Page 1
500 South CP Avenue • P.O. Box 280 • Lake Mills. WI 53551
toll free 800.335.4348 • phone 920.648.4090 • fax 920.648.3373
www.visionfitness.com
©2008 Vision Fitness. All Rights Reserved. 3.08
AG18.49PRD
REV6
Assembly
Guide
X6750HRT
COMMERCIAL INCLINE ELLIPTICAL TRAINERS
6mm T-Shaped Wrench
Screwdriver
5mm L-Shaped Wrench
TOOLS & PARTS INCLUDED
PARTS BOX
Power Cord
Console Mast Bracket
Console Mast Cover
Accessory Tray
Color-coded Hardware Bags
Owner’s Guide
Assembly Guide
Warranty Card
13mm Wrench
6mm L-Shaped Wrench
17mm Wrench
8mm L-Shaped Wrench
Page 2
X6750HRT
COMMERCIAL INCLINE ELLIPTICAL TRAINERS
To avoid possible damage to this Elliptical Trainer, please follow these assembly steps in the correct order. Before proceeding, find your
new Elliptical Trainer’s serial number located on the front axle tube, and enter here:
ORANGE BAG
HARDWARE INCLUDED
BLACK BAG
Refer to this number when calling for service, and enter this serial number on your Warranty Card and in your own records.
Be sure to read your Owner’s Guide before using your new Elliptical Trainer.
If any parts, hardware or tools are missing, please call 1.800.335.4348, Extension 12
NOTE: It is recommended that you apply grease to the threads of each bolt and screw as you assemble your Elliptical Trainer to prevent
loosening and noise. Also, during each assembly step, ensure that ALL bolts and screws are in place and partially threaded in before
completely tightening any ONE bolt or screw.
HARDWARE INCLUDED
PINK BAG
M10x25L Socket Head Bolt
Quantity: 4
M8 Lock Washer
Quantity: 4
M8x25L Socket Head Bolt
Quantity: 4
8x16x2T Washer
Quantity: 4
M10 Lock Washer
Quantity: 4
Zip Tie, Quantity: 1
BLUE BAG
M5x12L Bolt
Quantity: 2
10x24.5x1T Washer
Quantity: 4
M10x55L Socket Head Bolt
Quantity: 2
M10 Nylon Nut
Quantity: 2
M8x20L Socket Head Bolt
Quantity: 4
GREEN BAG
26x36x0.3T Wave Washer
Quantity: 2
26x36x2T Wave Washer
Quantity: 4
25.5x38x1T Washer
Quantity: 2
8.2x18x1.5T Arc Washer
Quantity: 4
M8x12L Bolt
Quantity: 2
End Cap
illustration not to scale
Quantity: 2
Spacer
Quantity: 4
Plastic Connector
Quantity: 4
M8x25L Socket Head Bolt
Quantity: 8
M8x55L Socket Head Bolt
Quantity: 2
YELLOW BAG
M8x20L Panhead Bolt
Quantity: 4
8x16x1T Washer
Quantity: 2
M8 Nylon Nut
Quantity: 2
M5x15L Bolt
Quantity: 8
M8 Lock Washer
Quantity: 8
Page 3
4
STEP
• Remove protective covers from sleeves
of the pedal arms.
IMPORTANT:
The washers in the
following step must be assembled in
the correct order.
• Slide one thin metal wave washer
(26x36x0.3T)
, one flat washer
(25.5x38x1T)
,
and one plastic wave washer
(26x36x2T)
onto the axle of the right link arm. Slide
the axle of the right link arm through the
sleeve on the right pedal arm. Secure
the link arm onto the pedal arm with the
plastic wave washer (26x36x2T), end
cap, and bolt (M8x12L). Tighten with
the 5mm L-shaped wrench.
• Repeat the step on the left side.
GREEN BAG
5
STEP
NOTE:
With this next step it is helpful
to have a second person to hold the
dual-action arms in place while you
assemble them.
• Take the right dual-action arm and
center the holes in the rotation housing
on the console mast. Secure with four
socket head bolts (M8x25L) and four
lock washers (M8). Tighten with the
6mm T-shaped wrench.
• Attach the dual-action arm rotation
cover to the dual-action arm center.
Secure in place with two bolts
(M5x15L). Tighten with the screwdriver.
• Slide a spacer onto each side of the
socket joint located on the end of the
link arm. Slide the bottom of the dualaction arm bracket over the link arm
socket and spacers. From the outside
of the bracket, slide the bolt (M8x55L)
through the hole in the bracket and
socket joint. Secure with a washer
(8x16x1T) and nylon nut (M8).
Tighten with the 6mm T-shaped
wrench and 13mm wrench.
• Attach the inside dual-action arm
cover onto the bottom of the dualaction arm with a bolt (M5x15L).
Insert the plastic connector to the
inside dual-action arm cover. Slide the
outside dual-action arm cover onto the
other end of the plastic connector.
Secure the outside dual-action arm
cover to the bottom of the dual-action
arm with a bolt (M5x15L). Tighten
both bolts with the screwdriver.
• Repeat these steps on the left side.
BLACK BAG
3
STEP
6
STEP
• Slide the accessory tray onto the
console mast. Secure in place with
four panhead bolts (M8x20L). Tighten
with the 5mm L-shaped wrench.
• Remove the four bolts (M5x12L)
from the back side of the console.
Connect the data cable and the heart
rate wires to the plugs in the back side
of the console. Place the console on
the mast and secure in place with the
bolts (M5x12L).
• Place the X6750HRT in its intended
location and plug in the power cord
to the electrical outlet.
YELLOW BAG
4
STEP
6
STEP
5
STEP
Console Mast
Boot
Mounting Plate
Console Mast
Frame Bracket
Rotation
Housing
Dual-Action
Arm
Console
Accessory Tray
2
STEP
1
STEP
Front Stabilizer Tube
2
STEP
• Take the right pedal arm and set the
roller wheel in the aluminum guide track.
Slide the opposite end of the pedal arm
into the U-shaped knuckle bracket.
Slide a socket head bolt (M10x55L)
with a washer (10x24.5x1T) through
the hole in the knuckle bracket and
pedal arm. Fix in place with a
washer (10x24.5x1T) and nylon nut
(M10). Tighten with the 8mm L-shaped
wrench and the 17mm wrench.
• Slide the pedal arm cover over the
knuckle joint and fix in place with a bolt
(M5x12L). Tighten with the screwdriver.
• Repeat these steps on the left side.
BLUE BAG
Console Plate
Knuckle Bracket
1
STEP
• Place a piece of packaging under
the front of the unit to aid in assembly
of the front foot.
• Secure the front stabilizer tube to the
base frame plate with four socket
head bolts (M8x20L) and four arc
washers (8.2x18x1.5T). Tighten with
the 6mm L-shaped wrench.
• Remove the packaging from under
the front of the unit.
ORANGE BAG
3
STEP
• Slide the console mast boot onto the
console mast.
• Attach the mounting plate to the
bottom of the console mast with four
socket head bolts (M10x25L) and four
lock washers (M10). Tighten as much as
possible with the 8mm L-shaped wrench.
• Mount the console mast on the
frame by sliding the guide hole on the
mast mounting plate over the guide
screw on the front of the frame bracket.
Place a lock washer (M8) followed by
a flat washer (8x16x2T) on each of
the four remaining socket head bolts
(M8x25L). Insert the bolts to the rear
holes but do not completely tighten.
Next, insert the bolts to the front holes.
Tighten all four bolts as much as possible
with the 6mm L-shaped wrench.
• Wrap the wire tie that exits the hole
at the bottom front side of the console
mast around the wire harness coming
up from the frame. Pull the wire tie
and wire harness up through the top
of the console mast.
• Insert a zip tie through the hole in
the middle of the console plate and
loop it around the heart rate wires and
wire harness. Pull to snug, but do not
over tighten.
PINK BAG
Link Arm
Pedal Arm
Thin Metal
Wave Washer
Flat Washer
Plastic Wave
Washer
Plastic Wave
Washer
End Cap
Loading...