Page 1
ZA1002US-5
Z-Wave Smart Gateway
Installation&UserGuide
(ForPC)
Page 2
1
WELCOME
Congratulations on purchasing the ZA1002US-5. The ZA1002US-5 integrates multiple
complicated control, automation and internet protocols into one simple plug-and-play device.
It is a central controller that integrated and control of all wireless Z-wave devices used for
home automation and keeps connect and control of your home easily, nomatter where you
are.Please take a few minutes toread this guide to set up your ZA1002US-5 and Z-wave
network smoothly.
Page 3
2
Table of Contents
Chapter 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . 4
1.1 Key Features . . . . . . .. . . . . . . . . . . . . . . . . . . . . .. . . . .. . . . . . . . . . . . . . . . . . . . . . . . .. . . 4
1.2 .Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . 4
1.3 .Hardware Overview . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . .. . . . . . . . . . . . . . . . . . 5
1.3.1 Front Panel . . . . . .. . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . 5
1.3.2 Back Panel . . . . . .. . . . . . . .. . . . . . . . . . . . .. . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . 6
Chapter 2 Quick Install. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . 7
2.1 Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . .7
2.2 The Procedure of Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
2.3Find the IP address of your
ZA1002US-5 . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . .. . . . .. . . . .8
2.4 Setup Wi-Fi for your
ZA1002US-5. . . . . . . . . . . . . . . . . .. . . . . . . . . . . . .. . . . . . . . . . . . . . . . .. . . . .. . . . .8
2.4.1 System. . . . . . . . . . . . . . . . . .. . . . . . . . . . .. . . . . ... . . . . ... . . . . .. . . . . . . . . . . . .. . . . .. . . . .9
2.4.2 Network. . . . . . . . . . . . ... . . . . ... . . . . ... . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . .. . . . .. . . . .10
2.4.2.1 General Setup. . . . . . .. . . . . ... . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . .. . . . .. . . . .10
2.4.2.2 Advanced Settings. . . . . . . . . . . . . . . . . ... . . . . .. . . . . . . . . . . . . . . . . . . . . . .. . . . .. . . . .11
2.4.2.3 Physical Settings. . . . . ... . . . . ... . . . . ... . . . . .... . . . ... . . . . ... . . . . ... . . . . ... . . . ..12
2.4.2.4 Firewall Settingsb. . . ... . . . . ... . . . . ... . . . . ... . . . . ... . . . . ... . . . . ... . . . . ... . . . . ..12
2.4.3 Zwave. . . . . ... . . . . ... . . . . ... . . . . ... . .... . . . . ... . . . . ... . . . . ... . . . . ... . . . . ... . . . . ..13
2.4.4 Logout. . . . . . . . . .. . . . . . . . . .. . . . . . . . . .. . . . . . . . . .. . . . . . . . . .. . . . . . . . .. . . . . . . . . 13
2.5Initial setup procedure for ZA1002US-5 web
configuration . . . . . . . . . . .. . . . . . . . . . . . . . .. . . .. . . . .14
Chapter 3 Full web configurations . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . .. . . . . . . .15
3.1 Enter web configure page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
3.2 SetZwave– Z-Wave device settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
3.2.1 The Z-Wave device configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
3.2.1.1 Add a Z-Wave device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 17
3.2.1.2 Remove a Z-Wave device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
3.2.2 Z-Wave Control and Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . .21
3.2.3 Topology . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . .. . . . . . . . . . . . . . . . . . . .. . . . . . . . 22
3.2.4 Door Lock Security . . . . . . . .. . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . .23
3.2.5 Version Information . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
3.3 Room Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Page 4
3
3.3.1 Create Room . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
3.3.2 All Rooms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
3.4Device Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Page 5
4
Chapter 1 Introduction
ZA1002US-5is a central controller that integrated and control of all wireless Z-wave devices
used for home automation. It also providesGateway to connect to Internet. ThroughInternet
you can see all kinds of devices status of your home atanytimeand any place via your
smartphone or PC.You can control thehomedevices such aslighting, air conditioning, door
lock and unlock, you can also receivethealarmmessageof your home. Energy usage
monitorsof your homeat any timeis real-timerecordingto the cloudhost, homealarm
messagesareimmediatelydeliveredto the cloudmessagemonitoring
centerforthenecessarytreatment.
The ZA1002US-5 controls switches, dimmers, motion sensors, temperature sensors and so
on many Z-Wave devices. ZA1002US-5integrates complicated control, automation and
internet protocols into one simple plug-and-play device. It provides an interface that allows
you to manage your home easily, whether you are at home or not.
1.1Key Features
Provide one LAN port Router function
Provide one USB 2.0 Host port, you can connect ZigbeeUSB Dongle or USB Hard Disk
ProvideWiFiIEEE 802.11b/g/n
ProvidecompatibleZ-Wave Pluscommunication protocolthat connects allkinds of
Z-Wavedevices that includeswindow sensors, electric locks, lighting dimmer controls,
energy usage monitor, air qualitydetector, temperature and humidity sensors,
firesafetysensors.
Provide a service platform to connect to the cloudservice.
ProvideIP-Camviewinginterface
ProvidefreedownloadAPP.
1.2Technical Specifications
Technical Specifications
HardwareSpecifications
USB Port USB Host 2.0 x1
Ethernet port RJ-45 10/100Mb , support 1 LAN
Physical and Environmental Characteristics
Dimensions 137(W) x 101(H) x 30(D) mm
Weight 300g
Operating Temp.
Temp: 0°C~45°C (32°F~113°F)
Page 6
5
& Humidity
Humidity: 10%~90% relative humidity, non-condensing
Power Adaptor
INPUT: AC100V~240V, 50/60Hz
OUTPUT: DC 5V, 2.0A
outer casing Plastic
Country of origin
Made in Taiwan
SoftwareSpecifications
Protocol Z-Wave
WiFi IEEE 802.11b/g/n
HA Functions
Sense Control
Lighting Control
Door Lock Control
Sensor Trigger Even
Schedule setting
Support mobile phone Push Notification
Support Devices Place Location
User account Management (admin and normal user)
Support Remote update software
Z-Wave Capacity
Support 30 Z-Wave notes
1.3 Hardware Overview
1.3.1 Front Panel
Page 7
6
1.3.2 Back Panel
DC 5V/2A:Connecting to AC adapter.Input AC 100V~240V, 50/60Hz;
Output DC 5V 2.0A
LAN: RJ-45 socket, complied with Ethernet 10/100base-T.
USB:USB 2.0 ports, USB Type A
.
Connect to power supply
For Z-Wave
USB port
LAN port
Page 8
7
Chapter 2 Quick Install
After you’ve created your Z-Wave network, you’ll need to install your ZA1002US-5. Follow
these steps:
2.1 Unpacking
Open the carton and unpack the items. Your package should include:
ZA1002US-5main unit x 1 pcs
If items are missing or damaged, notify your Avadesignrepresentative. Keep the carton
and packing material.
2.2 The Procedure of Connection
Step 1: Plug in DC power adapter to ZA1002US-5.
Step 2: Connect the Ethernet cable to your ZA1002US-5LAN port.
Step 3: Plug in AC power cord to power source.
Step 4:ZA1002US-5 begins the boot process automatically.
ZA1002US-5 provides three kinds of operational platforms, Web page, Android and iOS, for
users. Therefore user can configure the ZA1002US-5 by his/her PC or smart phone or tablet.
The web configuration guide is available in this manual. The installation guide for
smartphone/tablet with Android system or iOS system, please refer to other document.
Ethernet cable
LAN port
Page 9
8
2.3Find the IP address of your ZA1002US-5
Please download the Java program file named avaControlFinderJava from the website of
Avadesign Co., Ltd. http://www.avadesign.com.tw/support/support.htmlto your PC.
Decompress the file and click it twice by left button of your mouse. Then you will see the
IP address listing of all of your ZA1002US-5 as below.
avaControl Finder
2.4 Setup Wi-Fi for your ZA1002US-5(optional)
If you want to use Wi-Fi, please following the setup procedure described as below.
Step 1: At first, connect Ethernet cable to LAN port of ZA1002US-5.
Step 2: Type the IP address which getting from avaControl Finder as Sec. 2.3. For example:
type 192.168.1.8 of the ZA1002US-5in the address bar and press Enter. The screen is
shown as follows.
The username is root.Please input password: 1234 then click “Login” button on the
screen. After login ZA1002US-5, you will see the login page as shown below.
Step 2-1: Please key in 192.168.1.8 of your AVA-88.
Step 2-2: Please input password. The default
password is 1234.
Step 2-3: Click on “Login” button.
Page 10
9
Step 3: Click on Network function in the top menu to setup your Wi-Fi network. The detailed
is described at Sec. 2.4.2.
Step 4: When Wi-Fi network configure has finished, please take off the Ethernet cable from
LAN port of ZA1002US-5.
Login page
After Login user will see the screen as above, and there are four maincategories in the top
menu, user can click on each category to extend detail items.
System
Network
Zwave
Logout
The various configuration menus are explained below. You can select various function listed
in the first line of web page display.
2.4.1 System
You can backup or flash firmware in this function. This function also providesreboot the
system for you.
Backup / Restore
You can click on "Generate archive" button on the screen to download a tar archive of the
current configuration files.
To restore configuration files, you also can upload a previously generated backup archive
here.
Flash new firmware image
You can upload a sysupgrade-compatible image here to replace the running firmware.
Page 11
10
Backup/Flash Firmware
2.4.2 Network
The network function provides Wi-Fi network configuration for users.
Network page
Click on “Edit” button, you can do general setup, or advanced settings, or physical settings
and Firewall settings.
2.4.2.1 General Setup
Page 12
11
General Setup
You can select which protocol you need. ZA1002US-5 provides a protocol listing of static
address, DHCP client, unmanaged, PPP, PPtP, PPPoE, PPPoATM, UMTS/GPRS/EV-DO
and L2TP for your choice.
2.4.2.2 Advanced Settings
You can do advanced configuration by clicking on “Advanced Settings” function.
Advanced Settings
Page 13
12
2.4.2.3 Physical Settings
You can create a bridge over specified interface and enables the Spanning Tree Protocol on
this bridge. You also can select which interface you needed by clicking the check squares.
Physical Settings
2.4.2.4 Firewall Settings
Choose the firewall zone you want to assign to this interface by clicking on “Firewall Settings”
function. Select“unspecified”to remove the interface from the associated zone or fill
out ”create”field to define a new zone and attach the interface to it.
Firewall Settings
Page 14
13
2.4.3 Zwave
You also can do Z-Wave devices setup by clicking on “Zwave” function. Please refer to
Chapter 3 for the detailed description.
ZWave home page
2.4.4 Logout
You can log out the system by clicking on “Logout” function.
Page 15
14
2.5Initial setup procedure for ZA1002US-5 web configuration
In order to set proper functions for each Z-Wave device, you can follow this flow chart before
you start to configure Z-Wave devices for ZA1002US-5.
START
Add the Z-wave device
Create Room
Create Scene
Create Trigger
Setup Schedule
Report
SetZwave
Please refer to section 3.2
Room
Please refer to section 3.3
Scene
Please refer to section 3.5
Trigger
Please refer to section 3.6
Schedule
Please refer to section 3.7
Report
Please refer to section 3.8
Function Name
in the top menu
Page 16
15
Chapter 3 Full web configurations
3.1 Enter web configure page
Move the cursor to the IP address of ZA1002US-5 on the screen and click it that as shown the
diagram of avaControl Finder at section 2.3. Then you will enter the web page for
configuration as follows.
Please input with username: admin and password: admin then click “Login” button on the
screen. After login ZA1002US-5, you will see the home page as shown below.
At right side of home page, you can see the national flag of different country for different
language selection. Just click the national flag you will get which language you want. You also
can see the orange color button with characters of update. Click “Update” button to update
your configuration software. Finished the update procedure, you will see the screen as shown
below. A message of “This is the newest version” displays on the screen now.
Please input user
name and password.
Login
Cancel
Language
selection
: English, Traditional Chinese, Simplified Chinese
This message
indicates there is new
version of
configuration software
for you. You can click
the “Update” button to
update your software.
Page 17
16
Update procedure
Home Page
After Login ZA1002US-5 user will see screen as above, and there are ten maincategories,
user can click on each category to extend detail items.
Home
Room
Device
Camera
Scene
Trigger
Schedule
SetZwave
Report
Please click on “OK” button to update the AVA-88 software.
Page 18
17
Help
The various configuration menus are explained below. You can select various function
listed in the first line of Home page display.
3.2 SetZwave-Z-Wave device settings
One of main functions of ZA1002US-5 is control and monitoring the room. If you would like to
implementation ofthese effortsrequirethe helpofZ-Wavedevicesin order tocomplete the task.
At first, you need to addthe newZ-Wavedevicesto ZA1002US-5forcontroland monitoringthe
room or remove the Z-wave device whichnotused.
3.2.1 The Z-Wave device configuration
3.2.1.1 Add a Z-Wave device
You can add the Z-Wave device by clicking on the category of “SetZwave” in the menu bar.
The procedure of adding the Z-wave device is described as follows.
Step 1: Enter the "SetZwave" page and select "DeviceConfiguration"
SetZwave－Device Configuration
Step 2: Click on the "Include NewDevice", the screen will appear"Add Device: Waiting
for a user action."
Step 1a: Click on “SetZwave”
category of main
menu.
Step 1b: Click on “Device Configuration” item.
Step 2: Click on “Include New Device” button.
Page 19
18
Step 3: Press the programming switch button on the Z-Wave device for connection. The
location of programming switch button depends on the type of Z-Wave device
that you use. Please refer to the user manual of the Z-Wave device.
p.s. You also canbuy these Z-Wave devices such as Plug-in on/off module, Door sensor,
PIR sensor, Wireless siren…etc. from Avadesign Technology.
Step 4:When your Z-Wave device has added successfully, the message of "Add Device:
Command has completed successfully"will display on the screen.
Step 5:When the new Z-Wave device was found,you can modify the name and room
settingsas shown below.
Step 3: Press the programming switch button on the Z-wave device.
The Z-wave device was added successfully.
Plug-in on/off module
Page 20
19
Step 6: Then click "device", the new Z-wave device is ready to use now.
3.2.1.2 Remove a Z-Wave device
You also can remove the Z-Wave device by clicking on the category of “SetZwave” in the
menu bar. The procedure of removing the Z-wave device is described as follows.
Step 1: Enter the "SetZwave" page and select "DeviceConfiguration"
SetZwave－Device Configuration
Step 2: Click on the "Exclude Device", the screen will appear "RemoveDevice: Waiting
for a user action."
Step 1b: Click on “Device Configuration” item.
Step 2: Click on “Exclude Device” button.
Step 1a: Click on “SetZwave”
category of main menu.
Page 21
20
Step 3:Press the programming switch button on the Z-Wave device forremoving. The
location of programming switch button depends on the type of Z-Wave device
that you use. Please refer to the user manual of the Z-Wave device.
Step 4: When your Z-Wave device has removed successfully, the message of "Remove
Device: Command has completed successfully"will display on the screen.
Step 3: Press the programming switch button
on the Z-wave device.
The Z-wave device was removed successfully.
Plug-in on/off module
Page 22
21
3.2.2 Z-Wave Control and Log
ZA1002US-5provides alarm records of all Z-Wave control devices for user as follows.
SetZwave－ZwaveControl& Log
When you click on “Update” button, you will see the listing of software version updated.
Clicking on the “Version” button at the end of screen, the system will check the software
version of ZA1002US-5 for you automatically.
Click on “Version” button
to check the version.
You can click the
“Update” button to
download the newest
version for updating.
You also can click the “reset”
button to reset the system.
Page 23
22
You also can click the “reset” button to reset the system shown as above diagram. Then you
can click on “OK” button to reset the system or “Cancel” button to quit the reset process.
3.2.3 Topology
The topology diagram shows the connection relationship of ZA1002US-5 and all of Z-wave
devices. The small square at row 1 and column 1 represents the ZA1002US-5. The small
square at row 1 and column 2 represents a Z-Wave device. Applying the topology diagram,
user can decide the control path of ZA1002US-5 and each Z-Wave device. For example,
theZA1002US-5can control the remote device B indirectly by device A.
SetZwave－Topology
B A
Page 24
23
3.2.4 Door Lock Security
You can select a door lock to add password or modify password.
SetZwave－Door Lock Security
Then you will see the listing of user name and password. Clicking on the pen icon to modify
the password. You also can click on the Xsymbol todelete the password.
You can click on the “Add” button to add new password as below. The maximum length of
password is 10 digits and you can input numeric 0 ~ 9.
Select a door lock to add or modify password.
Page 25
24
You can click on the “Log” button to get the door lock records as below. The maximum
number of logs is 5. Please input the record number that equal or less than 5 then click on
“Search” button.
The “Time” button on the right side of screen is used for time setting by manually. You have to
input the right date and time by yourself. When you replace the battery of Electric Deadbolt,
please remember to modify the date and time here.
3.2.5 Version Information
Clicking on “Version Information” item, you will get the information of software version.
SetZwave－Version Information
Page 26
25
3.3 Room setting
ZA1002US-5 can classify and integrate all kinds of Z-Wave devices to do home automation
includes room, scene, trigger, schedule and report.
3.3.1 Create room
Create rooms to distribute Z-Wave devices
According to the different room in the family, you can distribute the Z-Wave devices to each
room. And you can learnwhichroomwas invadedor controlledhousehold appliances quickly.
Now, you can create a new room by clicking on “Create Room” item. Then input the room
name and click on “Add” button.
Room－Create Room
You also can change the icon of the room by clicking on “Change ICON” button. Then you will
see some pictures that you can choose for the proper room as below screen.
Please input the room name. Then click on “Add” button to create a
new room.
Page 27
26
If you change icon and input “meeting room” in the field of room name, and click on “Add”
button.
Then you will see the meeting room appear on the left side of screen.
Kitchen
Study room
Bathroom
Bedroom
Living room
or
Meeting room
Dining room
Hallway
Congratulation! You have created a meeting room
successfully.
Page 28
27
3.3.2 All rooms
You can see the device status in each room easily by clicking on “All rooms” item.
3.4 Device setting
You can place the Z-wave device in the right room by selecting device function in the top
menu and choosing a device which you want.
For example, you create a meeting room at section 3.3, and you would like to place light
device in this room. The setting procedure is described as following:
Step 1: Select “Device” function and clicking on “All Devices” item to show all of the
Z-Wave devices on the screen.
Step 2: Choose the device that you need and click on the icon of pen to edit the content
of device.For example, you place light device in this room.
Please refer to the following screen.
Page 29
28
Device－All Devices
Step 2: Edit
Step 1
Page 30
29
Step 3: Edit the content of light device. Please input the device name and room name.
Then click on “Save” button to save the configuration. You also can check this
node by clicking on “Check and Remove” button and the message of “The node
is OK” displays on the screen.
Step 4: Go back to “Room” functionand click on “Meeting room” item, then you will see
the light device
Room－Meeting room
Now, you can place another device to other room continuously. For example, you want
to place electronic deadbolt in hallway. Please refer to the following screens.
Page 31
30
Then you will find the electronic deadbolt in hallway now.
Page 32
31
3.5 Scene Setting-Control Z-Wave devices
You cancontrol and combine a number ofZ-Wavedevicestogether andexecute a designed
operation actionbyclicking onekey only.
3.5.1 Create Scene
Step 1:Select "Scene" function in the top menu on the screen. Then click on “Create Scene”
item. Please input the scene name and click on “Add” button.
Scene－Create Scene
Step 2:Now, you can see the scene was created and named as “Turn on the light for meeting
room”. You also can edit the scene name by clicking on the icon of pen.
You also can edit the scene
name by clicking on the icon of
pen.
Page 33
32
Then add controlled Z-Wave devices in this scenario that shown as below. For
example: you add a switchof light in this scenario.
You can add more controlled Z-Wave devices in this scenario by selecting one device
in the scrolling menu and clicking on the icon of plus sign on the screen. Then you will
see a new controlled device display on the screen now.
You also can delete a controlled Z-Wave device in this scenario by clicking on the
icon of “X”. Then you will see this controlled device disappear on the screen now.
Step 3:Setting the proper action for each device.For example: you can turn on the light by
clicking on “On” button. Then you will see the color of light has changed to bright
yellow.
Delete a controlled Z-Wave device
in this scenario by clicking on the
icon of “X”.
Scrolling menu
Add a new device
Page 34
33
Step 4:You can click on “Run” button of the scene that has set by yourself. The
correspondingZ-Wavedevice will be used.
Loading...