Visonic PMEXPRESS Users Manual

Download

Page 1

PowerMaxExpress

Fully Supervised Wireless Alarm Control System

TABLE OF CONTENTS

1. INTRODUCTION ....................................................... 3

2. SPECIFICATIONS.....................................................3

2.1 General Data....................................................... 3

2.2 RF Section .......................................................... 3

2.3 Electrical Data ..................................................... 3

2.4 Communication ................................................... 4

2.5 Physical Properties .............................................4

3. INSTALLATION .........................................................4

3.1 Unpacking the Equipment................................... 4

3.2 Supplying Power to the Unit................................ 4

3.3 System Planning & Programming.......................4

3.4 Mounting ............................................................. 4

3.5 Wiring .................................................................. 4

3.6 Backup Battery Insertion.....................................6

3.7 Optional GSM Module Mounting ........................... 7

3.8 Power Cable Connection .................................... 7

3.9 Control Panel Final Closure................................7

4. PROGRAMMING.......................................................8

4.1 INTRODUCTION ................................................ 8

4.1.1 General Guidance............................................ 8

4.1.2 Entering an Invalid Installer Code....................... 8

4.1.3 Installer’s Menu................................................ 8

4.1.4 Setting a New Installer Code ...........................8

4.1.5 Setting a New Installer Code in

PowerMaxExpress that has 2 Installer Codes........... 8

4.2 ENROLLING WIRELESS DEVICES AND KEYFOB

TRANSMITTERS........................................................... 9

4.2.1 General Guidance............................................ 9

4.2.2 Enrolling Type .................................................. 9

4.2.3 Enroll/Delete Sensors ......................................9

4.2.4 Enroll/Delete Keyfob Transmitters .........................9

4.2.5 Enroll/Delete Wireless Commander........................ 9

4.2.6 Enroll/Delete 2-Way Keypad ............................ 9

4.2.7 Enroll/Delete Wireless Siren............................. 9

4.3 DEFINING ZONE TYPES, NAMES, CHIME ZONES

& PARTITION ..............................................................11

4.4 DEFINING CONTROL PANEL PARAMETERS .... 12

4.4.1 Preliminary Guidance..................................... 12

4.4.2 Entry Delays 1&2 ............................................. 12

4.4.3 Exit Delay ....................................................... 12

4.4.4 Bell Time ........................................................12

4.4.5 Abort Time...................................................... 12

4.4.6 Alarm Cancel.................................................. 12

4.4.7 Quick Arm ...................................................... 12

4.4.8 Bypass............................................................ 12

4.4.9 Exit Mode .......................................................13

4.4.10 Piezo Beeps................................................. 13

4.4.11 Trouble Beeps.............................................. 13

4.4.12 Panic Alarm.................................................. 13

4.4.13 Swinger Stop................................................ 13

4.4.14 Cross Zoning................................................ 13

4.4.15 Supervision ..................................................13

4.4.16 NOT READY ................................................ 13

4.4.17 AUX Button A ............................................... 13

4.4.18 AUX Button B 2-W-KF....................................13

Installer Guide

4.4.19 Jam Detect................................................... 13

4.4.20 Latchkey....................................................... 14

4.4.21 “Not Active” .................................................. 14

4.4.23 Duress.......................................................... 14

4.4.24 Piezo Siren................................................... 14

4.4.25 Reset Option................................................ 14

4.4.26 Tamper Option............................................. 14

4.4.27 Siren On Line............................................... 14

4.4.28 Memory Prompt ........................................... 14

4.4.29 Disarm Option.............................................. 14

4.4.30 Bell/Rep. Option........................................... 14

4.4.31 Low-Bat Ack................................................. 14

4.4.32 Screen Saver ............................................... 14

4.4.33 Confirm Alarm.............................................. 14

4.4.34 AC FAIL REP............................................... 14

4.4.36 User Permission .......................................... 15

4.4.39 Key Zones Options (Optional) ..................... 15

4.5 DEFINING COMMUNICATION PARAMETERS... 17

Preliminary Guidance.............................................. 17

4.5.1 PSTN / GSM (Fig. 4.5 Detail A)....................... 17

4.5.2 GPRS / BB [Fig. 4.5 Detail B] ........................ 17

4.5.3 C.S. Reporting (Fig. 4.5 Detail C).................. 18

4.5.4 Private Report (Fig. 4.5 Detail D).................... 19

4.6 GSM Auto Detection.............................................. 23

4.7 BBA Auto Detection............................................... 23

4.9 DEFINE CUSTOM................................................. 24

4.10 DIAGNOSTIC TEST............................................ 24

4.11 USER FUNCTIONS ............................................ 25

4.12 RETRIEVING FACTORY DEFAULTS ................ 25

4.13 SERIAL NUMBER ............................................... 25

4.14 CALLING UPLOAD/DOWNLOAD SERVER....... 25

4.15 ENABLING/DISABLING PARTITIONS ............... 26

4.16 WALK-TEST ........................................................ 26

5. TESTING PROCEDURES ...................................... 27

5.1 Preparations...................................................... 27

5.2 Diagnostic Test ................................................. 27

5.3 Keyfob Transmitter Test ................................... 27

5.4 Emergency Transmitter Test ............................ 27

6. MAINTENANCE ...................................................... 27

6.1 Dismounting the Control Panel......................... 27

6.2 Replacing the Backup Battery .......................... 27

6.3 Fuse Replacement............................................ 27

6.4 Replacing/Relocating Detectors ....................... 27

7. READING THE EVENT LOG .................................. 27

APPENDIX A. Detector Deployment & Transmitter

Assignments ................................................................ 29

A1. Detector Deployment Plan.................................. 29

A2. Keyfob Transmitter List....................................... 29

A3. Emergency Transmitter List................................ 30

A4. Non-Alarm Transmitter List................................. 30

D-302017 1

Page 2

APPENDIX B. Event Codes ........................................ 31

Contact ID Event Codes ......................................... 31

SIA Event Codes..................................................... 31

4/2 Event Codes...................................................... 31

Understanding the Scancom Reporting Protocol Data

Format..................................................................... 32

APPENDIX C. Programmable Zone Types ................. 33

C1. Delay Zones....................................................... 33

C2. Emergency Zones.............................................. 33

C3. Fire Zones ........................................................ 33

C4. Flood Zone .......................................................33

C5. Gas Zone.......................................................... 33

C6. Interior Zone ..................................................... 33

C7. Interior Follower Zones .................................... 33

C8. Non-Alarm Zones ............................................. 33

C9. Perimeter Zones............................................... 33

C10. Perimeter Follower Zones.............................. 33

C11. 24-Hour Zones ............................................... 33

APPENDIX D. PowerMaxExpress Compatible Devices

..................................................................................... 34

D1. PowerMaxExpress Compatible Detectors........ 34

D2. PowerMaxExpress Compatible Transmitters... 34

D3. PowerMaxExpress Compatible WL Siren ........ 35

MESSAGE TO THE INSTALLER

The PowerMaxExpress control panel is supplied with 2 instruction manuals:

 Installer Guide (this manual - for your exclusive use)  User’s Guide (for your use during installation only - Must be handed over to the master user after testing the system).

Appendices A.1 and A.2 will help you prepare an installation plan. Please take time to fill out the forms - your job will become much easier and confusion will be prevented. Filling out the forms will also help you create a list of detectors and transmitters that must be obtained for the particular application. Compatible detectors and transmitters are listed and described briefly in Appendix D.

Remember - it is advisable to power up the control panel temporarily after unpacking and program it on the work bench, in accordance with the installation plan.

The programming flow charts in the programming section show all options available for each parameter. Factory defaults are marked with a dark box to their right, and other options (that can be selected instead) are marked by clear boxes. This method allows you to put a checkmark in the appropriate clear box whenever you deviate from the factory defaults.

Most of the programming section paragraph numbers correlate with the programming menu numbers. For example, paragraph 4.4.19 describes the "Jam detect", that exists in menu 4 (define panel), sub-menu 19 (Jam detect).

Although setting the correct time and date is one of the user tasks, we recommend that you set the time and date in the course of programming. Access to the “User Settings” for the installer is possible through item 10 on the installer‘s menu or through the user menu (see User’s manual section 7).

After programming, proceed to install the system as detailed in the Installation Instructions, from paragraph 3.4 onward.

The installer should verify line seizure. Be aware of other phone line services such as DSL. If DSL service is present on the phone line, you must install a filter. It is suggested to use the DSL alarm filter model Z-A431PJ31X manufactured by Excelsus Technologies, or equivalent. This filter simply plugs into the RJ-31X jack and allows alarm reporting without breaking the internet connection.

2 D-302017

Page 3

1. INTRODUCTION

The PowerMaxExpress is a user and installer-friendly, 29zone fully-supervised wireless control system.

IMPORTANT NOTE: Partitioning refers only to purchased control panels that support the partitioning feature.

The PowerMaxExpress includes an optional partition feature. Partitioning allows you to have up to four independently controllable areas with different user codes assigned to each

A partition can be armed or disarmed regardless of

partition. the status of the other partitions within the system. For example, you can define the garage as partition 1, the basement as partition 2, the house as partition 3 and a safe as partition 4. Since each partition is independent of other partitions, you can arm or disarm each partition as desired without altering the states of the other partitions. Therefore, while arming or disarming your home this will not interfere with the safe that you desire to arm most of the time.

2. SPECIFICATIONS

2.1 General Data

Zones Number: 28 wireless zones, 1 hardwired input. Hardwired Zone Requirements: 2.2 kΩ E.O.L. resistance

(max. resistance of wires 220 Ω). Zone Types: Interior follower, interior, perimeter,

perimeter follower, delay 1, delay 2, 24h silent, 24h audible, fire, non-alarm, emergency, gas, flood, temperature and home/delay.

User Codes: 8 codes, 4 digits each (9999 different combinations). Code 0000 is not allowed.

Control Facilities:

- Integral keypad

- PowerCode / Code-Secure™ hand-held transmitters.

- One way / two way keypads.

- SMS commands via optional GSM/GPRS module.

- Remote control by telephone.

Display: Single line, 16-character LCD. Arming Modes: AWAY, HOME, AWAY-INSTANT, HOME-

INSTANT, LATCHKEY, FORCED, BYPASS.

Alarm inhibited during a single arming period (swinger stop) after: 1, 2, 3, alarm/tamper/fault, or not inhibited

(programmable / selectable). Alarm Types: Silent alarm, siren alarm (future option) or

sounder (internal) alarm, in accordance with zone attributes. Siren Signals: Continuous triple pulse - pause - triple pulse...

Siren (bell) Timeout: Programmable (4 min. by default). Internal Sounder Output: At least 85 dBA at 10 ft (3 m). Supervision: Programmable time frame for inactivity alert Special Functions:

- Chime zones

- Diagnostic test and event log.

- Local and Remote Programming over Telephone, GSM /GPRS connections.

- Calling for help by using an emergency transmitter.

- Tracking inactivity of elderly, physically handicapped and

infirm people.

Data Retrieval: Alarm memory, trouble, event log.

(intrusion / 24 hours / panic);

(fire).

The system is designed to function in an appealing way to the user and also offers features that make installers’ life easier than ever before:

EASY TO MAINTAIN

• Alarm memory and trouble data are displayed upon

request.

• Diagnostic test provides visual and audible indication of

the signal level of each detector.

• Remote control from distant telephones.

• Event log stores and displays information.

• Upload / download from distant computer via telephone

line or cellular modem.

QUICK PROGRAMMING

• Simple programming logic, fully menu driven.

• Multiple-choice selection of options for each parameter.

• Unequivocal visual prompts.

• Installer access to the user menu.

Real Time Clock (RTC): The control panel keeps and displays time and date. This feature is also used for the log file by providing the date and time of each event.

Compliance with U.S. Standards: Meets FCC 47 Part 15 and Part 68 requirements.

Compliance with European CE Standards:

EN 50082-1, EN301489-3,7, EN6100-4-6, EN60950, EN300220, EN50130-4, EN50130-5, EN50131-3

The PowerMaxExpress is compatible with the RTTE requirements - Directive 1999/5/EC of the European Parliament and of the Council of 9 March 1999.

According to the European standard EN50131-1, the PowerMaxExpress security grading is 2 – "low to medium risk" and environmental classification is II – "indoor general" and the power supply type is A.

GSM standards:

Europe : Complies with CE standards 3GPP TS 51.010-

1, EN 301 511, EN 50361, EN301489-7 USA: FCC 47 Part 22 (GSM850) and Part 24 (GSM

1900). EMC standard: FCC 47 Part 15. SAR standards: FCC rule 2.1093, FCC Docket 96-326 & Supplement C to OET Bulletin 65

2.2 RF Section

Operating Frequencies (MHz): 315 (in USA & Canada), 433, 868.95 or other UHF channel per local requirement in the country of use.

Receiver Type: Super-heterodyne, fixed frequency Receiver Range: 600 ft (180 m) in open space Antenna Type: Spatial diversity Coding: PowerCode and/or CodeSecure™

2.3 Electrical Data

External AC/AC adapter:

• Europe: 230VAC 50Hz input, 9VAC 700mA output.

• USA: 120VAC 60Hz input, 9VAC 1000mA output.

Current Drain: Approx. 70 mA standby, 1600 mA peak at full load.

Minimum battery voltage: 4.8V

D-302017 3

Page 4

Backup Battery Pack: 4.8V 1300 mAh, rechargeable NiMH battery pack, p/n GP130AAM44MX, manufactured by GP – Backup period of 16 hours.

Maximum battery recharge time: 72 hours Battery Test: Once every 10 seconds.

2.4 Communication

Built-in Modem: 300 baud, Bell 103 protocol Data Transfer to Local Computer: Via RS232 serial port Report Destinations: 2 central stations, 4 private

telephones. Reporting Format Options: SIA, Pulse 4/2 1900/1400 Hz, Pulse 4/2 1800/2300 Hz, Contact ID, Scancom.

3. INSTALLATION

3.1 Unpacking the Equipment

Open the cardboard packing box and check whether all items have been included. If you find out that an item is missing, contact your vendor or dealer immediately.

3.2 Supplying Power to the Unit

Connect power to the PowerMaxExpress temporarily (see figure 3.7). Alternatively, you may power up from the backup battery, as shown in figure 3.3.

Disregard any “trouble” indications pertaining to lack of battery or lack of telephone line connection.

3.3 System Planning & Programming

It pays to plan ahead - use the tables in appendices A and B at the end of this guide to register the intended location of each detector, the holder and assignment of each transmitter.

Pulse Rate: 10, 20, 33 and 40 pps - programmable Message to Private Phones: Tone Ring Detection: The unit does not support ring detection

without DC voltage present on the telephone lines.

2.5 Physical Properties

Operating Temp. Range: 14°F to 120°F (-10°C to 49°C) Storage Temp. Range: -4°F to 140°F (-20°C to 60°C) Humidity: 85% relative humidity, @ 30°C (86°F) Size: 193 x 178 x 50 mm (7-5/8 x 7 x 2 in.) Weight: 658g (23 Oz) (with battery) Color: White

Gather up all transmitters and detectors used in the system and mark each one in accordance with your deployment plan.

Program the system now as instructed in the programming section.

3.4 Mounting

Required tool: Philips screwdriver #2. PowerMaxExpress mounting process is shown in figure

3.1 - 3.8.

3.5 Wiring

Required tools: Cutter and slotted screwdriver - 3 mm blade.

PowerMaxExpress wiring is shown in figure 3.2.

4 D-302017

Page 5

Remove

front

cover

Back unit

Cables entry possibilities

Release

screws

Drill 4 holes and insert wall anchors

Figure 3.1 – Back Unit Mounting

CABLES ROUTING GUIDE

Mark 4 drilling points on mounting surface

Fasten the back unit with 4 screws

Cable clips

(example)

Remove the left or right side

cables entry knockout(s) and

enter the required cable(s).

Remove and use as

cable clamp(s)

D-302017 5

Page 6

Connect telephone cable to SET connector and telephone line cable to LINE connector (through the desired wiring cable entry).

PHONE WIRING

PHONE WIRING IN NORTH AMERICA

BROWN

RED

GREEN

GRAY

RJ-31X

CORD

ZONE & EXTERNAL SIREN WIRING

SITE EXTERNAL SIREN

(FUTURE OPTION)

8-POSITION

RJ-31X PLUG

2.2 k

Alarm

N.C.

RJ-31X JACK

RJ-31X

MAGNETIC CONTACT

OR ANY OTHER

CONTACT

(NOT A DETECTOR)

GRAY

RED

LINE

HOUSE

FROM

PHONES

STREET

GRN

BROWN

Figure 3.2 - Wiring

WARNING! When plugging SIREN & ZONE terminals

back into place, be sure to align them carefully with the pins on the PCB. Misaligned or reverse insertion of

3.6 Backup Battery Insertion

Connect battery pack as shown in the next drawing.

terminals may damage internal PowerMaxExpress circuits!

6 D-302017

Page 7

Battery

insertion

Battery connection

Figure 3.3 - Battery Insertion

3.7 Optional GSM Module Mounting

Note: The GSM module is used with an internal antenna. Optional external antenna can be used. Caution: Do not install or remove the GSM module when the system is powered by AC power or backup battery.

1. Plug in the

GSM Module and fasten it as follows:

3.8 Power Cable Connection

Connect the power cable and close the control panel as shown below. Electrical socket-outlet shall be installed near the equipment and shall be easily accessible.

Connect the power

adapter to the

power connector.

Fig. 3.6 - Power Cable Connection

3.9 Control Panel Final Closure

Control panel final closure is shown below.

front

cover

Figure 3.4 - Optional GSM Module

Mounting

2. Insert the SIM card into the GSM module

SIM card insertion

Slide top

cover

Slide SIM

card into

cover

Open cover

Rotate cover

to close

Lock cover

to close

Figure 3.5 - SIM Card insertion

Align SIM

card in cover

(note cover orientation)

IMPORTANT

Do not insert or remove SIM card when the control panel is powered by AC power or battery.

GSM

Front unit

Fasten screws

Figure 3.7 - Final Closure

D-302017 7

Page 8

4. PROGRAMMING

4.1 INTRODUCTION

4.1.1 General Guidance

We recommend to program the PowerMaxExpress on the work bench before actual installation. Operating power may be obtained from the backup battery or from the AC power supply.

The installer’s menu is accessible only to those who know the installer’s 4-digit code, which is 9999 by factory default.

Note: Access to the installer menu, in PowerMaxExpress that has "User Permission" enabled (for example in UK) is accessible only at the end of the user menu. This option can be changed if necessary (see par. 4.4.36).

For PowerMaxExpress that has 2 installer codes (not applicable in UK), the default INSTALLER code is 8888 and the default MASTER INSTALLER code is 9999. The following actions can be done only by using the master installer code:

• Changing master installer code.

• Resetting the PowerMaxExpress parameters to the

default parameters,

• Defining specific communication parameters, as detailed in a note in figure 4.5C.

Obviously, you are expected to use this code only once for gaining initial access, and replace it with a secret code known only to yourself.

You will mainly use 5 control pushbuttons during the entire programming process:

- to move one step forward in a menu.

- to move one step backward in a menu.

OKI

to enter the relevant menu or confirm data.

- to move one level up in a menu.

- to return to the "OK TO EXIT" state.

The sounds you will hear while programming are:

- Single beep, heard whenever a key is pressed.

- Double beep, indicates automatic return to the normal operating mode (by timeout).

- Happy Melody (- - - –––), indicates successful

☺

completion of an operation.

- Sad Melody (–––––), indicates a wrong move



or rejection.

4.1.2 Entering an Invalid Installer Code

If you enter an invalid installer code 5 times, the keypad will be automatically disabled for 90 seconds and the message WRONG PASSWORD will be displayed.

4.1.3 Installer’s Menu

The installer's menu is shown in figure 4.1a. The text in rectangles represents the current PowerMaxExpress display.

4.1.4 Setting a New Installer Code

To set an installer code, perform the actions that are presented in figure 4.1b. When you are instructed to enter code, enter a 4-digit code.

4.1.5 Setting a New Installer Code in PowerMaxExpress that has 2 Installer Codes

For PowerMaxExpress with 2 installer codes, INSTALLER code (default 8888) and MASTER INSTALLER code (default 9999), set new codes as shown in figure 4.1c. For details regarding the different authorization levels when logging in with installer code and master installer code, refer to the note inside figure 4.5C (DEFINE COMM). By using the master installer code, the menu enables changing both master installer code and installer code. By using the installer code, the menu enables changing the installer code only.

(*) Applicable only when "USER PERMIT" function is enabled

(see par. 4.4.36 - USER PERMIT)

(**) Optional feature.

Figure 4.1b - Setting a New Installer Code (see note)

(First display)

READY 00:00

WALK TEST

USER SETTING

INSTALLER MODE

ENTER CODE

[installer code]

1. NEW INSTL CODE

2. ENROLLING

3. DEFINE ZONES

4. DEFINE PANEL

5. DEFINE COMM.

9. DEFINE CUSTOM

10. DIAGNOSTICS

11. USER SETTINGS

12. FACTORY DEFLT

13. SERIAL NUMBER

14. START UL/DL

(**)

15. PARTITIONING

<OK> TO EXIT

Figure 4.1a - Installer’s Menu

(See fig . 4.1a )

1. NEW INSTL CODE

NEW INST. CODE

INST. CODE xxxx

[code]

(*)

(See fig. 4.1b & 4.1c)

(See figure 4.2)

(See figure 4.3)

(See figure 4.4)

(See figure 4.5)

(See figure 4.9)

(See figure 4.10)

(See chapter 7 in User Guide)

(See par. 4.12) (Control Panel

serial number display)

(See section 4.14)

(See figure 4.15)

8 D-302017

Page 9

By using

INSTALLER CODE

(see fig. 4.1a)

1. NEW INSTL CODE

NEW INST. CODE

INST. CODE xxxx

[code]

MASTER INSTALLER CODE

(see fig. 4.1a)

1. NEW INSTL CODE

NEW MASTER CODE

MASTER CODE xxxx

[code]

By using

NEW INST. CODE

INST. CODE xxxx

[code]

Note: Installer Code should never be programmed as “0000”. Doing so will lock the user out of the installer menu!

Figure 4.1c - Setting a New Installer Code

in System with Inst. & Master Inst. Codes (see note)

4.2 ENROLLING WIRELESS DEVICES AND KEYFOB TRANSMITTERS

4.2.1 General Guidance

The ENROLLING mode has the following sub-modes:

• ENROLLING TYPE (wireless devices)

• ENROLL SENSORS.

• ENROLL

KEYFOB (multi-button CodeSecure

transmitters)

• ENROLL WL 1WAY KP (wireless commander MCM-140+)

• ENROLL WL 2WAY KP (wireless 2-way keypad MKP-150/

MKP-151)

• ENROLL WL SIREN (wireless siren) Before beginning, gather all the devices that you intend to enroll and make sure they all have batteries installed. Your control panel must recognize the unique identification code (ID) of each such device in order to supervise them, receive their signals and respond accordingly.

Attention! CodeSecure transmitters are mainly used for arming/disarming and can not be enrolled to zones. In

order to enroll to zones, use only non-CodeSecure wireless devices.

4.2.2 Enrolling Type

Here you determine whether to enroll a wireless device by normal transmission or by device Tamper function (opening its cover). Options: normal, or by tamper.

4.2.3 Enroll/Delete Sensors

Wired detector can be enrolled in zone 29 and wireless detectors can be enrolled in zones 01-28.

STOP

• Make sure that magnetic contact transmitter is

To enroll / delete wired / wireless sensors, refer to Fig. 4.2.

• Before enrolling, the lens at the front of PIR

and dual-technology sensors should be masked to prevent inadvertent transmission.

together with its magnet, to prevent it from sending alarm transmission.

4.2.4 Enroll/Delete Keyfob Transmitters

Keyfob transmitters are multi-button wireless CodeSecure™ transmitters. Eight system users use them for better, quicker and safer control over various system functions. To enroll / delete 1-way or 2-way keyfob transmitters, refer to figure 4.2.

4.2.5 Enroll/Delete Wireless Commander

The Wireless Commander (MCM-140+) is a remote control unit that enables the user to remotely control the system. To enroll / delete up to 8 wireless commanders, refer to figure 4.2 (Enroll WL 1-way KP).

4.2.6 Enroll/Delete 2-Way Keypad

The 2-way keypad, type MKP-150/MKP-151, enables the user to remotely control the system and also to receive data from the system (alarm and trouble data). To enroll up to two 2-way keypads, refer to figure 4.2.

4.2.7 Enroll/Delete Wireless Siren

The wireless siren is a remote siren that is activated upon predefined events by the PowerMaxExpress system. To enroll / delete up to 2 wireless sirens, refer to figure 4.2.

D-302017 9

Page 10

ENROLLING TYPE

normal enroll by tamper

(First display is READY or NOT READY)

READY 00:00

NORMAL MODE

USER SETTINGS

INSTALLER MODE

ENTER CODE

[installer code]

1. NEW INSTL CODE

2. ENROLLING

3. DEFINE ZONES

ENROLL SENSORS

SET SENSITIV.

higher sensitivity lower sensitivity

Select by



ZONE No: - -

[wired Zone No.



29/30] (e.g. 29)

ZONE No: 29

<OK> TO ENROLL

ZONE No: 29

for next

enrolling action

Enrolling wired sensor

ENROL WL 1WAY KP

1way kp No :

1way kp No : 5 1way kp No : 5

[WL Zone No.



01-28] (e.g. 05)

ZONE No: 05

TRANSMIT NOW

[Initiate transmission)

(**)

ZONE No: 05

for next

enrolling action

Enrolling a WL Sensor

[WL 1-way keypad No. 1 to 8] (e.g. 5)



(***)

(****)

[wired/WL Zone No.

01-30] (e.g. 05)

ZONE No: 05

<OFF> TO DELETE

ZONE No: 05

Deleting wired/

WL sensor

(**)

2way kp No : 2 2way kp No : 2

(*)

Keyfob No: 5

TRANSMIT NOW

Partition

Partition 1

[select partition 1 - 4]

KEYFOB No: 05

for next

enrolling action

Enrolling a Keyfob

ENROL WL 2WAY KP

(*****)



2way kp No:



No. 1 or 2] (e.g. 2)

ENROLL KEYFOB

Keyfob No: -

[Keyfob No.]

(e.g. 5)

Keyfob No: 5

<OFF> TO DELETE

(press

any key)

(**)

KEYFOB No: 05

Deleting a Keyfob

Note:

Applies only

when in Partition mode

[MKP-150/151

(**)

<OK> TO EXIT

TRANSMIT NOW

press

key until red LED

lights

Partition



Partition 1

[select partition 1 - 4]



1way kp No: 5

for next

enrolling action

Enrolling a wireless

Commander MCM-140+

ENROL WL SIREN



SIREN No :



siren No : 2 siren No : 2

TRANSMIT NOW

Momentarily press the wireless siren self-test button until a squawk is heard (1 sec. approx.)

siren No: 2

for next



enrolling acti on

Enrolling a

wireless siren

<OFF> TO DELETE

1way kp No: 5

Deleting a wireless

Commander MCM-140+

Note:

Applies only

when in Partition mode

[WL siren No.

1 or 2] (e.g. 2)

Open WL siren cover and remove its battery

<OFF> TO DELETE

siren No: 2

Deleting a

wireless siren

inst. instructions)

Enrolling a wireless

keypad MKP-150/151

(**)

Press MKP-

150/151 back tamper switch once

(see MKP-

150/151

2way kp No: 2

for next



enrolling action

AWAY

keypad MKP-150/151

Figure 4.2 - Enrolling / Deleting Wireless Devices / Keyfobs / Wireless Commanders / Wireless Sirens

* Keyfob enrolling can be performed by the installer or by

the user (via USER SETTINGS menu).

** A black box in the display means that a device is

enrolled (the system has learned its ID). No black box indicates that the device is not enrolled.

*** Initiate either normal transmission or the device

tamper function (see ENROLLING TYPE, Par. 4.2.2).

**** Select "higher" sensitivity for far wireless device,

"lower" for near devices.

***** MKP-150/151 is not compatible for use when partition

is enabled.

<OFF> TO DELETETRANSMIT NOW

2way kp No: 2

Deleting a wireless

10 D-302017

Page 11

4.3 DEFINING ZONE TYPES, NAMES, CHIME ZONES & PARTITION

This mode allows you to assign one of 15 zone types to each of the system's 29 (wireless & wired) zones. In addition, it also allows you to assign a name to each zone and determine whether the zone will operate as a chime zone (only while the system is in the disarmed

or Home arming state). When a chime zone is triggered, chime melody or zone name is heard (there are 2 selectable chime modes - Melody chime or Chime Off).

Refer to Figure 4.1a

to gain access to

USER SETTINGS

INSTALLER MODE

ENTER CODE

[installer code]

ENROLLING

3. DEFINE ZONES

ZONE No: - -

[Zone No.] (e.g. 05)

Zxx: TYPE -

31 zone names can be selected, 26 fixed names and 5 custom names (defined by the installer - see chap. 4.9):

Attic Back door Basement Bathroom Bedroom Child room Closet Den

Dining room Downstairs Emergency Fire Front door Garage Garage door Guest room

A list of factory defaults is printed in table 1. You may fill out the blank columns even before you start and proceed to program according to your own list.

Remember!

A delay zone is also a perimeter zone by definition.

Zone types are fully explained in Appendix C.

Selectable Zone Names

Hall Kitchen Laundry room Living room Master bath Master bdrm Office Upstairs

OPTIONAL

Zxx: KEY ON/OFF

(**)

Utility room Yar d Custom 1 Custom 2 Custom 3 Custom 4 Custom 5

Zxx: NAME - -

<OK> TO EXIT

1. Inter-follow

2. Perimeter

3. Perim-follow

4. Delay 1

5. Delay 2

6. 24h silent

7. 24h audible

8. Fire

9. Non-alarm

10. Emergency

11. Ga s

12. Flood

13. Interior

14. Temperature

15. Home/Delay (*)

Figure 4.3 - DEFINE ZONES Flow Chart

z-key enable z-key disable

(*)

Zxx: CHIME

Melody-chime Chime off

(*)

Attic Back door Basement Bathroom Bedroom Child room Closet

(see list above)

(*)

(see note)

Zxx: PARTITION

Partition 1 Partition 2 Partition 3 Partition 4

(*)

* The currently saved option is displayed with a dark box at the right side. To review the options, repeatedly click

button, until the desired option is displayed, then click

** Clicking the

OKI

button in this location brings you to the same zone number that you are dealing with. Press or

OKI

(a dark box will be displayed at the right side).

to select the next zone.

Table 1 - DEFAULT AND PROGRAMMED ZONE DEFINITIONS

Zone Zone Type Zone Name Chime (melody

No. Default Programmed Default Programmed Zone Name or Off) (*)

1 Delay 1 Front Door 2 Delay 1 Garage 3 Delay 2 Garage Door 4 Perimeter Back Door 5 Perimeter Child Room 6 Interior Office 7 Interior Dining Room 8 Perimeter Dining Room 9 Perimeter Kitchen

D-302017 11

Page 12

Zone Zone Type Zone Name Chime (melody

No. Default Programmed Default Programmed Zone Name or Off) (*)

10 Perimeter Living Room 11 Interior Living Room 12 Interior Bedroom 13 Perimeter Bedroom 14 Perimeter Guest Room 15 Interior Master Bedroom 16 Perimeter Master Bedroom 17 Perimeter Laundry Room 18 Perimeter Master Bathroom 19 Perimeter Basement 20 Fire Fire 21 Fire Fire 22 Emergency Emergency 23 Emergency Emergency 24 24 h / silent Basement 25 24 h / silent Office 26 24 h / audible Attic 27 24 h / audible Den 28 non-alarm Yard 29 non-alarm Hall 30 non-alarm Utility room

* Note: All zones are CHIME OFF by default. Enter your own choice in the last column and program accordingly.

4.4 DEFINING CONTROL PANEL PARAMETERS

4.4.1 Preliminary Guidance

This mode allows you to customize the control panel and adapt its characteristics and behavior to the requirements of the particular user. An illustrated process is shown in Figure 4.4. In this illustration, each selected option is displayed with a dark box at the right side. To review the options, repeatedly click the desired option is displayed, then click SHOW/OK

button

button, until

4.4.2 Entry Delays 1&2

(Fig. 4.4, location 01, 02). Two different entry delays allow the user to enter the protected site (while the system is in the armed state) via 2 specific doors and routes without causing an alarm.

Following entry, the user must disarm the control panel before the entry delay expires. Slow-rate warning beeps start sounding once the door is opened, until the last 10 seconds of the delay, during which the beeping rate increases. Locations No. 1 (entry delay 1) and 2 (entry delay 2) allow you to program the length of these delays. Available options for each delay are: 00s, 15s, 30s, 45s, 60s, 3m and 4m.

4.4.3 Exit Delay

(Fig. 4.4 location 03). An exit delay allows the user to arm the system and leave the protected site via specific routes and doors without causing an alarm. Slow-rate warning beeps start sounding once the arming command has been given, until the last 10 seconds of the delay, during which the beeping rate increases. Location No. 3 allows programming of the exit delay length. Available options are: 30s, 60s, 90s, 120s, 3m, and 4m.

4.4.4 Bell Time

(Fig. 4.4, location 04). Here you select the length of time the bell (or siren) is allowed to function upon alarm. The bell time starts upon activation of the siren. Once the bell time expires, the siren is automatically shut down.

Available options are: 1, 3, 4, 8, 10, 15 and 20 minutes.

Note: Bell Time is defined for the entire alarm system.

12 D-302017

However, when disarming any partition (in a PowerMaxExpress Partition system) the siren ceases to sound.

4.4.5 Abort Time

(Fig. 4.4 location 05). Here you select the length of time allowed by the system to abort an alarm (not applicable to alarms from FIRE, 24H SILENT, EMERGENCY, GAS, FLOOD and TEMPERATURE zones). The PowerMaxExpress is programmed to provide an “abort interval” that starts upon detection of an event. During this interval, the buzzer sounds a warning but the siren remains inactive and the alarm is not reported. If the user disarms the system within the allowed abort interval, the alarm is aborted.

Available options are: 00s, 15s, 30s, 45s, 60s, 2m, 3m and 4m.

4.4.6 Alarm Cancel

(Fig. 4.4, location 06). Here you determine the ”cancel

alarm” period that starts upon reporting an alarm to the central station. If the user disarms the system within that time period, a “cancel alarm” message is sent to the central station.

Available options are: 1, 5, 15, 60 minutes, 4 hours and also cancel inactive.

4.4.7 Quick Arm

(Fig. 4.4, location 07). Here you determine whether the user will be allowed to perform quick arming or not. Once quick arming is permitted, the control panel does not request a user code before it arms the system.

The two options are: quick arm ON and quick arm OFF.

4.4.8 Bypass

(Fig. 4.4, location 08). Here you permit either manual bypassing of individual zones (through the USER SETTINGS menu), or allow the system to "force arm" (perform automatic bypassing) of open zones during the exit delay. If desired, press the arming key again if you want to eliminate the protest tone that sounds during forced arming. If a zone is open and forced arming is not

Page 13

permitted, “NOT READY” is displayed and the system does not arm (the “Sad Melody” will sound). If "no bypass" is selected, neither manual bypassing nor force arming is allowed.

Options: manual bypass, force arm and no bypass.

4.4.9 Exit Mode

(Fig. 4.4, location 09). Here you determine exit mode options. Three types of exit modes are available: Restart Exit - Exit delay restarts when the door is reopened during exit delay. The restart occurs once only. Restarting the exit delay is helpful if the user re-enters immediately after going out to retrieve an item that he left behind. Off by door - When the door is closed, the exit delay is automatically terminated (even if the defined exit delay was not completed). Normal - The exit delay is exactly as defined, regardless of whether the door is open or closed.

4.4.10 Piezo Beeps

(Fig. 4.4, location 10). Here you determine whether warning beeps will sound or muted during exit and entry delays. An additional option is to mute the warning beeps only when the system is armed “HOME”.

Options: enable beeps, off when home and disable beeps.

4.4.11 Trouble Beeps

(Fig. 4.4, location 11). Under trouble conditions, the sounder emits a series of 3 short beeps once per minute. Here you determine whether this special beeping sequence will be active, inactive, or just inactive at night (the range of “night” hours is defined in the factory). The 3 options are: enable beeps, off at night (8 PM through 7 AM) and disable beeps.

4.4.12 Panic Alarm

(Fig. 4.4, location 12). Here you determine whether the user will be allowed to initiate a panic alarm by simultaneous pressing either the two panic buttons keypad / wireless commander) or away + home keyfob transmitter). Audible panic activates the siren and simultaneously transmits a message via telephone. Silent panic only transmits a message via telephone. The options are: silent panic, audible panic and disable panic.

(on the

(on a

4.4.13 Swinger Stop

(Fig. 4.4, location 13). Here you determine the number of times each zone is allowed to initiate an alarm within a single arming period (including tamper & power failure events of detectors, PowerMaxExpress, wireless siren, etc.). If the alarms number from a specific zone exceeds the programmed number, the control panel automatically bypasses the zone to prevent recurrent siren noise and nuisance reporting to the central station. The zone will be reactivated upon disarming, or 48 hours after having been bypassed (if the system remains armed).

Available options are: shut after 1, shut after 2, shut after 3 and no shutdown.

Note: Swinger Stop is defined for the entire alarm system and not per partition (in a PowerMaxExpress Partition system).

4.4.14 Cross Zoning

(Fig. 4.4, location 14). Here you determine whether cross zoning will be active or inactive. Cross zoning is a method used to counteract false alarms - an alarm will not be initiated unless two adjacent zones are violated within a 30-second time limit.

This feature is active only when arming AWAY and only with zone couples from zone No. 18 to 27 and 21, etc.). You may use any one of these zone couples to create a “cross-zoned” area.

Note: If one of two crossed zones is bypassed (see Para.

4.4.8), the remaining zone will function independently. Note: Every 2 crossed zones must be of the allowed zone type (Interior, Perimeter, Perimeter follower).

The options are: cross zone ON and cross zone OFF.

Cross zoning is not applicable in Entry/ Exit zones and 24h zones (Fire, Emergency, 24h audible, 24h silent).

(18 and 19, 20

4.4.15 Supervision

(Fig. 4.4, location 15). Here you determine the time limit for reception of supervision reports from various supervised wireless devices. If any device does not report at least once within the selected time limit, an “INACTIVITY” alert is initiated.

The options are: 1, 2, 4, 8, 12 hours and disable.

4.4.16 NOT READY

(Fig. 4.4, location 16). Here you determine if the system will be in NOT READY status when there is a supervision failure. In the "in supervision" mode, the system will be in NOT READY status if during the last 20 minutes a supervision message was not received. Options: normal and in supervision.

Note: NOT READY operates only per partition (in a PowerMaxExpress Partition system).

4.4.17 AUX Button A

(Fig. 4.4, location 17). Here you select the function of the AUX button/ button A on keyfob transmitters MCT-234, MCT-237 and wireless commanders MCM-140+. Four options are offered for each AUX button: Instant: Pressing the AUX button while the exit delay is in progress will cause the system to arm “instant” (the entry delay is canceled). Skip exit delay: Pressing the AUX button will immediately cause the system to arm immediately.

4.4.18 AUX Button B 2-W-KF

(Fig. 4.4, loc. 18). Applicable only for 2-way keyfob MCT-237. Same as 4.4.17 but for AUX button B.

4.4.19 Jam Detect

(Fig. 4.4, location 19). Here you determine whether jamming (interfering transmissions, on the radio channel used by the system) will be detected and reported or not. If a jam detection option is selected, the system does not allow arming under the relevant jamming conditions.

Option Detection and Reporting when

UL (20/20)

(USA standard)

EN (30/60)

(Europe standard)

class 6 (30/60) (British standard)

Disabled (No jamming detection and reporting).

Jam Detection Options

There is continuous 20 seconds of jamming There is an accumulated 30 seconds of jamming within 60 sec. Like EN (30/60) but the event will be reported only if the jamming duration exceeds 5 minutes.

D-302017 13

Page 14

4.4.20 Latchkey

(Fig. 4.4, location 20). Here you determine whether the system can be armed in the latchkey mode. If the system is armed this way, a “latchkey” message will be sent to specific telephones upon disarming by a “latchkey user” (users 5-8 or keyfob transmitters 5-8). This mode is useful when parents at work want to be informed of a child’s return from school. You can record a name for latchkey users. The options are: Latchkey ON and Latchkey OFF.

4.4.21 “Not Active”

(Fig. 4.4, location 21). Here you determine the time limit for reception of signals from sensors used to monitor the activity of sick, elderly or disabled people. If no sensor detects and reports movement at least once within the defined time limit, a “not-active” alert is initiated.

Options: 3, 6, 12, 24, 48, 72 hours and no act disable.

Note: The Not Active timer is defined for the entire alarm system for the above hour options and not per partition (in a PowerMaxExpress Partition system). Subsequently, a dedicated timer is assigned to each partition.

4.4.23 Duress

(Fig. 4.4, loc. 23).

be sent to the central station if the user is forced to disarm the system under violence or menace. To initiate a duress message, the user must disarm the system with the duress code (2580 by default). Here you can change the code digits or enter "0000" to disable the duress feature. The

system does not allow the user to program the duress code saved in this memory location as an existing user code.

A duress alarm (ambush) message can

4.4.24 Piezo Siren

(Fig. 4.4, location 24). Here you determine whether the

internal siren will sound or remain silent upon alarm (according to the user preference). Options: piezo siren on, piezo siren off.

4.4.25 Reset Option

(Fig. 4.4, location 25). (Not applicable in the USA)

Here you determine whether the system can be rearmed (after an event) by the user or only by the installer. Options: user reset or engineer reset. If Engineer Reset is selected, the system can be rearmed only by the installer menu, by entering and exiting the event log (see section 7), or by remote telephone. To perform Engineer Reset via the telephone, establish communication with the PowerMaxExpress (see user guide, par. 6.3A, steps 1-5) and continue as follows:

a.  [*], [installer code], [#] b. Wait for 2 beeps c.  [*], [1], [#] d.  [*], [99], [#] Note: This menu is not available when partition is enabled.

; by entering and exiting the installer

4.4.26 Tamper Option

(Fig. 4.4, location 26).

tamper will be reported or ignored. Available options are: zone tamper ON and zone tamper OFF.

Here you determine whether zone

4.4.27 Siren On Line

(Fig. 4.4, location 27).

siren will be activated or not when the telephone line fails during system armed state. Available options are: enable on fail, disable on fail.

Here you determine whether the

4.4.28 Memory Prompt

(Fig. 4.4, location 28). Here you determine whether the user

will receive indication that an alarm has been activated. Available options are: enable and disable.

4.4.29 Disarm Option

(Fig. 4.4, location 29). Here you determine when it is possible

to disarm the system: A. Any time. B. In AWAY mode, during entry delay, by using the

PowerMaxExpress keypad or wireless sensor (keyfob).

C. In AWAY mode, during entry delay, by using a wireless

device (keyfob) only (this is set as a default in UK to comply with DD243).

D. During entry delay, or by using the PowerMaxExpress

keypad in AWAY mode. Options: any time, on entry all, on entry wireless, or entry + away kp.

4.4.30 Bell/Rep. Option

(Fig. 4.4, location 30). Here you determine whether an

alarm will be initiated (siren / report) when there is a supervision / jamming failure during AWAY arming state. Available options are: EN standard and other. When "EN standard" is selected, if there is supervision / jamming failure during AWAY arming, the siren is activated and the events are reported as tamper events. When "Other" is selected, there is no such activity during AWAY arming.

4.4.31 Low-Bat Ack

(Fig. 4.4, location 31). Here you determine whether the user

will hear or will not hear low battery sound when he tries to disarm the system with a keyfob whose battery voltage is low. Available options are: keyfob L-B on (the user has to acknowledge the keyfob low battery message) or keyfob L-B off (the user does not have to acknowledge the keyfob low battery message).

4.4.32 Screen Saver

(Fig. 4.4, location 32). Here you can determine that if no

key is pressed during more than 30 seconds, the display will be “PowerMax” (to prevent possible intruder of knowing the system status). You can determine that

normal display will return after pressing the button followed by entering user code (Refresh by Code)

or after pressing any key (Refresh by Key). If Refresh by Key is selected, the first pressing of any key

(except Fire and Emergency) will cause normal display return and the second press will perform the key function. Regarding the Fire and Emergency keys, the first key press will cause normal display return and also will perform the Fire/Emergency function.

Options: scrn saver OFF, refresh by code, refresh by key.

4.4.33 Confirm Alarm

(Fig. 4.4, location 33). Here you determine that if 2

successive alarms will occur during a specific period, the second alarm will be considered as a confirmed alarm (for confirmed alarm reporting, (see par. 4.5.3). Options: disable 30 min., 45 min., 60 min., or 90 min.

4.4.34 AC FAIL REP

(Fig. 4.4, location 34). Here you determine the time interval between AC power failure occurrence and the failure reporting. Options: 5 minutes, 30 minutes, 60 minutes or

180 minutes.

14 D-302017

Page 15

4.4.36 User Permission

(Fig. 4.4, location 36).

access to the INSTALLER MODE requires user permission. If you select ENABLE, the installer mode will be accessible only through the user menu after entering the user code. Options: Enable, Disable.

Note: This menu is not available when partition is enabled.

Here you determine whether the

4.4.39 Key Zones Options (Optional)

(Fig. 4.4, location 39). Here you determine whether or not the system can be armed and disarmed by zones 21-18, 29 or 21-29, provided that for these zones "non-alarm type" and "z-key enable" was predefined (see par. 4.3). Key zones can be wireless or wired zones. When using wireless key zones, only the MCT-100 and MCT-102 transmitters are used. The left pushbutton on the MCT-102 transmitter or input 1 of the MCT-100 transmitter is used for arming in AWAY mode. The right pushbutton on the MCT-102 transmitter or input 2 of the MCT-100 transmitter is used for disarming. When using wired key zones, the control panel toggles between AWAY mode and Disarm.

Note: In "Singapore" versions of the PowerMaxExpress, an open circuit arms the alarm system in AWAY mode and a closed circuit changes the state of the alarm system from AWAY mode to Disarm.

IMPORTANT! Enrolment of the MCT-100 or MCT-102 transmitter must be performed via the left pushbutton on the MCT-102 transmitter or input 1 of the MCT-100 transmitter.

Caution! Arming the system using a transmitter assigned to zones 21 and 28, or via wired zone 29 compromises security. This function is, therefore, only available in specific PowerMaxExpress versions according to the customer's request. Options: disable option, z. 21-28 enable, z. 29 enable, or z. 21-29 enable.

D-302017 15

Page 16

Refer to Figure 4.1a

to gain access to

USER SETTINGS

INSTALLER MODE

ENTER CODE

[installer code]

1. NEW INSTL CODE

2. ENROLLING

3. DEFINE ZONES

4. DEFINE PANEL

5. DEFINE COMM

01: ENTRY DELAY 1 02: ENTRY DELAY 2 03: EXIT DELAY 04: BELL TIME

entry dly1 00 s entry dly1 15 s entry dly1 30 s entry dly1 45 s entry dly1 60 s entry dly1 3 m entry dly1 4 m

05: ABORT TIME

abort time 00 s abort time 15 s abort time 30 s abort time 45 s abort time 60 s abort time 2 m abort time 3 m abort time 4 m

entry dly2 00 s entry dly2 15 s entry dly2 30 s entry dly2 45 s entry dly2 60 s entry dly2 3 m entry dly2 4 m

06: ALARM CANCEL 07: QUICK ARM

cancel time 1 m cancel time 5 m cancel time 15 m cancel time 60 m cancel time 4 h cancel inactive

USA

exit delay 30 s exit delay 60 s exit delay 90 s exit delay 120 s exit delay 3 m exit delay 4 m

quick arm ON quick arm OFF

bell time 1 m bell time 3 m bell time 4 m bell time 8 m bell time 10 m bell time 15 m bell time 20 m

08: BYPASS

manual bypass no bypass force arm

Note:

Force arm is not

applicable to the UK.

<OK> TO EXIT

Note:

The currently saved options are displayed with dark box at the right side of the display. To review the options, repeatedly click or until the desired option is displayed, then click OK (a dark box will be displayed at the right side).

Not applicable in the USA

09: EXIT MODE

restart exit off by door normal

13: SWINGER STOP

shut after 1 shut after 2 shut after 3 no shutdown

Note: Swinger Stop is defined for entire alarm system.

17: AUX BUTTON A

instant skip exit delay

21: NOT ACTIVE

no act time 3 h no act time 6 h no act time 12 h no act time 24 h no act time 48 h no act time 72 h no act disable

25: RESET OPTION

user reset enginner reset

29: DISARM OPTION

any time on entry wir eless entry + awake kp on entry al l

33: CONFIRM TIME

disable 30 minutes 45 minutes 60 minutes 90 minutes

USA

Figure 4.4 - DEFINE PANEL Flow Chart

10: PIEZO BEEPS 11: TRO UBL E BEEPS 12: PANIC ALARM

enable beeps off when home disable bee ps

14: CROSS ZONING 15: SUPERVISION

cross zone ON cross zone OFF

18: AUX B 2-W-KF

instant skip exit delay

26: TAMPER OPTION

zone tamper on zone tamper off

30: BELL/REP. OPT

EN standard other

34: AC FAIL REP

5 minutes 30 minutes 60 minutes 180 minutes

disable beeps enable beeps

off at night

USA

superv time 1 h superv time 2 h superv time 4 h superv time 8 h superv time 12 h disable

19: JAM DETECT

UL (20/20) EN (30/60) class 6 (30/60) disable

23: DURESS

duress code 2580

(Change the code or enter 0000 to disable duress function)

Note: Duress code is not applicable to the UK.

27: SIREN ON LINE

enable on fail disable on fail

31: LOW-BAT ACK

keyfob L-B on keyfob L-B off

36: USER PERMIT

disable enable

silent panic audible panic

disable panic

USA

16: NOT READY

normal in supervision

latchkey on latchkey off

24: PIEZO SIREN

piezo siren on piezo siren off

28:MEMORY PROMPT

enable disable

32: SCREEN SAVER

scrn saver OFF refresh by code refresh by key

39: KEY ZONES OPT

disable option z. 21-28 enable

z. 29 enable

z. 21-29 enable

20:LATCHKEY

16 D-302017

Page 17

4.5 DEFINING COMMUNICATION PARAMETERS

Preliminary Guidance

This mode allows you to adapt the telephone communication parameters to the local requirements.

Compatible central station receivers are: Osborne-Hoffman model 2000, Ademco Model 685, FBII Model CP220, Radionics Model D6500, Sur-Gard Model SG-MLR2-DG and Silent Knight Model 9500.

IMPORTANT: In telephone / pager number locations and account number locations, you may be required to enter hexadecimal digits. In telephone number locations, these digits are used as codes to control the dialer:

Hex. Digit

Keying Sequence

Code Significance

A <#> ⇒ <0> Applicable only at the beginning of a

number - the dialer waits 10 seconds or waits for dial tone, whichever comes first and then dials.

D <#> ⇒ <3> Applicable only at the beginning of a

number - the dialer waits 5 seconds for dial tone and goes on hook if none is received.

E <#> ⇒ <4> Applicable only in the middle of the

number - the dialer waits 5 seconds

F <#> ⇒ <5> Not applicable in phone numbers

Note: A "+" can be entered at the beginning of the line by

pressing

and then .

To enter a series of digits, use the following keys: <Numeric keypad> - to enter the number

- moves the cursor from left to right

- moves the cursor from right to left

- deletes everything after the cursor (to the right)

4.5.1 PSTN / GSM (Fig. 4.5 Detail A)

Area Code [Fig 4.5.1(1)] Here you enter the system tel. area code (up to 4 digits). Line Prefix [Fig 4.5.1(2)] Here you enter the number that is used as a prefix to access an outside telephone line (if exists). Dial Method [Fig 4.5.1(3)] Here you determine the dialing method used by the automatic dialer built into the PowerMaxExpress control panel. The options are: Pulse and tone (dtmf). GSM Keep Alive [Fig 4.5.1(4)] Here you prevent the GSM service provider from disconnecting the GSM line if the user has not initiated any outgoing telephone calls during the last 28 days. The options are: disable and every 28 days.

4.5.2 GPRS / BB [Fig. 4.5 Detail B]

The GSM/GPRS module is capable of communicating with the Central Station receiver by GPRS, GSM Voice and SMS channels. Each of the channels can be separately enabled or disabled in order to allow or prohibit the module from using it for the event reporting. If all channels are enabled, the GSM/GPRS module will always try GPRS first. If fails, it will try GSM Voice. If fails, it will try any other possible method (PSTN, Broadband) and only then it will try SMS. This is due to the fact that SMS is the most unreliable option of communication. Disabling any of the GSM Module channels will cause the module to use a different sequence than the one described above.

GPRS Report [Fig 4.5.2(1)] Here you determine whether the alarm system will report events to the central station via the GPRS channel. The options are: disable and enable.

GSM Report [Fig 4.5.2(2)] Here you determine whether the alarm system will report events to the central station via the GSM voice channel. The options are: disable and enable.

SMS Report [Fig 4.5.2(3)] Here you determine whether the alarm system will report events to the central station via the SMS channel. The options are: disable and enable.

GPRS APN [Fig 4.5.2(4)]

Here you enter the name of the APN (Access Point) used for the internet settings for the GPRS (up to 40 digits).

GPRS Username [Fig 4.5.2(5)] Here you enter the username of the APN used for GPRS communications (up to 30 digits).

GPRS Password [Fig 4.5.2(6)] Here you enter the password of the APN used for GPRS communications (up to 16 digits). The following table provides a list of the keys used by the PowerMaxExpress editor for the GPRS APN, GPRS Username, GPRS Password menus and Custom Zone Name option.

Key Functionality

Moves the cursor from left to right. Long press for speed. Moves the cursor from right to left. Long press for speed. Scrolls upward the sequence of inserted digits. Long press for speed. Scrolls downward the sequence of inserted digits. Long press for speed.

Places cursor to extreme right position of edit string and shows the last 16 digits of edit string.

Reverts to previous or top menu without saving the edit string.

Reverts to "<OK> TO EXIT" without saving the edit string.

Saves and reverts to previous menu.

Clears all digits to the right of cursor.

Clears one digit by cursor.

Selects between uppercase or lowercase digits.

PIN Code [Fig 4.5.2(8)] Enter PIN code of the SIM card installed in the PowerMaxExpress unit (up to 16 digits).

Force Home Network [Fig 4.5.2(9)] Here you determine whether to force the SIM card to use the home network only and not to select another network in case the home network cannot be found. The options are: disable and enable.

D-302017 17

Page 18

4.5.3 C.S. Reporting (Fig. 4.5 Detail C)

Report Events [Fig 4.5.3(1)] – see note in Fig. 4.5 Detail C

Here you determine which types of event will be reported to central stations. Due to lack of space in the display, abbreviations are used: alarm is “alrm”, alert is “alrt” and open/close is “o/c”. The asterisk (J) is a separator between events reported to central station 1 and events reported to central station 2. Messages are divided by type into four groups:

No. Group Events Reported

1 Alarms Fire, Burglary, Panic, Tamper 2 Open/close Arming AWAY, Arming HOME,

3 Alerts No-activity, Emergency, Latchkey,

4 Maintenance Low-battery AC failure

"Alarm" group has the highest priority and "Alert" group has the lowest priority. The selectable options are as follows:

Plan name Sent to center 1 Sent to center 2

all -o/c J backup All but open/close

all J all All All all-o/c J all -o/c All but open/close All but open/close all –o/c J o/c All but open/close Open/close all (–alrt) J alrt All but alerts Alerts Alrm J all (–alrm) Alarms All but alarms Disable report Nothing Nothing all J backup Al l All if cent. 1 doesn’t respond

Note: “All” means that all 4 groups are reported and also trouble messages - sensor / system low battery, sensor inactivity, power failure, jamming, communication failure etc

1st Report Method [Fig 4.5.3(2)] Here you define the 1st priority of method used to report events. The options are: disable, cellular and PSTN.

2nd Report Method [Fig 4.5.3(3)] Here you define the 2 events. If the method defined to report events in the 1st priority fails, the control panel will attempt to report using the method defined in the 2nd priority (see notes in 1 Report Method). The options are: disable, cellular and PSTN.

3rd Report Method [Fig 4.5.3(4)] Here you define the 3 events. If the method defined to report events in the 2 priority fails, the control panel will attempt to report using the method defined in the 3rd priority (see notes in 1 Report Method). The options are: disable, cellular and PSTN.

Dual Reporting [Fig 4.5.3(5)] Here you determine whether to report events using PSTN and cellular at the same time instead of waiting for the 1 method to fail before trying the 2 The options are: disable and PSTN & cellular.

Receiver 1 Account No. [Fig 4.5.3(6)] - see note in Fig. 4.5 Detail C Here you enter the number that will identify your specific alarm control system to the 1 consists of 6 hexadecimal digits.

Receiver 2 Account No. [Fig 4.5.3(7)] - see note in Fig.

4.5 Detail C Here you enter the number that will identify your system to

the 2

central station. The account number consists of 6

hexadecimal digits.

Disarming

Gas, Flood, Temperature

All but open/close if center 1 doesn’t respond

priority of method used to report

method.

central station. The number

PSTN/GSM RCVR1 [Fig 4.5.3(8)] - see note in Fig. 4.5 Detail C Here you program telephone number of the 1

central station (including area code, 16 digit max) to which the system will report the event groups defined in Report Events.

PSTN/GSM RCVR2 [Fig 4.5.3(9)] - see note in Fig. 4.5 Detail C Here you program telephone number of the 2

central station (including area code, 16 digit max) to which the system will report the event groups defined in Report Events.

IP RCVR 1 [Fig 4.5.3(10)] Here you enter the IP address of the IP receiver that is located in the 1

central station.

IP RCVR 2 [Fig 4.5.3(11)] Here you enter the IP address of the IP receiver that is located in the 2

central station.

SMS RCVR 1 [Fig 4.5.3(12)] Here you enter the telephone number of the SMS receiver that is located in the 1

central station.

SMS RCVR 2 [Fig 4.5.3(13)] Here you enter the telephone number of the SMS receiver that is located in the 2

central station.

PSTN Report Format [Fig 4.5.3(14)] - see note in Fig.

4.5 Detail C Here you select the reporting format used by the control panel to report events to central stations. The options are:  SIA text  Contact-ID  SIA  4/2 1900/1400  4/2 1800/2300  Scancom (see Appendix B

- code lists). 4/2 Pulse Rate [Fig 4.5.3(15)] - see note in Fig. 4.5 Detail

C Here you select the pulse rate at which data will be sent to

central stations if any one of the 4/2 formats has been selected in PSTN Report Format. The options are: 10, 20, 33 and 40 pps.

PSTN Report Retry [Fig 4.5.3(16)] - see note in Fig. 4.5 Detail C Here you determine the number of times the communicator will dial the central station’s number via PSTN. The options are: 2, 4, 8, 12 and 16 attempts.

GSM Report Retry [Fig 4.5.3(17)] - see note in Fig. 4.5

Detail C Here you determine the number of times the communicator will try to report via a cellular group (GPRS, GSM and SMS) to the central station. The options are: 2, 4, 8, 12 and 16 attempts.

Auto Test Time [Fig 4.5.3(18)]

Here you determine the time at which the telephone line will be tested and reported to the central station.

Auto Test Cycle [Fig 4.5.3(19)] Here you determine the time interval between consecutive telephone line test messages sent to the central station.

The control panel performs this at regular intervals to verify proper communications. The options are: test every 5 hours, test every 1, 2, 5, 7, 14, 30 days and test OFF.

Line Fail Report [Fig 4.5.3(20)]

[Fig 4.5.3(20a)]

PSTN

Here you determine if the PSTN telephone line disconnection will be reported or not and determine the delay between detection of line disconnection and the failure reporting. If the telephone line is disconnected, the message "tel line fail" will be stored in the event log.

The options are: don't report, immediately, 5 minutes, 30 minutes, 60 minutes or 180 minutes.

18 D-302017

Page 19

GSM/GPRS [Fig 4.5.3(20b)] Here you determine if the GSM/GPRS line disconnection will be reported or not and determine the delay between detection of line disconnection and report failure. If the telephone line is disconnected, the message "GSM line fail" will be stored in the event log. The options are: don't report, 2 minutes, 5 minutes, 15 minutes, or 30 minutes.

PSTN Up / Down [Fig 4.5.3(21)] Remote Access [Fig 4.5.3(21a)] Here you give or deny permission to access the system and exercise control from a remote telephone. The options are: rem. access ON and rem. access OFF.

Mast. Downl Code [Fig 4.5.3(21b)] Here you determine the master installer 4-digit password for downloading/uploading data into/from the PowerMaxExpress memory.

Attention! If "0000" is used, it will not enable connection of the PowerMaxExpress to the PC for upload/download purpose.

Inst. Downl Code [Fig 4.5.3(21c)] Here you determine the installer 4-digit password for downloading data into the PowerMaxExpress memory.

Attention! If "0000" is used, it will not enable connection of the PowerMaxExpress to the PC for upload/download purpose.

Upload Option [Fig 4.5.3(21d)] Here you determine whether the PowerMaxExpress data can be uploaded into a computer while the system is in disarm state or at any time (in HOME/AWAY arming & disarm state). The options are: when system OFF and any time

Up Download Tel# [Fig 4.5.3(21e)] Here you enter the telephone number (up to 16 digits) of the UL/DL server.

Note: Only for use with control panels monitored by compatible central stations. Leave empty if not used.

GPRS Up / Down [Fig 4.5.3(22)]

My SIM Tel. # [Fig 4.5.3(22a)] Here you enter the PowerMax SIM card telephone number. The central station dials this number when it needs to connect to the PowerMaxExpress for uploading / downloading data.

Caller ID# [Fig 4.5.3(22b)]

Here you determine the 1

VDNS receiver telephone number. When the PowerMaxExpress responds to an incoming call from the telephone number defined here, it creates a connection to the VDNS for uploading / downloading data.

Note: Caller ID#1 / ID#2 should be 6 or more digits for wake-up by VDNS to work.

Caller ID# [Fig 4.5.3(22c)]

Here you determine the 2

VDNS receiver telephone number. When the PowerMaxExpress responds to an incoming call from the telephone number defined here, it creates a connection to that VDNS for uploading / downloading data.

Report Cnfrm Alarm [Fig 4.5.3(24)] - see note in

Fig. 4.5 Detail C

Here you determine whether the system will report whenever 2 or more events (confirmed alarm) occur during a specific period (see par. 4.4.33). Available enable + bypass (enabling report and bypassing the detector - applicable to PowerMaxExpress that is compatible with DD243 standard).

options are: enable report, disable report,

Here you determine whether 24 hour (silent and audible) zones will function as normal 24 hour zones or as panic zones. The options are: both original, audible as panic, silent as panic, or both as panic.

Recent Close [Fig 4.5.3(26)] Here you enable or disable the “recent closing” report, that is sent to the central station if an alarm occurs within 2 minutes from the expiry of the exit delay. The options are: recent close ON and recent close OFF.

Zone restore [Fig 4.5.3(27)] Here you determine whether a zone restore will be reported or not. The options are: report restore and don't report.

System Inactivity Report [Fig 4.5.3(28)] Here you determine whether the central station will receive a message if the system is inactive (not armed) during a defined period (days). The options are: disable, rep. after 7d, rep. after 14d, rep. after 30d, rep. after 90d.

4.5.4 Private Report (Fig. 4.5 Detail D)

Report To Private [Fig 4.5.4(1)]

Here you determine which event groups will be reported to private telephone subscribers. The options are as follows:

• Alarms + alerts

• Alarms

• Alerts

• Disable report

The following siren signal will be sent to private telephone upon event reporting:

FIRE: ON - ON - ON - pause.... (- - - - - - ......).

BURGLAR: ON continuously ( EMERGENCY: 2-tone siren; like an ambulance.

Voice report [Fig 4.5.4(2)]

Private Tel# [Fig 4.5.4(2a)]

Here you program the 1

telephone number (including area code, if required) of the private subscriber to which the system will report the event groups defined in Report To Private.

Private Tel# [Fig 4.5.4(2b)]

Here you program the 2

telephone number (including area code, if required) of the private subscriber to which the system will report the event groups defined in Report To Private.

Private Tel# [Fig 4.5.4(2c)]

Here you program the 3

telephone number (including area code, if required) of the private subscriber to which the system will report the event groups defined in Report To Private.

Private Tel# [Fig 4.5.4(2d)]

Here you program the 4

telephone number (including area code, if required) of the private subscriber to which the system will report the event groups defined in Report To Private.

Redial Attempts [Fig 4.5.4(2e)] Here you determine the number of times the communicator will dial the called party’s number (private telephone).

The options are: 1, 2, 3 and 4 attempts.

Attention! A maximum of 2 dialing attempts is permitted by the Australian Telecommunication Authority.

Tel. acknowledge [Fig 4.5.4(2g)] Here you determine whether the system will use the single acknowledge or the all acknowledge mode when reporting to private telephones.

...)

Report 24H Zones [Fig 4.5.3(25)]

D-302017 19

Page 20

Note: In the single acknowledge mode, receiving an acknowledge signal from a single telephone is sufficient to consider the current event closed and call off the communication session. The remaining telephones serve for backup purposes only. In the all acknowledge mode, an acknowledge signal must be received from each telephone before the current event is considered reported.

The options are: single ack and all ack.

SMS Report Tel# [Fig 4.5.4(3)]

SMS Tel# [Fig 4.5.4(3a)]

Here you define the first SMS phone number (including area code, 16 digits maximum) to which pre-selected event types (see par. 4.6.3) will be reported.

SMS Tel# [Fig 4.5.4(3b)]

Refer to Figure 4.1a

to gain access to

USER SETTINGS

USER SETTING

INSTALLER MODE

ENTER CODE

[installer code]

1. NEW INSTL CODE

2. ENROLLING

3. DEFINE ZONES

4. DEFINE PANEL

5. DEFINE COMM.

Here you define the second SMS phone number (including area code, 16 digits maximum) to which pre-selected event types (see par. 4.6.3) will be reported.

SMS Tel# [Fig 4.5.4(3c)]

Here you define the third SMS phone number (including area code, 16 digits maximum) to which pre-selected event types (see par. 4.6.3) will be reported.

SMS Tel# [Fig 4.5.4(3d)]

Here you define the fourth SMS phone number (including area code, 16 digits maximum) to which pre-selected event types (see par. 4.6.3) will be reported.

1: PSTN / GSM

2: GPRS / BB

3: C.S. REPORTING

4: PRIVATE REPORT

see detail A

see detail B

see detail C

see detail D

Note

The currently saved options are displayed with dark box at the right side of the display. To review the options, repeatedly click or until the des ired optio n is displayed, then click OK (a dark box will be displayed at the right side).

Note

<OK> TO EXIT

Figure 4.5 – Defining Communications

FIGURE 4.5 - DETAIL A

1: PSTN / GSM

(Enter tel. area code)

4.5.1(1) Par. 4.5.1(2) Par. 4.5.1(3) Par. 4.5.1(4)

AREA CODE

xxxx

FIGURE 4.5 - DETAIL B

2: GPRS/BB

GPRS REPORT

disable enable

GPRS USERNAME

xxxx...

4.5.2(1) Par. 4.5.2(2) Par. 4.5.2(3) Par. 4.5.2(4)

Par. 4.5.2(5) Par. 4.5.2(6)

(up to 30 digits)

(Enter GPRS

username)

GSM REPORT SMS REPORT

disable enable

GPRS PASSWORD

xxxx...

LINE PREFIX

xxxx

(Enter prefix)

(up to 16 digits)

(Enter GPRS

password)

DIAL METHOD

tone (dtmf) pulse

disable enable

Par. 4.5.2(8)

SIM PIN CODE

(up to 16 digits)

xxxx...



(Enter SIM card

PIN code)

GSM KEEP ALIVE

disable every 28 days

GPRS APN

(up to 40 digits)

xxxx...

(Enter name of APN)

Par. 4.5.2(9)

FORCE HOME NETW.

disable enable

20 D-302017

Page 21

Note

For Control Pan el that has

installer code & master installer code, the following

functions are available only if the MASTER INSTALLER code is entered:

PSTN/GSM RCVR1 RCVR 1 ACCOUNT# RCVR 2 ACCOUNT# PSTN RPRT FORMAT 4/2 PLS RATE REPORT EVENTS GSM RPRT RETRY MAST. DL CODE

3:C.S. REPORTING

REPORT EVENTS

all - o/c * backup all all - o/c * all - o/c all - o/c * o/c all (-alrt) * alrt alrm * all (-alrm) disable report

all * backup

4.5.3(1) Par. 4.5.3(2) Par. 4.5.3(3) Par. 4.5.3(4)

all

FIGURE 4.5 - DETAIL C

1st RPRT METHOD

disable cellular PSTN

2nd RPRT METHOD 3rd RPRT METHOD

disable cellular PSTN

Note

Par. 4.5.3(5) Par. 4.5.3(6) Par. 4.5.3(7) Par. 4.5.3(8)

DUAL REPORTING

disable PSTN & cellular

Par. 4.5.3(9) Par. 4.5.3(10) Par. 4.5.3(11) Par. 4.5.3(12)

PSTN/GSM RCVR2

(Enter Tel. No.)

Par. 4.5.3(13) Par. 4.5.3(14)

SMS RCVR 2

(Enter Tel. No.)

Par. 4.5.3(17) Par. 4.5.3(18)

GSM RPRT RETRY

2 attempts 4 attempts

8 attempts 12 attempts 16 attempts

RCVR 1 ACCOUNT#

1st acc. no.

(Enter RCVR 1

account No.)

IP RCVR 1

000.000.000.000

(Enter IP address) (Enter IP address)

PSTN RPRT FORMAT PSTN RPRT RETRY

SIA 4/2 1900/1400 4/2 1800/2300 Scancom SIA text contact ID

AUTO TEST TIME

test time 12:00P

(Enter time)

RCVR 2 ACCOUNT# PSTN/GSM RCVR1

2nd acc. no. (Enter RCVR 2

account No.)

IP RCVR 2

000.000.000.000

Par. 4.5.3(15) Par. 4.5.3(16)

(Enter Tel. No.)

SMS RCVR 1

(Enter Tel. No.)

4/2 PULSE RATE

20 pps 33 pps 40 pps 10 pps

Par. 4.5.3(19)

2 attempts 4 attempts

8 attempts 12 attempts 16 attempts

AUTO TEST CYCLE

test OFF test every 1 d test every 2 d test every 5d test every 7 d test every 14 d test every 30 d test every 5 h

Continues in

next Figure

D-302017 21

Page 22

REPORT EVENTS

(see DETAIL C

in previous drawing)

Par. 4.5.3(20)

LINE FAIL REPORT

4.5.3(20a)

PSTN

FIGURE 4.5 - DETAIL C continued

Par. 4.5.3(21)

PSTN UP / DOWN

Par. 4.5.3(20b)

GSM/GPRS

Remote access

4.5.3(21a)

Par. 4.5.3(21b)

Mast. downl code

immediately 5 minutes

30 minutes 60 minutes 180 minutes don’t report

Par. 4.5.3(21c)

Inst. downl code

downl. code BBBB

(Enter )

Par. 4.5.3(22)

GPRS UP/DOWN

4.5.3.(22a)

My SIM TEL. #

(Enter SIM card

Tel. No.)

Par. 4.5.3(24)

RPRT CNFRM ALARM

disable report enable + bypass

enable report

2 minutes 5 minutes 15 minutes 30 minutes

don’t report

Par. 4.5.3(21d)

Upload option

any time when system OFF

4.5.3.(22b) 4.5.3.(22c)

1st Caller ID#

(Enter 1st IP receiver

Tel. No .)

Par. 4.5.3(25)

REPORT 24H ZONES

both original audibl as panic silent as panic

both as panic

rem. access ON rem. access OFF

(Enter 2nd IP receiver

recent cl. OFF recent cl. ON

Par. 4.5.3(21e)

Up download tel#

(Enter Tel. No.)

2nd Caller ID#

Tel. No.)

Par. 4.5.3(26)

RECENT CLOSE

downl. code

xxxx

(Enter 4-digit code “0000” is not valid)

Par. 4.5.3(27)

ZONE RESTORE

report restore don’t report

AAAA

Par. 4.5.3(28)

SYS INACT REPORT

disable rep. after 7d rep. after 14d rep. after 30d rep. after 90d

22 D-302017

Page 23

Note

FIGURE 4.5 - DETAIL D

4: PRIVATE REPORT

REPORT TO PRVT

disable report alarms+alerts

alarms alerts

1st private tel#

 



4th private tel#

 



4.5.4(1)

Par. 4.5.4(2a)

Tel . No.

Par. 4.5.4(2d) Par. 4.5.4(2e)

Tel . No.

Par. 4.5.4(2) Par. 4.5.4(3)

VOICE REPORT SMS REPORT TEL#

Par. 4.5.4(2b) Par. 4.5.4(2c)

2nd private tel#



Tel . N o.

 

Redial attempts

1 attempt 2 attempts 3 attempts 4 attempts

Par. 4.5.4(3a) Par. 4.5.4(3b)

1st SMS tel#



SMS Tel. No.

 

3rd private tel#



Tel . N o .

 

Par. 4.5.4(2g)

Tel. acknowledge

single ack all ack

2nd SMS tel#



SMS Tel. No.

 

Par. 4.5.4(3c)

3rd SMS tel#



SMS Tel. No.

 

4.6 GSM Auto Detection

The GSM/BBA modem auto detection feature enables automatic enrollment of the GSM modem into the PowerMaxExpress control panel memory. GSM modem auto detection is activated in one of two ways: after tamper restore and after reset (power-up or after exiting the installer menu). This causes the PowerMaxExpress to automatically scan GSM COM ports for the presence of the GSM modem.

4.7 BBA Auto Detection

The BBA modem auto detection feature enables automatic enrollment of the BBA modem into the PowerMaxExpress control panel memory. BBA modem auto detection is activated in one of two ways: after tamper restore and after reset (power-up or after exiting the installer menu). This causes the PowerMaxExpress to automatically scan BBA COM ports for the presence of the BBA modem.

Par. 4.5.4(3d)

4th SMS tel#



SMS Tel. No.

 

In the event that the GSM modem auto detection fails and the modem was previously enrolled in the PowerMaxExpress control panel, the message "Cel Rmvd Cnfrm" will be displayed. This message will disappear from the display only

OKI

after the user clicks

. The modem is then considered as not enrolled and no GSM trouble message will be displayed.

Note: A message is displayed only when the PowerMaxExpress alarm system is disarmed.

In the event that the BBA modem auto detection fails and the modem was previously enrolled in the PowerMaxExpress control panel, the message "BBA Remvd Cnfrm" will be displayed. This message will

disappear from the display only after the user clicks The modem is then considered as not enrolled and no BBA trouble message will be displayed.

Note: A message is displayed only when the PowerMaxExpress alarm system is disarmed.

OKI

D-302017 23

Page 24

4.9 DEFINE CUSTOM

This mode allows you to define up to 5 zones names (in addition to the zone names that can be defined in the DEFINE ZONES mode - see par. 4.3).

(see figure 4.1a)

9. DEFINE CUSTOM

OKI

CUST. ZONES NAME

<OK> TO EXIT

OKI

EDIT USER TERM 1 EDIT USER TERM 2 EDIT USER TERM 3 EDIT USER TERM 4 EDIT USER TERM 5

To edit User Terms, use the following buttons on the control panel keypad:

press to scroll backward; press to scroll forward ;

press to change from small caps to big caps ; press for space

Figure 4.9 – Define Custom

4.10 DIAGNOSTIC TEST

This mode allows you to test the function of all protected area wireless sensors / wireless sirens / wireless keypads and to receive / review information regarding the received signal strength. Three reception levels are sensed and reported: Received Signal Strength Indication:

Reception Buzzer Response Strong Happy Tune twice ( - - - –––– ) ( - - - ––––) Good Happy Tune ( - - - –––– ) Poor Sad tune ( –––––––– )

The diagnostic test process is shown in figure 4.10. The following GSM/ GPRS messages are reported:

Message Description Unit is OK GSM / GPRS functioning properly. GSM comm.

loss

The GSM/GPRS module does not communicate with the Panel

Pin code fail Missing or wrong PIN code.

(Only if SIM card PIN code is enabled.)

GSM net. fail Unit failed with registration to local

GSM network.

SIM card fail SIM not installed or SIM card failure. GSM not detected No GPRS service GPRS conn. fail

GSM auto enroll failed to detect GSM/GPRS module. The SIM card does not have the GPRS service enabled. Local GPRS network is not available or, wrong setting to GPRS APN, user and/or password.

Srvr unavailable

VDNS Receiver cannot be reached – Check the Server IP

IP not defined Server IP #1 and #2 are not configured. APN not

APN is not configured.

defined SIM card locked

After entering a wrong PIN code 3 consecutive times the SIM is locked. To unlock it enter a PUK number. The PUK number cannot be entered by the PowerMax Pro.

Denied by server

The VDNS denies the connection request. Check that the Panel is registered on the VDNS Receiver.

When you are instructed to perform "walk test", walk throughout the site to check the detectors / sensors. When a detector/sensor is triggered into alarm, its name, number and the alarm reception level should be indicated (for example, "Bathroom", "Z19 strong") and the buzzer should sound according to the alarm reception level (1 of 3).

IMPORTANT! Reliable reception must be assured. Therefore, a "poor" signal strength is not acceptable. If you get a

"poor" signal from a certain detector, re-locate it and re-test until a "good" or "strong" signal strength is received. This principle should be followed during the initial testing and also throughout subsequent system maintenance.

24 D-302017

Page 25

(see figure 4.1a)

10. DIAGNOSTICS

NON-PARTITIONING ONLY

WL SENSORS TEST

DIAG. TESTING

(Perform walk test)

BATHROOM

Z19 STRONG

DIAG. TESTING

FRONT DOOR

(alternating for 5 sec.)

Z1 POOR

LIVING ROOM

(alternating for 5 sec.)

Z2 OK

(Each time the OK button is presse d,

the next test result is displayed)

Example

of test

result

display

Example

WL SIRENS TEST

S1 CPU =STRONG

of test result

S2 CPU =STRONG

display

Note STRONG/GOOD/POOR/ “NOT OK” (with siren No., S1 or S2 before) is

of test

displayed according to the

result

wireless siren signal

display

strength). S1=siren 1. S2 = siren 2. CPU = Control Panel Unit = 2 way comm.

S1 CPU

WAIT

S2 C PU

PLEASE WAIT...

WL KEYPADS TEST

K1 CPU

WAIT

K1 CPU= STRONG

K2 CPU

PLEASE WAIT...

K2 CPU=STRONG

Note STRONG/GOOD/POOR/ “NOT OK” (with keypad No., K1 or K2 before) is

displayed according to the wireless siren signal strength).

K1=keypad1 K2=keypad2

CPU = Control Panel Unit = 2 way comm.

Figure 4.10 - Diagnostic Test Flow Chart

4.11 USER FUNCTIONS

This mode provides you with a gateway to the user functions through the regular user programming menu. You may:

• Program the 4 (private) telephone numbers

• Program user codes

• Enroll keyfobs

• Set the auto arm option

• Set arming time

• Set the squawk option

• Set the system time and time format

• Set the date and date format

Refer to the User Guide for detailed procedures.

Caution! If after having programmed the user codes the system does not recognize your installer code, this indicates you must have programmed a user code that is identical with your installer code. If so, access the user menu and change the code that is identical with your installer code. This will re-validate your installer code.

4.12 RETRIEVING FACTORY DEFAULTS

If you want to reset the PowerMaxExpress parameters to the factory default parameters, you should enter the installer menu and perform the "FACTORY DEFLT" function, as described in the right side illustration. To get the relevant parameters defaults, contact the PowerMaxExpress dealer.

Note: For PowerMaxExpress with 2 installer codes, INSTALLER code and MASTER INSTALLER code, only the master installer code enables to perform factory default function.

Entering to/exit from the FACTORY DEFLT menu is shown in figure 4.1a

This is a brief display after which all the factory defaults are retrieved.

4.13 SERIAL NUMBER

The menu "13. SERIAL NUMBER" enables reading the system serial number and panel ID for support purposes only.

4.14 CALLING UPLOAD/DOWNLOAD SERVER

Note:

This option is only used during the installation of panels monitored by compatible central stations.

Panel ID is a unique number of the control panel that is used for registering the PowerMaxExpress to VDNS when using GPRS.

This option allows the installer to initiate a call to the upload/download server. The server uploads the PowerMaxExpress configuration to its data base and can unload predefined parameters to the PowerMaxExpress .

GPRS CONN. TEST LAN CONNECT. TEST

( )

When the OK button is pressed, the test result takes

between 15 sec. to 4 mins. before it is displayed, depending on the severity of the failure. See par. 4.10 for a complete list of possible GSM/GPRS messages.

( )

PLEASE WAIT... PLEASE WAIT...

UNIT IS OK UNIT IS OK

12. FACTORY DEFLT

<OK> to restore

ENTER CODE:

PLEASE WAIT ...

( )

[installer code]

D-302017 25

Page 26

Refer to Figure 4.1a

to gain access to

USER SETTINGS

INSTALLER MODE

ENTER CODE

[installer code]

1. NEW INSTL CODE

2. ENROLLING

3. DEFINE ZONES

4. DEFINE PANEL

5. DEFINE COMM

Displayed during

dialing process

Displayed during

download process

If UL/DL server tel. # is already

defined (see

par. 4.5.34)

COMMUNICATING TEL # NOT DEFINED

Dialing

DOWNLOADING DIAL ATTEMPT FAIL

If UL/DL server

tel. # was not

defined before

(see par. 4.5.34)

Dialing

failed

Displayed for half

a minute approx.

accompanied by sad

(failure) melody

Displayed for half

a minute approx.

accompanied by sad

(failure) melody

9. DEFINE CUSTOM

10. DIAGNOSTIC S

11. USER SETTINGS

12. FACTORY DEFLT

13. SERIAL NUMBER

14. START UL/DL

<OK> TO EXIT

Displayed for half

a minute approx.

accompanied by happy

(success) melody

Download

DOWNLOAD OK DOWNLOAD FAILED

Non-Partition

mode

READY 00:00

Figure 4.14 – Start UL/DL

Partition

mode

P1 RDY 00:00

Download

failed

Displayed for half

a minute approx.

accompanied by sad

(failure) melody

4.15 ENABLING/DISABLING PARTITIONS

This mode allows you to enable/disable the partitioning feature (optional).

Partitioning allows you to divide the system into a maximum of four independently controllable areas. A different user code is assigned to each partition

. A partition can also be armed or disarmed regardless

area

in order to limit or control access to each

of the status of the other partitions within the system. When the partition feature is disabled, zones, user codes

and features will operate the same as in a regular PowerMaxExpress unit. When partition is enabled, menu displays are changed to incorporate the partition feature.

Refer to Figure 4.1a

to gain access to

USER SETTINGS

INSTALLER MODE

ENTER CODE

[inst. code]

1. NEW INSTL CODE

15. PARTITIONING

<OK> TO EXIT

Note:

Partitioning is an optional feature

Figure 4.15 – Partitioning

enable disable

4.16 WALK-TEST

This mode (see Figure 4.1a) provides you with the means to conduct a periodic test, via the walk-test menu, at least once a week and after an alarm event.

26 D-302017

Page 27

5. TESTING PROCEDURES

5.1 Preparations

Make sure all windows and doors are closed. If all zones are secured (undisturbed), the display should read:

READY HH:MM

If the display is “NOT READY”, query the control panel by

OKI

pressing the

button repeatedly. The source(s) of the problem(s) will be displayed and read aloud. Take the necessary measures to eliminate the problem(s) before testing the system (see next paragraph).

5.2 Diagnostic Test

To verify proper function of all detectors in the system, a comprehensive diagnostic test is required. To perform this test, refer to figure 4.10.

5.3 Keyfob Transmitter Test

Initiate transmission from each transmitter enrolled as a keyfob unit (according to the list in Table A2, Appendix A). Use each transmitter to arm the control panel AWAY and immediately disarm it. Upon pressing the keyfob unit’s AWAY key, the ARM indicator should light. The display should respond as follows:

ARMING AWAY

PLEASE EXIT NOW

The exit delay beeps will begin. Press the keyfob unit’s DISARM (

should extinguish, the announcement “Disarm, ready to arm" should be heard and the display should revert to:

READY HH:MM

Test the AUX button in each keyfob in accordance with the



) key. The ARM indicator

6. MAINTENANCE

6.1 Dismounting the Control Panel

A. Remove the screw that fastens the front unit to the back

unit (see figure 3.1H).

B. Remove the 3 screws that fasten the back unit to the

mounting surface (see figure 3.1A) and remove the control panel.

6.2 Replacing the Backup Battery

Replacement and first-time insertion of battery pack is similar (see figure 3.1C).

With fresh battery pack, correct insertion and tightened battery compartment lid, the TROUBLE indicator should extinguish. However, the “MEMORY” message will now blink in the display (caused by the “tamper” alarm you triggered when opening the battery compartment lid). Clear it by arming the system and immediately disarming.

information noted in Table A.2, Appendix A. Verify that the AUX button performs its duty as programmed.  If the AUX (

@) button is defined as “INSTANT”, press

the AWAY button and then the AUX button. The response should be:

ARMING INSTANT

(alternating)

PLEASE EXIT NOW

and the exit delay beeps will start. Press the DISARM (

) key immediately to disarm.

 If the

AUX (*) button is defined as "skip exit delay", press the AWAY button and while you hear the exit beeps press the AUX button – the exit beeps will be stopped immediately and the system will be armed AWAY. Press the DISARM key disarm the system.

( ) immediately to

5.4 Emergency Transmitter Test

Initiate transmission from each transmitter enrolled to an emergency zone (according to the list in Table A3, Appendix A). For example, upon pressing the transmit button of an emergency transmitter enrolled to zone 22, the display should read:

Z22 EMERGENCY

(alternating)

VIOLATED

It is advisable to let the central station know that you are conducting this test, or just disconnect the telephone line from the PowerMaxExpress during the test, to prevent false alarms.

6.3 Fuse Replacement

The PowerMaxExpress has an internal fuse that has automatic reset. Therefore, there is no need to replace fuse. When over current condition occurs, the fuse cuts off the circuit current. Upon fault current being removed for several seconds, the fuse is automatically reset and allows current flow through the circuit again.

6.4 Replacing/Relocating Detectors

Whenever maintenance work involves replacement or relocation of detectors, always perform a full diagnostic test

according to par. 4.10. Remember! A "poor" signal is not acceptable, as stated at

the end of the test procedure.

7. READING THE EVENT LOG

Events are stored in the event log. You can access this log and review the events, one by one. If the event log fills up completely, the oldest event is deleted upon registration of each new event.

date and time of occurrence are memorized for each

The event.

D-302017 27

When reading the event log, events are shown in chronological order - from the newest to the oldest. Access to the event log is provided by clicking the

key and not through the installer’s menu. Reading and erasing process of the event log is shown in the next drawing.

Page 28

CODE _ _ _ _

(Enter 4-digit

installer code)

LIST OF EVENTS

Latest Event

Oldest Event

CLEAR EVENT LOG

<OFF> TO DELETE

(*)

(**)

<OK TO EXIT

(Return to normal

operation)

Figure 7 - Reading / Erasing the Event Log

* While the system is in normal operation mode, click

to review the event log.

** Event is displayed in 2 parts, for example, "Z13 alarm" then "09/02/00 3:37 P". The two displays will be shown

alternately until clicking

OKI

again to move to the next event or until the end of the event log (4 minutes).

*** Applicable only if installer code is entered.

28 D-302017

Page 29

APPENDIX A. Detector Deployment & Transmitter Assignments

A1. Detector Deployment Plan

Zone

No.

1 2 3 4 5 6 7 8

9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28

29 (*) 30 (*)

Zone Types: 1 = Interior follower < 2 = Perimeter < 3 = Perimeter follower < 4 = Delay 1 < 5 = Delay 2 < 6 = 24 h silent

14 = Temperature < 15 = Home / delay.

Zone Locations: Note down the intended location for each detector. When programming, you may select one of 26 available zone names (plus 5 custom zone names that you can add - see Figure 4.3 - Define Zones).

* Zones 29 only is hardwired zones.

A2. Keyfob Transmitter List

No. Type Holder Skip exit delay or Arming

1 2 3 4 5 6

Zone Type Sensor Location or Transmitter Assignment

7 = 24 h audible < 8 = Fire < 9 = Non-alarm < 10 = Emergency < 11 = Gas < 12 = Flood < 13 = Interior

Transmitter Data AUX button Assignments

(in non-alarm or emergency zones)

Indicate the desired function

“instant”

(if any) – see par. 4.4.17 (Aux button).

Skip exit delay

Arming “instant”

F F

Chime

(Yes / No)

D-302017 29

Page 30

A3. Emergency Transmitter List

Tx # Transmitter Type Enrolled to Zone Name of holder

A4. Non-Alarm Transmitter List

Tx # Transmitter Type Enrolled to Zone Name of holder Assignment

30 D-302017

Page 31

APPENDIX B. Event Codes

Contact ID Event Codes

Code Definition Code Definition

101 Emergency 351 Telco fault 110 Fire 373 Fire detector trouble 120 Panic 381 Loss of supervision

121 Duress 383 Sensor tamper 122 Silent 384 RF low battery 123 Audible 393 Fire detector clean me 131 Perimeter 401 O/C by user 132 Interior 403 Auto arm 134 Entry/Exit 406 Cancel 137 Tamper/CP 408 Quick arm 139 Burglary verified 426 Door open event 151 Gas alarm 441 Armed home 154 Flood alarm 454 Fail to close 180 Gas trouble 455 Fail to arm 301 AC loss 456 Partial arm 302 Low system battery 459 Recent close event 311 Battery disconnect 570 Bypass 313 Engineer reset 602 Periodic test report 321 Bell 607 Walk test mode 344 RF receiver jam detect 641 Senior watch trouble 350 Communication trouble

Code Definition Code Definition

AR AC Restore GJ Gas trouble restore AT AC Trouble HA Holdup Alarm (duress) BA Burglary Alarm LR Phone Line Restore BB Burglary Bypass LT Phone Line Trouble BC Burglary Cancel OP Opening Report BR Burglary Restore OT Fail to Arm BT Burglary Trouble /

Jamming

BV Burglary Verified QA Emergency Alarm BZ Missing Supervision RN Engineer Reset CF Forced Closing RP Automatic Test CI Fail to Close RX Manual Test CL Closing Report RY Exit from Manual Test CP Auto Arm TA Tamper Alarm CR Recent Close TR Tamper Restore EA Door Open WA Flood alarm FA Fire Alarm WR Flood alarm restore FT Fire Detector Clean XR Sensor Battery Restore FJ Fire detector trouble XT Sensor Battery Trouble FR Fire Restore YR System Battery Restore GA Gas alarm YT System Battery Trouble /

GR Gas alarm restore YX Service Required GT Gas trouble

4/2 Event Codes

Note: The report to central station is on the following zones: First wireless siren - zone 31, second wireless siren - zone 32, GSM - zone 33, first 2-way keypad (MKP-150/MKP-151) - zone 35, second 2-way keypad (MKP-150/MKP-151) - zone 36.

Alarms

Zone # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29

1st digit

2nd digit

Restorals

Zone # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29

1st digit

2nd digit

Supervisory trouble

Zone # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28

1st digit

2nd digit

Low Battery

Zone # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28

1st digit

2nd digit

Forced Arming – 8 users

User No. 1 2 3 4 5 6 7 8

1st digit A A A A A A A A 2nd digit 1 2 3 4 5 6 7 8

Zone Bypass

Zone # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29

1st digit

2nd digit

4 4 4 4 444 4 4 4 4 4444555555555 5 5 5 5 5 1 2 3 4 567 8 9 A B CDEF123456789 A B C D E

C C C C CCC C C C C CCCCDDDDDDDDD D D D D D 1 2 3 4 567 8 9 A B CDEF123456789 A B C D E

6 6 6 6 666 6 6 6 6 6666777777777 7 7 7 7 1 2 3 4 567 8 9 A B CDEF123456789 A B C D

8 8 8 8 888 8 8 8 8 8888999999999 9 9 9 9 1 2 3 4 567 8 9 A B CDEF123456789 A B C D

A A A A AAA A A A A AAAABBBBBBBBB B B B B B 1 2 3 4 567 8 9 A B CDEF123456789 A B C D E

SIA Event Codes

PA Panic Alarm

Disconnection

D-302017 31

Page 32

Panic / 24 Hours - 8 users

User No. 1 2 3 4 5 6 7 8 Panic CP Duress

1st digit 2 2 2 2 2 2 2 2 2

2nd digit 1 2 3 4 5 6 7 8 9 A

Arm HOME and AWAY (Closing)

User No. 1 2 3 4 5 6 7 8 Cancel alarm Recent Close

1st digit E E E E E E E E E E 2nd digit 1 2 3 4 5 6 7 8 9 C

Disarm (Opening)

User No. 1 2 3 4 5 6 7 8

1st digit F F F F F F F F 2nd digit 1 2 3 4 5 6 7 8

Trouble

Event Fuse

1st digit 2 2 2 2 1 1 1 1 1 2nd digit C D E F 1 2 3 4 6

Event CP Tamper

1st digit 1 1 1 1 1 1 2nd digit 7 8 A D E F

Fail

Restore

Fuse

Restore

Jamming Jamming

Restore

No Active COMM. &

LINE Restore

Failure

Restore

CPU Low

Battery

CPU Low

Battery Restore

Enter Test Exit Test Auto Test

Tamper

Understanding the Scancom Reporting Protocol Data Format

The SCANCOM data format consists of 13 decimal digits divided into 4 groups, from left to right, as shown at the right side. Each channel is associated with a specific event as follows:

"C": Fire 5th "C": Alarm cancel

"C": Personal attack 6th "C": Emergency

"C": Intruder 7th "C": Second alarm

"C": Open/close 8th "C": Trouble messages

Account

Code

Channels

1 - 4

aaaa cccc cccc s

The digit in this position conveys

the status of channel 1

Scancom Data Format

Channels

5 - 8

The digit in this position conveys

the status of channel 8

System Status:

no trouble,

test, low battery

32 D-302017

Page 33

APPENDIX C. Programmable Zone Types

C1. Delay Zones

A delay zone has exit and entry delays set by you in the course of programming the system. Warning beeps will sound throughout these delays, unless you choose to mute them.

• Exit Delay - The exit delay begins once the user arms the system. It allows him to leave via interior zones and a doorway before arming actually takes effect. When the exit delay starts, the buzzer beeps slowly and maintains a slow beeping rate until the last 10 seconds, during which it beeps rapidly. The PowerMaxExpress has two types of delay zones, for which different delay times may be set.

• Entry Delay - The entry delay begins once the user enters the protected area via a specific doorway (his entry is sensed by a delay zone detector). To avoid an alarm, he must reach the keypad via interior zones (which become "follower zones" during the entry delay) and disarm the system before the delay expires. When the entry delay starts, the buzzer beeps slowly until the last 10 seconds, during which it beeps rapidly.

C2. Emergency Zones

You can provide incapacitated, sick or elderly people with a miniature single-button transmitter to be carried on the neck like a pendant or to be worn on the wrist like a watch. In distress situations, they can press the button on their transmitter, causing the PowerMaxExpress to send an emergency call to the central monitoring station or to private telephones designated by the installer.

To make this possible, define the required number of zones as emergency zones and enroll a portable transmitter to each one of these zones. When completed, ask the master user to distribute these transmitters to their potential users.

C3. Fire Zones

A fire zone uses smoke detectors and is permanently active (a fire alarm is triggered regardless of whether the system is armed or disarmed). Upon detection of smoke, a pulsating siren sounds immediately and the event is reported via the telephone line.

C4. Flood Zone

A flood zone is permanently active (a flood alarm is triggered regardless of whether the system is armed or disarmed). Upon detection of flood leak, the event is reported via the telephone line.

C5. Gas Zone

A gas zone is permanently active (a gas alarm is triggered regardless of whether the system is armed or disarmed). Upon detection of gas leak, the event is reported via the telephone line

C6. Interior Zone

Interior zones are zones within the protected premises that have nothing to do with perimeter protection. Their most important feature is that they allow free movement within the protected area without initiating an alarm, provided that the system is armed in the "HOME" mode. People can therefore stay at home and move about freely, as long as they do not disturb a PERIMETER zone. Once the system is armed in the AWAY mode (all zones are protected), interior zones will initiate an alarm if violated.

C7. Interior Follower Zones

"Interior Follower" zone is a zone that is located between entry/exit zone and the alarm system control panel. This zone is temporarily delay periods, to enable you to walk (without causing an alarm) in front of a motion detector that is associated with the Interior Follower zone, after you enter through an entry zone on the way to the control panel, or when leaving the protected premises after system arming.

ignored by the alarm system during entry/exit

C8. Non-Alarm Zones

A non-alarm zone does not directly participate in the alarm system. It can be used for chime or for optional KEY ONOFF feature (when enabled). You can define the desired number of non-alarm zones and enroll a portable transmitter or a wireless device (detector) to this type of zone.

C9. Perimeter Zones

Perimeter zones rely on detectors designed to protect doors, windows and walls. An immediate alarm is initiated when such a zone is violated by opening the door/window or by trying to break the wall.

C10. Perimeter Follower Zones

A non-entry/exit zone, typically a perimeter zone located on an entry/exit path, that is treated as an entry/exit zone during an entry/exit time.

C11. 24-Hour Zones

24 hour zones are mainly used for PANIC buttons, perimeter detectors and anti-tamper protection. They therefore trigger an alarm in both armed and disarmed states.

• 24 Hour Zone - Silent. - Upon detection, this zone initiates a silent alarm, meaning that the sirens do not function. Instead the PowerMaxExpress dials telephone numbers and reports the event to central stations and/or to private telephones, as programmed.

• 24 Hour Zone - Audible. - Upon detection, this zone initiates a siren alarm. The PowerMaxExpress also dials telephone numbers and reports the event to central stations and/or to private telephones, as programmed.

D-302017 33

Page 34

APPENDIX D. PowerMaxExpress Compatible Devices

D1. PowerMaxExpress Compatible

Detectors

Each detector compatible with the PowerMaxExpress system is packed with its own installation instructions. Read them carefully and install as indicated.

A. PIR Motion Detectors

The wireless passive infrared (PIR) motion detectors used in the system are of the PowerCode type. The PowerMaxExpress is capable of “learning” each detector’s identification code and linking it to a specific zone (see par.

4.3 in this Guide). Some units are shown below:

K9-85 MCW

Note: K-940 MCW, Discovery K9-80/MCW and NEXT

K9-85 MCW are pet immune units.

In addition to its unique 24-bit identification code, each detector transmits a message, containing status information:

• The detector is in alarm (or not).

• The detector is being tampered with (or not).

• The battery voltage is low (or normal).

• “This is a supervisory message”.

If any of these detectors detects motion, it sends out a message to the alarm control panel. If the system is in the armed state, an alarm will be triggered.

B. Magnetic Contact Transmitter

MCT-302 is a PowerCode magneticcontact transmitter used to detect the opening of a door or a window. contacts are closed as window remains

The unit has an extra alarm input that acts as if it were a separate wireless transmitter. It sends (or does not send) a “restored to normal“ message to the alarm system, depending on the setting of an on-board “DIP” switch. The “restore” message informs you, through the control panel’s display, whether the door or window is open or closed.

C. MCT-100 Wireless Adapter for Wired Detectors MCT-100 is a PowerCode device used mainly as a wireless adapter for 2 regular magnetic switches installed on 2 windows in the same room. It has two inputs, behaving as separate wireless transmitters with different PowerCode IDs. Each input sends (or does not send) a “restored“ message to the alarm system, depending on the setting of an on-board “DIP” switch.

D. Wireless Smoke Detector MCT-425. A photoelectric smoke

detector equipped with a PowerCode-type transmitter. If enrolled to a fire zone, it initiates a fire alarm upon detection of smoke.

E. Glass Break Detector MCT501 An acoustic detector equipped

with a PowerCode-type transmitter. Since it restores automatically after detection, this unit does not send a restoral message to the control panel.

34 D-302017

closed.

MCPIR-3000

or K-940 MCW

long as the door or

The alarm

DISCOVERY

K9-80/MCW

MCT-302

MCT-100

MCT-425

MCT-501

D2. PowerMaxExpress Compatible Transmitters

The PowerMaxExpress system is compatible with multibutton and single button key-ring and hand-held transmitters that use PowerCode and CodeSecure coding methods. Multi-button PowerCode transmitters transmit the same code each time the same button is pressed. They can be used for emergency signaling. They can not be used for

arming / disarming.

CodeSecure transmitters are of the rolling code type - they transmit a new code each time the same button is pressed. This provides a higher security level, especially in arming / disarming applications, because the code can not be copied (“grabbed”) by unauthorized people. Following are the basic details of several compatible transmitters. The possible applications for each pushbutton are indicated in each drawing.

A. MCT-234

‘Keyfob’ transmitter. You can program the AUX (auxiliary) button to perform various tasks, in accordance with the user’s needs. Pressing AWAY and HOME together for 2 sec. initiates PANIC alarm. Pressing AWAY for 2 sec. initiates Latchkey arming.

AWAY

HOME

MCT-234

B. MCT-231 / 201*

(N.A. in North America) Single-button pendant units. The MCT-231 (Code- Secure) and the MCT-201 (PowerCode) can be enrolled to perform functions as shown. Both units look alike.

MCT-231 / 201

C. MCT-134 / 104*

(N.A. in North America) 4-button hand-held units. MCT-134 (CodeSecure) can replace the MCT-234 keyfob. MCT-104 (PowerCode) can perform emergency and nonalarm functions. Both units look alike.

MCT-134 / 104

D. MCT-132 / 102*

(N.A. in North America) 2button units. MCT-132 (CodeSecure) can perform functions as shown. (PowerCode) can perform emergency and non-alarm tasks. Both units look alike.

MCT-102

MCT-132 / 102

DISARM

AUX

Page 35

E. MCT-131 / 101*

(N.A. in North America) Single-button units. The MCT-131 (CodeSecure) and the MCT-101 (PowerCode) can be enrolled to perform functions as shown. Both units look alike.

MCT-131 / 101

F. MCT-211*

Water-proof, Power-Code transmitter. Can be enrolled to perform emergency or non-alarm functions.

* Not UL listed.

wrist-worn

MCT-211

D3. PowerMaxExpress Compatible

WL Siren

The MCS-700/710 wireless siren can be

integrated with the PowerMaxExpress in areas

in which wiring action is difficult or impossible.

The MCS-700/710 is a fully supervised, 2-way

communication device (it includes a receiver,

to receive activation commands from the

alarm system, and a transmitter to periodically

transmit its status signal to the alarm system).

When an identifiable activation command is received from

the PowerMaxExpress, the siren activates its sounder and

the flash light (strobe light every 1.5 seconds).

Wireless

Siren

Industry Canada Declaration

This product meets the applicable Industry Canada technical specifications/Le présent materiel est conforme aux specifications techniques appliables d’Industrie Canada. The Ringer Equivalence Number is an indication of the maximum number of devices allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the RENs of all the devices does not exceed five/L’indice d’équivalence de la sonnerie (IES) sert à indiquer le nombre maximal de terminaux qui peuvent être raccordés à une interface téléphonique. La terminaison d’une interface peut consister en une combinaison quelconque de dispositifs, à la seule condition que la somme d’indices d’équivalence de la sonnerie de tous les dispositifs n’excède pas 5. The Ringer Equivalence Number (REN) for this terminal equipment is 0.3B.

D-302017 35

Page 36

WARRANTY

Visonic Limited (the “Manufacturer") warrants this product only (the "Product") to the original purchas er only (the

“Purchaser”) against defective workmanship and materials under normal use of the Product for a period of twelve

(12) months from the date of shipment by the Manufacturer.

This Warranty is absolutely conditional upon the Product having been properly installed, maintained and operated

under conditions of normal use in accordance with the Manufacturers recommended installation and operation

instructions. Products which have become defective for any other reason, according to the Manufacturers discretion,

such as improper installation, failure to follow recommended installation and operational ins tructions, neglect, willful

damage, misuse or vandalism, accidental damage, alteration or tampering, or repair by anyone other than the

manufacturer, are not covered by this Warranty.

The Manufacturer does not represent that this Produc t may not be compromised and/or circumvented or that the

Product will prevent any death and/or personal injury and/or damage to property resulting from burglary, robbery, fire

or otherwise, or that the Product will in all cases provide adequate warning or protection. The Product, properly

installed and maintained, only reduces the risk of such events without warning and it is not a guar antee or insurance

that such events will not occur.

THIS WARRANTY IS EXCLUSIVE AND EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, OBLIGATIONS

OR LIABILITIES, WHETHER WRITTEN, ORAL, EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY OF

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, OR OTHERWISE. IN NO CASE SHALL

THE MANUFACTURER BE LIABLE TO ANYONE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES

FOR BREACH OF THIS WARRANTY OR ANY OTHER WARRANTIES WHATSOEVER, AS AFORESAID.

THE MANUFACTURER SHALL IN NO EVENT BE LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL,

CONSEQUENTIAL OR PUNITIVE DAMAGES OR FOR LOSS, DAMAGE, OR EXPENSE, INCLUDING LOSS OF

USE, PROFITS, REVENUE, OR GOODWILL, DIRECTLY OR INDIRECTLY ARISING FROM PURCHASER’S USE

OR INABILITY TO USE THE PRODUCT, OR FOR LOSS OR DESTRUCTION OF OTHER PROPERTY OR FROM

ANY OTHER CAUSE, EVEN IF MANUFACTURER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH

DAMAGE.

THE MANUFACTURER SHALL HAVE NO LIABILITY FOR ANY DEATH, PERSONAL AND/OR BODILY INJURY

AND/OR DAMAGE TO PROPERTY OR OTHER LOSS WHETHER DIRECT, INDIRECT, INCIDENTAL,

CONSEQUENTIAL OR OTHERWISE, BASED ON A CLAIM THAT THE PRODUCT FAILED TO FUNCTION.

However, if the Manufacturer is held liable, whether directly or indirectly, for any loss or damage arising under this limited warranty, THE MANUFACTURER'S MAXIMUM LIABILITY (IF ANY) SHALL NOT IN ANY CASE EXCEED THE PURCHASE PRICE OF THE PRODUCT, which shall be fixed as liquidated damages and not as a penalty, and shall be the complete and exclusive remedy against the Manufacturer. When accepting the delivery of the Product, the Purchaser agrees to the said conditions of sale and warranty and he recognizes having been informed of. Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so these limitations may not apply under certain circumstances. The Manufacturer shall be under no liability whatsoever arising out of the corruption and/or malfunctioning of any telecommunication or electronic equipment or any programs. The Manufacturers obligations under this Warranty are limited solely to repair and/or replace at the Manufacturer’s discretion any Product or part thereof that may prove defective. Any repair and/or replacement shall not extend the original Warranty period. The Manuf acturer shall not be responsible for dismantling and/or reinstallation costs. To exercise this Warranty the Product must be returned to the Manufacturer freight pre-paid and insur ed. All freight and insurance costs are the responsibility of the Purchaser and are not inc luded in this Warranty. This warranty shall not be modified, varied or extended, and the Manufacturer does not authorize any person to act on its behalf in the modification, variation or extension of this warranty. This warranty shall apply to the Product only. All products, accessories or attachments of others used in conjunction with the Product, including batteries, shall be covered solely by their own warranty, if any. The Manufacturer shall not be liable for any damage or loss whatsoever, whether directly, indirectly, incidentally, consequentially or otherwise, caused by the malfunction of the Product due to products, accessories, or attachments of other s, including batteries, used in conjunction with the Products. This Warranty is exclusive to the original Purc haser and is not assignable. This Warranty is in addition to and does not aff ect your legal rights. Any provision in this warranty which is contrary to the Law in the state or country were the Product is supplied shall not apply.

The user must follow the Manufacturer’s installation and operational instruct ions including testing the

Warning:

Product and its whole system at least once a week and to take all necessary precautions for his/ her safety and the protection of his/her property.

VISONIC LTD. (ISRAEL): P.O.B 22020 TEL-AVIV 61220 ISRAEL. PHONE: (972-3) 645-6789, FAX: (972-3) 645-6788

VISONIC INC. (U.S.A.): 65 WEST DUDLEY TOWN ROAD, BLOOMFIELD CT. 06002-1376. PHONE: (860) 243-0833, (800) 223-0020. FAX: (860) 242-8094

VISONIC LTD. (UK): 7 COPPERHOUSE COURT, CALDECOTTE, MILTON KEYNES. MK7 8NL. PHONE: (0870) 7300800 FAX: (0870) 7300801 PRODUCT SUPPORT ( 0870) 7300830

VISONIC GMBH (D): KIRCHFELDSTR. 118, D-42015 DÜSSELDORF, GERMANY, FAX (0211) 60069619 Email: info-dach@visonic.com

VISONIC IBERICA: ISLA DE PALMA, 32 NAVE 7, PO LÍGONO INDUSTRIAL NORTE, 28700 SAN SEBASTIÁN DE LOS REYES, (MADRID), ESPAÑA.

TEL (34) 91659-3120, FAX (34) 91663-8468. www.visonic-iberica.es

: www.visonic.com

INTERNET

1/08

36 D-302017