Page 1
1
SP-2000P_manual_en
SP-2000P SOUNDBAR LOUDSPEAKER
OWNERS MANUAL
www.visionaudiovisual.com/techaudio/sp-2000p
Page 2
2
SP-2000P_manual_en
DECLARATION OF CONFORMITY
Where applicable Vision products ar e certified and comply with all known loc al regulations to a
‘CB Certification’ standard. Vision commits to ensure all products are fully compliant with all
applicable certification standards for sale in the EU and other participating countries.
The product described in this owner manual is in compliance with RoHS (EU directive
2002/95/EC), and WEEE (EU directive 2002/96/EC) standards. This product should be returned
to the place of purchase at the end of its useful life for recycling.
WARNINGS
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR
BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the
user to the presence of u n insulated “dangerous voltage” within the product’s enclosure that may be
of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point w it h in an equilateral trian gle, is intended to alert the user to the presence of
important operating and maintenance (servicing) instructions in the literature accompanying the
appliance.
WARNING: TO REDUCE THE R ISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE.
All products are designed and imported into the EU by ‘Vision’ who is wholly owned by ‘Azlan
Logistics Ltd.’, Registered in England Nr. 04625566 at Lion House, 4 Pioneer Business Park,
Clifton Moor, York, YO30 4GH. WEEE Registration: GD0046SY
DECLARATION OF ORIG I N
All Vision products are made in the People’s Republic of China (PRC).
Page 3
3
SP-2000P_manual_en
USE ONLY DOMESTIC AC OUTLETS
Connecting the unit to an outlet supplying a higher voltage may create a fire hazard.
HANDLE THE POWER CORD WITH CARE
Do not disconnect the plug from the AC outlet by pulling the cord; always pull the plug itself.
Pulling the cord may damage it. If you do not intend to us e your unit for any considerable
length of time, unplug the unit. Do not place furnit ure or other heavy objects on the cord, and
try to avoid dropping heavy objects on it. Do not tie a knot in the power cord. Not only could
the cord be damaged, but a short circuit could a lso be caused with a consequent fire hazard.
PLACE OF INSTALLATION
Avoid installing this product under the following conditions:
• Moist or humid places
• Places exposed to direct sunlight or close to heating equipment
• Extremely cold locations
• Places subject to excessive vibration or dust
• Poorly ventilated places
Do not expose this product to dripping or splashing. DO NOT PLACE OBJECTS FILLED WITH
LIQUIDS ON OR NEAR THIS PRODUCT!
MOVING THE UNIT
Before moving the unit, be sure to pull out the power cord from the AC outlet and disconnect
the interconnection cords with other units.
WARNING SIGNS
If you detect an abnormal smell or smoke, turn this product off immediately and unplug the
power cord. Contact your reseller or Vision.
PACKAGING
Save all packing material. It is ess e ntial for shipping in the event the unit ever needs repair.
IF ORIGINAL PACKAGING IS NOT USED TO RETURN THE UNIT TO THE SERVICE CENTRE,
DAMAGE IN TRANSIT WILL NOT BE COVERED BY WARRANTY.
WATTS
The most consistent standards for measuring watts are “Program Power” and “RMS” because
these measure average sustained levels.
Where loudspeakers have integrated amplifiers, then load (resis ta nce, measured in ohms) is
known so the wattage rating is fixed.
Page 4
4
SP-2000P_manual_en
REAR PANEL
UNDERSIDE
#
REMOTE CONTROL
1. Power
2. Input Select
3. Volume
4. Mute
5. Tone Control
Volume Dial
Long push to turn on/off
Short push to switch input
Power Input
1 2 3 4 5
Input 1 (2-phono)
Input 2 (3.5mm minijack)
Input 2 (3.5mm minijack)
Page 5
5
SP-2000P_manual_en
INSTALLATION
1. FIT BRACKETS TO SOUNDBAR Measure width of flat-panel mounting holes and fit the
brackets to the soundbar at same width.
2. PUT FLAT-PANEL ON TABLE SURFACE FACE-DOWN
3. LAY SP-2000P ASSEMBLY ON TOP OF FLAT-PANEL Position the slots in the brackets over
the flat-panel mounting holes.
4. FIX WALL OR FLOOR STAND BRACKET TO REAR OF FLAT-PANEL. The SP-2000P brackets
will be sandwiched between the flat -pa nel a nd the mount.
5. FIT FLAT-PANEL ASSEMBLY TO STAND OR WALL MOUNT. Then route power and input
cables to loudspeaker.
OPERATION
1. TURN ON AND OFF Long press on volume dial
2. CHANGE INPUT Short press on volume dial
NOTE: When power is turned on the last volume setting and input will resume.
Page 6
6
SP-2000P_manual_en
SPECIFICATIONS
PRODUCT DIMENSIONS: 1000 x 85 x 850 mm (length x width x height)
PRODUCT WEIGHT: 4.1 kg
CONSTRUCTION MATERIAL: MDF
COLOUR: Black
TECHNICAL DETAILS:
Amplifier Output: 2 x 15w watts (RMS)
Woofer: 4 x 2″
Tweeter: 2 x 1″
Input Terminals: 2 x Minijack, 1 x 2 Phono
Output Impedance: 4 ohms
Sensitivity: 88dB (1w/1m)
Frequency response: 150Hz-20kHz
POWER SUPPLY: 100-240v 50/60Hz AC External Power Supply – 12 volt / 3 amp.
Laptop-style transformer. Includes 4 x 0.5m figure-8 power cables: UK/EU/US/AU. DC tail
length: 4m.
COMPLIANCE: RoHS, WEEE, CE/EMC, C-TICK, FCC
ACCESSORIES:
2 x Wall brackets
1 x Remote Control (Battery included: CR2025 3V Li-Mn)
Page 7
7
SP-2000P_manual_en
WARRANTY
This product comes with a 2-year return to base warranty, effective from the date of purchase.
This warranty applies only to the original purchaser and is not transferable. For the avoid ance of
doubt, this will be taken from the information held by the appointed national distributor at the
point of sale. If the product is DOA (dead on arrival), you have 21 days from purchase date to
notify the national distributor via your AV reseller. The liability of the manufacturer and its
appointed service company is limited to the cost of repair and/or replacement of the faulty unit
under warranty, except for death or injury (EU85/374/EEC). This warranty protec ts you against
the following:
• Failure of any components, including the power supply.
• Damage when the product is first removed from its packaging if reported within 24 hours of
purchase.
If you find you do have a problem with this product, you should contact the AV reseller you
purchased this product from. The original purchaser is responsible for shipment of the product
to the manufacturer’s appointed service centre for repair.
We will endeavour to return repaired units within 5 working days, however this may not always
be possible, in which case it will be returned as soon as practicably poss ible. In line with our
WEEE commitments, the manufacturer endeavour s to replace the faulty parts of the prod uct
rather than replacing the whole unit. This warranty does not protect this produc t against faults
caused by abuse, misuse, incorrect installation, unstable or faulty power input, which might be
caused by ignoring the guidelines s e t out in this manual.
LEGAL DISCLAIMER: Because we are committed to improving our products, the details above
may change without prior warning. This User Manual is published without warranty and any
improvements or changes to the User Manual necessitated by typographical errors, inaccuracies
of current information, or improvements to programs and/or equipment, may be made at any
time and without notice. Such changes will be incorporated into new editions of the User
Manual.
Loading...