Vintec V40BVCS3, V40DG2EBK User Manual

vintec.com

User Manual

V40BVCBK

V40BVCS3

User Manual

V40BVCBK V40BVCS32

Important information that may impact

!

your Manufacturer’s Warranty

Adherence to the directions for use in this manual is extremely important for health
and safety. Failure to strictly adhere to the requirements in this manual may result
in personal injury, property damage and affect your ability to make a claim under the
Vintec manufacturer’s warranty provided with your product. Products must be used,
installed and operated in accordance with this manual. You may not be able to claim
on the Vintec manufacturer’s warranty in the event that your product fault is due to
failure to adhere this manual.

User Manual

V40BVCBK V40BVCS3 3

WARNING

The information in this document is subject to modification without

•

This

appliance

contains

a

small

quantity

of

R600A

refrigerant

which

is

•

During

transportation

and

installation,

ensure

that

the

tubing

of

the

refrigerant

Avoid

using

or

manipulating

sharp

objects

near

by

the

appliances.

•

Leaking

refrigerant

can

ignite

and

may

damage

the

eyes.

•Inthe

event

any

damage

does

occur,

avoid

exposure

to

open

fires

and

any

device

Thoroughly

ventilate

the

room

in

which

the

appliance

is

located

for

several

•

Notify

Customer

Service

for

necessary

action

and

advice.

any prior notice.

Somes models are available in dedicated countries only.

VINTEC offers no guarantee for our Beverage Center if it is being used for any purpose
other than that for which it was specifically designed. VINTEC cannot be held
responsible for any error in this manual. VINTEC is not responsible or liable for any
spoilage or damage to beverage or any other contents incidental or consequential to
possible defects of the Bev

erag

e Center. Warranty applies to the Beverage Center only and

not to the content of the Beverage Center.

This appliance is not intended for use by persons (including children) with reduc ed
physical, sensory or mental capabilities, or lack of experience and knowledge, unless they
have been given supervision or instruction concerning use of the appliance by a person
responsible for their safety.

Children should be supervised to ensure that they do not play with the appliance.

R600A WARNINGS

The following

els use small quantity of R600A (iso-butane) flammable refrigerant:

mod

V40BVC – 35g S3/BK

For your safety please observe the following recommendations :

environmentally friendly, but flammable. It does not da mage the ozone layer, nor
does it increase the greenhouse effect.

circuit is not damaged.

•

that creates a spark. Disconnect the appliance from the mains power.

•

minutes.

User Manual

V40BVCBK V40BVCS34

•

The

room

for

installing

the

appliance

must

beatleast

1

cubic

metre

per8grams

of

refrigerant. The refrigerant quantity contained in this a ppliance is listed above in
grams; it is also noted on the Rating Plate of the appliance.

It is hazardous for anyone other than an Authorised Service Person to carry out
servicing or repairs to this appliance.

– WARNING: Keep ventilation openings in the appliance enclosure or in the built-in
structure clear of obstruction.
– W ARNING: Do not use mechanical devices or other means to accelerate the defrosting
process, other than those recom

mended by the manufacturer.
– WARNING: Do not damage the refrigerant circuit.
– WARNING: Do not use electrical appliances inside compartments of the appliance.

– WARNING: In Queensland Australia the authorized person must hold a Gas Work
Authorisation for hydrocarbon refrigerants, before carrying out servicing or repairs which
involve the removal of covers.

The environment and personal safety must be considered when disposing of this appliance.
Please ensure the appliance is taken to a recyc

le center for safe recycling. DO NOT
dispose of the appliance in land fill as the insulation and refrigerant gas contained in these
appliances are flammable.

Allow 24 hours before switching on the Beverage Center. During this time we
recommend that you leave the door open to clear any residual odors.

BEFORE LOADING & PLUGGING IN THE BEVERAGE CENTER

Important: All models without front venting (air opening) are strictly for free standing
only. ( see technical chart)

Recommendations:

The locat

ion you have selected for your Beverage Center should:

- be unencumbered and well ventilated;

- be well away from any heat source and direct sunlight;

- not be too damp (laundry, pantry, bathroom etc.);

- have a flat floor;

- have a standard and reliable electricity supply (standard socket to country standards,

linked to the ground), it is NOT recommended to use a multi-socket or extension lead.

- have a surge protector fitted to the electrical outlet;

- away from the microwave oven. Certain micro

wave ovens do not have wave interference

shield. When placed within 1 meter vicinity of the Beverage Center, they may affect the

operation of the Beverage Center.

User Manual

V40BVCBK V40BVCS3 5

The Beverage Center should be placed where the ambient temperature is between 5ºC to

35ºC. If the ambient temperature is above or below this range, the performance of the unit
may be affected. Placing your unit in extreme cold or hot conditions may cause interior
temperatures to fluctuate. The ideal range of temperature may not be reached. (See
Climate Class at the end of this manual)

Grounding instructions

The Beverage Center must be grounded in case of an electrical short circuit. Grounding
re

duces the risk of electrical shock. The Beverage Center is equipped with a power cord

ving a grounding wire and plug. The Beverage Center plug must be plugged into a

ha
properly affixed and grounded electrical outlet.

Note: In locations where there is frequent lightning, surge protectors MUST be used.

Improper use of the grounding plug can result in the risk of electric shock. Consult a
qualified electrician or service person if the grounding instructions are not completely
understood.
If the supply cord i

s damaged, it must be replace by a qualified person in order to avoid

electrical hazard.

nstalling your Beverage Center

I

Unpack and remove all of the protection and adhesive strips from the packaging around
and inside the Beverage Center.
The Beverage Center must be positioned such that the plug is accessible. Release the
power cord. Move your Beverage Center to its final location. The Beverage Center should
be installed in a suitable place where the compressor will not be subject to physical contac
This center cannot be integrated behind a solid door – doing so voids the warranty.

t.

Level

ing your Beverage Center: Beverage Center must be leveled BEFORE

loading
your beverages.
Your Vintec Beverage Center is equipped with 4 adjustable feet to facilitate easy leveling.
VINTEC recommends that you screw the back feet toward the base s o they are in the
shortest position and adjust the front feet to level the Beverage Center.

Back spacer:

Compressor run appliances require proper ventilation for proper and longer usage. Your
Vintec Bever age Center is supplied with a back spacer. Affixed the back spacer at the
back of air circulation and heat evacuation.

User Manual

V40BVCBK V40BVCS36

INSTALLATION FOR VENTILATION PURPOSE. FAILURE TO DO SO VOIDS THE

TURNING ON YOUR BEVERAGE CEN TER

Plug in and switch on the unit by pressing on the power button for a few seconds.
When you use the Beverage C enter for the first time (or restart the Beverage Center after
having it shut off for a long time), the re will be a few degrees, variance between the
temperature you have selected and the one indicated on the LED readout. This
and it is due to the length of the activation time. Once the Beverage Center is running for a
few hours everything will stabilize.

Important: If the unit is unplugged, power is lost, or turned off, wait 5 minutes before
restarting the unit. The Beverage Center will not star t if you attempt to restart before
this time delay.

User Manual

IMPORTANT - THIS SPACER MUST BE ATTACHED TO THE UNIT BEFORE

WARRANTY

is normal

V40BVCBK V40BVCS3 7

Operating Noises

To reach the desired temperature settings, VINTEC Beverage Center, like all Beverage
Centers operating with c ompressors and fans, ma y produce the following types of noises.
These noises are normal and may occur as follows:

- Gurgling sound - caused by the refrigerant flowing through the appliance’s coils.

- Cracking/popping sounds -resulting from the contraction and expansion of the

refrigerant gas to produce cold.

- Fan operating sound - to circulate the air within the Beverag

e Center.

An indivi

dual’s perception of noise is directly linked to the environment in which the

Beverage Center is located, as well the specific type of models. VINTEC Beverage
Centers are in line with international standards for s uch appliances. VINTEC wi ll always
do its utmost to satisfy its customers but will not retake possession of the goods due to
complaints based on normal operating noise occurrences.

LOADING YOUR BEVERAGE CENTER

You may load your beverage bottles in single or double rows while taking note
following: if

you do not have enough bottles to fill your Beverage Center, it is better to

of the

distribute the load throughout the Beverage Center so as to avoid “all on top” or “all
below” type loads.

- Do remove or relocate adjustable shelves to accommodate larger type of bottles or

increase the capacity of the cellar by stacking the bottles up when necessary. (See
removing shelves)

- Keep small gaps between the walls and the bottles to allow air circulation. As in an
underground cellar, air circulation i

s important to pre

vent mould and for a better

homogeneous temperature within the cellar.

- Do not over load your Beverage Center to facilitate air circulation.

- Avoid obstructing the internal fans (located inside on the back panel of the Beverage

Center).

- Do not slide the shelves outwards beyond the fixed position in order to prevent the

bottles from falling.

- Do not pull out more than one loaded shelf at a time as this may cause the Beverage

Center to tilt forward.

- Do not cover the shelves with alloy fo

il or other materi

als, as it will obstruct air

circulation.

- Do not move your Beverage Center while it is loaded with beverages. This might distort

the body of the Beverage Center and cause back injury.

User Manual

V40BVCBK V40BVCS38

TYPES OF REGULATION

Please note that, depending on the loading and settings chosen, it takes about 24 hours for

The

controls

of

your

beverage

center

the Beverage Center to see the temperature stabilizing.

During this time LED seems to move erratically. It is normal and this process occurs
whenever the setting is modified and/or whenever a large amount of bottles are added to
the unit.

TEMPERATURE SETTINGS

Important: The LCD displays, by default, the actual internal air temperature.

The temperature settings are pre-set at the fac

tory setting of 5 ºC.

In the event of a power
interruption, all previous temperature settings are automatically erased and it will revert to
the preset temperature settings.

It is important to understand that there is a difference between the air temperature inside
the Beverage Center and the actual temperature of the Beverage: You will need to wait

approximately 12 hours before noticing the effects of temperature adjustment due to the
critical mass within a full Beverage Center.
Once the temperatu

re is set, it is stron

gly advised not to toy with it or adjust frequently.

The thermostat will maintain the temperature inside the Beverage Center within a +/-

2.5ºC range. But the thermal inertia of the beverages and the glass is such that, within this
temperature range, the actual temperature of the Beverage will only fluctuate 0.5ºC to 1ºC.

User Manual

V40BVCBK V40BVCS3 9

Adjust the desired cooling temperature by pressing the UP or DOWN buttons. Each
depression of the button will scroll through the available temperature settings in
increments of 1 degree Celsius. The temperature setting can be adjusted from 2º to 10º

To visualize the “set” temperature, press and hold the UP or DOWN buttons, the “set”
temperature will temporarily “flash” in the LED display for 5 seconds.

Internal light

In order to reduce energy consumption, this wine cabinet will automatically switch off the
LED lights after 10 minutes.
If you want the LED light to remain on continuously, this is possible. Please press and
hold the "LIGHT" button for 5 seconds, the display will show "LP".After 4 seconds the
display will revert back to normal and the light will remain on until manually switched off.
If you want to revert back and conserve energy (recommended), please press and hold the
"LIGHT" button fo
revert back to normal, and the light will automatically switch off after 10 minutes.

DEFROSTING/CONDENSATION/ HYGROMETRY/ VENTILATION

Your beverage center is designed with “Auto-cycle” defrost system. During “Off-cycle”
the refrigerated surfaces of the beverage center defrost automatically. Defrost water from
the beverage center storage compartment drains automatically and part of it goes into a
drai

nage container
compressor. The heat is transferred from the compressor and evaporates any condensation
that has collected in the pan. Part of the remaining water is collected within the beverage
center for humidity purposes.
This system enables the creation of the correct humidity level inside your beverage center
required by the natural cork to maintain a long lasting seal.

r 5 second, the d

isplay will show "LF",after 4 seconds the display will

, which is located at the back of the beverage center next to the

Notes: The water collected by condensation, is th

erefore recycl

ed. Under extremely dry
environmental conditions, you may have to add some water into the water container
provided with your beverage center.

All units are equipped with a double glazed glass door that has a third internal acrylic
layer to minimize condensation on the glass door.

The beverage center is not totally sealed; fresh air admission is permitted through the
drainpipe. Air is circulated through the unit by means of a fan/fans and the slatted shelves.

Notes: During the refrigerati

ng c ycle, heat i

s given off and disperses through the e xternal

surfaces of the beverage center. Avoid touching the surfaces during those cycles.

ADJUSTABLE SHELVES

Adjusting/removing the shelves

When removing any of these shelves out of the rail compartment - to fit or remove the
shelf - tilt the shelf as per the diagram and simply pull out, or push in the shelf until it sits
on the support brackets securely.

User Manual

V40BVCBK V40BVCS310

REVERSIBILITY OF THE DOOR

-

Depending

on

the

type

of

handle

your

wine

cabinet

is

equipped

with,

the

door

may

not

be

reversible

or

may

require

thataleftorright

opening

door

be

ordered

to

change

the

opening

side.

- While holding the door firmly, remove the three lock screws (2) from the lower

right hinge module, and remove it.!Fig.1)

- Remove the three lock screws (4) from the top right hinge and remove the hinge
(3) . (Fig.3)

- Fix the top left hinge (5) at the top left corner with the three lock screws (4) . (Fig.4)

- While holding the door, insert the axis core into the door’s (7) upper left hinge
hole. Fix the left bottom hinges by inserting the axis core first into the door’s lower
left hinge hole (6). Then secure the lower le

ft hinge to finish the door replacement.

(Fig. 5)

Warning: To avoid accidents during the process of changing the door, we recommend that
you get assistance. The glass door is heavy and may cause injury if dropped.

- Depending on to the model and the type of handle your wine cabinet is equipped with,
you may have to rotate the door through 180 degrees.

V40BVCS3 / V40BVCBK

User Manual

V40BVCBK V40BVCS3 11

1. Lower hinge (Right) 2 . Screws 3 .Door axis

4. Door 5. Top hinge (Right) 6. Hinge Screws

7. Top hinge (Left) 8. Decorative nail 9. Lower hinge (Left)

10. Door limit device 11. Screw

V40/V26/V20 SERIES

Vintec

beverage

Center

dimensions:

V40

Height 820mm – 860mm (40mm adjustable feet)
Width 595mm
Depth 571mm + 30mm stopper (Total of 601mm)

V26

Height 820mm – 830mm (10mm adjustable feet)
Width 380mm
Depth 572mm + 30mm stopper (Total of 602mm)

V20

Height 810mm – 830mm (10mm adjustable feet)
Width 295 – 300mm
Depth 561– 592mm + 30mm stopper (Total of 622mm)

This

Vintec

Beverage

Center

is

not

designed

tobefully

integrated

behind

a

joinery

door.

Please

note

that

:

4.

Remove

decorative

nail

(8)

from

left

topofcabinet

and

install

spare

top

hinge

(Left)

(7)

5.

Following

the

above

procedure,

install

the

spare

lower

hinge

to

the

left

(9).

(Fig.

E)

6.Install

and

aligned

the

door.

Insert

the

plastic

caps

to

cover

the

holes(8).

- While holding the door firmly, remove the three lock screws (2) from the lower

right hinge module, and remove it.!Fig.1)

- Remove the three lock screws (4) from the top right hinge and remove the hinge
(3) . (Fig.3)

- Fix the top left hinge (5) at the top left corner with the three lock screws (4) . (Fig.4)

- While holding the door, insert the axis core into the door’s (7) upper left hinge
hole. Fix the left bottom hinges by inserting the axis core first into the door’s lower
left hinge hole (6). Then secure the lower le

ft hinge to finish the door replacement.

(Fig. 5)

V40BVCS3 / V40BVCBK

1. Lower hinge (Right) 2 . Screws 3 .Door axis

4. Door 5. Top hinge (Right) 6. Hinge Screws

7. Top hinge (Left) 8. Decorative nail 9. Lower hinge (Left)

10. Door limit device 11. Screw

1.

Open

the

door

to90degree

angle,

take

out

the2screws

(2)

from

lower

door

axis

(3),

remove the door (4), Remove the axis plate (3) from the door, (Fig. A).

2.Unscrew

the

screw

(11)

located

underneath

the

door

frame

and

the

limit

device

(10),

3.

Take

out

the3hinge

screws

(6)

from

the

top

hinge

(right)

(5)

and

remove

it.

(Fig.

C)

and re locate it at left end side of the door frame. (Fig. A/B)

at left top of cabinet with 3 screws. (Fig. D)

7.

To provide good performance this cabinet requires adequate ventilation. The Vintec
Beverage Center cabinet requires 10mm clearance on both sides, on top; and 30mm
clearance at the rear. (You must fit the b
minimum 30mm clearance at the rear). A ventilation grid needs to be installed in
this 30mm clearance area at the rear. For good ventilation, it is necessary to install a
grill with a minimum size of 200x40mm at the top of the back wall or on either side
at the top r
fresh air to flow into the 30mm gap at the rear of the cabinet. The ventilation grill
must not be installed close to an oven or next to a s
fresh cool air. (Do call Vintec’s Service Department for further explanation. Failure
to comply with the above specifications could void the WARRANTY.)

ear – refer to diagrams on the following pages. This is to allow cooler

ack spacer provided, it will ensure the

ealed area without access to

User Manual

V40BVCBK V40BVCS312

Front View

VENT SPECIFICATIONS

Front View (V20)

Cross section

User Manual

V40BVCBK V40BVCS3 13

5.

This

Vintec

Beverage

Center

is

front

venting.

The

cabinet

draws

air

from

the

front

and rear and expels through the grill under the door at the front. If a joinery kick

6.

This

unit

hasapower

switch

located

on

the

control

panel.

Power

point

location

is

7.

This

unit

requires

a

standard

240

volt/10

amp

power

point.

8.

The

power

cord

is

1.9m

in

length

andisaffixed

to

the

right

sideatthe

back

of

the

9.Aswith

most

appliances

of

today,

this

cabinet

has

sensitive

electronic

components

10.

Please

see

detailed

dimensional

diagrams

in

the

preceding

pages.

Please

note:

The

board is being placed in front of the Beverage Center, a grill of at least the same
width as the Beverage Center grill and with a minimum airflow allowance of
150cm2 must be installed into the kick board.

therefore not critical.

cabinet.

which are susceptible to damage by lightning and electricity supply faults. It is
therefore advisable to use a power surge protector to avoid problems of this nature.

preceding diagram is for the 85mm plinth recess models.

Further Instructions:
The location you have selected for your Beverage Centre should:

- be unencumbered and well ventilated;

- be well away from any heat source and direct sunlight;

- not be too damp (laundry, pantry, bathroom etc.);

- have a flat floor;

- have a standard and reliable electricity supply (standard socket to country standards,

linked to the ground). It is NOT recommended to use a multi-socket or extension lead;

- have a s

urge protector fitted to the electrical outlet;

- be away from the microwave;
Note: Certain microwave ovens do not have wave interference shield. When placed within
a 1 meter vicinity of the Beverage Center, they may affect the operation of the wine
cabinet.

- do not cover the glass door with any other kind of door - this unit CANNOT be
integrated behind joinery

Notes: Not complying with any of the above instructions may result in WARRANTY void.

User Manual

V40BVCBK V40BVCS314

Dimensional drawings:

*

Dimension and Installation Guide

100 Beer-Bottle Beverage Centre

V40BVCBK

615

10

*

595

10

*

FRONT VIEW SIDE VIEW

593

563

30

30

850

820

Spacer

NOTE: Illustrations not to scale.

All dimensions in millimetres.

* Minimum 10mm required whether proud-t
or ush-t, however 30mm is recommended
on the opening edge for easy nger grip
access when installed ush-t.

Spacer

*

10

*

10

30

TOP VIEW

User Manual

V40BVCBK V40BVCS3 15

V20BVC S3/BK

OPERATION ANOMALIES

Ensure that there is power to the electrical supply plug by connecting another electrical

524

295

30

850

820

10

10

30

30

554

30

524

554

Fron t View

Sid e Vi ew

Top Vi ew

315

Irrespective of the cause, if you notice either abnormal temperature or humidity

to these abnormal conditions can cause a detrimental effect on your beverage.

appliance to it. Check fuse, if any. Make sure that the door is closed properly.

If your beverage center appears to be malfunctioning, unplug it and contact your
VINTEC’s after sales service. Any intervention on the cold circuit should be performed
by a refrigeration technician who should carry out an inspection of the circuit sealing
system. Similarly, any intervention on
qualified electrician.

Notes: Any intervention performed by a non authorized technicians by Vintec wi ll lead to
the warranty being considered as null and void.

POWER FAILURES

In the event of a power interruption, all previous temperature settings are automatically
erased and it will revert to a preset temperature setting .

Most power failures are corrected within a short period of time. An hour or two’s loss of
power will not affect your beverage cent
temperature while the power is off, you should avoid opening the door. For longer period
of power failure, do take steps to protect your beverage.

the electrical circuit should

er temperatures. To avoid sudden

be performed by a

change of

levels inside your beverage center, be reassured that only long and frequent exposure

V40BVCBK V40BVCS316

User Manual

Irrespective of the cause, if you notice either abnormal temperature or humidity
levels inside your beverage center, be reassured that only long and frequent exposure
to these abnormal conditions can cause a detrimental effect on your beverage.
TROUBLESHOOTING GUIDE

Common problems may easily be solved, saving you the cost of a possible service call.

The

circuit

breaker

tripped

or

the

fuse

is

broken.

The

door

gasket

does

not

seal

properly.

The

door

gasket

does

not

seal

properly.

The

light

button

is“OFF

”

.

Vibrations.

Check

to

assure

that

the

Beverage

Center

is

level.

Please read carefully the instruction manual and revert to troubleshooting guide chart.

Beverage center does not operate. Not plugged in.

PROBLEM POSSIBLE CAUSE

The appliance is turned off.

Beverage center is not cold enough. Check the temperature control setting.

External environment may require a higher setting.
The door is opened too often.
The door is not closed completely.

Turns on and off frequently. The room temperature is hotter than normal.

A large amount of contents has been added to the
Beverage center.
The door is opened too often.
The door is not closed completely.
The temperature control is not set correctly.

The light does not work. Not plugged in.

The circuit breaker tripped or a blown fuse.
The light is out of order.

The Beverage center seems to make
too much noise.

The rattling noise may come from the flow of the
refrigerant, which is normal.
As each cycle ends, you may hear gurgling sounds
caused by the flow of refrigerant in your Beverage
center.
Contraction and expansion of the inside walls may
cause popping and crackling noises.
The Beverage Center is not level.

The door will not close properly. The Beverage Center is not level.

The door was reversed and not properly installed.
The gasket is faulty. ( magnet or rubber i
The shelves are out of position.

s spoiled)

User Manual

V40BVCBK V40BVCS3 17

Warranty

FOR SALES IN AUSTRALIA AND NEW ZEALAND

APPLIANCE: ALL VINTEC/TRANSTHERM

This document sets out the terms and conditions of the product
warranties for Vintec/Transtherm Appliances. It is an important
document. Please keep it with your proof of purchase documents
in a safe place for future reference should there be a manufacturing
defect in your Appliance. This warranty is in addition to other rights
you may have under the Australian Consumer Law.

1. In this warranty:

(a) ‘ACL’ or ‘Australian Consumer Law’ means Schedule 2 to the

Competition and Consumer Act 2010;

(b) ‘Appliance’ means any Electrolux product purchased by you and

accompanied by this document;

(c) ‘ASC’ means Electrolux’s authorised serviced centres;

(d) ‘Vintec/Transtherm’ is the brand controlled by Electrolux Home Products

Pty Ltd of 163 O’Riordan Street, Mascot NSW 2020, ABN 51 004
762 341 in respect of Appliances purchased in Australia and Electrolux
(NZ) Limited (collectively “Electrolux”) of 3-5 Niall Burgess Road, Mount
Wellington, in respect of Appliances purchased in New Zealand;

 (e) ‘WarrantyPeriod’meanstheperiodspeciedinclause3ofthis

warranty;

(f) ‘you’ means the purchaser of the Appliance not having purchased

the Appliance for re-sale, and ‘your’ has a corresponding meaning.

2. Application: This warranty only applies to new Appliances, purchased

and used in Australia or New Zealand and is in addition to (and does not
exclude, restrict, or modify in any way) other rights and remedies under
a law to which the Appliances or services relate, including any non­excludable statutory guarantees in Australia and New Zealand.

3. Warranty Period: Subject to these terms and conditions, this warranty

continues for in Australia for a period of 24 months and in New Zealand
for a period of 24 months, following the date of original purchase of the
Appliance.

4. Repair or replace warranty: During the Warranty Period, Electrolux

or its ASC will, at no extra charge if your Appliance is readily accessible
for service, without special equipment and subject to these terms and
conditions, repair or replace any parts which it considers to be defective.
Electrolux may, in its absolute discretion, choose whether the remedy

oeredforavalidwarrantyclaimisrepairorreplacement.Electroluxorits

ASC may use refurbished parts to repair your Appliance. You agree that
any replaced Appliances or parts become the property of Electrolux.

5. Travel and transportation costs: Subject to clause 7, Electrolux will

bear the reasonable cost of transportation, travel and delivery of the
Appliance to and from Electrolux or its ASC. Travel and transportation will
be arranged by Electrolux as part of any valid warranty claim.

6. Proof of purchase is required before you can make a claim under this

warranty.

7. Exclusions: You may not make a claim under this warranty unless the

defect claimed is due to faulty or defective parts or workmanship. This
warranty does not cover:

 (a) lightglobes,batteries,ltersorsimilarperishableparts;

(b) parts and Appliances not supplied by Electrolux;

 (c) cosmeticdamagewhichdoesnotaecttheoperationofthe

Appliance;

(d) damage to the Appliance caused by:
(i) negligence or accident;

(ii) misuse or abuse, including failure to properly maintain or service;

(iii) improper, negligent or faulty servicing or repair works done by

anyone other than an Electrolux authorised repairer or ASC;

(iv) normal wear and tear;

(v) power surges, electrical storm damage or incorrect power supply;

(vi) incomplete or improper installation;

(vii) incorrect, improper or inappropriate operation;

(viii) insect or vermin infestation;

(ix) failure to comply with any additional instructions supplied with

the Appliance;

In addition, Electrolux is not liable under this warranty if:

(a) the Appliance has been, or Electrolux reasonably believes that the

Appliance has been, used for purposes other than those for which
the Appliance was intended, including where the Appliance has
been used for any non-domestic purpose;

 (b) theApplianceismodiedwithoutauthorityfromElectroluxinwriting;

(c) the Appliance’s serial number or warranty seal has been removed

or defaced.

8. How to claim under this warranty: To enquire about claiming under

this warranty, please follow these steps:

(a) carefully check the operating instructions, user manual and the

terms of this warranty;

(b) have the model and serial number of the Appliance available;

(c) have the proof of purchase (e.g. an invoice) available;

(d) telephone the numbers shown below.

9. Australia: For Appliances and services provided by Electrolux in

Australia: Electrolux goods come with guarantees that cannot be
excluded under the Australian Consumer Law. You are entitled to a
replacement or refund for a major failure and for compensation for any
other reasonably foreseeable loss or damage. You are also entitled to
have the Appliance repaired or replaced if the Appliance fails to be of
acceptable quality and the failure does not amount to a major failure.
‘Acceptable quality’ and ‘major failure’ have the same meaning as
referred to in the ACL.

10. New Zealand: For Appliances and services provided by Electrolux

in New Zealand, the Appliances come with a guarantee by Electrolux
pursuant to the provisions of the Consumer Guarantees Act, the Sale
of Goods Act and the Fair Trading Act. Where the Appliance was
purchased in New Zealand for commercial purposes the Consumer
Guarantee Act does not apply.

11.Condentiality: You accept that if you make a warranty claim, Electrolux

and its agents including ASC may exchange information in relation to you
to enable Electrolux to meet its obligations under this warranty.

Before calling for service, please ensure that the steps listed in clause 8 above have been followed.

FOR SERVICE

ortondtheaddressofyournearest

authorised service centre in Australia

PLEASE CALL 1800 771 776

For the cost of a local call (Australia only)

FOR SERVICE

ortondtheaddressofyournearest

authorised service centre in New Zealand

PLEASE CALL 0800 550 020

(New Zealand only)

ALL_Vintec_Transtherm_May17

Important Notice

AUSTRALIA

ELECTROLUX HOME PRODUCTS

163 O’Riordan Street, Mascot NSW 2020

vintec.com.au

NEW ZEALAND

ELECTROLUX (NZ) Limited

3-5 Niall Burgess Road, Mount Wellington

vintec.co.nz

FOR ACCESSORIES

PLEASE CALL 1800 666 778

For the cost of a local call (Australia only)

or visit www.vintecclub.com

FOR ACCESSORIES

PLEASE CALL 0800 550 020

(New Zealand only

or visit www.vintecclub.com

User Manual

V40BVCBK V40BVCS3 19

Service and support

In the rare event that your Vintec cabinet does not perform
to your satisfaction, contact our dedicated support team:

1800 771 776

[e-mail]

Vintec. We are part of the
Electrolux Family. To add
a touch of professional
inspiration to your home,
visit electrolux.com.au

Stay in touch and share your
user experience by following us:

@vintecclub

© 2018 Electrolux Home Products Pty Ltd. ABN 51 004 762 341

VMAN_V40s_BVCS3_BVCBK_Jun18

vintec.com