VISHAY TYPE 131P Technical data
Type 131P
Vishay Sprague
Film Snubber Capacitors
Metal-Case, Paper/Polyester, Dielectric
Extended Foil Electrodes
FEATURES
• Suggested replacement for Type 196P
• Moderate cost
• Small size
• High peak current ratings
• High corona starting voltage
PERFORMANCE CHARACTERISTICS
Operating Temperature: - 65°C to + 125°C.
Capacitance Range: 0.01µF to 0.47µF.
Capacitance Tolerance: ± 20%, ± 10%, ± 5%, ± 2%.
Voltage Rating: 600 WVDC to 1000 WVDC.
Dissipation Factor: 1.0% maximum.
Voltage Test: 200% of rated DC voltage for 2 minutes.
Insulation Resistance: At + 25°C: 20,000 Megohm -
Microfarads or 30,000 Megohm minimum. At + 125°C:
20 Megohm - Microfarads or 250 Megohm minimum.
Capacitance Change with Temperature: At - 65°C,
- 10% typical. At + 125°C, + 10% typical.
ENVIRONMENTAL CHARACTERISTICS
Vibration Test (Condition B): No mechanical
damage, short, open or intermittent circuits.
DC Life Test: 140% of rated voltage for 250 hours @ + 125°C.
No open or short circuits. No visible damage. Maximum
Capacitance Change: ± 5%. Minimum IR = 60% of initial limit.
Maximum DF = 1.0%.
Moisture Resistance: MIL-STD-202, Method 106E, 10
cycles. No visible damage. Maximum Capacitance Change: ±
3%. Minimum IR = 60% of initial limit. Maximum DF = 1.2%.
Thermal Shock and Immersion Cycling: No visible damage.
Maximum Capacitance Change: ± 1%. Minimum IR = 50% of
initial limit. Maximum DF = 1.2%.
PHYSICAL CHARACTERISTICS
Lead Pull: 5 pounds (2.3 kilograms) for one minute.
No physical damage.
Lead Bend: After three complete consecutive bends, no damage.
Lead Wire: Bare, solid tinned wire. Case Diameters: .312"
[7.92mm], No. 22 AWG; .400" [10.16mm] and over, No. 20 AWG.
Marking: Sprague
capacitance and voltage.
STANDARD RATINGS in inches [millimeters]
PART NUMBER
CAPACITANCE
(µF)
0.010
0.022
0.047
0.10
0.22
0.47
0.010
0.022
0.047
0.10
0.22
0.47
* All standard inventoried Part Numbers will be stocked in terminal and case style number S04.
± 10%
TOLERANCE
131P103X9600S02*
131P223X9600S02*
131P473X9600S02*
131P104X9600S02
131P224X9600S02
131P474X9600S02
131P103X91K0S02*
131P223X91K0S02*
131P473X91K0S02*
131P104X91K0S02*
131P224X91K0S02*
131P474X91K0S02*
NOMINAL CASE SIZE
0.312 x 0.875 [7.92 x 22.23]
0.400 x 0.875 [10.16 x 22.23]
0.400 x 1.375 [10.16 x 34.93]
0.562 x 1.375 [14.27 x 34.93]
0.670 x 1.625 [17.02 x 41.28]
0.750 x 2.375 [19.05 x 60.33]
0.400 x 0.875 [10.16 x 22.23]
0.400 x 1.375 [10.16 x 34.93]
0.562 x 1.375 [14.27 x 34.93]
0.670 x 1.625 [17.02 x 41.28]
0.750 x 2.125 [19.05 x 53.98]
1.000 x 2.375 [25.40 x 60.33]
D x L
600 WVDC / 370 VAC
1000 WVDC / 500 VAC
Max. rms
CURRENT
@ +
85°C
0.037
0.058
0.085
0.149
0.354
0.656
0.039
0.079
0.133
0.241
0.427
0.772
®
trademark, type or part number,
Max.
PEAK
CURRENT
@ + 85°C
1.5
3.3
7.0
15.0
33.0
70.0
2.5
5.5
11.0
25.0
55.0
117.0
Max. rms
CURRENT
@ +
125°C
0.025
0.041
0.059
0.104
0.247
0.459
0.027
0.055
0.093
0.168
0.298
0.540
Max.
PEAK
CURRENT
@ + 125°C
1.0
2.3
4.9
10.5
23.1
49.0
1.7
3.8
7.7
17.5
38.5
81.9
ORDERING INFORMATION
131P
TYPE
This is expressed in picofarads.
The first two digits are the
significant figures. The third is the
number of zeros to follow. Values
must conform to the decade rating
for the tolerance specified.
www.vishay.com
98
103
CAPACITANCE
X9
CAPACITANCE
TOLERANCE
X0 = ± 20%
X9 = ± 10%
(Inventoried)
X5 = ± 5%
X2 = ± 2%
For technical questions, contact spresale@vishay.com
* Soldering tabs are available only on case diameters equal to or greater
than 0.400" [10.16mm]. Consult the factory for special case styles and
terminal configurations.
600
DC VOLTAGE
RATING
This is expressed in
volts. (1000 WVDC
coded as 1K0)
S
TERMINAL
S = Wire leads
T = Soldering tab*
04
CASE
STYLE
Note: Inventoried
items are all S04.
Document Number: 42033
Revision 17-Nov-03
Legal Disclaimer Notice
Vishay
Notice
Specifications of the products displayed herein are subject to change without notice. Vishay Intertechnology, Inc.,
or anyone on its behalf, assumes no responsibility or liability for any errors or inaccuracies.
Information contained herein is intended to provide a product description only. No license, express or implied, by
estoppel or otherwise, to any intellectual property rights is granted by this document. Except as provided in Vishay's
terms and conditions of sale for such products, Vishay assumes no liability whatsoever, and disclaims any express
or implied warranty, relating to sale and/or use of Vishay products including liability or warranties relating to fitness
for a particular purpose, merchantability, or infringement of any patent, copyright, or other intellectual property right.
The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications.
Customers using or selling these products for use in such applications do so at their own risk and agree to fully
indemnify Vishay for any damages resulting from such improper use or sale.
Document Number: 91000 www.vishay.com
Revision: 08-Apr-05 1
Loading...