Viking E-1600-ASTIPEWP Quick Start Manual
VIKING
Electronics, Inc.
QUICK START GUIDE
K See Product Manual for complete installation and programming instructions.
1.0 Out-of-Box
1.1 Verify that you have received all of the parts listed
E-1600-ASTIPEWP
VoIP Emergency
Phone
January 15, 2019
X 1
X 1
X 1
X 1
X 8
X 1
Assy Final
Assy Strobe Panel
Chassis E-1600-BLTIPEWP
Torx T-10 Security Bit
Screw Flat head Torx Drive
6-32 x 3/4 Stainless Steel
Black, Red and Green Wires
bundled with Cable Tie
1.2 Download the product manual
Scan the QR code to
open and download
the product manual
- OR -
X 2
X 1
X 2
X 2
X 6
X 1
1. Go to www.vikingelectronics.com and enter
E-1600-ASTIPEWP in the search box
2. Click E-1600-ASTIPEWP in the search results
3. Click Product Manual to open and download
the PDF
Panel Gasket
Hood
5-16 x 2.5 in. Lag Screw
Washer 5/16 Fender
Gel-Filled Butt Connectors
Transformer 12VDC
1.3 Download and install the programming software
1. Go to www.vikingelectronics.com and enter E-1600-ASTIPEWP in the search box
2. Click E-1600-ASTIPEWP in the search results
3. Scroll down the page to Downloads, click IP Programming Software
4. Install the programming software by saving or opening the file and then clicking on
setup Viking IP Programming.exe
5. Follow the prompts on your screen to complete software installation
2.0 Power Source
Select PoE Switch or PoE Injector that meets the following requirements:
1. IEEE 802.3af / 802.3at / 802.3bu compliant
2. Capable of providing at least 4 Watts (class 1)
Note: CAT5e (or higher) cable recommended
3.0 Network Port Settings
• Make sure the port is not in trunk mode
• Make sure port is capable of 100mbps full duplex
• Disable Spanning Tree Protocol (STP) or enable Portfast
4.0 Features Overview
Rear (PCB) View of the Phone Panel
Green Unit Status LED
Yellow Network Status LED:
Lights steady to indicate power
and data link. Blinks to indicate
network activity.
12V DC Adapter
120V AC
(included)
-
Connect to SL-2
+
Strobe Light,
included (see pg 6 in
Product Manual
for proper wiring)
2 Amp Relay
Output Contacts
(2A@30VDC/ 250VAC max)
N.C. (Gray)
COM. (Blue)
N.O. (Yellow)
18E80FXXXXXX
asdesaxtff
MAC:
- Black
+ Red
Black
Black
Red
Red
White
White
- Black
+ Red
PoE LAN Port 10/100, PoE
Class 1 (<4 Watts): Connect
to your LAN via RJ45 plug
and CAT5 or greater twisted
pair wire.
MAC Address Label: The
MAC address is aunique 12
digit number used by routers
to send network traffic to the
correct IP address.
LED
Help Switch
Info Switch (model
E-1600BLT2IPEWP only)
Speaker
Microphone
See the Product Manual for complete installation and programming instructions.
Questions? Call Viking Product Support: 715-386-8666
Due to the dynamic nature of the product design, the information contained in this document is subject to change without notice. Viking Electronics, and its affiliates and/or subsidiaries
assume no responsibility for errors and omissions contained in this information. Revisions of this document or new editions of it may be issued to incorporate such changes.
E-1600-ASTIPEWP Quick Start Guide
ZF303713 REV A
Loading...