Visonic NEXT PG2, NEXTK9-85PG2 Installation Instructions Manual

D-302413 NEXT PG2, NEXT K9-85 PG2 Installation Instructions 1

NEXT PG2

NEXT PG2NEXT PG2

NEXT PG2 /

/ /

/

NEXT

NEXTNEXT

NEXT K9

K9K9

K9----85

8585

85 PG2

PG2PG2

PG2

PowerG, Wireless, PIR /Pet Tolerant Motion Detector

Installation Instructions

1. INTRODUCTION

1. INTRODUCTION1. INTRODUCTION

1. INTRODUCTION

The Next PG2 and Next K9-85 PG2 are 2-way, microprocessor-controlled, wireless digital PIR detectors.
The detectors features are as follows:

• For use with all PowerMaster® control panels (version 10 and higher).

• Combined Fresnel and cylindrical optics, up to 15 meters (49 ft).

• The Next PG2 includes wall creep zone protection.

• In Next PG2 and Next K9-85 PG2, Target Specific Imaging™ (TSI) technology is used for distinction

between human beings and pets weighing up to 38 kg (85lb).

• Includes a fully supervised PowerG transceiver.

• The advanced True Motion Recognition™ algorithm (patented) allows distinguishing between the true

motion of an intruder and any other disturbances which may cause false alarms.

• Sophisticated frequency domain digital signal processing.

• Built-in link quality indicators; no need for the installer to physically approach the control panel thus making

installation faster and easier.

B

A

A. LED
B. Lens

Figure 1: External View

• No vertical adjustment is needed.

• Motion event counter determines whether 1 or 2 consecutive motion events will trigger an alarm.

• Automatic termination of walk-test after 15 minutes.

• Microprocessor-controlled temperature compensation.

• Sealed chamber protects the optical system.

• Front cover and back tamper switches, for improved tamper protection.

• White light protection.

• Notes: 1. The pet immunity feature was not evaluated by UL.

2. For CE installations, the pet immunity was not evaluated by DNV.

3. The pet immunity feature is not evaluated and certified by Applica Test & Certification AS.

2222.

. .

. INSTALLATION

INSTALLATIONINSTALLATION

INSTALLATION

2.1 General Guidance (see Fig. 2)

1. Keep away from heat sources.

2. Do not expose to air drafts.

3. Do not install outdoors.

4. Avoid direct sunshine.

5. Keep wiring away from power cables.

6. Do not install behind partitions.

7. Mount on solid stable surface.

8. Installed in accordance with NEC, NFPA 70.

9. Installed in accordance with UL 681, Standard for
Installations and Classifications of burglar and Holdup
Alarm Systems.

1 2 3

4 5 6

7

Figure 2. General Guidelines

Important! The Next K9-85 PG2 detector is tolerant to 38 kg (85 lb) animals moving on the floor or climbing on
furniture as long as the activity takes place below 1 m (3 ft). Above the 1 m (3 ft) height limit, the detector is tolerant
to 19 kg (42 lb) pets, but the pet immunity will decrease as the pet gets closer to the detector. It is therefore
recommended to select a mounting location that minimizes potential close proximity of animals.

WARNING! To comply with FCC and IC RF exposure compliance requirements, the PIR detector should be located at a distance of at least 20
cm from all persons during normal operation. The antennas used for this product must not be co-located or operated in conjunction with any other
antenna or transmitter

2 D-302413 NEXT PG2, NEXT K9-85 PG2 Installation Instructions

2.2 Mounting (see Fig. 3)

Notes:

1. Mount the detector so that its orientation is perpendicular to the expected intrusion path.

2. For installations of detector at 2m high, Dead zone is 2ft at 0m high and 0.5ft at 1.5m high.

1

2

3

B

A

4

C D

1. Release screw and remove cover.

2. Push catch and remove board.

3. Insert battery.

4. Mounting

A. Front Tamper switch
B. Back Tamper switch.
C. On surface
D. In corner

Caution!

Risk of explosion if battery is replaced by an incorrect type. Dispose of used battery according to manufacturer's instructions.

Note: Back Tamper must be enabled for UL installations.Figure 3. Mounting

2.3. Enrollment

Refer to the PowerMaster panel's Installer Guide and follow the procedure under the "02:ZONES/

02:ZONES/02:ZONES/

02:ZONES/ DEVICES

DEVICESDEVICES

DEVICES" option of the Installer Menu.

A general description of the procedure is provided in the following flow chart.

Step 1 Step 2 Step 3 Step 4 Step 5 Step 6

Enter the Installer menu

and select

“02:ZONES/DEVICES”

Select "ADD NEW

DEVICE" Option

See Note [1]

Enroll the device or Enter

the device ID

Select the desired Zone

Number

Configure Location,

Zone Type &

Chime Parameters

Configure

the

Detector











 means scroll and select

See Note

[2]

Notes:
[1] If the detector is already enrolled you can configure the detector parameters via the “Modify Devices” option – see Step 2.
[2] Select the "Device Settings" option and refer to section 2.4 to configure the detector parameters.

2.4. Configuring the Detector Parameters

Enter the menu and follow the configuration instructions for the Next PG2 / Next K9-85 PG2 PIR detector as described in
the following table.

Option Configuration Instructions

Here you determine whether or not the alarm LED indication will be activated.

Optional settings: LED ON (default) and LED OFF.

•

•

Here you determine whether an alarm will be activated upon continued motion (low sensitivity) or upon a single
alarm event (high sensitivity)..

Optional settings: LOW sensitive (default) and HIGH sensitive.

•

•

Here you determine whether or not to set the activity time during disarm.

Optional settings: NOT Active (default), YES – no delay, YES + 5s delay, YES + 15s delay, YES + 30s delay,

YES + 1m delay, YES + 2m delay, YES + 5m delay, YES + 10m delay, YES + 20m delay and YES + 60m
delay.

•

•

DISARM Activity

Event Counter

Alarm LED

DEVICE SETTINGS

Z14.DEV SETTINGS

Z14.SET CHIME

Z14.ZONE TYPE

Z14.LOCATION

ID No. 120-XXXX

Z14:Motion Sens

ENTR ID:XXX-XXXX

ENROLL NOW or

MODIFY DEVICES

ADD NEW DEVICES

02.ZONES/DEVICES