Viking VK PB7 PIXELBLADE 7 User Manual

VK PB7 PIXELBLADE 7

MOVING HEAD

USER MANUAL

Rev 2.01

CAUTION ! EYE DAMAGE !

Avoid looking directly into the LED light source!

This device has left our premises in absolutely perfect condition. In order to maintain this condition and to en­sure a safe operation, it is absolutely necessary for the user to follow the safety instructions and warning notes
written in this manual.

The manufacturer will not accept liability for any resulting damages caused by the non-observance of this
manual or any unauthorized modification to the device.

Please consider that damages caused by manual modifications to the device are not subject to warranty.

1. Safety instructions

Make sure that the available voltage is not higher than stated on the rear panel of the fixture.
This fixture should be operated only from the type of power source indicated on the label. If you are not
sure of the type of power supplied, consult your authorized distributor or local power company.

Always disconnect the fixture from AC power before cleaning, removing or installing the fuses, or any part.
The power plug has to be accessible after installing the fixture. Do not overload wall outlets and extension cords

as this can result in fire or electric shock.
Do not allow anything to rest on the power cord. Do not locate this fixture where the cord may be damaged by

persons walking on it.
Make sure that the power cord is never crimped or damaged by sharp edges. Check the fixture and the power

cord from time to time.
Refer servicing to qualified service personnel.

Do not connect this fixture to a dimmer pack.
During the initial start-up some smoke or smell may arise. This is a normal process and does not necessarily

mean that the device is defective.
Do not touch the device’s housing with bare hands during its operation (housing becomes
hot)!

For replacement use lamps and fuses of same type and rating only.

FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY

BEFORE YOU INITALLY START

This light was designed for indoor use and it is intended for

professional application only. It is not for household use.

CAUTION!

Disconnect the fixture from mains before you remove any cover of the fixture.

With a high voltage you can suffer a dangerous electric shock when touching

live wires and electrical parts under covers!

This fixture falls under protection class I. Therefore this fixture has to be connected to

a mains socket outlet with a protective earthing connection.

If the fixture has been exposed to drastic temperature fluctuation (e.g. after transportation), do not switch it on
immediately. The arising condensation water might damage your device. Leave the device switched off until
it has reached room temperature.

Do not shake the fixture. Avoid brute force when installing or operating the fixture.
This fixture was designed for indoor use only; do not expose this unit to rain or use near water.
When choosing the installation spot, please make sure that the fixture is not exposed to extreme heat, moisture

or dust.
Air vents and slots in the fixture´s head and base are provided for ventilation, to ensure reliable operation of

the device and to protect it from overheating.
Do not block the front objective lenses with any object when the fixture is under operation.
The openings should never be covered with cloth or other materials, and never must be blocked.
The fixture becomes hot during operation. Allow the fixture to cool approximately 5 minutes prior to

examination.
This fixture should not be placed in a built-in installation unless proper ventilation is provided.
Only operate the fixture after having checked that the housing is firmly closed and all screws are tightly

fastened.
Always use a secondary safety cable when mounting this fixture.
Make sure that the area below the installation place is blocked when rigging, derigging or servicing the

fixture.

The maximum ambient temperature 45°C must never be exceeded.

Operate the device only after having familiarized with its functions. Do not permit operation by persons not
qualified for operating the device. Most damages are the result of unprofessional operation!

Please use the original packaging if the device is to be transported.

Warning

The minimum distance between light output and the illuminated surface must be more

than 0.5 meters.

CAUTION!

The lenses have to be replaced when obviously damaged,

so its function is not impaired, e. g. due to cracks or deep scratches!

CAUTION!

Fast on-off-cycles (e.g. 10 min. on / 10 min. off) will reduce equipment

life.

2. Installation

2.1 Connection to the mains

The VK PB7 Pixelblade 7 is equipped with auto-switching power supply that automatically adjusts to any
50-60Hz AC power source from 100-240 Volts.
This fixture must be earthed. To use the fixture, a plug must be fixed.
The correct assembly of a sufficient plug may be done by professional persons only.
The conductors in the cable are marked by the following table.

Core (EU) Core (US) Connection Plug Terminal Marking

Brown
Light blue
Green /Yellow

Black
White
Green

Live
Neutral
Earth

L
N

Fixtures must be installed by a qualified electrician in accordance with all

national and local electrical and construction codes and regulations.

For protection from electric shock, the fixture must be earthed!