ViewZ VZ-35SM User Manual

3.5-INCH TFT-LCD
TEST MONITOR

INSTRUCTION MANUAL

Specially made for Surveillance system

- 2 -

Please read the following items before use.

●Dear customers, thanks for using this product, we sincerely hope our products can bring you convenience, and before
start to use it, please pay attention to the following items.
And please keep it after reading the safety notice.

1） Forbidden to use in the high temperature environment especially not allowed in hi-temperature bathroom, the most

suitable working temperature for this product is approximate 0-60℃

If something breaks down, please turn off the monitor, and take out the batteries, or pull out the plug of the charger.
When product leaks smoke 、exception smell or other exception matter . If continue using, it may cause fire disaster or
suffer shock

Don’t redo or knock down the machine (Do not open the case ), if the machine breaks down or the case gets broken.
Please don’t continue using ,otherwise it may cause the fire disaster or suffer shock.

2） Don’t redo、heat up、over-tweak or drag the connection wire, and please don’t put heavy object on the connection

wire, otherwise it may damage the wire, and cause fire disaster or suffer shock. when wire damaged, please contact
the local wholesaler to change.

3） Please don’t place the product in disbalance place, otherwise it may make the machine drop to get damage.
4） Please use the dominated batteries, and when fixing the batteries, please do in accordance with demonstration.

Please don’t heat up 、redo or knock down the battery, please don’t drop the battery or make it get hit, please don’t

place the battery in the metal container. Use the dominated charger to charge the battery. any fails from the above
case may cause battery explosion or leak, thereby cause the fire disaster or body harmness.

5） Please use the dominated battery or AC charger. Please don’t use it at the voltage beyond the fixed range.
6） If battery leaks, and the liquid comes into your eyes、skin or clothes, please wash the position touched, if necessary,

please contact the doctor or dial the emergent number.

7） When plug get damaged or it’s loosen when inserted into the socket, please don’t use the AC charger, otherwise it

may cause fire disaster or suffer shock.

8） Clean the monitor. and when not used for a long time, please take out the batteries, or pull out the plug, otherwise it

may cause fire disaster or suffer shock.

9） When charging finished, please pull out the plug from the socket, otherwise fire disaster may happen.
10） Keep the product away from water or other liquid, otherwise there may be danger of fire disaster or shock.

In order to keep your safety, please use the adapter we supplied (Regarding the damages caused by using adapters

from other supplier, we are not responsible to it).
11） Don’t set the machine in the place of bared sunshine.
12） In order to keep it away from damage by dropping or bumping at sharp object, Please place the machine in

the place where the children can not reach,

When the battery’s working time is apparently shorter than new one, please change the battery.
13） The machine will get heat after long time working, it belongs to normal phenomenon.
14） Please don’t place the charger in the place of much dust or intensity vibration、extreme humidity or high

temperature (for example: under the bare sunshine or beside the heater )

15） The available voltage for the charger is AC 110~240 V / 50/60 Hz. Plug standard is various from different

environment; when purchase this product, please consult relevant department to confirm the suitable plug standard.

16） During charging, the batteries and charger will get heat, it belongs to normal phenomenon, but not

malfunction. If possible, please charge the battery in aeration area.

- 3 -

Battery and power supply

The following items state the right way to use batteries and the way to extend its lifespan Using the batteries in incorrect
way will shorten its lifespan or cause to leak、overheat、fire or explode.

● Battery comes out from factory with no power. Please charge it before use. and put it into the battery box when don’t
use it.

Battery usage notice

-If leaving the battery to be idle, it will lose electricity gradually. Please charge it at 1-2 day early before use

·When battery in idle status, turn off the monitor, it’s a way to extend the lifespan.

·The performance will reduce when battery in low temperature environment; battery can’t work normally in cold

condition. place a fully charged battery in warm place. Don’t place battery close to heater or hand-warming articles.

Charging Notice

·Please put the batteries into the machine,and then connect the charger well.this product adopts IC to conduct electrical
source management.when fit on the battery,it will conduct auto-inspection(the red light flash 2 times),if battery goes
worng,the red light flash quickly;if working normally,the LED indicator light keep red.if fully charged,the red light will
go out.

10 minutes more charging again it’s a way to check if the charged battery is full or not.The charge time will extend if
the surrounding temperature lower than 10℃ or higher than 35℃,please don’t charge the battery in the place where
temperature is higher than 40℃;it stops charging when temperature under 0 ℃.it’s not allowed to charge the fully
charged battery again,and you don’t have to wait to charge until the electricity totally runs out.

·It’a normal phenomenon that battery gets heat when charge over or after use.

Battery’s lifespan

In normal temperature,users can charge battery for 300 times.when the working time of consuming its full capacity
apparently decrease,users need to change the battery.

Storage

·If long time no use after fully charged, the battery’s perfermance will weaken.

·If don’t use this machine for a long time,please take the batteries out,and store them in a dry place，moreover the store
temperature should between 15℃ and 25℃.Please don’t place it in extremely high or low temperature area.

Attention:battery usage notice

-Don’t transport or store the battery together with necklace、barrette and other metal object.

·Don’t throw the battery into fire to heat up.

·Don’t knock down or redo the battery.

·Please use the dominated charger to charge.

·Deal with the batteries discarded.

·Don’t drop the battery or make it suffer intense vibration.

·Please keep it away from water.

·Please keep its connection terminal clean.

·It’s the normal phenomenon that the battery and machine get heat after long time working.

- 4 -

Alternating Current Adapter

·Please just use the adapter dominated for this machine,if use other kind of adapter may cause matters to the machine.

·AC adapter for indoor use.

·Make sure that DC plug connect to the monitor firmly.

·Please turn off the monitor before pull out the plug.

·Don’t use it in other devices.

·Don’t knock it down yourself.

·Don’t place it in high temperature or humidy area.

·Please don’t let it suffer intense shake

·It’s a normal phenomenon that the adapter buzzs or get heat when using.

·If adapter cause wireless interference,please reset the antenna.

Product Use

In order to make sure of the normal working,please don’t let the machine get hit or shake.

Electric interference

This product may cause interference to the medical and aviatic devices.before you use it in the hospital or airport,please
consult the hospital the airline company.

Liquid crystal

If screen suffered damage,please avoid to touch the liquid crystal.if any case of the following happens,please do as we
show.

·If liquid crystal gets to your skin,please clean the position with cloth,then daub some soap and then wash it.

·If liquid crystal comes into your eyes, please flush the eye with water more than 15minutes,and then ask for help from
doctor.

·If drink the liquid crystal by mistake,please gargle with water,and drink much water to help throw up,and then consult
the doctor.

Debug The Machine

Before start to monitor the important spot,please adjust the machine to make sure of its normal working.we are not
responsible to any damage or benefit loss caused by product’s malfunction.

Claim

Specification subject to change without notice, we have the final explaination right to do a explaination to this manual.

·The screen is made from high precise technology,still there would be brightness dot or color abnormity on screen
sometimes.it’s the normal phenomenon to this kind of LCD,but not failure.

·When fall acrosse wireless interference( such as magnetic field、static or circuit noise),the abnormity display may
happen.