Viking RVDW103WSSS Installation

Installation

Built-In Dishwashers

VDW302 / VDW302WS

RVDW103

FDW103WS/ FDW302WS

CFDW103 / CFDW302

/ RVDW103WS

FDW103 / FDW302

Table of Contents

Important Safety Instructions __________________________________________________________3 Tools Which May Be Needed _________________________________________________________5 Materials Which May Be Needed ______________________________________________________6 Materials Supplied ___________________________________________________________________7

Parts Supplied ___________________________________________________________________7 Dishwasher Specifications ____________________________________________________________8 Enclosure Preparation ________________________________________________________________9

Electrical Preparation _____________________________________________________________9

Preparation for Installing Mounting Brackets_________________________________________9

Adjusting Height_________________________________________________________________9

Installing the Side Trim Strips _____________________________________________________10

Preparing the Water Connection__________________________________________________11

Drain Preparation _______________________________________________________________12

Steam Protection Foil____________________________________________________________13 Installation_________________________________________________________________________14

Drain Hose Connection, Water Supply & Electrical Connections ______________________14

Preparation of Water Supply _____________________________________________________15

Electrical Connection ____________________________________________________________18

Readjusting Foot Levels _________________________________________________________19

Adjusting Moveable Kickplate ____________________________________________________19

Installing a Custom Panel ________________________________________________________21 Installer Checklist ___________________________________________________________________26 Final Instructions ___________________________________________________________________26 Service & Registration_______________________________________________________________27

IMPORTANT3– Please Read and Follow

Site Preparation

It is recommended that a thorough site inspection be conducted PRIOR to unpacking and moving this appliance.

• Please read this installation manual and

particularly the safety instructions completely and carefully. They will save you time and effort and help to ensure optimum dishwasher performance.

• Be sure to observe all listed warnings and

cautions. Look particularly for the icons with exclamation marks inside. The information icon also will provide important references.

WARNING

Indicates a potentially hazardous

situation which, if not avoided,

could result in death or serious injury.

CAUTION

Indicates a potentially hazardous

situation which, if not avoided,

may result in injury. It may also be used

to alert against unsafe practices.

NOTICE

Indicates a potentially hazardous

situation which, if not avoided,

may result in damage to the dishwasher,

the tableware, the equipment, or

the environment.

In addition to these instructions, the dishwasher shall be installed:

• In accordance with all local codes or, in absence of a local code,

• In the United States, with the national Electric Code,

• In Canada, with the Canadian Electric Code C22.1-latest edition/Provincial and Municipal codes and/or local codes.

WARNING

Read these installation instructions completely before installing and follow them carefully. Save these installation instructions and pass them on to any future user.

When installing the dishwasher, follow basic precautions, including the following:

• The dishwasher should only be converted from cord-connected to permanently connected by an authorized service representative.

• Installation and repair should be performed by a qualified installer. Work by unqualified persons could be dangerous and may void the warranty.

NOTICE

Installation should be performed by an insured licensed plumber, contractor, or trained installer. Installation performed by persons other than this could result in improper installation and property damage.

NOTICE

• Do not discard any bags or items that come with the original package until after the entire installation has been completed.

• DO NOT operate the appliance if damaged, malfunctioning, partially disassembled, or if it has missing or broken parts.

• Also follow the safety instructions of the use and care guide.

• To reduce the risk of electric shock, fire, or injury to persons, the installer must ensure that the dishwasher is completely enclosed at the time of installation.

• Only connect the dishwasher to the power supply when all installation and plumbing work is complete.

• If the dishwasher is installed in a location that experiences freezing temperatures (e.g. in a vacation home, cabin, etc.), you must drain all the water from the dishwasher’s interior. Water system ruptures that occur as a result of freezing are not covered by warranty.

• Dishwasher must be secured to adjacent cabinetry using the brackets provided. Failure to do this may cause damage to property or bodily injury.

• Connect to a properly rated, protected, and sized power supply circuit to avoid electrical overload. The dishwasher is designed for an electrical supply of 120V (volts), 60Hz (hertz), AC, connected to a dishwasher-dedicated, properly grounded electrical circuit with a fuse or breakers rated for 15 amperes. Electrical supply conductors shall be a minimum of #16 AWG copper wire rated at 167°F (75°C) or higher. These requirements must be met to prevent injury and machine damage. Consult a qualified electrician if in doubt.

• DO NOT use any extension cord or portable outlet device to connect the dishwasher to a power supply.

• Ensure that any plastic wrappings, bags, small pieces, etc., are disposed of safely and kept out of the reach of children. Danger of suffocation!

• Remove the dishwasher door when removing an old dishwasher from service or discarding it. Ensure that the appliance presents no danger to children while being stored for disposal.

• Old appliances may contain materials that can be recycled. Please contact your local recycling authority about the possibility of recycling these materials.

NOTICE

• The dishwasher drain hose must be installed with a drain loop at least 28” (710mm) off the cabinet floor; otherwise the dishwasher may not drain properly.

• This dishwasher is intended for residential use only and should not be used in commercial establishments.

• New Installation: If the dishwasher is a new installation, most of the work must be done before the dishwasher is moved into place.

• Replacement: If the dishwasher is replacing another dishwasher, check the existing dishwasher connections for compatibility with the new dishwasher, and replace parts as necessary.

• Inspect the Dishwasher: After unpacking the dishwasher and prior to installation, thoroughly inspect the dishwasher for possible freight or cosmetic damage. Report any damage immediately.

To contact us, you may either call our toll-free number at 1-888-845-4641 or contact us via the website in the US (www.vikingrange.com) or in Canada (www.brigade.ca).

IMPORTANT– Please Read and Follow

General Information

Tools Which May Be Needed

Pipe Wrench Wire Cutter Drill

Hole Saw Hammer Wire Stripper

Tape Measure Torx Screwdriver

(T20)

Phillips Screwdriver

Adjustable Wrench Slot Screwdriver Scissors

Level Brush Pencil

General Information

Materials Which May Be Needed

Hot Water Supply Line – Minimum 3/8” O.D. copper tubing or metal braided dishwasher supply line.

90° elbow with 3/8” N.P.T. male threads on one leg, and sized to fit your water supply line (copper tubing/compression fitting, or braided hose) on the other leg.

UL listed conduit connector or strain relief.

Teflon tape or other pipe thread compound to seal plumbing connections.

Shut-off valve and fittings appropriate for hot water supply line (copper tubing/compression fitting, or braided hose).

Silicone.

Glue.

General Information

Materials Supplied

Dishwasher Parts Bag 1

This dishwasher bag comes with the following parts:

a. Side Trim Strips – Left b. Side Trim Strips – Right c. Adjusting Wrench d. Screws Ø 1/8”x5/8”

(Ø 3.5mmx14mm)

e. Mounting Bracket – Left f. Mounting Bracket – Right g. Spring Clamp h. Screw Clamp j. Rubber Connector k. Kickplate Bracket – Left l. Kickplate Bracket – Right m. Edge Protector n. Clips o. Kickplate

(kickplate without slots)

p. Kickplate r. Screws Ø 1/8”x3/8”

(Ø 3.9mmx9mm)

s. Plastic Caps t. Screws Ø 3/16”x1/4”

(Ø 4mmx6mm)

z. Steam Protection Foil

Dishwasher Parts Bag 2 v. Screws Ø 1/8”x5/8”

(Ø 3.5mmx14mm)

y. Screws Ø 3/16”x1-3/4”

(Ø 4mmx43mm)

Parts Attached to the Rear of the Dishwasher a. Side Trim Strips – Left b. Side Trim Strips – Right o. Kickplate

(Kickplate without slots)

p. Kickplate

Parts Supplied

Parts for your dishwasher will come in several plastic bags. Check your parts bags to make sure you have all the parts as listed below.

Specifications

Built-In Dishwasher

Overall Width

Overall Height from Floor

Overall Depth from Rear

Cutout Width

Cutout Height

Cutout Depth

Electrical Requirements

Water-Heating Element Rating

Inlet Water Temperature

Inlet Water Pressure Operating Range

Inlet Water Hose

Drain Hose

Drain Hose High Loop Required

Approximate Shipping Weight

23-9/16” (59.8 cm)

33-7/8 (86.0 cm) min. to 35-7/8" (91.1 cm) max.

without door panel – 21 5/8” (54.9 cm)

with door panel – 22 3/16” (156.4 cm)

24" (61.0 cm)

34" (86.4 cm) min. to 36" (91.4 cm) max.

24" (61.0 cm)

12.0 amps, 120V/60 Hz; 4’ (1.2 m) electrical cord supplied with unit

1240 watts

120°F (49°C) required

4.35 to 145 psi (.3 - 10 bar)

Minimum 3/8" OD copper tubing or braided metal water line required.

6.4' (1.9 m) drain hose provided

Height from floor – 28" (71.1 cm)

97 lbs. (44 kg)

NOTICE

Because we continually strive to improve our products, we may change our specifications and design without prior notice. This device corresponds to the following directives: UL 749 Household Dishwasher Directive.

24” max

(61.0 cm max)

24” max

(61.0 cm max)

24” max

(61.0 cm max)

Electrical Preparation

Preparation for Installing Mounting Brackets

Enclosure Preparation

WARNING

The dishwasher is designed for an electrical supply of 120V, 60Hz, AC, connected to a dishwasher-dedicated, properly grounded electrical circuit with a fuse or breaker rated for 15 amperes.

• Place the two mounting brackets into the top corners of the dishwasher.

• Fix the mounting brackets (A) to the top corners of the dishwasher, with the screws supplied.

• Bend sides of mounting brackets (B) in order to fix from sides (if necessary).

WARNING

Dishwasher must be secured to adjacent cabinetry using the mounting brackets provided. Failure to do this may cause damage to property or bodily injury.

Adjusting Height

If the height of the enclosure is 33-7/8” to 35-7/8” (86.1cm-91.1cm), adjust supports as shown in the figure.

Supplied (4)

+ 19 hidden pages