Vision Fitness T9450HRT, T9350HRT User Manual

Assembly

Guide

T9250, T9350HRT AND T9450HRT

FOLDING TREADMILLS

1

STEP

2

STEP

5

STEP

To avoid possible damage to this Folding Treadmill, please follow these assembly steps in the correct order. Before proceeding
though, find your new Folding Treadmill’s serial number, located on the underside of the main frame, and enter here:

Refer to this number when calling for service, and also enter this serial number on your Warranty Card and in your own records.
Be sure to read your Owner’s Guide before using your new Folding Treadmill.

If any parts, hardware or tools are missing, please call 1.800.335.4348, Extension 12

NOTE: It is recommended that you apply grease to the threads of each bolt as you assemble your Folding Treadmill, to prevent loos-

ening and noise. Also, during each assembly step, ensure that ALL nuts and bolts are in place and partially threaded in before
completely tightening any ONE bolt.

Assembly

Guide

T9250, T9350HRT AND T9450HRT

FOLDING TREADMILLS

3

STEP

5mm Allen Wrench

Screwdriver

TOOLS, HARDWARE, & PARTS INCLUDED

PARTS BOX

Water Bottle, Qty: 1

Heart Rate Chest Strap, Qty: 1

(

Except T9250

)

Color-coded Hardware Bags

Owner’s Guide

Assembly Guide

Warranty Card

8mm Allen Wrench

HARDWARE INCLUDED

ORANGE BAG

BLUE BAG

PINK BAG

M8 x 50L V-Head Bolts

Quantity: 2

M8 x 20L Bolts

Quantity: 2

M4 x 12L V-head Screw

Quantity: 2

M8 x 135L Bolts

Quantity: 4

M8 x 20L Bolts

Quantity: 4

M4 x 12L V-head Flat Screw

Quantity: 4

5

1

STEP

2

STEP

1

STEP

• Fold up the right-hand console mast
to the vertical position. Be sure not to
pinch the data cables.

• Insert the bolt (M8 x 50L) in the side
and tighten with the blue-handled 5mm
Allen Wrench.

• Insert one bolt (M8 x 20L) in the front
and tighten with the blue-handled
5mm Allen Wrench.

• Repeat this on the opposite side.

NOTE: There are no data cables on
the left side.

ORANGE BAG

2

STEP

• Slide the base side covers down the
left-hand and right-hand console
masts.

• Fold the treadmill to the vertical
position.

• Secure the right-hand base side
cover to the base frame. Use the
V-head screw (M4 x 12L) for the rear
of the cover and the Flat screws
(M4 x 12L) for the front of the cover.
Repeat this step on the left-hand side.

• Unfold the treadmill.

BLUE BAG

6

3

STEP

3

STEP

• Mount the right-hand side mount
handlebars to the console mast using
two bolts (M8 x 135L). Repeat this on
the left-hand side.

• Plug in the large data cable into the
large plug connection in the connection
box on the right-hand side of the console.

• Plug in the small data cable into the
small plug connection in the
connection box on the right-hand side
of the console

NOTE: Push all extra data cable into
the console mast. Make sure not to
pinch or cut the data cable.

• Mount the console to the console
masts using four bolts (M8 x 20L)
and tighten with the blue-handled
5mm Allen wrench.

PINK BAG

7

4

STEP

Once the treadmill is plugged in, you need to perform an Auto-Calibration to assure maximum performance.

MODELS T9350HRT & T9450HRT:

DO NOT STAND ON THE BELT WHEN PERFORMING THE AUTO-CALIBRATION

• You need to access User Engineering Mode to run the Auto-Calibration. With the Safety Key in place, please
hold down SPEED DOWN and SELECT for 5 seconds. When in the User mode, "USEr" displays in the center
window. To access the data press the ELEVATION keys until "Auto" appears in the center window. Press Start to
select this function.

• To begin Auto-Calibration, press START. The treadmill will run through minimum and maximum Speed and
maximum Elevation. This will take 3-5 minutes. Let the treadmill perform this complete function before exiting the
Engineering Mode.

• Elevation A/D or Elevation in % appears in the left window. PWM value or Speed appears in the right
window. "End" will appear in the center window when the Auto-Calibration is complete. When Auto-Calibration
is complete, it will take the treadmill about 30 seconds to go to 0% Elevation and return to the start-up screen
with “P1” showing in the Function window.

MODEL T9250:

DO NOT STAND ON THE BELT WHEN PERFORMING THE AUTO-CALIBRATION

• With the Safety Key in place, hold the ELEVATION UP and SPEED DOWN buttons for 5 seconds. The console
will beep 5 times and a number will appear in the window. Shortly thereafter, “EnG1” will appear in the
window. Press the ELEVATION UP or SPEED UP to “EnG4.”

• Press START. The treadmill will Auto-Calibration itself. It will take 3-5 minutes. When the Auto-Calibration is
complete "END" will flash in the window. Wait 10 seconds.

• Remove the Safety Key. Then, put the Safety Key in place to use the treadmill.

AUTO-CALIBRATION

8

500 South CP Avenue • P.O. Box 280 • Lake Mills, WI 53551

toll free 1.800.335.4348 • phone [phone] • fax [phone]

www.visionfitness.com

©2004 Vision Fitness. All Rights Reserved. 7.04 Part #Z92TM42C-AG
AG18.31PRD
REV1

5

STEP

5

STEP

• If the running belt slips when used,
use the supplied 8mm Allen wrench to
turn the left and right tension bolts
clockwise 1/4-turn at a time until the
belt no longer slips.

• If the running belt is too far to the

right

side, use the supplied 8mm Allen

wrench to turn the

right

tension bolt

clockwise

1

/4-turn at a time until the
belt remains centered during use.
If the running belt is too far to the

left

side, turn the

left

tension bolt
clockwise 1/4-turn at a time until the
belt remains centered during use.

BELT TENSION