to local GSM network. SIM card fail SIM not installed or SIM card failure. GSM not detected GSM auto enroll failed to detect GSM/GPRS module. No GPRS service The SIM card does not have the GPRS service enabled. GPRS conn. fail Local GPRS network is not available or, wrong setting to GPRS APN, user and/or
Srvr unavailable IPMP Receiver cannot be reached – Check the Server IP IP not defined Server IP #1 and #2 are not configured. APN not defined APN is not configured. SIM card locked After entering a wrong PIN code 3 consecutive times the SIM is locked. To unlock it
Denied by server The IPMP denies the connection request. Check that the Panel is registered to the IPMP
PLEASE WAIT…
UNIT IS OK
(Only if SIM card PIN code is enabled.)
password.
enter a PUK number. The PUK number cannot be entered by the PowerMaster-10.
Receiver.
See the table below for a complete list of possible GSM/GPRS messages.
If there are no wireless devices enrolled in the PowerMaster-10
system, the PowerMaster-10 display reads "
** When the button is pressed the test result takes up to 4 min.
before it is displayed, depending on the severity of the failure.
Pressing the or buttons at any stage in the procedure will take you to “
end of the procedure will take you to the "
<OK> TO EXIT
” or pressing the
NO DEVICES
LAN
" menu.
button at the
".
5.1.6 LAN Connection Test
The LAN Connection diagnostic procedure tests PowerLink Broadband Module communication to the IPMP and reports the diagnostic result. In case of communication failure, detailed information of the failure is reported.
Note: If the PowerLink Broadband Module is not registered to the PowerMaster-10, the menu "
CONNECT.TEST
1.
2.
3.
4.
68 D-302756
" will not be displayed.
DIAGNOSTICS
WL DEVICES
or
LAN
PLEASE WAIT…
UNIT IS OK
Repeat steps 1 to 4 of section 4.2 "Entering the Installer Menu".
*
**
LAN
The following LAN messages are reported:
Message Description
Unit is ok PowerLink Broadband Module is functioning correctly. Test aborted The diagnostic test is aborted, as follows:
Comm. loss The RS-232 serial interface between the PowerLink Broadband Module and the
Rcvr Ip missing Receivers IP 1 and 2 settings are missing in the PowerMaster-10. Cable unplugged The Ethernet cable is not connected to the PowerLink Broadband Module.
Check lan config This message appears in any of the following cases:
Rcvr#1 UnReach.
Rcvr#2 UnReach.
Rcvr#1 UnReg.
Rcvr#2 UnReg.
Broadband Module timeout err.
Invalid result PowerLink Broadband Module responds with a result code that is not recognized
See the table below for a complete list of possible LAN messages. If there are no wireless devices enrolled in the PowerMaster-10
system, the PowerMaster-10 display reads "
** When the button is pressed the test result takes up to 4 min.
before it is displayed, depending on the severity of the failure.
Pressing the or buttons at any stage in the procedure will take you to “
end of the procedure will take you to the "
AC failure – PowerLink Broadband Module is set to OFF mode.
PowerLink Broadband Module has not completed the power-up procedure. In
this case, the installer should wait a maximum of 30 seconds before re­testing.
PowerMaster-10 failed.
Incorrect PowerLink Broadband Module IP has been entered.
Incorrect subnet mask has been entered.
Incorrect default gateway has been entered.
DHCP server failure.
Receiver 1 or 2 is inaccessible, as follows:
Wrong receiver IP has been entered.
Receiver failure.
WAN Network failure.
The PowerMaster-10 unit is not registered to IP receiver 1 or 2.
PowerLink Broadband Module does not respond to test result within 70 sec.
by the PowerMaster-10.
<OK> TO EXIT
” or pressing the
NO DEVICES
".
button at the
LAN RESET OPTION
" menu.
5.1.7 LAN Reset Option
1.
2.
3.
4.
D-302756 69
LAN RESET OPTION
DIAGNOSTICS
WL DEVICES
or
REBOOT
Repeat steps 1 to 4 of section 4.2 "Entering the Installer Menu".
*
To reset the PowerLink Broadband Module
5.
To reset all LAN setting definitions (does not reset Monitoring Station IP definitions)
6.
7.
REBOOT
FACTORY DEFIN.
FACTORY DEFIN.
If there are no wireless devices enrolled in the PowerMaster-10
system, the PowerMaster-10 display reads "
Pressing the or buttons at any stage in the procedure will take you to “
end of the procedure will take you to the "
<OK> TO EXIT
” or pressing the
NO DEVICES
WL DEVICES
" menu.
".
button at the
6 CALLING UPLOAD/DOWNLOAD SERVER
Note:
This option is only used during the installation of panels monitored by compatible Monitoring Stations.
This option allows the installer to initiate a call to the upload/download server. The server uploads the PowerMaster-10 configuration to its data base and can unload predefined parameters to the PowerMaster-10.
To Perform Server Upload/Download
1.
2.
70 D-302756
COMMUNICATING
TEL# NOT DEFINED
DIAL ATTEMPT FAIL
DOWNLOAD FAILED
START UL/DL
DOWNLOADING
DOWNLOAD OK
Repeat steps 1 to 4 of section 4.2 "Entering the Installer Menu".
If the UL/DL server telephone number was already defined (see section
4.7.3.1 "Configuring the Types of Events to be Reported"), the PowerMaster-10 display will read "COMMUNICATING" which is displayed during the dialing process.
If the UL/DL server telephone number was not defined (see section
4.7.3.1 "Configuring the Types of Events to be Reported"), the PowerMaster-10 display will read "TEL# NOT DEFINED" which is displayed for approx. 30 sec. and is followed by a sad (failure) tune.
If communication has been established between the PowerMaster-10 control panel and the upload/download server, the PowerMaster-10 display will read "DOWNLOADING" which is displayed during the dialing process.
If communication has failed between the PowerMaster-10 control panel and the upload/download server, the PowerMaster-10 display will read "DIAL ATTEMPT FAIL" which is displayed for approx. 30 sec. and is followed by a sad (failure) tune.
After the downloaded/uploaded process has been completed successfully, the PowerMaster-10 display will read "DOWNLOAD OK" which is displayed for approx. 30 sec. and is followed by a happy (success) tune.
If communication has been established between the PowerMaster-10 control panel and the upload/download server but the downloaded/uploaded process has failed, the PowerMaster-10 display will read "DOWNLOAD FAILED" which is displayed for approx. 30 sec. and is followed by a sad (failure) tune.
Pressing the or buttons at any stage in the procedure will take you to “
<OK> TO EXIT
”.
7. MAINTENANCE
7.1 Handling System Troubles
Fault What it means Solution
1-WAY The control panel cannot configure or
NOT NETWORKED
MISSING A device or detector has not reported for
JAMMING A radio-frequency signal which is blocking
LOW BATTERY The battery in a sensor, keyfob or wireless
CLEAN ME The fire detector must be cleaned Use a vacuum cleaner to clean the
GAS TROUBLE Gas detector failure Gas detector: Disconnect and then put
control the device. Battery consumption increases.
A device was not installed or not installed correctly, or, cannot establish communication with the control panel after installation.
some time to the control panel.
communication channel of sensors and control panel is detected.
commander is near the end of its useful life.
i) Make sure the device is physically
present.
ii) Check the display for device faults, for
example, low battery.
iii) Use RF diagnostics to check the current
signal strength and during the last 24 hours.
iv) Open the device cover and replace the
battery or press the tamper switch. v) Install the device in a different location. vi) Replace the device.
i) Make sure the device is physically
present. ii) Use RF diagnostics to check the current
signal strength and during the last 24
hours. iii) Open the device cover and replace the
battery or press the tamper switch. iv) Enroll the device again.
i) Make sure the device is physically
present. ii) Check the display for device faults, for
example, low battery. iii) Use RF diagnostics to check the current
signal strength and during the last 24
hours. iv) Replace the battery. v) Replace the device.
Locate the source of interference by switching off any wireless devices (cordless telephones, wireless ear plugs, etc.) in the house for 2 minutes then check if trouble continues.
Use also RF diagnostics to check signal strength.
i) For AC powered devices, check AC
power is available and connected to the
device. ii) Replace the device battery.
detector air vents occasionally to keep them free of dust.
back the AC power supply connector CO Gas detector: Replace the detector
D-302756 71
Fault What it means Solution
SIREN AC FAILURE
AC FAILURE There is no power to gas sensor Make sure that the AC power supply is
GSM NET FAIL The GSM communicator is not able to
RSSI LOW The GSM communicator has detected that
AC SUPPLY FAILURE
COMM. FAILURE A message could not be sent to the
CPU LOW BATTERY
CPU TAMPER The control panel was physically tampered
FUSE TROUBLE The PGM fuse is burnt out or overloaded. Make sure that the connection load
LINE FAILURE There is a problem with the telephone line i) Lift the telephone receiver and make
There is no power to the siren Make sure that the AC power supply is
connect to the cellular network.
GSM network signal is weak There is no power and the system is working
on backup battery power
monitoring station or to a private telephone (or a message was sent but was not acknowledged)
The backup battery within the control panel is weak and must be replaced (see Chapter 7 - Replacing Backup Battery).
with or its cover was opened, or it was removed from wall.
connected properly
connected properly i) Move the Panel and GSM unit to
another location. ii) Enter and exit the installer menu iii) Disconnect GSM unit and install it again iv) Replace SIM card v) Replace the GSM unit
Move the Panel and GSM unit to another location.
Make sure that the AC power supply is connected properly
i) Check telephone cable connection ii) Check that correct telephone number
has been dialed. iii) Dial Monitoring Station to check
whether or not events are received.
i) Check for AC power is available in the
Panel. ii) If trouble exists for more than 72 hours,
replace the battery pack The control panel is not closed properly.
Open the control panel and then close it.
conforms to that specified in the Specifications.
sure a telephone line can be heard
ii) Check the telephone connection to the
control panel
7.2 Dismounting the Control Panel
A. Remove the screw that fastens the front unit to the back unit (see Figure 3.3). B. Remove the 4 screws that fasten the back unit to the mounting surface (see Figure 3.3) and remove the
control panel.
7.3 Replacing the Backup Battery
Replacement and first-time insertion of battery pack is similar (see Figure 3.1). With fresh battery pack, correct insertion and tightened battery compartment lid, the TROUBLE indicator should
extinguish. However, the “MEMORY” message will now blink in the display (caused by the “tamper” alarm you triggered when opening the battery compartment lid). Clear it by arming the system and immediately disarming.
7.4 Fuse Replacement
The PowerMaster-10 has an internal fuse that has automatic reset. Therefore, there is no need to replace the fuse.
When over current condition occurs, the fuse cuts off the circuit current. Upon fault current being removed for several seconds, the fuse is automatically reset and allows current flow through the circuit again.
72 D-302756
7.5 Replacing/Relocating Detectors
Whenever maintenance work involves replacement or re-location of detectors, always perform a full diagnostic test according to section 5.
Remember! A "poor" signal is not acceptable, as stated at the end of the introduction to the test procedure.
7.6 Restoring Factory Defaults
If you want to reset the PowerMaster-10 parameters to the factory default parameters, you should enter the installer menu and perform the "FACTORY DEFLT" function, as detailed below. To get the relevant parameters defaults, contact the PowerMaster-10 dealer.
Note: For PowerMaster-10 with 2 installer codes, INSTALLER code and MASTER INSTALLER code, only the master installer code enables to perform factory default function.
To Reset PowerMaster-10 Parameters to the Factory Default Parameters
1.
2.
3.
4.
FACTORY DEFLT
<OK> to restore
ENTER CODE: 
CODE
PLEASE WAIT…
FACTORY DEFLT
Repeat steps 1 to 4 of section 4.2 "Entering the Installer Menu".
The screen will now prompt you to enter your installer code.
The factory defaults are now restored.
You can now press the or buttons to take you to “
TO EXIT
”.
<OK>
7.7 Viewing the Serial Number
The menu "SERIAL NUMBER" allows reading the system serial number and panel ID for support purposes only. Panel ID is a unique number of the control panel that is used for registering the PowerMaster-10 to IPMP when using GPRS.
To View the Serial Number
1.
2.
3.
4.
D-302756 73
SERIAL NUMBER
JSMivory 0.2.22
Panel ID: 100005
0907030000.
Repeat steps 1 to 4 of section 4.2 "Entering the Installer Menu".
The PowerMaster-10 display will read serial number of the unit.
The PowerMaster-10 display will read the version of the unit.
The PowerMaster-10 display will read the panel ID of the unit.
Pressing the button at any stage in the procedure will take you to "
SERIAL NUMBER
Pressing the or buttons will take you to “
EXIT
”.
".
<OK> TO
8 READING THE EVENT LOG
Events are stored in the event log. You can access this log and review the events, one by one. If the event log fills up completely, the oldest event is deleted upon registration of each new event.
date and time of occurrence are memorized for each event.
The When reading the event log, events are shown in chronological order - from the newest to the oldest. Access to the
event log is provided by pressing the process of the event log is shown below.
8.1 Reading the Event Log
1.
2.
3.
4.
READY 00:00
ENTER CODE: 
LIST OF EVENTS
Z13 alarm
09/02/10 3:37 P
button and not through the installer’s menu. The reading and erasing
While the system is in the normal operating mode, press the Enter the current installer code.
The latest event is shown.
The event is displayed in two parts, for example, "Z13 alarm" then "09/02/10 3:37 P".
Press the
Pressing the or buttons at any stage in the procedure will take you to “
button repeatedly to scroll through the list of events.
<OK> TO EXIT
”.
key.
8.2 Erasing and Exiting the Event Log
5.
6.
7.
8.
Z13 alarm
09/02/10 3:37 P
CLEAR EVENT LOG
<OFF> to delete
<OK> TO EXIT
READY 00:00
From anywhere within the event log, press the
Note: This is applicable only if the installer code entered.
At this stage in the procedure, pressing the will take you to “ the
The system erases the event log and reverts to the normal operating mode.
Pressing the or buttons at any stage in the procedure will take you to “
button will return you to “
<OK> TO EXIT
<OK> TO EXIT
button.
or buttons
” without erasing the event log. Pressing
CLEAR EVENT LOG
”.
”.
74 D-302756
APPENDIX A. Detector Deployment & Transmitter Assignments
A1. Detector Deployment Plan
Zone
No.
1 2 3 4 5 6 7 8
9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28
29 (*) 30 (*)
Zone Types: 1 = Interior follower < 2 = Perimeter < 3 = Perimeter follower < 4 = Delay 1 < 5 = Delay 2 < 6 = 24 h silent Zone Locations: Note down the intended location for each detector. When programming, you may select one of 26 available locations (plus 5 custom locations that you can add – see Zones Devices menu).
* Zones 29 only is hardwired zones.
Zone Type Sensor Location or Transmitter Assignment
<
7 = 24 h audible < 8 = Non-alarm < 9 = Emergency < 10 = Interior < 11 = Home / delay.
(in non-alarm or emergency zones)
Chime
(Yes / No)
D-302756 75
A2. Keyfob Transmitter List
Transmitter Data AUX button Assignments
No. Type Holder Skip exit delay or Arming
1 2 3 4 5 6 7 8
Indicate the desired function (if any)
Skip exit delay F Arming “instant” F
“instant”
A3. Emergency Transmitter List
Tx # Transmitter Type Enrolled to Zone Name of holder
1 2 3 4 5 6 7 8 9
10
A4. Non-Alarm Transmitter List
Tx # Transmitter
1 2 3 4 5 6 7 8 9
10
76 D-302756
Type
Enrolled to Zone Name of holder Assignment
APPENDIX B. Event Codes
B1. Contact ID Event Codes
Code Definition Code Definition
101 Emergency 351 Telco fault 110 Fire 373 Fire detector trouble 120 Panic 381 Loss of supervision RF 121 Duress 383 Sensor tamper 122 Silent 384 RF low battery 123 Audible 393 Fire detector clean me 131 Perimeter 401 O/C by user 132 Interior 403 Auto arm 134 Entry/Exit 406 Cancel 137 Tamper/CP 408 Quick arm 139 Burglary verified 426 Door open event 151 Gas alarm 441 Armed home 154 Flood alarm 454 Fail to close 180 Gas trouble 455 Fail to arm 301 AC loss 456 Partial arm 302 Low system battery 459 Recent close event 311 Battery disconnect 570 Bypass 313 Engineer reset 602 Periodic test report 321 Bell 607 Walk test mode 344 RF receiver jam detect 641 Senior watch trouble 350 Communication trouble
B2. SIA Event Codes
Code Definition Code Definition
AR AC Restore GJ Gas trouble restore AT AC Trouble HA Holdup Alarm (duress) BA Burglary Alarm LR Phone Line Restore BB Burglary Bypass LT Phone Line Trouble BC Burglary Cancel OP Opening Report BR Burglary Restore OT Fail to Arm BT Burglary Trouble / Jamming PA Panic Alarm BV Burglary Verified QA Emergency Alarm BZ Missing Supervision RN Engineer Reset CF Forced Closing RP Automatic Test CI Fail to Close RX Manual Test CL Closing Report RY Exit from Manual Test CP Auto Arm TA Tamper Alarm CR Recent Close TR Tamper Restore EA Door Open WA Flood alarm FA Fire Alarm WR Flood alarm restore FT Fire Detector Clean XR Sensor Battery Restore FJ Fire detector trouble XT Sensor Battery Trouble FR Fire Restore YR System Battery Restore GA Gas alarm YT System Battery Trouble / Disconnection GR Gas alarm restore YX Service Required GT Gas trouble
B3. 4/2 Event Codes
Note: The report to Monitoring Station is on the following zones: First wireless siren - zone 31, second wireless siren ­zone 32, GSM - zone 33.
D-302756 77
Alarms
Zone # 1 2 3 4 567891011121314151617181920212223 24 25 26 27 28 29
1st digit
2nd
digit
4 4 4 4 4444444444455555555 5 5 5 5 5 5 1 2 3 4 56789ABCDEF12345678 9 A B C D E
Restorals
Zone # 1 2 3 4 567891011121314151617181920212223 24 25 26 27 28 29
1st digit
2nd
digit
C C C C CCCCCCCCCCCDDDDDDDD D D D D D D 1 2 3 4 56789ABCDEF12345678 9 A B C D E
Supervisory trouble
Zone # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28
1st digit
2nd digit
6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 7 7 7 7 7 7 7 7 7 7 7 7 7 1 2 3 4 5 6 7 8 9 A B C D E F 1 2 3 4 5 6 7 8 9 A B C D
Low Battery
Zone # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28
1st digit
2nd digit
8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 9 9 9 9 9 9 9 9 9 9 9 9 9 1 2 3 4 5 6 7 8 9 A B C D E F 1 2 3 4 5 6 7 8 9 A B C D
Forced Arming – 8 users
User No. 1 2 3 4 5 6 7 8
1st digit A A A A A A A A
2nd digit 1 2 3 4 5 6 7 8
Zone Bypass
Zone # 1 2 3 4 567891011121314151617181920212223 24 25 26 27 28 29
1st digit
2nd
digit
A A A A AAAAAAAAAAABBBBBBBB B B B B B B 1 2 3 4 56789ABCDEF12345678 9 A B C D E
Panic / 24 Hours - 8 users
User No. 1 2 3 4 5 6 7 8 Panic CP Duress
1st digit 2 2 2 2 2 2 2 2 2
2nd digit 1 2 3 4 5 6 7 8 9 A
2
Arm HOME and AWAY (Closing)
User No. 1 2 3 4 5 6 7 8 Cancel alarm Recent Close
1st digit E E E E E E E E E E
2nd digit 1 2 3 4 5 6 7 8 9 C
Disarm (Opening)
User No. 1 2 3 4 5 6 7 8
1st digit F F F F F F F F
2nd digit 1 2 3 4 5 6 7 8
78 D-302756
Trouble
Event Fuse
1st digit 2 2 2 2 1 1 1 1 1
2nd digit C D E F 1 2 3 4 6
Event CP Tamper
1st digit 1 1 1 1 1 1
2nd digit 7 8 A D E F
Fail
Fuse
Restore
Restore
Jamming Jamming
Restore
No Active COMM. &
AC
Failure
Restore
LINE Restore
AC
CPU
Low
Battery
CPU Low
Battery
Restore
Enter Test Exit Test Auto Test
CP
Tamper
B4. Understanding the Scancom Reporting Protocol Data Format
The SCANCOM data format consists of 13 decimal digits divided into 4 groups, from left to right, as shown at the right side.
Each channel is associated with a specific event as follows:
st
"C": Fire
1
nd
"C": Personal attack
2
rd
"C": Intruder
3
th
"C": Open/close
4
th
"C": Alarm cancel
5
th
"C": Emergency
6
th
"C": Second alarm
7
th
"C": Trouble messages
8
Account
Code
aaaa cccc cccc s
The digit in this position conveys
the status of channel 1
Channels
1 - 4
Channels
5 - 8
The digit in this position conveys
Scancom Data Format
System Status:
no trouble,
test, low battery
the status of channel 8
D-302756 79
APPENDIX C. Glossary
This list of terms is arranged in alphabetical order. Any term indicated by cursive (italic) letters within the explanatory text can be looked up separately.
Abort Period: When an alarm is initiated, the
internal sounder is activated first for a limited period
of time which is the abort period
you cause an alarm accidentally, you can disarm the
system within the abort period before the real sirens
start and before the alarm is reported to the remote
responders.
Alarm: There are 2 kinds of alarm:
Loud alarm
out constantly and the control panel reports the event
by telephone.
Silent alarm
panel reports the event by telephone.
A state of alarm is caused by:
Motion detected by a motion detector
Change of state detected by a magnetic contact
Detection of smoke by a smoke detector
Tampering with any one of the detectors
Pressing the two emergency buttons
Arming: Arming the alarm system is an action that
prepares it to sound an alarm if a zone is “violated”
by motion or by opening a door or window, as the
case may be. The control panel may be armed in
various modes (see AWAY, HOME, INSTANT and
LATCHKEY).
Assigned: Refers to zones.
Associated: Refers to devices.
AWAY: This type of arming is used when the
protected site is vacated entirely. All zones, interior
and perimeter alike, are protected.
Chime Zones: Allow you to keep track of activity in
the protected area while the alarm system is in the
disarmed state. Whenever a chime zone is "opened",
the buzzer beeps twice. The buzzer doesn't beep,
however, upon closing the zone (return to normal).
Residences can use this feature to annunciate
visitors or look after children. Businesses can use it
to signal when customers enter the premises or
when personnel enter restricted areas.
Note: Your installer will never designate a 24-hour
zone or a fire zone as a chime zone, because both
zone types actuate an alarm if disturbed while the
system is in the disarmed state.
Although one zone or more are designated as chime
zones, you can still enable or disable the chime
function.
Communicators: Refers to communication channel,
for example, GSM, PSTN and broadband.
- both internal and external sirens blare
- the sirens remain silent, but the control
detector - a closed window or door is opened
simultaneously (panic).
set by the installer. If
Control Panel: The control panel is a cabinet that incorporates the electronic circuitry and microprocessor that control the alarm system. It collects information from various sensors, processes it and responds in various ways. It also includes the user-interface - control keys, numerical keypad, display, sounder and loudspeaker. Default Settings: Settings that are applicable to a specific device group. Detector: The device (apparatus) that sends an alarm, that communicates with the control panel (e.g. Tower 20 AM is a motion detector, MCT-425 is a smoke detector) Disarming: The opposite of arming - an action that restores the control panel to the normal standby state. In this state, only fire and 24-hour zones will sound an alarm if violated, but a “panic alarm” may also be initiated. Disturbed Zone: A zone in a state of alarm (this may be caused by an open window or door or by motion in the field of view of a motion detector). A disturbed zone is considered “not secured”. Forced Arming: When any one of the system zones is disturbed armed. One way to solve this problem is to find and eliminate the cause for zone disturbance (closing doors and windows). Another way to deal with this is to impose forced arming - automatic de-activation of zones that are still disturbed upon termination of the exit delay. Bypassed zones will not be protected throughout the arming period. Even if restored to normal (closed), bypassed zones will remain unprotected until the system is disarmed.
Permission to “force arm” is given or denied by the installer while programming the system.
HOME: This type of arming is used when people are present within the protected site. A classic example is night-time at home, when the family is about to retire to bed. With HOME arming, perimeter zones are protected but interior zones are not. Consequently, motion within interior zones will be ignored by the control panel, but disturbance of a perimeter zone will cause an alarm. Instant: You can arm the system AWAY-INSTANT or HOME-INSTANT, thereby canceling the entry delay for all delay zones for the duration of one arming period. For example, you may arm the control panel in the HOME-INSTANT mode and remain within the protected area. Only perimeter protection is active, and if you do not expect somebody to drop in while the system is armed, alarm upon entry via the main door is an advantage.
(open), the alarm system cannot be
80 D-302756
To disarm the system without causing an alarm, use your control keypad (which is normally accessible without disturbing a perimeter zone) or use a keyfob transmitter. Latchkey: The Latchkey mode is a special arming mode in which designated "latchkey users" will trigger a "latchkey message" to be sent to a telephone or a pager when they disarm the system.
For example, if a parent wants to be sure that their child has returned from school and disarmed the system. Latchkey arming is only possible when the system is armed in the AWAY mode.
Location: Assigning a named location to a device (e.g. Garage, Front Door etc.) Magnetic Contact Detector, Wireless: A Magnet­controlled switch and a wireless PowerG transmitter in a shared housing. The detector is mounted on doors and windows to detect changes in state (from closed to open and vice versa). Upon sensing that a door or window is open, the detector transmits its unique identification code accompanied by an “alarm” signal and various other status signals to the control panel. The control panel, if not armed at that time, will consider the alarm system as “not ready for arming” until it receives a “restored” signal from the same detector. Motion Detector, Wireless: A passive Infrared motion sensor and a wireless PowerG transmitter in a shared housing. Upon sensing motion, the detector transmits its unique identification code, accompanied by an alarm signal and various other status signals to the control panel. After transmission, it stands by to sense further motion. Non-Alarm Zone: Your installer can designate a zone for roles other than alarm. For instance, a motion detector installed in a dark stairway may be used to switch on lights automatically when someone crosses the dark area. Another example is a miniature wireless transmitter linked to a zone that controls a gate opening mechanism. Quick Arming: Arming without a user code. The control panel does not request your user code when you press one of the arming buttons. Permission to use this arming method is given or denied by the installer while programming the system. Remote Responder: A responder can be either a professional service provider to which the home or business owner subscribes (a Monitoring Station) or a family relation/friend who agrees to look after the protected site during absence of its occupants. The control panel reports events by telephone to both kinds of responders.
Restore: When a detector reverts from the state of alarm to the normal standby state, it is said to have been “restored”. A motion detector restores automatically after detection of movement, and becomes ready to detect again. This kind of “restore” is not reported remote responders. A magnetic contact detector restores only upon closure of the protected door or window. This kind of “restore” is reported Sensor: The sensing element: pyroelectric sensor, photo-diode, microphone, smoke optical sensor etc. Signal Strength: The quality link communication between the system components and the control panel. Smoke Detector, Wireless: A regular smoke detector and a wireless PowerG transmitter in a shared housing. Upon detection of smoke, the detector transmits its unique identification code accompanied by an alarm signal and various status signals to the control panel. Since the smoke detector is linked to a special fire zone, a fire alarm is initiated.
State: AWAY, HOME, AWAY-INSTANT, HOME­INSTANT, LATCHKEY, FORCED, BYPASS.
Status: AC fail, low battery, trouble, etc User Codes: The PowerMaster-10 is designed to
obey your commands, provided that they are preceded by a valid security access code. Unauthorized people do not know this code, so any attempt on their part to disarm or defeat the system is bound to fail. Some operations, however, can be carried out without a user code as they do not degrade the security level of the alarm system. Zone: A zone is an area within the protected site under supervision of a specific detector. During programming, the installer allows the control panel to learn the detector’s identity code and links it to the desired zone. Since the zone is distinguished by number and name, the control panel can report the zone status to the user and register in its memory all the events reported by the zone detector. Instant and delay zones are “on watch” only when the control panel is armed, and other (24-hour) zones are “on watch” regardless of whether the system is armed or not.
Zone Type: The zone type determines how the system handles alarms and other signals sent from the device
.
to the remote responders.
to the
D-302756 81
APPENDIX D. DEFAULT AND PROGRAMMED ZONE
DEFINITIONS
Zone Zone Type Location Chime (melody
No. Default Programmed Default Programmed Location or Off) (*)
1 Delay 1 Front Door 2 Delay 1 Garage 3 Delay 2 Garage Door 4 Perimeter Back Door 5 Perimeter Child Room 6 Interior Office 7 Interior Dining Room 8 Perimeter Dining Room
9 Perimeter Kitchen 10 Perimeter Living Room 11 Interior Living Room 12 Interior Bedroom 13 Perimeter Bedroom 14 Perimeter Guest Room 15 Interior Master Bedroom 16 Perimeter Master Bedroom 17 Perimeter Laundry Room 18 Perimeter Master Bathroom 19 Perimeter Basement 20 24 h /
audible
21 24 h /
audible
22 Emergency Emergency 23 Emergency Emergency 24 24 h / silent Basement 25 24 h / silent Office 26 24 h /
audible
27 24 h /
audible
28 non-alarm Yard 29 non-alarm Hall 30 non-alarm Utility room
Fire
Fire
Attic
Den
* Note: All zones are CHIME OFF by default. Enter your own choice in the last column and program
accordingly.
82 D-302756
Industry Canada Declaration
This product meets the applicable Industry Canada technical specifications/Le présent materiel est conforme aux specifications techniques appliables d’Industrie Canada.
The Ringer Equivalence Number is an indication of the maximum number of devices allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the RENs of all the devices does not exceed five/L’indice d’équivalence de la sonnerie (IES) sert à indiquer le nombre maximal de terminaux qui peuvent être raccordés à une interface téléphonique. La terminaison d’une interface peut consister en une combinaison quelconque de dispositifs, à la seule condition que la somme d’indices d’équivalence de la sonnerie de tous les dispositifs n’excède pas 5.
The Ringer Equivalence Number (REN) for this terminal equipment is 0.3B.
D-302756 83
WARRANTY
Visonic Limited (the “Manufacturer") warrants this product only (the "Product") to the original purchaser only (the “Purchaser”) against defective workmanship and materials under norm al use of the Product for a period of twelve (12) months fr om the date of shipment by the Manufacturer. This Warranty is absolutely cond itional upon the Product having been pro perly installed, maintained and operated under conditions of normal use in accordance with t he Manufacturers recommended installation a nd operation instructions. Products which have become defective for any other reas on, according to the Manufacturers discretion, such as improper installation, failure to follow recommended installation and operational instructions, neglect, willful damage, misuse or vandal ism, accidental damage, alteration or tampering, or repair by anyone other than the manufac turer, are not covered by this Warranty. The Manufacturer does not represent that this Product may not be compromised and/or circumvented or that the Product will prevent a ny death and/or personal injury and/or damage to property resulting from burglary, robber y, fire or otherwise, or that the Product will in all cases provide adequate warning or protectio n. The Product, properly installed and maintained, only reduces the risk of such events without warning and it is not a guarantee or insurance that such events will not occur.
THIS WARRANTY IS EXCLUSIVE AND EXPRES SLY IN LIEU OF ALL OTHER WARRANTIES, OBLIGATIONS OR LIABILITIES, W HETHER WRITTEN, ORAL, EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, OR OTHERWISE. IN NO C ASE SHALL THE MANUFACTURER BE LIABLE TO ANYONE FOR ANY CONSEQUENTIAL OR INCIDENT AL DAMAGES FOR BREACH OF THIS WARRANTY OR ANY OTHER WARRANTIES WHATSOEVER, AS AFORES AID.
THE MANUFACTURER SHALL IN NO EVENT BE LIABLE FOR ANY SPECIA L, INDIRECT, INCIDENTAL, CONSEQUENTIAL OR PUNITIVE DAMAGES OR FOR LOSS , DAMAGE, OR EXPENSE, INCLUDING LOSS OF USE, PROFITS, REVENUE, OR GOODWILL, DIRECTLY OR INDIRECTLY ARISING FROM PURCHASER’S USE OR INABILITY TO USE THE PRODUCT, OR FOR LOSS OR DESTRUCTION OF OTHER PROPERTY OR FROM ANY OTHER CAUSE, EVEN IF MANUFACTURER HAS BEEN AD VISED OF THE POSSIBILITY OF SUCH DAMAGE. THE MANUFACTURER SHALL HAVE NO LIABILITY FOR ANY DEATH, PERSONAL AND/OR BODILY INJURY AND/OR DAMAGE TO PROPERTY OR OTHER LOSS WHETHER DIRECT, INDIRECT, INCIDENTAL, CONSEQUENTIAL OR OTHERWISE, BASED ON A CLAIM THAT THE PRODUCT FAILED TO FUNCTION.
The technical documentation as required by the European Conformity Assessment procedure is kept at: UNIT 6 MADINGLEY COURT CHIPPENHAM DRIVE KINGSTON MILTON KEYNES MK10 0BZ. Telephone number: 0870 7300800,
Fax number: 0870 7300801
However, if the Manufacturer is held liable, whether directly or indirectly, for any loss or damage arising under this limited warranty, THE MANUFACTURER'S MAXIMUM
LIABILITY (IF ANY) SHALL NOT IN ANY CASE EXCEED THE PURCHASE PRICE OF THE PRODUCT, which shall be fixed as liquidated damages and not as a penalty, and shall
be the complete and exclusive remedy against the Manufacturer. When accepting the delivery of the Product, the Purchaser agrees to the said conditions of
sale and warranty and he recognizes ha ving been informed of. Some jurisdictions do not allow the exc lusion or limitation of incidental or consequential
damages, so these limitations may not apply under certain circumstances. The Manufacturer shall be under no liabilit y whatsoever arising out of the corruption and/or malfunctioning of any telecomm unication or electronic equipment or any programs. The Manufacturers obligations under this W arranty are limited solely to repair and/or replace at the Manufacturer’s discretion a ny Product or part thereof that may prove defective. Any repair and/or replacement shall not ex tend the original Warranty period. The Ma nufacturer shall not be responsible for dism antling and/or reinstallation costs. To ex ercise this Warranty the Product must be returned to the Manufacturer freight pre-paid a nd insured. All freight and insurance costs are the responsibility of the Purchaser and are not included in this Warranty.
This warranty shall not be modified, varied or ex tended, and the Manufacturer does not authorize any person to act on its b ehalf in the modification, variation or ex tension of this warranty. This warranty shall apply to the Prod uct only. All products, accessories or attachments of others used in conjunction with the Product, including batteries, shall be covered solely by their own warr anty, if any. The Manufacturer shall not be l iable for any damage or loss whatsoever, whether dir ectly, indirectly, incidentally, consequentia lly or otherwise, caused by the malfunction of the Product due to products, accessories, or attachments of others, including batteries, us ed in conjunction with the Products. This Warranty is exclusive to the original Purchaser and is not assignable. This Warranty is in addition to and does not affect your legal rights. Any provision in this warranty which is contrary to the Law in the state or country were the Product is supplied shall not apply.
Warning:
The user must follow the Manufacturer’s i nstallation and operational instructions
including testing the Product and its whole system at least once a week and to take all necessary precautions for his/her safet y and the protec tion of his/her property.
1/08
VISONIC LTD. (ISRAEL): P.O.B 22020 TEL-AVIV 61220 ISRAEL. PHONE: (972-3) 645-6789, FAX: (972-3) 645-6788 VISONIC INC. (U.S.A.): 65 WEST DUDLEY TOWN ROAD, BLOOMFIELD CT. 06002-1376. PHONE: (860) 243-0833, (800) 223-0020
VISONIC LTD. (UK): UNIT 6 MADINGLEY COURT CHIPPENHAM DRIVE KINGSTON MILTON KEYNES MK10 0BZ.
VISONIC GMBH (D): KIRCHFELDSTR. 118, D-42015 DÜSSELDORF, GERMANY, FAX (0211) 60069619 Email: info-
VISONIC IBERICA: ISLA DE PALMA, 32 NAVE 7, POLÍGONO INDUSTRIAL NORTE, 28700 SAN SEBASTIÁN DE LOS
INTERNET: www.visonic.com
©VISONIC LTD. 2010 POWERMASTER-10 Installer Guide D-302756 Rev 2 (10/10)
FAX: (860) 242-8094
TEL: (0870) 7300800 FAX: (0870) 7300801
dach@visonic.com
REYES, (MADRID), ESPAÑA. TEL (34) 91659-3120, FAX (34) 91663-8468. www.visonic-iberica.es
.
84 D-302756
Fully supervised wireless alarm control system Fully supervised
©Visonic LTD. 2010 PowerMaster-10 English Installer Guide D-302756 Designed by Linor Ankri
www.visonic .com
Loading...