Viking Outdoor Cabinets User Manual

F20402E EN (070113)

Viking Range, LLC

111 Front Street

Greenwood, Mississippi 38930 USA [phone]

For product information,

call 1-888-(845-4641)

or visit the Viking Web site in the U.S. at

vikingrange.com or in Canada at brigade.ca

Use/Installation Guide

Outdoor Cabinets

3

Illustration #3

Illustration #4

Install 4 Tinnerman clips (provided)
before fastening cabinets together

Mount cabinets
with #10 x 1/2”
screws provided

Use #8 x 3/8” machine screw and
locknut to fasten hole cover to
inside door panel

Use #8 x 3/8” flat
head M.S. and
locknut to attach
hinge bracket to
the inside door.

7. Cabinet doors must be adjusted when cabinets are
level in final position. There are two adjustment
screws on the hinge receiver. (See Illustration #5)

•The front screw is used to center the door in
the opening. Turning the front screws in or
out will center the door over the cabinet
opening.

•The back screw is used to align the front of
the door with the cabinet frame and secure
the door to the cabinet. Slightly loosen the
screw and slide door in or out. Retighten the
screw to secure the door.

Illustration #5

Front Screw

5. Place cabinet(s) in approximate final position.
Level cabinets using leveling legs. Use 1/2"
SMS screws provided to screw cabinets
together. (See illustration #3).

6. Determine appropriate hinge side for cabinets
with interchangeable doors. Remove outside
door panel. Install hinges by placing plate in
hole in door and fasten in place with hardware
provided. Screw hinge plates in appropriate
pre-drilled holes in cabinet side. Fasten hole
covers with hardware provided. (See
Illustration #4).

Back Screw

2

IMPORTANT - PLEASE READ AND FOLLOW

•Before beginning, please read these instructions completely and carefully.

•Do not remove permanently affixed labels, warnings, or plates from product. This may void the warranty.

•Viking outdoor stainless steel cabinets are not designed to be water tight. Water may enter cabinetry under certain
conditions

•The installer should leave instructions with the consumer who should retain for future reference

•NEVER

use LP tanks inside any stainless steel cabinetry. Tanks must be located outside of the cabinetry at all times.

TO INSTALL CABINETS:

1. Verify cabinet product number(s) on

box(es) to list of cabinets ordered.

2. Carefully unpack cabinets making sure

not to scratch fronts. Front panels are
protected by plastic coating (that must
be removed after setup). Cabinets with
interchangeable doors are shipped from
the factory with opening from left to
right as shown (See illustration #1).

3. In cabinets with interchangeable doors,

hardware package will contain hole
covers and hardware to install.

4. Install 4 legs in the leg plates attached to

bottom of each cabinet. Screw in place.
(See illustration #2).

Illustration #1

Illustration #2

Cabinet box ready
for assembly

5

10. BACK PANEL INSTALLATION

•Remove all protective covering from panel and install using the #10 x 1/2” tek screws provided. (See
Illustration #8).

•Attach rear toe kick to legs. (See illustration #8).

NOTE: For end of the run panels, the rear, front, and side toe kicks must be modified. (See illustrations #7 & #8)

2. Fasten from inside with (4) 1/2” tek screws provided

Back panel

1. Place back panel onto cabinet area

3. After modifying rear toe kick (See dimension
chart at the bottom of page 4) - snap toe
kick into place

Rear toe kick

11. INSTALL LOCALLY SUPPLIED COUNTERTOP
Viking outdoor cabinets are designed for a minimum countertop thickness of 1 1/8” (2.9 cm) such as you would
find with granite or quartz material. If a countertop material thicker than 1 1/2” (3.8 cm) is used, the appliances
should be shimmed to the proper height. For examples of common installations, see the Viking Stainless Steel
Planning Guide.

12. Install Viking appliances per each appliance's installation instructions.

Complete Cabinet

Illustration #8

4

8. If desired, snap toe kick
included with each unit to
front legs. (See illustration
#6).

Illustration #6

Illustration #7

Snap toe kick to front
legs

9. SIDE PANEL INSTALLATION (End of Run Only)

•Remove all drawers. (If applicable)

•Remove all protective covering from panel and install using the #10 x 1/2” tek screws provided. (See
Illustration #7)

•Attach toe kick to legs (See Illustration #6).

NOTE:

FOR WALL INSTALLATIONS:
The front portion of the side toe kick must be shortened to match the front toe kick. (See Illustration #7).
The plastic material can be cut with any common type wood saw blade.
FOR ISLAND INSTALLATIONS:
The side, front, and rear toe kick must be modified (See Illustration #7)

2. Attach from inside (front and rear)

1. Place side panel into area of
the cabinet

Side toe kick (B)Front toe kick (A)

LH Side Panel Installation

(RH installs the same way)

Toe Kick Dimensions

Wall Installation Island Installation

Front Toe Kick (A) 16 3/4” (42.5 cm) 16 3/4” (42.5 cm)
Side Toe Kick (B) 27 1/4” (61.6 cm) 25 1/2” (64.8 cm)
Rear Toe Kick (C) N/A 16 3/4” (42.5 cm)

PROFESSIONAL SERIES

OUTDOOR CABINET WARRANTY

TWO YEAR FULL WARRANTY

Outdoor cabinets and all of their component parts, except as detailed below*, are warranted to be free from defective materials or workmanship in normal household
use for a period of two (2) years from the date of original retail purchase. Viking Range, LLC, warrantor, agrees to repair or replace, at its option, any part which fails
or is found to be defective during the warranty period.

*Decorative items are warranted to be free from defective materials or workmanship for a period of ninety (90) days from the date of original retail purchase. ANY
DEFECTS MUST BE REPORTED TO THE SELLING DEALER WITHIN NINETY (90) DAYS FROM DATE OF ORIGINAL RETAIL PURCHASE.

TWO YEAR LIMITED WARRANTY

Any door hinges or drawer slides which fail due to defective materials or workmanship in normal household use during the second year from the date of original retail
purchase will be repaired or replaced, free of charge for the part itself, with the owner paying all other costs, including labor.

LIFETIME LIMITED WARRANTY

During the life of the product, any stainless steel parts found to be defective in material or workmanship will be repaired or replaced, free of charge for the part itself,
with the owner paying all other costs, including labor. This warranty excludes surface corrosion or rust, scratches, discoloration, water or atmospheric conditions, or
cleaning practices which are part of normal residential use.

This warranty extends to the original purchaser of the product warranted hereunder and to each transferee owner of the product during the term of the warranty.

TERMS AND CONDITIONS

This warranty extends to the original purchaser of the product warranted hereunder and to each transferee owner of the product during the term of the warranty and
applies to products purchased and located in the United States and Canada. Products must be purchased in the country where service is requested. If the product or one
of its component parts contains a defect or malfunction during the full warranty period after a reasonable number of attempts by the warrantor to remedy the defect or
malfunction, the owner is entitled to either a refund or replacement of the product or its component part or parts. Replacement of a component part includes its free
installation, except as specified under the limited warranty. Under the terms of this warranty, service must be performed by a factory authorized Viking Range, LLC service
agent or representative. Service will be provided during normal business hours, and labor performed at overtime or premium rates shall not be covered by this warranty.

Owner shall be responsible for proper installation, providing reasonable and necessary maintenance, providing proof of purchase upon request, and making the appliance
reasonably accessible for service. The return of the Owner Registration Card is not a condition of warranty coverage. You should, however, return the Owner Registration
Card so that Viking Range, LLC can contact you should any question of safety arise which could affect you.

This warranty gives you specific legal rights, and you may also have other rights which may vary from jurisdiction to jurisdiction.

WHAT IS NOT COVERED BY THIS WARRANTY: This warranty shall not apply to damage resulting from abuse, failure to provide reasonable and necessary maintenance,
accident, delivery, negligence, natural disaster, loss of electrical power to the product for any reason, alteration, outdoor use, improper installation, improper operation, or
repair or service of the product by anyone other than an authorized Viking Range, LLC service agency or representative. This warranty does not apply to commercial
usage.

LIMITATION OF REMEDIES AND DURATION OF IMPLIED WARRANTY

OWNER’S SOLE AND EXCLUSIVE REMEDY FOR A CLAIM OF ANY KIND WITH RESPECT TO THIS PRODUCT SHALL BE THE REMEDIES SET FORTH ABOVE. VIKING RANGE, LLC IS NOT
RESPONSIBLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGE, INCLUDING BUT NOT LIMITED TO FOOD OR MEDICINE LOSS, DUE TO PRODUCT FAILURE, WHETHER ARISING OUT OF
BREACH OF WARRANTY, BREACH OF CONTRACT OR OTHERWISE. Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or
exclusions may not apply to you. ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE APPLICABLE TO THIS PRODUCT ARE LIMITED IN DURATION TO
THE PERIOD OF COVERAGE OF THE APPLICABLE EXPRESS WRITTEN LIMITED WARRANTIES SET FORTH ABOVE. Some states do not allow limitations on how long an implied warranty lasts, so
the above limitation may not apply to you.

WARRANTY SERVICE

To obtain warranty service, contact an authorized Viking Range, LLC service agent, or Viking Range, LLC, 111 Front Street, Greenwood, Mississippi 38930, [phone]. Provide model and serial
number and date of original purchase or closing date for a new construction. For the name of your nearest authorized Viking Range, LLC service agency, call Viking Range, LLC.
IMPORTANT: Retain proof of original purchase to establish warranty period.

Specifications subject to change without notice.

Specifications subject to change without notice.

1. Carefully remove protective plastic peel coat from each stainless steel surface. Clean stainless with stainless steel
cleaner in direction of grain. Clean the stainless with any product made for stainless. Always rub with the grain
direction. Rubbing across the grain direction may produce minor scratches. Some good cleaners are Stainless Steel
Magic™, and Sheila Shine™.

2. In a salt air environment, small amounts of rust may accumulate on stainless steel. A slightly more oily cleaner like Sheila
Shine™ will protect better against oxidation or slight surface rust. Cleaning the surfaces periodically will protect the
finish for many years.

CARE AND MAINTENANCE

CAUTION

•Do not use a metal knife or any other metal tool to scrape stainless steel parts.

•Do not permit citrus or tomato juice to remain on stainless steel surfaces, as citric acid will permanently discolor
stainless steel. Wipe up any spills immediately.

•Do not use abrasive cleaners, steel wool pads, or abrasive cloths as they will scratch the product.

76

OVERALL WIDTH OVERALL HEIGHT OVERALL DEPTH

VBBO1601 15 5/8” (39.7 cm) 34 1/2” (87.6 cm) 29 7/8” (75.9 cm)
VBBO2602 26 3/8” (67.0 cm) 34 1/2” (87.6 cm) 29 7/8” (75.9 cm)
VBO1811, including doors 18” (45.7 cm) 34 1/2” (87.6 cm) 29 7/8” (75.9 cm)
VTPO1810, including doors 18” (45.7 cm) 34 1/2” (87.6 cm) 29 7/8” (75.9 cm)
VBO1830, including doors 18” (45.7 cm) 34 1/2” (87.6 cm) 29 7/8” (75.9 cm)
VSBO2402, including doors 24” (61.0 cm) 34 1/2” (87.6 cm) 29 7/8” (75.9 cm)
VSBO3602, including doors 36” (91.4 cm) 34 1/2” (87.6 cm) 29 7/8” (75.9 cm)
VQBO3021, VQWO3010 30 1/4” (76.8 cm) 34 1/2” (87.6 cm) 29 7/8” (75.9 cm)
VQBO4121, VQWO4120 41 7/8” (106.4 cm) 34 1/2” (87.6 cm) 29 7/8” (75.9 cm)
VQBO5322, VQWO5311 53 7/8” (136.8 cm) 34 1/2” (87.6 cm) 29 7/8” (75.9 cm)
VERO3200 32” (81.3 cm) 68” (172.7 cm) 29 7/8” (75.9 cm)
VEUO3202 32” (81.3 cm) 68” (172.7 cm) 29 7/8” (75.9 cm)
VGRO3200 32” (81.3 cm) 68” (172.7 cm) 29 7/8” (75.9 cm)
VGUO3202 32” (81.3 cm) 68” (172.7 cm) 29 7/8” (75.9 cm)
VURO3200 32” (81.3 cm) 34 1/2” (87.6 cm) 29 7/8” (75.9 cm)
VURO2400 24” (61.0 cm) 34 1/2” (87.6 cm) 29 7/8” (75.9 cm)
VBPFLR4 4” (10.2 cm) 34 1/2” (87.6 cm)* 3/4” (1.9 cm)
VFLR4 4” (10.2 cm) 34 1/2” (87.6 cm)* 3/4” (1.9 cm)
VBPFLR8 8” (20.3 cm) 34 1/2” (87.6 cm)* 3/4” (1.9 cm)
VFLR8 8” (20.3 cm) 34 1/2” (87.6 cm)* 3/4” (1.9 cm)
VSP30 29 7/8” (75.9 cm) 34 1/2” (87.6 cm)* 0”
VTSP30 29 7/8” (75.9 cm) 68” (172.7 cm)* 0”
VTHP30 29 7/8” (75.9 cm) 34” (86.4 cm)* 0”
VCF90 3” (7.6 cm)** 34” (86.4 cm)* 3/4” (1.9 cm)
VOCF90 33” (83.8 cm)** 34 1/2” (87.6 cm)* 3/4” (1.9 cm)
VCF135 3” (7.6 cm)** 34 1/2” (87.6 cm)* 3/4” (1.9 cm)
VOCF135 15 1/2” (39.4 cm)** 34 1/2” (87.6 cm)* 3/4” (1.9 cm)
VBP16 16” (40.6 cm) 34 1/2” (87.6 cm)* 3/4” (1.9 cm)
VBP18 18” (45.7 cm) 34 1/2” (87.6 cm)* 3/4” (1.9 cm)
VBP24 24” (61.0 cm) 34 1/2” (87.6 cm)* 3/4” (1.9 cm)
VBP26 26 3/8” (67.0 cm) 34 1/2” (87.6 cm)* 3/4” (1.9 cm)
VBP30 30 7/8” (78.4 cm) 34 1/2” (87.6 cm)* 3/4” (1.9 cm)
VBP32 32” (81.3 cm) 34 1/2” (87.6 cm)* 3/4” (1.9 cm)
VBP36 36” (91.4 cm) 34 1/2” (87.6 cm)* 3/4” (1.9 cm)
VBP41 41 7/8” (106.4 cm) 34 1/2” (87.6 cm)* 3/4” (1.9 cm)
VBP53 53 7/8” (136.8 cm) 34 1/2” (87.6 cm)* 3/4” (1.9 cm)
VTBP32 32” (81.3 cm) 68” (172.7 cm)* 3/4” (1.9 cm)

BASIC SPECIFICATIONS

*includes provided toe kick
**from inside of turn to next cabinet

WARRANTY