Page 1
1
TC2-HDBT_manual_en
TECHCONNECT HDBT
OWNERS MANUAL
www.visionaudiovisual.com/techconnect/tc2-hdbt
Page 2
2
TC2-HDBT_manual_en
DECLARATION OF CONFORMITY
Where applicable Vision products ar e certified and comply with all known local regulations to a
‘CB Certification’ standard. Vision commits to ensure all products are fully compliant with all
applicable certification standards for sale in the EU and other participating countries.
The product described in this owner manual is in compliance with RoHS (E U directive
2002/95/EC), and WEEE (EU directive 2002/96/EC) standards. This product should be r e tur ned
to the place of purchase at the end of its useful life for recycling.
WARNINGS
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR
BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the
user to the presence of u n in su lat ed “ dangerous voltage” within the product’s enclosure that may be
of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point w it h in an equilateral trian gle, is intended to alert t h e u ser t o the presence of
important operating and maintenance (servicing) instructions in the literature accompanying the
appliance.
WARNING: TO REDUCE THE R ISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE.
All products are designed and impor ted into the EU by ‘Vision’ who is wholly owned by ‘Azlan
Logistics Ltd.’, Registered in England Nr. 04625566 at Lion House, 4 Pioneer Business Park,
Clifton Moor, York, YO30 4GH. WEEE Registration: GD0046SY
DECLARATION OF ORIG I N
All Vision products are made in the People’s Republic of China (PRC).
Page 3
3
TC2-HDBT_manual_en
USE ONLY DOMESTIC AC OUTLETS
Connecting the unit to an outlet supplying a higher voltage may create a fire hazard.
HANDLE THE POWER CORD WITH CARE
Do not disconnect the plug from the AC outlet by pulling the cord; always pull the plug itself.
Pulling the cord may damage it. If you do not intend to us e your unit for any considerable
length of time, unplug the unit. Do not place furniture or other heavy objects on the cord, and
try to avoid dropping heavy objects on it. Do not tie a knot in the power cord. Not only could
the cord be damaged, but a short circuit could a lso be caused with a consequent fire hazard.
PLACE OF INSTALLATION
Avoid installing this product under the following conditions:
• Moist or humid places
• Places exposed to direct sunlight or close to heating equipment
• Extremely cold locations
• Places subject to excessive vibration or dust
• Poorly ventilated places
Do not expose this product to dripping or splashing. DO NOT PLACE OBJECTS FILLED WITH
LIQUIDS ON OR NEAR THIS PRODUCT!
MOVING THE UNIT
Before moving the unit, be sure to pull out the power cord from the AC outlet and disconnect
the interconnection cords with other units.
WARNING SIGNS
If you detect an abnormal smell or smoke, turn this product off immediately and unplug the
power cord. Contact your reseller or Vision.
PACKAGING
Save all packing material. It is ess e ntial for shipping in the event the unit ever needs repair.
IF ORIGINAL PACKAGING IS NOT USED TO RETURN THE UNIT TO THE SERVICE CENTRE,
DAMAGE IN TRANSIT WILL NOT BE COVERED BY WARRANTY.
OVERVIEW
This product combines HDMI and RS-232 signals and routes them through CAT5e (ethernet)
cable.
Page 4
4
TC2-HDBT_manual_en
TRANSMITTER
1. Mini USB-B connector - for firmware updates
2. Link LED – shows HDMI input is connected
3. HDMI Input
4. RS-232 Input
5. CAT5e/6 Output
6. Status LED – shows receiver is attached
7. 12V 3A Power input
8. Power LED
1 2 3 4 5 6 7
8
Page 5
5
TC2-HDBT_manual_en
RECEIVER
1. Mini USB-B connector - for firmware updates
2. 3.5mm Minijack Audio Output (analogue)
3. EDID selector
4. HDMI Output
5. RS-232 Output
6. CAT5e/6 Input
7. Status LED – shows transmitter is attached
8. 12V 3A Power input
9. Power LED
1 2 3 4 5 6 7 8 9
Page 6
6
TC2-HDBT_manual_en
INSTALLATION
When used as a set connect power to either the transmitter or receiver but
not both.
Vision HDBT products use proprietary PoE. When using either the
transmitter or receiver in conjunction with other manufacturer’s HDBT
equipment it is necessary to connect power.
1. CONNECT CABLES
You can use unshielded twisted pair (UTP) cable or shielded twisted pair (STP). For best
results use STP CAT5e/6 cable.
2. POWER ON HDBT TRANSMITTER AND RECEIVER
3. POWER ON DISPLAY DEVICE
4. POWER ON SOURCE DEVICE
EDID (EXTENDED DISPLAY IDENTIFICATION DATA)
This enables the source device to ‘ask’ the display device what resolu tion it is , a nd output that
resolution.
Position Functions
000 (default) Use EDID from display device, analogue audio output enabled
001 Use EDID from display device, audio output disabled
010 Fixed EDID, 3D, digital audio output enabled
011 Fixed EDID, Non-3D, digital audio output enabled
Page 7
7
TC2-HDBT_manual_en
TROUBLESHOOTING
If your system is not operating properly, ple ase refer to the following information. If the
problem persists, disconnect from power and contact your AV reseller immediately.
Problem
Correction
Status lights no on
• Check CAT5e/6 cable
• The cable should be wired to 568B standard at both ends.
If one end has green and orange swapped this is a crossover cable and cannot be used.
• Try unshielded cable
No Power light
• Check power connections
• Try alternative power supply
Link light not on
• Check HDMI cable between source and transmitter
No audio
• Check the EDID switches on receiver
Image displayed
incorrectly
• Check the EDID switches on receiver
• Repeat start-up sequence
Lights all on but no
image
• Check that source is turned on
Page 8
8
TC2-HDBT_manual_en
SPECIFICATIONS
TRANSMITTER DIMENSIONS: 105 x 88 x 25 mm (length x width x height)
RECEIVER DIMENSIONS: 108 x 10 6 x 25 mm
PRODUCT WEIGHT:
Set: 0.68 kg
Transmitter: 0.30 kg
Receiver: 0.38 kg
CONSTRUCTION MATERIA L : Me ta l
COLOUR: White
TECHNICAL DETAILS:
Signaling rates: 2.25Gbits x 3
Input Video Signal: 0.5-1.0 volts p-p
Input DDC Signal: 5 volts p-p (TTL)
Video(HDMI) format supported: DTV/HDTV:1080p/1080i/720p/576p/480p/576i/480i
HDMI Version: 1.4 (3D)
Output Audio: PCM 2.0
Operating temperature range: -5 to +35°C (-41 to +95 °F)
Operating humidity range: 5 to 90 % RH (no c ondensation)
Power Consumption: 15 Watts (max.)
INPUTS:
1 x HDMI (type A)
1 x RS-232 (Phoenix connector)
OUTPUTS:
1 x HDMI (type A)
1 x RS-232 (Phoenix connector)
1 x Analogue Audio (Minijack 3.5mm)
POWER SUPPLY: 100-240v 50/60Hz AC External Power Supply – integrated transformer/plug
type. DC Output 12V 3A, DC Cable 1.8m. Transformer dimensions: 96 x 44 x 28mm.
Interchangeable prongs including UK, EU, AU, US. Note: a normal figure-8 cable can be plugged
into the transformer if preferred.
COMPLIANCES: RoHS, WEEE, CE, and CB compliant.
ACCESSORIES
1 x Pair of mounting ears
Page 9
9
TC2-HDBT_manual_en
WARRANTY
This product comes with a 2-year return to base warranty, effective from the date of purchase.
This warranty applies only to the original purchaser and is not transferable. For the avoidance of
doubt, this will be taken from the information held by the appointed national distributor at the
point of sale. If the product is DOA (dead on arrival), you have 21 days from purchase date to
notify the national distributor via your AV reseller. The liability of the manufac tur e r and its
appointed service company is limited to the cost of repair and/or replacement of the faulty unit
under warranty, except for death or injury (EU85/374/EEC). This warranty protects you against
the following:
• Failure of any components, including the power supply.
• Damage when the product is first removed from its packaging if reported within 24 hours of
purchase.
If you find you do have a problem with this product, you should c ontact the AV reseller you
purchased this product from. The original purchaser is responsible for s hipment of the product
to the manufacturer’s appointed service centre for repair.
We will endeavour to return repaired units within 5 working days, however this may not always
be possible, in which case it will be returned as soon as practicably possible. In line with our
WEEE commitments, the manufacturer endeavour s to replace the faulty parts of the product
rather than replacing the whole unit. This warranty does not protect this product against faults
caused by abuse, misuse, incorrect installation, unstable or faulty p ower input, which might be
caused by ignoring the guidelines set out in this manual.
LEGAL DISCLAIMER: Because we are committed to improving our products, the details above
may change without prior warning. This User Manual is published without warranty and any
improvements or changes to the User Manual necessitated by typographical errors, inaccuracies
of current information, or improvements to programs and/or equipment, may be made a t any
time and without notice. Such changes will be incorporated into new editions of the U ser
Manual.
Loading...