The PB-101 PG2 and PB-102 PG2 are miniature PowerG
pendants, designed for use with PowerMaster control panels and
other PowerG receivers.
To activate transmission, press the pushbutton(s) at the center of
the unit. When activated, the transmitter sends out an alarm code,
and a buzzer sound and the LED light indicates confirmation about
successful or failed transmission.
The PB-101/102 has several options for carrying or mounting it.
The unit is supplied with a belt clip, a key chain, a lanyard
necklace, and a holder which can be attached to the belt clip or
mounted on a wall.
2.
2. OPERATION
OPERATION
2. 2.
OPERATIONOPERATION
The following functions are available:
Panic
The signal will notify
your central monitoring
station of an emergency
Press and hold the button down for
2 – 7 seconds.
Installation Instructions
Figure 1. PB-101 and PB-102
Press and hold both buttons down
simultaneously for more than 3
seconds.
No activity
Arm
Arm your system in the
Disarm
3. ASSEMBLY FOR
3. ASSEMBLY FOR PORTABILITY AND
3. ASSEMBLY FOR 3. ASSEMBLY FOR
This section describes how to attach the PB-101/102 to various portability options.
WARNING! Choking Hazard; Small parts; The pendant and belt clip are NOT for children under 3 years.
1. Slide the PB-101/102 into the holder until you feel it snap securely
inside.
2. To attach the belt clip, slide it onto the rails on the rear of the
holder.
3. To remove the PB-101/102 from the wall-mounted holder or from
Figure 2 Attaching PB-101/102 to a Belt Clip
---
---
Press and release the button in less
Not applicable
Not applicable
PORTABILITY AND MOUNTING
PORTABILITY AND PORTABILITY AND
MOUNTING
MOUNTINGMOUNTING
the belt clip, press down the top of the holder and push the pendant
up with your fingers.
Figure 4 Attaching PB-101/102 to a Lanyard Necklace
---
Figure 3 Attaching PB-101/102 to a Key Chain
Not applicable
Press and hold this button for less than
7 seconds.
Press and hold this button for less than
D-304457 PB-101/102 User’s Guide 1
This side
facing up
1. Using the two screws and plastic anchors included in the PB101/102 box, align the holder facing up and secure the holder to the
wall.
2. Slide the PB-101/102 into the holder until you feel it snap securely
inside.
4444. ENROLLMENT OF PB
. ENROLLMENT OF PB----101/102
. ENROLLMENT OF PB. ENROLLMENT OF PB
The Enrollment process “teaches” the system’s control panel the ID
of the PB-101/102 and enables the PB-101/102 to communicate with
the panel.
1. Enter the PowerMaster panel’s Installer menu and select
“02:ZONES/DEVICES”.
2. Select "ADD NEW DEVICE" Option.
5555. TESTING AND MAINTENANCE
. TESTING AND MAINTENANCE
. TESTING AND MAINTENANCE. TESTING AND MAINTENANCE
Figure 5 Attaching PB-101/102 to a Wall Mount
101/102
101/102101/102
5.1 Testing a New Unit
Since the PB-101/102 is supplied with the battery already
installed, the unit is practically ready to be tested.
IMPORTANT! Before testing, enroll the PB-101/102 in the
target control panel as instructed in the panel’s
programming instructions.
1. Stand 3 m (10 ft) away from the control panel and press the
buttons. Verify that the transmit LED lights.
2. Make sure that the control panel responds as programmed and
3. To remove the PB 101/102 from the holder, press down the top of
the holder and push the pendant up with your fingers as illustrated in
Figure 2.
3. Stand near the PowerMaster panel. Press and hold the
button (for PB-101) or the left button (for PB-102) until the
yellow LED turns on, and then release the button. Ensure that
the LED stays on for 2 seconds and then flashes for 10
seconds.
as stated in the panel’s programming instructions.
3. Operate the pendant from various locations within the area
covered by the receiver to determine "dead" locations, where
transmission is blocked by walls and large objects, or affected
by structural materials.
Note: If dead/marginal zones are a problem, relocating the
receiver may improve the performance.
5.2 Replacing the Battery
Replace the battery at least once every 5 years, or upon
observing that the LED flickers when transmitting. The required
battery is CR2032 Lithium 3V, manufactured by VARTA or
another UL-recognized manufacturer, purchased from a Visonicapproved supplier.
NOTE: The polarity of the battery must be observed, as
shown in Figure 7. Improper handling of lithium batteries
may result in heat generation, explosion or fire, which may
lead to personal injuries.
WARNING: Danger of explosion if batteries are installed
incorrectly. Replace only with the same or equivalent type
recommended by the manufacturer. Keep away from small
children. If batteries are swallowed, promptly see a doctor.
Do not try to recharge these batteries. Disposal of used
batteries must be made in accordance with the waste
recovery and recycling regulations in your area.
2
1. Insert a coin into the slot on the bottom center of the device
and twist to separate the two sides.
2. Then, slide the coin to the corner of the device and twist again
to remove the cover.
Figure 6. Opening the PB-101/102
Note: Make sure the elastic pad within the cover remains in
place. Put it back in place if it falls off.
D-304457 PB-101/102 User’s Guide
3. Extract the old battery from its holder, and replace it with a
recommended new battery. Ensure that the plus side of the
battery faces up, attaining correct polarity.
4. Test the unit by momentarily pressing one of the transmit
switches. The LED indicator should light.
+
CR2032
LITHIUM BATTERY
3V
Figure 7. Replacing the Battery
5. Put the covers back on securely, verifying that it snaps shut.
5.3 Cleaning
The pendant may get dirty if touched with greasy fingers. Clean it
only with a soft cloth or sponge moistened lightly with a mixture of
water and mild detergent, and wipe it dry immediately.
6. PRODUCT LI
6. PRODUCT LIMITATIONS
6. PRODUCT LI6. PRODUCT LI
Visonic wireless systems are very reliable and are tested to high standards. However, due to their low transmitting power and limited
range (required by FCC and other regulatory authorities), there are some limitations to be considered:
A. Receivers may be blocked by radio signals occurring on or near their operating frequencies, regardless of the code selected.
B. A receiver can only respond to one transmitted signal at a time.
C. Wireless equipment should be tested regularly to determine whether there are sources of interference and to protect against faults.
MITATIONS
MITATIONSMITATIONS
The use of abrasives of any kind is strictly forbidden. Also
never use solvents such as kerosene, acetone or thinner.
Do not submerge this product in any liquid, in order to
prevent damage to the electronic circuits.
Frequency Allocations for Wireless Devices in European (EU) Countries
433.92 MHz has no restriction in any EU member state.
7777. COMPLIANCE WITH STANDARDS
. COMPLIANCE WITH STANDARDS
. COMPLIANCE WITH STANDARDS. COMPLIANCE WITH STANDARDS
EN 300220, EN 301489 EN 50130-4, EN 61000-6-3, EN 60950-1
EN 50131-1 Security Grade
EN 50131-1 Environmental Class
FCC Compliance Statement
The digital circuitry of this device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in residential installations. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio and television reception. However, there is no guarantee that interference will not occur in a particular installation. If this
device does cause such interference, which can be verified by turning the device off and on, the user is encouraged to eliminate the interference
by one or more of the following measures:
– Re-orient or re-locate the receiving antenna.
– Increase the distance between the device and the receiver.
– Connect the device to an outlet on a circuit different from the one which supplies power to the receiver.
– Consult the dealer or an experienced radio/TV technician
This equipment complies with FCC and IC RF radiation exposure limits set forth for an uncontrolled environment.
WARNING! Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority
to operate the equipment.
This device complies with FCC Rules Part 15 and with Industry Canada licence-exempt RSS standard(s). Operation is subject to two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference that may be received or that
may cause undesired operation.
Le present appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisee
aux deux conditions suivantes :(1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage
radioelectrique subi, meme si le brouillage est susceptible d'en compromettre le fonctionnement.
The PB-101 PG2 and PB-102 PG2 are compatible with the RTTE requirements - Directive 1999/5/EC
of the European Parliament and of the Council of 9 March 1999 and EN50131-1 Grade 2 Class I.
USA: CFR 47 part 15 (FCC)
Canada: RSS 210
The Power G peripheral devices have two- way communication functionality, providing additional
benefits as described in the technical brochure. This functionality has not been tested to comply with
the respective technical requirements and should therefore be considered outside the scope of the
product’s certification.
According to EN 50131-1: this equipment can be applied in installed systems up to and including
Security Grade 2.
Class I
D-304457 PB-101/102 User’s Guide 3
Frequency Band (MHz)
Europe and rest of world:
433-434.72
,
868-86
9.15 USA: 912-919.185
Battery type
V
arta
3V CR
-
2032 Lithium battery
.
Low Battery Threshold
2.1 V
Battery Life Expectancy
5 years (for typical use)
Operating Temperature
0
° to 50°C (32° to 122°F)
Humidity
Average relative humidity
(RH) ∼ 75% non
-
condensing
, max 95% 30 days/yea
r
Dimension
s (LxWxD)
53
x 33 x 11 mm (2.
1 x 1.3 x 0.4
3 in)
Weight
15 gm (0.5 oz)
Weight (including battery)
20 gm (0.7 oz)
W.E.E.E. Product Recycling Declaration
Directive 2002/96/EC W aste
Electrical and Electronic Equipment.
When this product is out of use, please remove al l batteries and dispose of them separately. Bring electrical appliances to t
he local collecting points for waste electrical and
electronic equipment. Batteries are har
mful to health and the environment. Please help to protect the environment from health risks.
Visonic (the “Vendor") warrants this product only (the "Product") to the ori ginal
However, if the Vendor i
s held liable, whether directly or indirectly, for any loss or
W.E.E.E. Product Recycling Declaration
8888. SPECIFICATIONS
. SPECIFICATIONS
. SPECIFICATIONS. SPECIFICATIONS
For i nformation regarding the recycling of thi s product you must contact the company from which you orignially purchased it. If you are discarding this product and not
returning it for repair then you must ensure that it is returned as identified by your supplier. This product is not to be thrown away with everyday waste.
WARRANTY
purchaser only (the “Purchaser”) against defective workmanship and materials under
normal use of the Product for a period of twelve (12) months from the date of shi pment
by the Vendor.
This Warranty is absolutely conditional upon the Product having been properly installed,
maintained and operated under conditions of normal use in accordance with the
Vendors recommended installation and operation instructions. Products which have
become defective for any other reason, according to the Vendors discretion, such as
improper installation, failure to follow recommended installation and operational
instructions, neglect, willful damage, misuse or vandalism, accidental damage, alteration
or tampering, or repai r by anyone other than the vendor, are not covered by this
Warranty.
The Vendor does not represent that this Product may not be compromised and/or
circumvented or that the Product will prevent any death and/or personal injury and/or
damage to property resulting from burglary, robbery, fire or otherwise, or that the
Product will in all cases provi de adequate warning or protection. The Product, properly
installed and maintained, only reduces the risk of such events without warning and it is
not a guarantee or insurance that such events will not occur.
THIS WARRANTY IS EXCLUSIVE AND EXPRESSLY IN LIEU OF ALL OTHER
WARRANTIES, OBLIGATIONS OR LIABILITIES, WHETHER WRITTEN, ORAL,
EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE, OR OTHERWISE. IN NO CASE SHALL
THE VENDOR BE LIABLE TO ANYONE FOR ANY CONSEQUENTIAL OR
INCIDENTAL DAMAGES FOR BREACH OF THIS WARRANTY OR ANY OTHER
WARRANTIES WHATSOEVER, AS AFORESAID.
THE VENDOR SHALL IN NO EVENT BE LIABLE FOR ANY SPECIAL, INDIRECT,
INCIDENTAL, CONSEQUENTIAL OR PUNITIVE DAMAGES OR FOR LOSS,
DAMAGE, OR EXPENSE, INCLUDING LOSS OF USE, PROFITS, REVENUE, OR
GOODWILL, DIRECTLY OR INDIRECTLY ARISING FROM PURCHASER’S USE OR
INABILITY TO USE THE PRODUCT, OR FOR LOSS OR DESTRUCTION OF OTHER
PROPERTY OR FROM ANY OTHER CAUSE, EVEN IF VENDOR HAS BEEN ADVISED
OF THE POSSIBILITY OF SUCH DAMAGE.
THE VENDOR SHALL HAVE NO LIABILITY FOR ANY DEATH, PERSONAL AND/OR
BODILY INJURY AND/OR DAMAGE TO PROPERTY OR OTHER LOSS WHETHER
DIRECT, INDIRECT, INCIDENTAL, CONSEQUENTIAL OR OTHERWISE, BASED ON
A CLAIM THAT THE PRODUCT FAILED TO FUNCTION.
For i nformation regarding the recycling of thi s product you must contact the company from which you orignially purchased it. If you are discarding this product and not
returning it for repair then you must ensure that it is returned as identified by your supplier. This product is not to be thrown away with everyday waste.
Directive 2002/96/EC W aste Electrical and Electronic Equipment.
damage arising under this limited warranty, THE VENDOR'S MAXIMUM LIABILITY (IF
ANY) SHALL NOT IN ANY CASE EXCEED THE PURCHASE PRICE OF THE
PRODUCT, which shall be fixed as liquidated damages and not as a penal ty, and shall
be the complete and exclusive remedy against the Vendor.
When accepting the delivery of the Product, the Purchaser agrees to the said condi tions
of sale and warranty and he recogni zes having been informed of.
Some jurisdictions do not allow the exclusion or limitation of inci dental or consequential
damages, so these limitations may not apply under certain circumstances.
The Vendor shall be under no liabi lity whatsoever arising out of the corruption and/or
malfunctioning of any telecommunication or electronic equipment or any programs.
The Vendors obli gations under this W arranty are limited solely to repai r and/or replace
at the Vendor’s discretion any Product or part thereof that may prove defective. Any
repair and/or replacement shall not extend the original Warranty period. The Vendor
shall not be responsible for dismantling and/or reinstallation costs. To exercise this
Warranty the Product must be returned to the Vendor freight pre-paid and insured. All
freight and insurance costs are the responsibility of the Purchaser and are not i ncluded
in this Warranty.
This warranty shall not be modified, varied or extended, and the Vendor does not
authorize any person to act on its behalf in the modifi cation, variation or extension of this
warranty. This warranty shall apply to the Product only. All products, accessories or
attachments of others used in conjunction with the Product, incl uding batteri es, shall be
covered solely by their own warranty, if any. The Vendor shall not be liable for any
damage or loss whatsoever, whether directly, indirectly, incidental ly, consequentially or
otherwise, caused by the malfunction of the Product due to products, accessories, or
attachments of others, includi ng batteries, used i n conjunction with the Products. This
Warranty is exclusive to the original Purchaser and is not assignable.
This Warranty is in addition to and does not affect your legal rights. Any provision in this
warranty which is contrary to the Law in the state or country were the Product i s supplied
shall not apply.
Warning: The user must follow the Vendor’s installation and operational instructions
including testing the Product and its whole system at least once a week and to take all
necessary precautions for his/her safety and the protection of his/her property.