Viking C-200, C-2000A, E-30-PT, E-35-EWP Technical Practice

PPrraaccttiicce

e

T

T

EELLEECCOOM

M

S

S

OOLLUUTTIIOONNSSFFOORRTTHHE

E

221

1

SST

T

C

C

EENNTTUURRY

Y

TECHNICAL

TECHNICAL

Handsfree Speaker Phone with Built-In

Auto-Dialer and Color Video Camera

The E-35 is a weather and vandal resistant handsfree video
phone designed to provide quick and reliable handsfree commu­nication and CCTV video of who is at your door or gate. The E-
35 can be connected directly to a C.O. line, analog PABX/KSU
station, or a Viking Door/Gate Controller: C-200 or C-2000A.

The E-35 features non-volatile memory, a built in dialer, a built-in
high resolution color video camera, and intelligent call progress
detection for automatic hang-up when the call is completed.

The E-35 can be programmed to dial up to 5 different numbers on
ring no answer or busy and can be configured to dial these num­bers until answered.

For extreme outdoor environments or corrosive atmospheres, the

E-35 is available with Enhanced Weather Protection (EWP).
EWP products feature rubber gaskets and boots, closed cell foam gasketing, hand soldered silicon

sealed connections, anti-corrosive gel filled butt connectors, as well as urethane encapsulated circuit
boards with internally sealed, field-adjustable trim POTS and DIP switches.

FFeeaattuurrees

s

Dimensions: Overall-127mm x 127mm x 57mm (5” x 5” x 2.25”),
Plastic Electrical Box-102mm x 102mm x 54mm (4” x 4” x 2.12”)

Shipping Weight: 1 Kg (2.2 lbs)
Operating Temperature: -34°C to 65°C (-30°F to 150°F)
Connections: Standard model: (3) gel-filled butt connectors (3M

Scotchlok UR2) and 2-position terminal block, EWP model: (5)
gel-filled butt connectors (3M Scotchlok UR2)

(See page 2 for complete specifications)

SSppeecciiffiiccaattiioonns

s

E-35/E-35-EWP

E-35/E-35-EWP

Handsfree Speaker

Phone with Dialer and

Color Video Camera

January 5, 2009

AApppplliiccaattiioonns

s

Gate and Door Entry Phones for:

• Business lobbies • Residences

• Auto or pedestrian gates

Non-ADA Hot-Line Phones for:

• Elevators • Stadiums

• Parking lots/ramps • Convention centers

• ATM machines

E-35 shown with

optional VE-5x5

CAUTION - 1 When installing on an analog extension of a phone system:

Some phone systems do not conform to analog telecom standards and might
not be compatible with the E-35 speaker phones. For a detailed description of
the telephone line specifications required for any of the E-35 phones, retrieve
Fax Back Document 869. 2 In louder background noise environments, the
push to talk version may be required (E-30-PT or E-30-PT-EWP).

• Built-in 5 number auto-dialer

• Built-in high resolution color video camera with wide viewing
angle, tilt/swivel adjustments and wide operating temperature
of -30°F to 150°F

• Audio and video transmission on one CAT5E cable (page 5)

• Vandal Resistant Features: 14 gauge louvered stainless
steel faceplate with stainless steel speaker/mic screen,
heavy duty metal “Call” button, impact and scratch resistant
camera lens and hex drive mounting screws

• Weather Resistant Features: Mylar speaker, faceplate
gasket, mic and speaker gasket, internally sealed (IP67)
push button switch, sealed camera lens, potted camera
circuit board, stainless steel phone and camera
mounting hardware

• Optional Enhanced Weather Protection (EWP) conforms to
NEMA requirements

• Red “off-hook” LED

• Volume adjustments for microphone and speaker

• Advanced call progress detection: disconnects on busy
signal, return to dial tone, CPC, reorder signal, maximum
call time out and selectable silence time out

• Selectable auto-answer feature for monitoring

• Selectable push button disconnect

• Optional VE-5x5 surface mount box available

• Selectable maximum call time

• Selectable VOX switching speed

?

Need More Information on EWP?

Call [phone] and select 859.

PPhhoonnee......771155..338866..8888661

1

hhttttpp::////wwwwww..vviikkiinnggeelleeccttrroonniiccss..cco

omm

IF YOU HAVE A PROBLEM WITH A VIKING PRODUCT, PLEASE CONTACT: VIKING TECHNICAL SUPPORT AT [phone]

Our Technical Support Department is available for assistance Monday 8am - 4pm and Tuesday through Friday 8am - 5pm central time. So that we can give you better service, before you call please:

1. Know the model number, the serial number and what software version you have (see serial label).

2. Have your Technical Practice in front of you.

3. It is best if you are on site.

RETURNING PRODUCT FOR EXCHANGE

The following procedure is for equipment that has failed out-of-box (within 10 days of purchase):

1. Customer must contact Viking’s Technical Support at 715-386-8666 to determine possible causes for the problem. The

customer MUST be able to step through recommended tests for diagnosis.

2. If the Technical Support Product Specialist determines that the equipment is defective based on the customer's input
and troubleshooting, a Return Authorization (R.A.) number will be issued. This number is valid for fourteen (14)
calendar days from the date of issue.

3. After obtaining the R.A. number, return the approved equipment to your distributor, referencing the R.A. number. Your
distributor will then replace the product over the counter at no charge. The distributor will then return the product to
Viking using the same R.A. number.

4. The distributor will NOT exchange this product without first obtaining the R.A. number from you. If you haven't
followed the steps listed in 1, 2 and 3, be aware that you will have to pay a restocking charge.

RETURNING PRODUCT FOR REPAIR

The following procedure is for equipment that needs repair:

1. Customer must contact Viking's Technical Support Department at 715-386-8666 to obtain a Return Authorization (RA)

number. The customer MUST have a complete description of the problem, with all pertinent information regarding the
defect, such as options set, conditions, symptoms, methods to duplicate problem, frequency of failure, etc.

2. Packing: Return equipment in original box or in proper packing so that damage will not occur while in transit. Static
sensitive equipment such as a circuit board should be in an anti-static bag, sandwiched between foam and individual­ly boxed. All equipment should be wrapped to avoid packing material lodging in or sticking to the equipment. Include
ALL parts of the equipment. C.O.D. or freight collect shipments cannot be accepted. Ship cartons prepaid to:

Viking Electronics, 1531 Industrial Street, Hudson, WI 54016

3. Return shipping address: Be sure to include your return shipping address inside the box. We cannot ship to a PO Box.

4. RA number on carton: In large printing, write the R.A. number on the outside of each carton being returned.

the necessary modifications to maintain uninterrupted service.
If trouble is experienced with the E-35, for repair or warranty information, please contact:
Viking Electronics, Inc., 1531 Industrial Street, Hudson, WI 54016 [phone]
If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the

equipment until the problem is resolved.
Connection to Party Line Service is subject to State Tariffs. Contact the state public utility commission, public service com-

mission or corporation commission for information.

WHEN PROGRAMMING EMERGENCY NUMBERS AND (OR) MAKING TEST CALLS TO EMERGENCY NUMBERS:

Remain on the line and briefly explain to the dispatcher the reason for the call. Perform such activities in the off-peak
hours, such as early morning or late evenings.

It is recommended that the customer install an AC surge arrester in the AC outlet to which this device is connected. This
is to avoid damaging the equipment caused by local lightning strikes and other electrical surges.

PART 15 LIMITATIONS

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communica­tions. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will
be required to correct the interference at his own expense.

FCC REQUIREMENTS

This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. Inside the front panel
of this equipment is a label that contains, among other information, a product identifier in the format US:AAAEQ##TXXXX.
If requested, this number must be provided to the telephone company.

The REN is used to determine the number of devices that may be connected to a telephone line. Excessive REN's on a
telephone line may result in the devices not ringing in response to an incoming call. In most but not all areas, the sum of
the REN's should not exceed five (5.0) To be certain of the number of devices that may be connected to a line, as deter­mined by the total REN's, contact the local telephone company. For products approved after July 23, 2001, the REN for
this product is part of the product identifier that has the format US:AAAEQ##TXXXX. The digits represented by ## are the
REN without a decimal point (e.g., 03 is a REN of 0.3). For earlier products, the REN is separately shown on the label.

The plug used to connect this equipment to the premises wiring and telephone network must comply with the applicable
FCC Part 68 rules and requirements adopted by the ACTA. If your home has specially wired alarm equipment connected
to the telephone line, ensure the installation of this E-35 does not disable your alarm equipment. If you have questions
about what will disable alarm equipment, consult your telephone company or a qualified installer.

If the E-35 causes harm to the telephone network, the telephone company will notify you in advance that temporary dis­continuance of service may be required. But if advance notice isn't practical, the telephone company will notify the cus­tomer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is nec­essary.

The telephone company may make changes in its facilities, equipment, operations, or procedures that could affect the
operation of the equipment. If this happens, the telephone company will provide advance notice in order for you to make

LIMITED WARRANTY

Viking warrants its products to be free from defects in the workmanship or materials, under normal use and service, for a period of one year from the date of purchase from any authorized Viking distributor or 18 months from the date manu­factured, which ever is greater. If at any time during the warranty period, the product is deemed defective or malfunctions, return the product to Viking Electronics, Inc., 1531 Industrial Street, Hudson, WI., 54016. Customer must contact Viking's
Technical Support Department at 715-386-8666 to obtain a Return Authorization (R.A.) number.

This warranty does not cover any damage to the product due to lightning, over voltage, under voltage, accident, misuse, abuse, negligence or any damage caused by use of the product by the purchaser or others.

NO OTHER WARRANTIES

. VIKING MAKES NO WARRANTIES RELATING TO ITS PRODUCTS OTHER THAN AS DESCRIBED ABOVE AND DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTIES OR MERCHANTABILITY OR FIT-

NESS FOR ANY PARTICULAR PURPOSE.

EXCLUSION OF CONSEQUENTIAL DAMAGES

. VIKING SHALL NOT, UNDER ANY CIRCUMSTANCES, BE LIABLE TO PURCHASER, OR ANY OTHER PARTY, FOR CONSEQUENTIAL, INCIDENTAL, SPECIAL OR EXEMPLARY DAM-

AGES ARISING OUT OF OR RELATED TO THE SALE OR USE OF THE PRODUCT SOLD HEREUNDER.

EXCLUSIVE REMEDY AND LIMITATION OF LIABILITY

. WHETHER IN AN ACTION BASED ON CONTRACT, TORT (INCLUDING NEGLIGENCE OR STRICT LIABILITY) OR ANY OTHER LEGAL THEORY, ANY LIABILITY OF VIKING SHALL

BE LIMITED TO REPAIR OR REPLACEMENT OF THE PRODUCT, OR AT VIKING'S OPTION, REFUND OF THE PURCHASE PRICE AS THE EXCLUSIVE REMEDY AND ANY LIABILITY OF VIKING SHALL BE SO LIMITED.

IT IS EXPRESSLY UNDERSTOOD AND AGREED THAT EACH AND EVERY PROVISION OF THIS AGREEMENT WHICH PROVIDES FOR DISCLAIMER OF WARRANTIES, EXCLUSION OF CONSEQUENTIAL DAMAGES, AND EXCLU­SIVE REMEDY AND LIMITATION OF LIABILITY, ARE SEVERABLE FROM ANY OTHER PROVISION AND EACH PROVISION IS A SEPARABLE AND INDEPENDENT ELEMENT OF RISK ALLOCATION AND IS INTENDED TO BE ENFORCED
AS SUCH.

Camera Specifications

Power: 5-9V DC regulated 150mA (6V DC adapter included)
Image Sensor: 1/4” color CMOS
Video Output: 1 VP-P composite, NTSC, 75 ohms
Resolution: 420 lines (640 x 480 @ 30fps / 307,200 pixels)
Sensitivity: 0.26 LUX (20 IRE) F 2.0
Lens: 3.4mm, pinhole 70° FOV (Field of View)
Tilt/Swivel Adjustment: Vertical +/- 20°, horizontal +/- 30° (see Diagram A)
Maximum Wire Run Length: 1000 ft with *RG59/RG6 for video and CAT5 for power (dou-

bled pairs) and entry phone audio. 150 ft with CAT5E for video, power and entry phone audio
(longer video runs are possible by using video balun transceivers, see Installation section F,
page 5). * Note: RG59 or RG6 with solid center conductor and 95% bare copper braid shield.

SSppeecciiffiiccaattiioonns

s

Entry Phone Specifications

Power: Telephone line powered. Minimum 24V DC talk battery voltage,

with a minimum loop current of 20mA loop. Loop current may be boosted
on low current lines with a Viking Model TBB-1A talk battery booster (Fax

Back # 630).
Dimensions: Overall: 127mm x 127mm x 57mm (5” x 5” x 2.25”), Plastic

electrical box: 102mm x 102mm x 57mm (4” x 4” x 2.25”)

Shipping Weight: 1.6 kg (3.5 lbs)
Speaker Volume: Approximately 70 db maximum @1m
Ring Voltage: 25V AC RMS minimum (for auto answer)
CPC Disconnect Time: 500ms minimum
REN #: 0.5 A

Entry Phone / Camera Specifications

Operating Temperature: -34° C to 65° C (-30° F to 150° F)
Humidity: Standard model: 5% to 95% non-condensing, EWP

model: Up to 100%
Connections: Standard model: (3) gel-filled butt connectors (3M
Scotchlok UR2), EWP model: (5) gel-filled butt connectors (3M
Scotchlok UR2)

Recommended Surface Mount Box: Viking model VE-5x5 (Fax
Back Document 424)

2

Diagram A

Camera Field of View:

Rotate
Left 30°

70° Lens FOV

Rotate
Right 30°

Camera Lens

FFeeaattuurreessOOvveerrvviieew

w

IInnssttaallllaattiioon

n

The optional VE-5x5 Surface Mount Box is designed
to be surface mounted to a single gang box, double
gang box or VE-GNP gooseneck pedestal (right).

Important: The E-35 will NOT mount
to a standard double gang box.

Caution: When warm air comes in contact with cold surfaces, such as outside walls and conduits, it causes condensation. To prevent
condensation from accumulating inside the E-35 always bring conduit into the bottom of the unit. If this is not possible, drill a 1/4” diam­eter hole in the bottom of the gray plastic box.

*Note: Peel off paper liner and adhere gasket to the back of the faceplate, centering it over the four corner mounting holes. Be careful
to position the modular jack inside the chassis as not to damage the components on the circuit board.

Note: The plastic rough-in box (part # 259576) may be purchased separately
in advance. Go to www.vikingelectronics.com and click on “Spare Parts”.

?

Need More Information on VE-5x5 or VE-GNP?

Call [phone] and select 424.

IMPORTANT: Electronic devices are susceptible to lightning and power station electrical surges from both the AC outlet and the
telephone line. It is recommended that a surge protector be installed to protect against such surges. Contact Panamax at (800)
472-5555 or Electronic Specialists Inc. at [phone].

!

A. Mounting

3

Mounting Screws: 6-32 x 0.75" long
flathead with 5/64" hexdrive, 18-8 stainless
steel to prevent corrosion.

Faceplate: 14 guage 304 stainless steel.

Color Video Camera: Wide operating

temperature range of -30°F to 150°F, NTSC
composite video output with 420 lines of
resolution, 70° wide viewing angle lens, tilt and
swivel adjustments for aiming towards visitors.

Protective Camera Window: Impact resistant
polycarbonate lens with scratch resistant
coating and water-tight gasket.

Condensation Drain Hole

DIP Switches (see page 7):

1: Normal Audio Detection
2: Increased Audio Detection

Speaker Volume

Microphone Volume

VIKING

Microphone: Omni-directional microphone
with protective water-resistant cloth.

Speaker: Mylar speaker with rubber gasket to
maintain water-tight seal and eliminate water
deterioration.

Speaker Screen: Stainless steel speaker
screen with 0.018" diameter holes to prevent

Call

©

ON

1

2

punctures from paperclips, etc.

Push Button Switch: Push to initiate call,
push again to disconnect. Solid 304 stainless
steel internally sealed per IP67.

LED: Lights red for "In-Use" indication.

Faceplate Gasket: 1/8" thick closed cell PVC

to provide a water-tight seal.

Earth Ground: To increase surge protection,
loosen the screw labeled (as shown) and

DIP Switches (see page 7):

1: Push Button Feature (connect / disconnect)
2: Auto Answer Feature (on/off)
3: Programming Switch (normal/programming)

fasten a wire with ring terminal (included) from
the mounting screw to Earth Ground (grounding
rod, water pipe, etc.)

(4) 0.38” diameter
(for gooseneck mounting)

(4) 0.2 x 0.43 slots

for double gang box

(2) 0.2 x 0.43 slots
for single gang box

(1) .74" dia

Drain Hole

3.0”

Rear View of VE-5x5

(not included)

3.0” 3.3”

E-35 shown with

Viking Model

VE-GNP

Gooseneck

Pedestal

4.0"

Wall Stud

Front View of

Plastic Rough-In

Box (included)

Wire knock out

(2) Standard flat head dry wall
(sheet rock) screws (not included)

2.1”

* Adhere gasket to front panel,

centering over mounting holes

5.0”

Call

Push to Call Button

Red Off-Hook LED Indicator

Condensation Drain Hole

(4) 6-32 X 3/4” stainless steel, flat
head, hexdrive, screws (included)

5.14”

2.25”

5.22”

3.25”

Condensation

Front View of Optional

VE-5x5 (not included)

*** Note: To increase surge protection, loosen the PCB mounting screw labeled (as shown above) and fasten a wire with spade terminal (included)
from the mounting screw to Earth Ground (grounding rod, water pipe, etc.)

** Note: The gel-filled (water-tight) butt connectors are designed for insulation displacement on 19-26 gauge wire with a maximum insulation of 0.082
inches. Cut off bare wire ends prior to terminating.

* Note: When installing a line powered phone on a low voltage and/or low loop
current phone system extension, a TBB-1 Talk Battery Booster may be required.

?

Need More Information on the TBB-1?

Call [phone] and select 630.

B. Wiring the E-35 Phone Board

C. Wiring the E-35 Camera

1. Using RG59 for Video and CAT5 for Camera Power and Phone Board Audio (Recommended)

IMPORTANT: Electronic devices are susceptible to lightning and power station electrical surges from both the AC outlet
and the telephone line. It is recommended that a surge protector be installed to protect against such surges. Contact
Panamax at [phone] or Electronic Specialists Inc. at [phone].

!

4

Optional C-2000A Advanced Door

Entry Controller (not included)

Fax Back Number 156

VIKING

©

MODEL C-2000A

VIKING

ELECTRONICS

HUDSON, WI 54016

ADVANCED DOOR/GATE AND
ENTRY PHONE CONTROLLER

PWR 13.8 VAC

EARTH GND

ENTRY PHONE 1

DOOR STRIKE 1

ENTRY PHONE 2

DOOR STRIKE 2

ENTRY PHONE 3

DOOR STRIKE 3

ENTRY PHONE 4

DOOR STRIKE 4

PHONE LINE

INPUT

LINE OUT

TO PHONES

1 2 3 4 5678 9 10 1112 13 14 15 16 17 18 19 20 21 22 23 24 25 2627 28 29 30

DOORBELL SWITCH /

Optional C-200 Basic Single Entry

Phone Interface (not included)

Fax Back Number 169

VIKING

C

SINGLE ENTRY PHONE

A
V
.8
3
1
R
W
P

RING COUNT

RELAY MODE

DOORBELL MODE

AUX. INPUT

AUX. CONTACT

OUTPUT

ON

1 2 3

©

MODEL C-200

VIKING

ELECTRONICS

HUDSON, WI 54016

CONTROLLER

EARTH

GND

LINE OUT

TO PHONES

PHONE LINE

INPUT

12345 89

EARTH

C.O. LINE

OUT TO

GND

INPUT

PHONES

5.0”

3.63”

Rear View of

* C.O. Line

OUTPUT

or Analog

PABX/KSU

Station

or

Butt Connectors

Y

S

A

T

L

C

E

A
T

R

N

X
U

O

TO ENTRY

PHONE

A

C

AUX POWER

67

10

11 12

ENTRY

N.O. COM N.C.

AUX POWER

PHONE

AUX CONTACTS

OUTPUT

or

the E-35

** Gel-Filled

Red (Ring)

Green (Tip)

ON

1

2

5.0”

3.63”

Ring

Terminal

(included)

*** Earth

Ground

(optional)

Back View of the E-35

3-Wire Gel-Filled Butt Connectors

ON

1

2

included (3M Scotchlok UR2)

Yellow (Video)

- Black (GND)

+ Red (6VDC)

Center conductor
stripped back 5/8"

Twisted foil and
braided shield

** Camera GND (-) W/O

** Camera Pwr (+) O/W

Phone Board Audio In/Out (Tip) W/BL

Phone Board Audio In/Out (Ring) BL/W

*** RG59 or RG6

Shielded

Video Cable

Up to 1000 ft

CAT5 Cable

** Up to 500 ft

"F"

Connector

BL/W W/BL

"F" to Phono Plug

Shack part #278-252)

W/O

O/W

(Radio

Adapter

Camera GND (-)

Camera Power (+)

See page 4, section E

Wiring Phone Board

To unused input on TV,
VHF modulator, whole
house video distribution
equipment, etc.

6V DC Adapter

(included)

Black

(-)

(+)

Black with
White Stripe

Crimp-on Splice

Connectors (not included)

!

120V AC

* Note: Up to 150 ft video cable run length can be achieved using CAT5E or CAT6 cable. Longer cable runs can be used if a passive or active video Balun transceiver is used on
each end of the cable. Generally, passive transceivers can achieve up to 750 ft cable runs where active transceivers can achieve up to 3000 ft runs depending on cable type, etc.
The type of video balun transceiver required is specific to your cable run length. For more information on video balun transceivers go to: www.northernvideo.com.

Caution: When routing CAT5E or CAT6 cable, maintain a minimum distance of 3 ft from any parallel high voltage wire (110 VAC) and a minimum of 2 ft from crossing any high volt­age wire. For installations where RF noise is expected (commercial applications) or wire runs are near high voltage (110 VAC) wires, a shielded video cable such as RG6 is recom­mended.

G. Adjusting the Camera

The camera can be tilted and rotated to your desired posi­tion. A portable service (test) monitor can be used to
determine the correct viewing angle during installation.

Important: To prevent the edge of the faceplate from
being viewed in the video image, do not rotate the cam­era beyond 30 degrees or tilt beyond 20 degrees.

Vertical (Tilt)

Adjustment

+/- 20 degrees

maximum

Horizontal (Rotation)

Adjustment

+/- 30 degrees maximum

Call

VIKING

©

** Note: The maximum camera power supply wire run length is 500 ft of 24 gauge wire (CAT 5/6), longer runs are possible by doubling pairs or increasing the wire gauge.

2. Using CAT5E or CAT6 for Video, Camera Power and Phone Board Audio (see Caution below)

*** Note: RG59 or RG6 with solid center conductor and 95% bare copper braid shield.

PPrrooggrraammmmiinng

g

Step 1. Move DIP switch 2 to the ON position (sets unit to answer incoming calls - see section F).

Step 2. From a Touch Tone phone call the line attached to the E-35.

Step 3. When the E-35 answers, enter the 6-digit security code (factory set to 845464 - see section C). A double beep

should then be heard indicating you have entered the programming mode.

2. Without the Security Code

A. Accessing the Programming Mode

1. Using the Security Code

Step 1. Move DIP switch 2 to the ON position (sets unit to answer incoming calls - see section F).

Step 2. Move DIP switch 3 to OFF (incoming calls enter the programming mode without security code - see section F).

Step 3. From a Touch Tone phone call the line attached to the E-35.

Step 4. When the E-35 answers, a double beep will be heard and you will automatically enter the programming mode.

Step 5. When finished programming, move DIP switch 3 back to the ON position (see section F).

Note: If a valid memory position is entered, a double beep will be heard, four beeps indicate an error.

?

Need More Information on the DLE-200B?

Call [phone] and select 605.

The E-35 phone can be programmed from any Touch Tone phone using a C.O. line, analog PABX/KSU station, or a
DLE-200B Line Simulator.

5

Back View of the E-35

ON

1

2

3-Wire Gel-Filled Butt

Connectors included

(3M Scotchlok UR2)

Yellow (Video)

- Black (GND)

+ Red (6VDC)

Phone Board Audio In/Out (Tip) W/BL

Phone Board Audio In/Out (Ring) BL/W

Video Out (+) W/G

Video GND (-) G/W

** Camera GND (-) W/O

** Camera Pwr (+) O/W

CAT5E or

CAT6 Cable

(see Caution below)

* Up to 150 ft

W/G G/W

W/O

O/W

BL/W W/BL

Video Out (+)

Video GND (-)

Camera GND (-)

Camera Power (+)

See page 4, section E

Wiring Phone Board

To unused input on TV, VHF

modulator, whole house video

distribution equipment, etc.

Phono (RCA) Plug,

F Connector, Etc.

6V DC Adapter

(included)

Black

(-)

(+)

Black with
White Stripe

(4) Crimp-on Splice

Connectors (not included)

(-)

(+)

!

120V AC

E. Timing/Dialing Options (Memory Location #18)

There are six positions in the timing/dialing options. To program these options, enter the six desired timing/dialing dig­its followed by #18. The six available timing/dialing options are defined as shown below.

Dial: A +B+C+D+E+F+#+1+8

Factory Default Setting:2+3 +4+1+ 1+1

Talk/Listen Delay
Call Length
Silence Time Out
Dial Next Number on Ring No Answer
Dial Next Number on Busy
Pulse Dial Speed

Enter Timing/Dialing Settings Here:

A B C D E F

#18

Setting A - Talk/Listen Delay

This feature selects switching time between talk and listen modes
(VOX switching time). Use chart at the right. * Note: The factory

default is .2 seconds.

Setting B - Call Length Time Out

This feature selects the maximum length of time that calls can be connected. Programmable
in increments of 1 minute up to a maximum of 9 minutes (Touch Tones 1 - 9). Program 0 in
this location to disable the call length time out. With the call length disabled, the E-35 phone
must rely on CPC, busy, reorder, silence or return dialtone to hang-up. Use chart at the far
right. *Note: The factory default is 3 minutes.

Touch

Tone

1
2
3
4
5
6
7
8
9

Talk/Listen

Delay

.1 sec

.2 sec *

.3 sec
.4 sec
.5 sec
.6 sec
.7 sec
.8 sec
.9 sec

Touch

Tone

0
1
2
3
4
5
6
7
8
9

Call Length

Time Out

Disabled

1 min
2 min
3 min*
4 min
5 min
6 min
7 min
8 min
9 min

D. Speed Dial Numbers (Memory Locations #00 - #04)

Note: Up to 20 digits can be stored in each dial position. Special features such as pause, mode change, Touch Tone

,

and # count as single digits.

The speed dial number programmed in location #00 is the telephone or extension
number that is dialed when the “Call” button is first pressed. Additional speed dial
numbers will be dialed when there is no answer or a busy signal is detected and the
next number redial features are activated. The E-35 will cycle through the pro­grammed speed dial numbers until answered. To program, enter the desired speed
dial number followed by the memory location number (#00 - #04).

To clear a speed dial location, simply enter the memory location (#00 - #04) alone.
The E-35 is factory set with no speed dial number programmed.

To Program:

,

#

4 second pause

switch to pulse mode

0, 1, 2...9

Enter:

,,

,#

,7

,6

0, 1, 2...9

B. Quick Programming Features

First speed dial number ...........................................................................................

Second speed dial number ......................................................................................

Third speed dial number ..........................................................................................

Fourth speed dial number ........................................................................................

Fifth speed dial number ...........................................................................................

To add a

, at any point in the dialing string ...............................................................

To add a # at any point in the dialing string ...............................................................

To add a four second pause at any point in the dialing string ....................................

Toggle between Touch Tone and Pulse dialing .........................................................

Timing/Dialing options (factory set to 234111) .........................................................

Change security code (factory set to 845464) .........................................................

0-20 digits
0-20 digits
0-20 digits
0-20 digits
0-20 digits

,,
,#
,7
,6

6 digits (0-9)
6 digits (0-9)

#00
#01
#02
#03
#04

#18
#19

Enter Digits

then
then
then
then
then

then
then

- then -

Enter Memory Location

C. Security Code (memory location #19)

The security code allows the user/installer to program the E-35 phone while DIP switch 3 is in the ON (normal) posi­tion. The factory set security code is 845464 (V-I-K-I-N-G). It is recommended that the factory set security code be
changed. Example: To store 123456 as the security code:

Enter Your Security Code Here:

#19

Step 1. Access programming as shown is Programming section A.

Step 2. Enter 123456 #19..

Step 3. Hang-up.

Note: The security code must be 6 digits and cannot include a ,or a #.

6

The lap counter is a programmable counter that determines how many times the E-35 will cycle through its list of up to 5 emer­gency number (or up to 3 “Info” phone numbers), before it stops the dialing process and hangs up. When all of the programmed
phone numbers have been dialed, the lap counter is incremented and the dialing process repeats. When the lap counter has
been met, the dialing process stops and the E-30 hangs up. * Note: This feature is disabled in the factory default setting.

Setting C - Silence Time Out

This feature selects the length of time that calls will remain connected without voice activity.
Programmable in increments of 10 seconds up to a maximum of 90 seconds (Touch Tones
1 - 9). To disable the silence time out, program 0 in this location. Use chart at the right.
* Note: The factory default is 40 seconds.

Setting D - Dial Next Number on Ring No Answer

If enabled and a ring-no-answer is detected, the E-35
phone will dial the next programmed speed dial num­ber, and continue to cycle through the emergency
numbers until a call is completed. * Note: This feature is disabled in the factory default.

Touch

Tone

0
1
2
3
4
5
6
7
8
9

Silence

Time Out

Disabled

10 sec
20 sec
30 sec
40 sec*
50 sec
60 sec
70 sec
80 sec
90 sec

If enabled and a busy is detected, the E-35 phone will dial the next programmed
speed dial number, and continue to cycle through the emergency numbers until a
call is completed. * Notes: This feature is disabled in the factory default setting. If

the busy signal is interrupted with a promotional message, contact your central
office to have it removed.

Setting E - Dial Next Number on Busy

Setting F - Pulse Dialing Rate (Pulses per Second)

The E-35 phone is capable of different pulse dialing speeds. * Note: The factory
default setting is 10pps (pulses per second).

Touch Tone

1
2

Setting F

10 pps*
20 pps

Touch Tone

1 or 0
2, 3, 4...9

Setting D

Disabled*
Dials second number after
2, 3, 4...9 rings respectively

Touch Tone

1
2

Setting E

Disabled*
Enabled

7

Settings A /B/C-NotApplicable

F. Miscellaneous Options (memory location #17)

Dial: A +B+C+D+E+F+#+1+7

Factory Default Setting:0+0 +0+2+ 1+0

Not Applicable (enter 0)
Hang-up on Return to Dial Tone
Panasonic Mode
Lap Counter

Enter Settings Here:

A B C D E F

0 0 0 #17

If enabled and a return dial tone is detected, the E-35 will hang up.

* Note: The factory default setting is enabled.

Touch Tone

1
2

Setting D

Disabled
Enabled*

Setting D - Hang Up on Return to Dial Tone

The E-35 can be programmed to recognize the double ring cadence that is typical of
Panasonic phone systems. If the E-35 is connected to a Panasonic extension, (or any other
system that provides a double ring cadence) enable “Panasonic Mode” will allow for proper
call progress detection.

* Note: This feature is disabled in the factory default setting.

Touch Tone

1
2

Setting E

Disabled*
Enabled

Setting E - Panasonic Mode

With the lap counter disabled (factory setting), if the E-35 is programmed to dial
the next number on ring-no-answer and/or busy signal (see page 6 and 7), the
E-35 will continuously call its programmed phone numbers forever until the call
is answered.

Touch Tone

0
1-9

Setting F

Disabled*
Lap count = 1-9 times

Setting F - Lap Counter

Due to the dynamic nature of the product design, the information contained in this document is subject to change without notice. Viking Electronics, and its affiliates and/or subsidiaries
assume no responsibility for errors and omissions contained in this information. Revisions of this document or new editions of it may be issued to incorporate such changes.

DOD# 178

ZF302550 Rev B

Printed in the U.S.A.

PPrroodduuccttSSuuppppoorrttLLiinnee......771155..338866..8866666

6

FFaaxxBBaacckkLLiinnee......771155..338866..4433445

5

8

OOtthheerrPPrroodduucctts

s

The E-50 Series Video Entry phones are compact, weather and vandal resistant speaker phones
designed to provide two-way handsfree audio communication and color composite video of who is at your
door or gate. The E-50's compact size allows it to be mounted in a standard single gang electrical box.
The E-50 is available in five different attractive finishes to match your door hardware, light fixtures, etc.
Replacement E-50 faceplates (PNL50) can be purchased separately and are available in all five standard
finishes. The E-50 features a built-in high resolution color video camera, microphone and speaker vol­ume controls, selectable auto answer for monitoring and intelligent call progress detection for automatic
hang-up when the call is completed. For extreme outdoor environments or corrosive atmospheres, the E-
50 Series is available with Enhanced Weather Protection (EWP).

Compact Video Entry Phones Available in Five Finishes

OOppeerraattiioon

n

When the “Call” button is pressed, the E-35 phone goes off-hook, and dials a pre-programmed telephone number. The front
panel LED will light any time the phone is off hook. In the event that the line is busy or there is a ring-no answer, the unit
can be programmed to call additional phone numbers. The phone then cycles through up to 5 pre-programmed speed dial
numbers until the call is answered. The E-35 will hang up on CPC, silence, busy signal, return to dial tone, time out or Touch
Tone command (

,#). If programmed to auto-answer, the E-35 will also answer any incoming call. The E-35 color video

camera operates completely independently of the E-35 phone board. With power supplied to the camera, it will continuously
output a video signal.

To Program the E-35 Phone...

...to store 123456 as the security code

...to store a Touch Tone 9, a four second pause and then a pulse
dialed 333-4444 in the first speed dial position

...to store 555-1234 in the second speed dial position

Step 2 - Enter Digits:

1 2 3 4 5 6 # 1 9

9

,7 ,6 3 3 3 4 4 4 4 # 0 0

5 5 5 1 2 3 4 # 0 1

Step 1 -

See Section A

Enter Programming

Enter Programming

Enter Programming

H. Programming Examples

G. DIP Switch Programming/Speaker and Microphone Adjustments

Two POTs are provided to increase or decrease speaker volume and microphone sensitivity. In certain noisy locations
the microphone sensitivity may need to be decreased as shown below. Caution: Setting the microphone gain too high

may cause distorted audio, prevent the distant party from breaking over and inhibit second number redialing.

DIP

Switch

1

1

2

2

3

3

Position

ON

OFF

ON

OFF

ON

OFF

Description

“CALL” button alternately connects and disconnects
calls (factory default)

“CALL” button connects calls only

Incoming calls answered (factory setting)

Incoming calls are not answered

Normal operation mode (factory setting)

Learn mode - Any incoming calls are automatically entered
into the programming mode (no security code required).
Use this option if you have forgotten your security code.

Switch

A

ON

OFF

Description

Normal audio detection

Increase audio detect sensitivity for low level lines. Useful
in applications in which voice or busy signals have trouble
breaking over to the speaker.

Switch

B

ON

OFF

O

N

OFF

A B

O

N

OFF

1 2 3

M

icr

S

ensitivit

ophon

e

S

p

y

eake

V

olume

r