Vintec VIN40BVCALRH Installation Guide

V40-AL SERIES

AL-V40SGE
AL-V40BVC

AL-V40DG2E

UNDERBENCH INSTALLATION INSTRUCTIONS

These units are not designed for outdoor use – please see conditions at the end of this
information.

1. Cabinet dimensions: Allect
Height 820mm – 860mm (40mm adjustable feet) Width 595mm
Depth 571mm + 30mm stopper (=601mm)

2. This cabinet is not designed to be fully integrated behind a joinery door.

✓

3. Please note that a minimum cut out of 615mm is required to facilitate installation, re­moval and servicing.

615

✕

830

4. This cabinet requires 10mm clearance on both sides and the top and 30mm clear­ance at the rear. A ventilation grid MUST be installed in the 30mm clearance at the rear.
Because hot air rises it is imperative that a grille with a Minimum grid size of 200mm x
40mm is installed at the top of the back wall or on either side at the rear at the top giving

cool fresh air full access to ow into the 30mm gap at the rear of the cabinet. This means

that you must not install the grille close to other appliances such as an oven or to an
area that is sealed or with out access to fresh cool air. (You MUST call the Vintec Service
Department on 1800 771 776 if you do not understand any part of this statement. Failing

to comply with the above specications could result in WARRANTY void.)

Suitable points for ventilation grille.
Note: Only one vent is required.

Benchtop

Correct power point location

200

40

5. This cabinet is front venting. The cabinet draws air from the rear and expels through
the grille under the door at the front. If a kick board is to be placed in front of the venti-

lation grill at the front a grill must be tted in to the kick board with a minimum air ow

allowance of 150cm2.

30mm

6. This cabinet has a power switch located on the control panel so powerpoint location is
not critical.

7. This cabinet requires a standard 240 volt/10 amp power point.

8. The power cord is 1.9m in length and is xed on the right side at the back when look­ing from front of cabinet.

1.9m

9. As with most appliances of today, this cabinet has sensitive electronic components
which are susceptible to damage through lightning and electricity supply faults. It is
therefore advised to use a power surge protector to avoid problems of this nature and to
avoid piggybacking with other appliances.

Further Instructions:
The location you have selected for your wine cellar should:

- be unencumbered and well ventilated;

- be well away from any heat source and direct sunlight;

- not be too damp (laundry, pantry, bathroom etc.);

- have a at oor,

- have a standard and reliable electricity supply (standard socket to country standards,
linked to the ground), it is NOT recommended to use a multi-socket or extension lead.

- have a surge protector tted to the electrical outlet away from the microwave.

Certain microwave ovens do not have wave interference shield. When placed within a 1

meter vicinity of the wine cabinet, they may aect the operation of the wine cabinet.

OUT DOOR USE
Please note that, whilst Vintec units are not designed for outdoor use they can be placed
in certain Al Fresco areas but they MUST be well undercover – NEVER exposed to sun­light or the elements.
These units have glass doors & must not be situated where they are exposed to sunlight

or reected sunlight. In areas of high humidity there will be condensation on the glass
doors. The units must be under signicant cover & removed from any heat source (BBQ

etc)
The ventilation requirement indicated for indoor use must be increased when situated
outdoors by at least 2 cm on both sides & 3cm on top, 3 cm at the back with a large
vent at the top of the back wall to facilitate heat evacuation. Because hot air rises it is
imperative that a grille with a Minimum grid size of 200mm x 40mm is installed at the top
of the back wall or on either side at the rear at the top giving cool fresh air full access to

ow into the 30mm gap at the rear.

✕

✓

✕

✕

✓

ONE OR MORE UNITS
The V40 Range can be installed next to each other in a row. All installation instructions
should be followed.

The AL range is equipped with a handle on the front of the unit. When installing a row of
AL units allow a minimum gap of 10mm between each unit.

1825

10

10

10

10

10

10

1220

10

10

10

V40 AL

Notes:

- V40 models are built-in type as per the drawings thereafter;
The wine cellar should be placed where the ambient temperature is between 5oC to
35oC. If the ambient temperature is above or below this range, the performance of the

unit may be aected. Placing your unit in extreme cold or hot conditions may cause inte­rior temperatures to uctuate. The ideal range of temperature may not be reached.

Not complying with any of the above instructions may result in WARRANTY void.

Suitable points for ventilation grille.
Note: Only one vent is required.

Vent Specications

Benchtop

Correct power point location

30mm

600

570

30

555

30

820

10

10

830

595

615

10

525

Front Elevation Top ViewSide View

V40 AL Installation Dimensions