Vision TF40, TF20, T40 Owner's Manual

TF40
TF20
T40

Read the TREADMILL GUIDE before using this OWNER’S MANUAL.

TREADMILL OWNER’S MANUAL

2 3

IMPORTANT PRECAUTIONS

SAVE THESE INSTRUCTIONS

When using an electrical product, basic precautions should always be followed, including the following: Read all instructions
before using this treadmill. It is the responsibility of the owner to ensure that all users of this treadmill are adequately informed of
all warnings and precautions. If you have any questions after reading this manual, contact your authorized Vision Fitness retailer.

This treadmill is intended for in-home use only. Do not use this treadmill in any commercial, rental, school or institutional setting.
Failure to comply will void the warranty.

This treadmill has a pre-waxed belt and should never be lubricated.
Waxing the belt can cause damage that is not covered by the warranty.

IMPORTANT

4 5

TO REDUCE THE RISK OF BURNS, FIRE , ELECTRICAL SHOC K OR INJURY TO PE RSONS:

• At NO time should children under the age of 13 or pets be within 310 cm (10 feet) of the treadmill.

• At NO time should children under the age of 13 use the treadmill.

• Children over the age of 13 or disabled persons should not use the treadmill without adult supervision.

• Use the treadmill only for its intended use as described in the TREADM ILL GUIDE and OWNER’S MANUAL.

• Do not use other attachments that are not recommended by the manufacturer. Attachments may cause injury.

• Never operate the treadmill if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or
immersed in water.

• Keep power cord away from heated surfaces. Do not carry this unit by its supply cord or use the cord as a handle.

• Never operate the treadmill with the air opening blocked. Keep the air opening clean, free of lint, hair and the like.

• To prevent electrical shock, never drop or insert any object into any opening.

• Do not operate where aerosol (spray) products are being used or when oxygen is being administered.

• To disconnect, turn all controls to the off position, then remove plug from outlet.

• Do not use treadmill in any location that is not temperature controlled, such as but not limited to garages, porches, pool rooms,
bathrooms, car ports or outdoors. Failure to comply may void the warranty.

• This treadmill is intended for in-home use only. Do not use this treadmill in any commercial, rental, school or institutional setting.
Failure to comply will void the warranty.

• Do not remove the console covers. Service should only be done by an authorized service technician.

It is essential that your treadmill is used only indoors, in a climate-controlled room. If your treadmill has been exposed to colder
temperatures or high-moisture climates, it is strongly recommended that the treadmill is warmed up to room temperature before
first time use. Failure to do so may cause premature electronic failure.

TO REDUCE THE RISK OF BURNS, FIRE , ELECTRICAL SHOC K OR INJURY TO PE RSONS:

• Never use the treadmill before securing the safety tether clip to your clothing.

• If you experience any kind of pain, including but not limited to chest pains, nausea, dizziness or shortness of breath, stop
exercising immediately and consult your physician before continuing.

• When exercising, always maintain a comfortable pace.

• Do not wear clothes that might catch on any part of the treadmill.

• Always wear athletic shoes while using this equipment.

• Do not jump on the treadmill.

• At no time should more than one person be on treadmill while in operation.

• This treadmill should not be used by persons weighing more than specified in the OWNE R’S MANUAL WARRANTY SECTION.
Failure to comply will void the warranty.

• When lowering the treadmill deck, wait until rear feet are firmly on the floor before stepping on the deck.

• Disconnect all power before servicing or moving the equipment. To clean, wipe surfaces down with soap and slightly damp cloth
only; never use solvents. (See MAINTENANCE)

• The treadmill should never be left unattended when plugged in. Unplug from outlet when not in use, and before putting on or
taking off parts.

• Do not operate under blanket or pillow. Excessive heating can occur and cause fire, electric shock or injury to persons.

• Connect this exercise product to a properly grounded outlet only.

• Do not tip the machine on its side at any time.

WARNING

TO REDUCE THE RISK OF ELECTRICAL SHOCK :

Always unplug the treadmill from the electrical outlet immediately after using, and before cleaning, performing maintenance and putting on or
taking off parts.

DANGER WARNING

6 7

ASSEMBLY

There are several areas during the assembly process when special attention must be paid. It is very important to follow the
assembly instructions correctly and to make sure all parts are firmly tightened. If the assembly instructions are not followed
correctly, the treadmill could have parts that are not tightened and will seem loose and may cause irritating noises. To prevent
damage to the treadmill, the assembly instructions must be reviewed and corrective actions should be taken.

Before proceeding, find your treadmill’s serial number located on a white barcode sticker
on the base frame as shown in this image.

ENTER YOUR SE RIAL NUMBE R AND MODEL NAME IN TH E BOXES BELOW:

SERIAL N UMBER:

MODEL NAM E: VISION TREADMILL

WARNING

SERIAL N UMBER LOCATION

GROUNDING INSTRUCTIONS

This product must be grounded. If a treadmill should malfunction or break down, grounding provides a path of least resistance
for electrical current to reduce the risk of electrical shock. This product is equipped with a cord having an equipment-grounding
conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in
accordance with local codes and ordinances.

Connect this exercise product to a properly grounded outlet only.

Never operate product with a damaged cord or plug even if it is working properly. Never operate any product if it appears
damaged, or has been immersed in water. Contact your authorized Vision Fitness retailer for replacement or repair.

WARNING

DANGER

Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified
electrician or serviceman if you are in doubt as to whether the product is properly grounded. Do not modify the plug provided
with the product. If it will not fit the outlet, have a proper outlet installed by a qualified electrician.

Make sure that the product is connected to an outlet having the same configuration as the plug. No adapter should be used with this
product.

This product must be used on a dedicated circuit. To determine if you are on a dedicated circuit, shut off the power to that circuit
and observe if any other devices lose power. If so, move devices to a different circuit. Note: There are usually multiple outlets on one
circuit. This treadmill should be used with a minimum 20-amp circuit.

8 9

WATER B OTTLE H OLDER

GRIP PULSE BARS

QUIC K KEY ( TF40 ON LY)

CONS OLE (TO UCH CON SOLE S HOWN)

TRAN SPORT WHEEL

ON/O FF SWI TCH

CIRC UIT BRE AKER

POWE R CORD

READ ING R ACK / TAB LET HOL DER

HAND LEBARS

USB P ORT AN D IPOD® CORD ( TOUCH C ONSOL E ONLY)

SAFE TY KEY PLACE MENT

MOTOR COVER

WHEE L LOCK

SIDE RAIL

ROLLE R END C AP

REAR ROLLE R TENSI ON
AND A DJUSTM ENT BO LTS

CONS OLE MAS T

IN RE ACH CO NTROLS

BASE FRAME COVER ( TF40 O NLY)

RUNN ING BE LT / RUNN ING DE CK

SUPP ORT BAR

1

2

ABOVE FOOT L ATCH

1

2

FOOT L OCK LATC H (UN DERNE ATH DEC K)

WATER B OTTLE H OLDER

GRIP PULSE BARS

CONS OLE (TO UCH CON SOLE S HOWN)

TRAN SPORT WHEEL

ON/O FF SWI TCH

CIRC UIT BRE AKER

POWE R CORD

READ ING R ACK / TAB LET HOL DER

HAND LEBARS

USB P ORT AN D IPOD C ORD (T OUCH CO NSOLE ONLY)

SAFE TY KEY PLACE MENT

MOTOR COVER

SIDE RAIL

ROLLE R END C AP

REAR ROLLE R TENSI ON
AND A DJUSTM ENT BO LTS

CONS OLE MAS T

IN RE ACH CO NTROLS

RUNN ING BE LT / RUNN ING DE CK

SUPP ORT BAR

QUIC K KEY

TF20
TF40

T40

10 11

TOOLS INCLUDE D:

F 5 mm T-Wrench
F 13 mm Hex Wrench
F 4 mm L-Wrench
F 5 mm L-Wrench
F 6 mm T-Wrench
F 8 mm T Wrench
F Screwdriver

PARTS INCLUDED :

F 2 Console Masts
F 2 Handlebars
F 2 Support Bars
F 2 Support Bar Caps (T4 0)
F 2 Sets Base Frame Covers
F 1 Console Base
F 1 Console Base Cover
F 1 Water Bottle Holder
F 1 Accessory Holder
F 1 Hardware Kit
F 1 Safety Key
F 1 Power Cord

DO NOT ATTEMPT TO LIFT TH E TREADMILL! Do not move or lift treadmill
from packaging until specified to do so in the assembly instructions. You may
remove the plastic wrap from console masts.

WARNING

UNPACKING

Place the treadmill carton on a level flat surface. It is recommended that you place a
protective covering on your floor. Take CAUTION when handling and transporting this
unit. Once the banding straps have been removed, do not transport this unit unless it is
fully assembled. Unpack and assemble the unit where it will be used. Never grab hold of
any portion of the incline frame and attempt to lift or move the treadmill. Lift the treadmill
from the roller end caps area while a second person removes the parts packed under
the treadmill.

FAILURE TO FOLLOW THESE I NSTRUCTIONS COULD RESULT IN INJURY!

WARNING

NOTE: During each assembly step, ensure that ALL nuts and bolts are in place and
partially threaded in before completely tightening any ONE bolt.

NOTE: A light application of grease may aid in the installation of hardware. Any grease,
such as lithium bike grease, is recommended.

PRE-ASSEMBLY

ALL

MODELS

If you have questions or if there
are any missing parts, contact
your authorized Vision Fitness
retailer.

NEED HELP?

BOLT (A)
20 mm
Qty: 6

SPRING WASHE R (B)

8.2 mm
Qty: 6

ARC WASHER (C)

8.4 mm
Qty: 6

T40 HARDWARE FOR STEP 1 :

BOLTS (A)

SPRING WASHER S (B)

LEFT CONSOLE MAST

LEAD WIRE

CONSOLE CABLE

ARC WASHERS (C)

BASE FRAME

RIGHT CONSOLE MAST

T40 ASSEMBLY STEP 1

NOTE: This step is for T40 models only.

A Open hardware for step 1.

B Attach lead wire to console cable and pull

lead wire through rig ht console mast. After
pulling the lead wire through the mast, the top of
the console cable should be located at the top
of the mast. Detach and discard lead wire.

N

C Attach console mast to base frame using 3

bolts (a), 3 spring washe rs (b) and 3 arc
washers (c).

D Repeat step C on other side.

NOTE: Do not tighten bolts until step 4 is complete.

NOTE: Do not pinch console cable when placing
the mast onto the base frame.

T40

ONLY

T40 ONLY

12 13

TF20

ONLY

TF40

ONLY

BOLT (A)
20 mm
Qty: 6

SPRING
WASHER (B)

8.2 mm
Qty: 6

ARC
WASHER (C)

8.4 mm
Qty: 6

SCREW (M)
20 mm
Qty: 2

SCREW (N)
12 mm
Qty: 4

BOLTS (A)

SPRING WASHER S (B)

LEFT CONSOLE MAST

LEAD WIRE

CONSOLE CABLE

SCREWS (N)

ARC WASHERS (C)

BASE FRAME

SCREW (M)

BASE FRAME COVER

RIGHT CONSOLE MAST

TF40 ASSEMBLY STEP 1

NOTE: This step is for TF40 models only.

A Open hardware for step 1.

B Slide base frame covers over bas e frame.

Attach base frame cove rs using 2 screws
(m) and 4 screws (n).

C Attach lead wire to console cable and pull

lead wire through rig ht console mast. After
pulling the lead wire through the mast, the top of
the console cable should be located at the top
of the mast. Detach and discard lead wire.

D Attach console mast to base frame using 3

bolts (a), 3 spring washe rs (b) and 3 arc
washers (c).

E Repeat step C on other side.

NOTE: Do not tighten bolts until step 4 is complete.

NOTE: Do not pinch console cable when placing
the mast onto the base frame.

TF40 ONLY

TF40 HARDWARE FOR STEP 1 :

BOLT (A)
20 mm
Qty: 6

SPRING
WASHER (B)

8.2 mm
Qty: 6

ARC
WASHER (C)

8.4 mm
Qty: 6

BOLTS (A)

SPRING WASHER S (B)

LEFT CONSOLE MAST

LEAD WIRE

CONSOLE CABLE

ARC WASHERS (C)

BASE FRAME

BASE FRAME COVER

RIGHT CONSOLE MAST

TF20 ASSEMBLY STEP 1

TF20 ONLY

TF20 HARDWARE FOR STEP 1 :

NOTE: This step is for TF20 models only.

A Open hardware for step 1.

B Slide base frame cover up r ight console

mast. Attach lead wire to con sole cable
and pull lead wire through rig ht console
mast. After pulling the lead wire through the
mast, the top of the console cable should be
located at the top of the mast. Detach and discard
lead wire.

NOTE: Do not pinch console cable when placing the
mast onto the base frame.

C Place right console mast over base frame.

D Attach console mast to main frame

bracket using 3 bolts (a), 3 spring
washers (b) and 3 arc was hers (c).

NOTE: Do not tighten bolts until step 4 is complete.

E Slide base fram e cover up left console

mast. Repeat STEP D to attach left console
mast.

F Slide bas e frame covers down.

14 15

T40

ONLY

T40 ASSEMBLY STEP 3

BOLT (A)

SPRING WASHE R (B)

BOLT (F)

HANDLEBAR

SUPPORT BAR

BASE FRAME

ARC WASHER (E)

SPRING WASHE R (B)

ARC WASHER (E)

T40 HARDWARE FOR STEP 3 :

NOTE: This step is for T40 models only.

A Open hardware for step 3.

B Attach the right support bar to the bas e

frame using 1 arc washe r (e), 1 spring
washer (b) and 1 bolt (f).

NOTE: Do not tighten bolts until step 4 is complete.

C

Attach the right support bar to the

handlebar using 1 arc washe r (e), 1
spri ng washer (b) and 1 bolt (a).

D Repeat on other side.

BOLT (A)
20 mm
Qty: 2

SPRING
WASHER (B)

8.2 mm
Qty: 4

ARC
WASHER (E)

8.4 mm
Qty: 4

BOLT (F)
95 mm
Qty: 2

ASSEMBLY STEP 2

BOLT (A)
20 mm
Qty: 6

SPRING
WASHER (B)

8.2 mm
Qty: 6

ARC
WASHER (C)

8.4 mm
Qty: 4

FLAT
WASHER (D)

8.2 mm
Qty: 2

HARDWARE FOR STEP 2 :

FLAT WASHER (D)

SPRING WASHE R (B)

ARC WASHERS (C)

BOLT (A)

RIGHT HANDLE BAR

CONSOLE CABLES

RIGHT CONSOLE MAST

A Open hardware for step 2.

B Guide console cables from handlebars

through and out of the tops of the console
masts.

C Slide handlebars onto console masts.

D Attach right handlebar to right console

mast using 1 flat washer (d), 1 spr ing
washer (b) and 1 bolt (a) from the inside and

2 arc washers (c), 2 s pring washers (b)
and 2 bolts (a) from below.

E

Repeat on other side.

NOTE: Do not pinch console cables while
attaching the handlebars.

T40 SHOWN

ALL

MODELS

T40 ONLY

NOTE: Do not tighten bolts until step 4 is complete.

16 17

TF40

ONLY

TF20

ONLY

TF40 ASSEMBLY STEP 3

FLAT WASHERS (H)

SPRING WASHER S (J)

ARC WASHERS (E)

SPRING WASHER S (B)

BASE FRAME

SUPPORT BAR

BOLTS (L)

HANDLEBAR

BOLT (A)

TF40 HARDWARE FOR STEP 3 :

NOTE: This step is for TF40 models only.

A Open hardware for step 3.

B Attach the bottom of the support bar to the

base frame using 2 flat washe rs (h), 2
spri ng washer s (J) and 2 bolts (l).

C Attach the top of the support bar to the

handlebar using 1 arc washe r (e), 1
spri ng washer (b) and 1 bolt (a).

D Repeat on other side.

BOLT (A)
20 mm
Qty: 2

SPRING
WASHER (B)

8.2 mm
Qty: 2

ARC
WASHER (E)

8.4 mm
Qty: 2

BOLT (L)
20 mm
Qty: 4

SPRING
WASHER (J)
6 mm
Qty: 4

FLAT
WASHER (H)
6 mm
Qty: 4

TF20 ASSEMBLY STEP 3

FLAT WASHERS (H)

SPRING WASHER S (J)

ARC WASHERS (E)

SPRING WASHER S (B)

BASE FRAME

SUPPORT BAR

BOLTS (L)

HANDLEBAR

BOLT (A)

TF20 HARDWARE FOR STEP 3 :

NOTE: This step is for TF20 models only.

A Open hardware for step 3.

B Attach the bottom of the support bar to the

base frame using 2 flat washe rs (h), 2
spri ng washer s (J) and 2 bolts (l).

C Attach the top of the support bar to the

handlebar using 1 arc washe r (e), 1
spri ng washer (b) and 1 bolt (a).

D Repeat on other side.

BOLT (A)
20 mm
Qty: 2

SPRING
WASHER (B)

8.2 mm
Qty: 2

ARC
WASHER (E)
8,4 mm
Qty: 2

BOLT (L)
20 mm
Qty: 4

SPRING
WASHER (J)
6 mm
Qty: 4

FLAT
WASHER (H)
6 mm
Qty: 4

TF40 ONLY TF20 ONLY

NOTE: Do not tighten bolts until step 4 is complete. NOTE: Do not tighten bolts until step 4 is complete.

18 19

TF40

ONLY

T40 ASSEMBLY STEP 4

T40

ONLY

BOLT (A)
20 mm
Qty: 6

SCREW (G)
12 mm
Qty: 6

SPRING
WASHER (B)

8.2 mm
Qty: 6

ARC
WASHER (E)

8.4 mm
Qty: 6

HARDWARE FOR STEP 4 :

ARC WASHERS (D)

SPRING WASHER S (B)

SCREWS (G)

MAST
COVERS

CONSOLE
MAST

BASE FRAME

BOLTS (A)

CONSOLE BASE

CONSOLE CABLES

NOTE: This step is for T40 models only.

A Open hardware for step 4.

B Gently place console base on top of

console masts.

C Connect the console cables and tuck

them inside the console masts and slide
console base into con sole masts.

D Connect the console base to console

masts using 6 arc washers (e), 6
spri ng washer s (b) and 6 bolts (a).

E Attach mast covers to bas e frame

using 3 screws (g).

F Repeat on other side.

NOTE: Be careful not to pinch the console
cables while attaching the console base.

NOTE: Tighten all bolts from STEPS 1–3.

BOLT (A)
20 mm
Qty: 6

SPRING
WASHER (B)

8.2 mm
Qty: 6

ARC
WASHER (E)

8.4 mm
Qty: 6

SCREW (N)
12 mm
Qty: 4

TF40 ASSEMBLY STEP 4

HARDWARE FOR STEP 4 :

ARC WASHERS (D)

SPRING WASHERS (B)

BOLTS (A)

CONSOLE BASE

CONSOLE CABLES

CONSOLE MAST

BASE FRAME COVER

SCREWS (N)

BASE FRAME

NOTE: This step is for TF40 models only.

A Open hardware for step 4.

B Gently place console base on top of

console masts.

NOTE: Be careful not to pinch the console
cables while attaching the console base.

C

Connect the console cables and tuck
them inside the console masts and slide
console base into con sole masts.

D Connect the console base to console

masts using 6 arc washers (e), 6
spri ng washer s (b) and 6 bolts (a).

NOTE: Tighten all bolts from STEPS 1–3.

E

Attach the base frame cove rs to the
base frame using 4 scr ews (n).

T40 ONLY TF40 ONLY

20 21

ALL

MODELS

FLAT WASHERS (H)

BOLT (I)

PRE-INSTALLED
SCREWS

CONSOLE CABLES

CONSOLE REAR COVER

SPRING WASHER (J)

FLAT WASHERS (H)

SUPPORT BAR CAP

SUPPORT BAR

NUT (K)

CONSOLE BASE

CONSOLE

ASSEMBLY STEP 5

FLAT WASHERS (H)

BOLT (I)

PRE-INSTALLED
SCREWS

CONSOLE CABLES

CONSOLE REAR COVER

SPRING WASHER (J)

FLAT WASHERS (H)

NUT (K)

CONSOLE BASE

CONSOLE

HARDWARE FOR STEP 5 :

A Open hardware for step 5.

B Remove 2 pre-installed screws to

remove console rear cover from the
console.

C Attach the console to the console base

using 2 bolts (i) and 2 flat washers

(h) from above and 2 flat washers (h) 2
spri ng washer s (J) and 2 nuts (k) from

below.

D Connect the console cables to the

console.

E Re-attach the console rear c over to

the console using 2 pre-i nstalled
screws.

F T40 O NLY: Insert support bar caps into

bottom of support bar s.

BOLT (I)
45 mm
Qty: 2

NUT (K)
Qty: 2

SPRING
WASHER (J)
8 mm
Qty: 2

FLAT
WASHER (H)
8 mm
Qty: 4

NOTE: Be careful not to pinch the console
cables while attaching the console.

T40 ONLY:

TF20

ONLY

BOLT (A)
20 mm
Qty: 6

SCREW (M)
20 mm
Qty: 4

SPRING
WASHER (B)

8.2 mm
Qty: 6

ARC
WASHER (E)

8.4 mm
Qty: 6

TF20 ASSEMBLY STEP 4

HARDWARE FOR STEP 4 :

BASE FRAME

SCREWS (M)

BASE FRAME COVER

ARC WASHERS (D)

SPRING WASHERS (B)

BOLTS (A)

CONSOLE BASE

CONSOLE CABLES

CONSOLE MAST

NOTE: This step is for TF20 models only.

A Open hardware for step 4.

B Gently place console base on top of

console masts.

NOTE: Be careful not to pinch the console
cables while attaching the console base.

C

Connect the console cables and tuck
them inside the console masts and slide
console base into con sole masts.

D Connect the console base to console

masts using 6 arc washers (e), 6
spri ng washer s (b) and 6 bolts (a).

NOTE: Tighten all bolts from STEPS 1–3.

E

Attach base frame cove rs to base
frame using 4 screws (m).

TF20 ONLY

22 23

LIMITED HOME-USE WARRANTY

WEIGHT CAPACITY

T40 = 400 lbs (182 kilograms)
TF40 = 400 lbs (182 kilograms)
TF20 = 375 lbs (170 kilograms)

FRAME

Warranty on the frame against defects in workmanship and
materials for the period specified on the warranty policy from the
date of original purchase, so long as the device remains in the
possession of the original owner. (The frame is defined as the
welded metal base of the unit and does not included any parts
that can be removed.)

DRIVE MOTOR/ ELEVATI ON MOTOR

Warranty on the drive/elevation motors against defects in
workmanship and materials for the period specified on the
warranty policy from the date of original purchase, so long as the
device remains in the possession of the original owner. Labor or
installation of motor is not covered under the motor warranty.

ELECTRONICS & PARTS
Warranty on the electronic components, finish and
all original parts for the period specified on the
warranty policy from the date of original purchase,
so long as the device remains in the possession of
the original owner.

LABOR
Warranty shall cover the labor cost for the repair of
the device for the period specified on the warranty
policy from the date of the original purchase, so
long as the device remains in the possession of the
original owner.

NOTE: For further information on the warranty period, please
refer to the warranty policy along with the equipment.

BOLT (L)
20 mm
Qty: 4

BOLT (M)
20 mm
Qty: 6

ASSEMBLY STEP 6

HARDWARE FOR STEP 6 :

CONSOLE BASE

BOLTS (L)

CONSOLE BASE COVER

HANDLEBAR

BOLTS (M)

WATER BOTTLE HOLDER

A Open hardware for step 6.

B Attach the console base cover to the

console base using 4 bolts (l).

C Attach wate r bottle holder and

accessory holder to left and right
handlebars using 6 bolts (m).

ASSEMBLY COMPLETE!

This treadmill has a pre-waxed belt and
should never be lubricated. Waxing
the belt can cause damage that is not
covered by the warranty.

IMPORTANT

ALL

MODELS

24 25

EXCLUSIONS AND LIMITATIONS

Who IS covered:

• The original owner and is not transferable.

What IS covered:

• Repair or replacement of a defective motor, electronic component,
or defective part and is the sole remedy of the warranty.

What IS NOT covered:

• Normal wear and tear, improper assembly or maintenance, or
installation of parts or accessories not originally intended or
compatible with the equipment as sold.

• Damage or failure due to accident, abuse, corrosion, discoloration
of paint or plastic, neglect, theft, vandalism, fire, flood, wind,
lightning, freezing, or other natural disasters of any kind, power
reduction, fluctuation or failure from whatever cause, unusual
atmospheric conditions, collision, introduction of foreign objects
into the covered unit, or modifications that are unauthorized or not
recommended by the manufacturer.

• Incidental or consequential damages. The manufacturer is not
responsible or liable for indirect, special or consequential damages,
economic loss, loss of property, or profits, loss of enjoyment or
use, or other consequential damages of whatsoever nature in
connection with the purchase, use, repair or maintenance of the
equipment. The manufacturer does not provide monetary or other
compensation for any such repairs or replacement parts costs,
including but not limited to gym membership fees, work time lost,
diagnostic visits, maintenance visits or transportation.

• Equipment used for commercial purposes or any use other than a
single family or Household, unless endorsed by the manufacturer
for coverage.

SERVICE AND REPAIRS

• Delivery, assembly, installation, setup for original or
replacement units or labor or other costs associated with
removal or replacement of the covered unit.

• Any attempt to repair this equipment creates a risk of injury.
The manufacturer is not responsible or liable for any damage,
loss or liability arising from any personal injury incurred during
the course of, or as a result of any repair or attempted repair
of your fitness equipment by other than an authorized service
technician. All repairs attempted by you on your fitness
equipment are undertaken AT YOUR OWN RISK and the
manufacturer shall have no liability for any injury to the person
or property arising from such repairs.

• The warranty is limited to replacing or repairing, at the
servicer’s and/or manufacturer’s option, the same or
comparable model.

• Replacement units, parts and electronic components
reconditioned to as-new condition by the manufacturer or its
vendors may sometimes be supplied as warranty replacement
and constitute fulfillment of warranty terms.

TREADMILL OPERATION

See TREADMI LL GUIDE for instructions on the following:

• LO CATION OF THE TREADMI LL

• US ING THE SAFETY KE Y

• FO LDING THE TREADM ILL

• M OVING THE TREADMI LL

• LE VELING THE TREAD MILL

• TENSION ING THE RUNNING BE LT

• C ENTERING THE RUN NING BELT

• US ING THE HEART RATE FU NCTION

See CONSOLE MAN UAL for instructions on the following:

• CO NSOLE OPERATION

• CO NSOLE DISPLAY INFORM ATION

• PR OGRAM INFORMATION

• N IKE + IPOD OPERATION

• PAS SPORT PLAYER INFORM ATION

Vision Treadmills Owner's Manual 082812' | © 2012 Vision Fitness

www.visionfitness.com