Viking Designer DMOC205, Designer DMTK276, Designer DMTK306 Installation Instructions Manual

VIKING RANGE CORPORATION

INSTALLATION

Greenwood, Mississippi 38930 USA

111 Front Street

[phone]

INSTRUCTIONS

DESIGNER SERIES
CONVECTION MICROWAVE BUILT-IN TRIM KIT

Retain for Future Reference

IMPORTANT - PLEASE READ AND FOLLOW

• Before beginning, please read these instructions completely and carefully.

• Be sure to DISCONNECT THE PLUG of the microwave oven from the electrical outlet before installing the built-in trim kit.
Remove the turntable from the oven cavity.

• Because the kit includes metal parts, caution should be used in handling and installation to avoid the possibility of injury.

• Do not remove permanently affixed labels, warnings, or plates from the product. This may void the warranty.

• Please observe all local and national codes and ordinances.

• The installer should leave these instructions with the consumer who should retain for local inspector’s use and for future
reference.

THIS BUILT-IN TRIM KIT IS DESIGNED FOR USE ONLY WITH VIKING CONVECTION MICROWAVE OVENS SPECIFY­ING BUILT-IN TRIM KIT DMTK276 OR DMTK306 FOR DESIGNER UNITS ON THE RATING LABEL ON THE BOTTOM
FACE PLATE OF THE OVEN CAVITY.

IF YOUR LOWER CONVENTIONAL OVEN IS NOT LISTED IN THE USE AND CARE MANUAL OF THE MICROWAVE
OVEN, THEN DO NOT INSTALL THE MICROWAVE OVEN ABOVE IT OR IN ANY AREA WHERE HEAT AND STEAM
ARE GENERATED; FOR EXAMPLE, NEXT TO OR ABOVE A CONVENTIONAL RANGE.

PARTS INCLUDED IN THE KIT

1) Frame Assembly 2) Bottom Duct Assembly

Back Frame

QTY 1

Front Frame

QTY 1

6) Duct A (1)
QTY 1

11) Template: QTY 1

QTY 1

7) Duct A (2)
QTY 1

3) Screw A (1/2" length)
QTY 10

8) Duct A (3)
QTY 1

4) Screw B (1-3/4" length)
QTY 4

9) Duct B
QTY 1

5) Screw C (3/4" length)
QTY 2

10) Duct C
QTY 1

18-11/16"

(47.5 cm)

24-7/8" (63.3 cm)

5"

(12.7 cm)

20-1/8"

(51.1 cm)

11-1/2"

(29.2 cm)

CABINET OR WALL CUTOUT

Provide an opening in the wall or cabinet as indicated in
illustration 1. The depth should be a minimum of 20-1/8"
(51.1 cm). The floor of the opening should be constructed
of plywood strong enough to support the weight of the
oven (about 100 lbs.) and should be level for proper
operation of the oven .

NOTE: While the proper functioning of the oven does not
require that the opening be enclosed (with sides, ceiling
and rear partition), this may be required by local code,
and it is suggested that the local code be checked for
any such requirement.

Illustration 1

ELECTRICAL OUTLET LOCATION

Outlet should NOT be in the shaded area as indicated
on illustration 1. At the rear of the opening, provide a
3-pronged, polarized, electrical outlet, 115-120 volt AC,
15 amp or larger.

EXHAUST DUCT ASSEMBLY

1. Insert the edge of DUCT (B) into the hold lip of DUCT
(C). Secure together by using a SCREW (A) provided in
the kit. Remove the existing screw (#1) at upper right
rear of the oven and secure DUCT (C) with the screw
(#1) just removed from the oven. Secure DUCT (B) with
SCREW (A) through the duct and into the original screw
hole in the oven. See illustration 2.

2. Position DUCT (A)-1 on the top of the oven inserting
edge of DUCT (BC) assembly into hole lip of DUCT
(A)-1. Tighten two SCREWS (A), securing DUCT (A)-1
to DUCT (BC) assembly. See illustration 3.

3. Position DUCT (A)-2 on the top of the oven and insert
it into the hold lip of DUCT (A)-1. Secure DUCT (A)-2
to DUCT (A)-1 using two SCREWS (A) provided. See
illustration 4.

Illustration 2

DUCT B

SCREW A

SCREW A

Illustration 3

SCREW A

DUCT C

#1

DUCT A-1

DUCT BC

SCREW A

4. Position DUCT (A)-3 on top of the oven and insert it
into DUCT (A)-2. Secure DUCT (A)-3 using three screws
(A) provided. See illustration 5.

Illustration 4

SCREW A

DUCT A-1

DUCT A-2

SCREW A

Illustration 5

SCREW A

2

SCREW A

DUCT A-3

SCREW A

DUCT A-2