Visonic PB-101 PG2, PB-102 PG2 User Manual
Function
PB-
101 PB-102
PB
PB----101
PBPB
PB
PB----102
PBPB
101 PG2 /
101101
102 PG2
102102
PG2 /
PG2 / PG2 /
PG2
PG2PG2
Wireless Panic Button
1. INTRODUCTION
1. INTRODUCTION
1. INTRODUCTION1. INTRODUCTION
The PB-101 PG2 and PB-102 PG2 are small PowerG pendants,
designed for use with PowerMaster control panels and other
PowerG receivers.
To activate transmission, press the pushbutton(s) at the center of
the unit. When activated, the transmitter sends an alarm code, a
LED indication that confirms successful or failed transmission, and
(only in PB-102) a buzzer sound.
The PB-101/102 has several options for carrying or mounting it.
The unit is supplied with a belt clip, a key chain, a lanyard
necklace, and a holder which can be attached to the belt clip or
mounted on a wall.
2.
2. OPERATION
OPERATION
2. 2.
OPERATIONOPERATION
User’s Guide
Figure 1. PB-101 and PB-102
CAUTION: This equipment shall be used in non-hazardous locations only.
The following functions are available:
Panic
The signal will notify your
central monitoring station of
an emergency situation.
Arm
Arm your system in the Away
mode.
Disarm
Disarm your system.
3. ASSEMBLY FOR
3. ASSEMBLY FOR PORTABILITY AND
3. ASSEMBLY FOR 3. ASSEMBLY FOR
This section describes how to attach the PB-101/102 to various portability options.
WARNING! Choking Hazard; Small parts; The pendant and belt clip are NOT for children under 3 years.
---
---
Press and hold the button down for
2 – 7 seconds.
Not applicable
Not applicable
PORTABILITY AND MOUNTING
PORTABILITY AND PORTABILITY AND
MOUNTING
MOUNTINGMOUNTING
3. To remove the PB-101/102 from the wall-mounted holder or from
the belt clip, press down the top of the holder and push the pendant
up with your fingers.
Figure 3 Attaching PB-101/102 to a Key Chain
Press and hold both buttons down
simultaneously for more than 3
seconds.
Press and hold this button for at least 1
second.
Press and hold this button for at least 1
second.
1. Slide the PB-101/102 into the holder until you feel it snap securely
Figure 2 Attaching PB-101/102 to a Belt Clip
inside.
2. To attach the belt clip, slide it onto the rails on the rear of the
holder.
D-304457 PB-101/102 User’s Guide 1
Figure 4 Attaching PB-101/102 to a Lanyard Necklace
This side
facing up
Figure 5 Attaching PB-101/102 to a Wall Mount
1. Using the two screws and plastic anchors included in the PB-
101/102 box, align the holder facing up and secure the holder to
the wall.
2. Slide the PB-101/102 into the holder until you feel it snap securely
inside.
3. To remove the PB 101/102 from the holder, press down the top of
the holder and push the pendant up with your fingers as illustrated
in Figure 2.
4444. ENROLLMENT
. ENROLLMENT AND CONFIGURATION
. ENROLLMENT. ENROLLMENT
AND CONFIGURATION OF PB
AND CONFIGURATIONAND CONFIGURATION
OF PB----101/102
OF PBOF PB
101/102
101/102101/102
4.1 Enrollment
The Enrollment process “teaches” the system’s control panel the ID of the PB-101/102 and enables the PB-101/102 to communicate with the
panel.
1. Enter the PowerMaster panel’s Installer menu and select “02:ZONES/DEVICES”.
2. Select "ADD NEW DEVICE" Option.
3. Stand near the PowerMaster panel. Press and hold the button (for PB-101 PG2) or the left button (for PB-102 PG2) until the
yellow LED turns on, and then release the button. Ensure that the LED stays on for 2 seconds and then flashes for 10 seconds.
4.2 Configuring the Panic Button Parameters (for PowerG Version 18 systems only)
Enter the DEVICE SETTINGS menu and follow the configuration instructions for the PB-101 PG2 and PB-102 PG2 panic buttons as described
below.
Option Configuration Instructions
Functionality1
Supervision
Define whether to use to Arm/Disarm or to operate the PGM.
Optional settings: Arm/Disarm (default) and PGM ON/OFF.
Define whether the control panel will monitor supervision messages sent by the panic button for a time period of
8 hours.
Optional settings: Disabled (default) and Enabled.
5555. TESTING AND MAINTENANCE
. TESTING AND MAINTENANCE
. TESTING AND MAINTENANCE. TESTING AND MAINTENANCE
5.1 Testing a New Unit
Since the PB-101/102 is supplied with the battery already
installed, the unit is practically ready to be tested.
IMPORTANT! Before testing, enroll the PB-101/102 in the
target control panel as instructed in the panel’s
programming instructions.
1. Stand 3 m (10 ft) away from the control panel and press the
buttons. Verify that the transmit LED lights.
2. Make sure that the control panel responds as programmed and
as stated in the panel’s programming instructions.
1
Applies to PB-102 PG2 only
2 D-304457 PB-101/102 User’s Guide
3. Operate the pendant from various locations within the area
covered by the receiver to determine "dead" locations, where
transmission is blocked by walls and large objects, or affected
by structural materials.
Note: If dead/marginal zones are a problem, relocating the
receiver may improve the performance.
Loading...