Page 1
User Guide
Page 2
1
IMPORTANT SAFETY INSTRUCTIONS:
Please read User Guide before using this product.
Please keep User Guide for future refer ence.
Please read the cautions to prevent possible danger and loss of
property.
FEATURES:
178° Wide viewing angles.
High resolution: 1280× 800.
High brightness: 400cd/㎡.
High contrast: 800:1.
Faster response time.
TALLY interface with indicating light.
Firm & thin design.
CAUTIONS:
1. Please do not place the displ ay scr een towards the ground.
2. Please avoid heavy impact or drop onto the ground.
3. Please do NOT use chemical solutions to clean this product. Please
wipe with a clean soft cloth to maintain the brightness of the surface.
4. Please do not block any vent hole.
5. Please follow the instructions and trouble-shootings to adjust the
product. Other i mprop er adjus tm ent m ay r esult in da mage. Any furt her
adjustment must be performed or conducted by a qualified technician.
6. Please unplug the power if long-ter m no-use, or thunder weather.
Contents
1. PRODUCT DESCRIPTION ................................................................ 2
2. MENU SETTING ................................................................................. 3
3. Software app lic ation ............................................................................. 7
4. ACCESSORIES .................................................................................... 8
5. PARAMETERS ..................................................................................... 8
6. TROUBLE SHOOTING ...................................................................... 8
Page 3
2
1. PRODUCT DESCRIPTION
1． INPUT: circularly switch among of HDMI, YPbPr, Video and SDI.
2． MENU: To activate OSD (on-screen di splay) menu. Press to switch
among the brightness, s harpnes s, c ontras t, s atur atio n, Tint, MENU
and Exit.
3． ◄ Left selection button: to select item on OSD menu and adjust i ts
value; Press to decrease the value of brightness, sharpness,
contrast, saturation and Tint.
4. ► Right selection button: to select item on OSD menu, adjust its
value and confirm it; Press to increase the value of brightness,
sharpness, contrast, saturation and Tint.
5． ENTER.
6． FN: Function button; to launch function menu quick ly.
Note: The interfaces within Monitor 1 provide signal source for monitor 1. The
interfaces within Monitor 2 provide signal source for monitor 2. TALLY
interface, Mini USB interface, power supply inter fac e and LAN port ar e
common interfaces.
1. TALLY interface and interface definiti on.
2. Mini USB input (Only used for program upgrades, do NOT
use if non-professionals).
Page 4
3
3. 12V DC power input.
4. YPbPr input.
5. YPbPr output.
6. Video input. 7. Video output.
8. HDMI input. 9. HDMI output.
10. SDI input. 11. SDI output.
12. The LAN port. (Connected to PC network interface for
function adjustment.)
2. MENU SETTING
Before setting the functions, please make sure the device is
connected correctly.
2-1. Shortcut buttons:
2-1-1. the image menu
Power on, press “◄ / ►” buttons on the device, brightness display bar
will appear at the bottom of the screen, then press the MENU button to
switch among brightness, shar pness , c ontras t, sa turati on, tint, MENU and
Exit. User can adjust the parameters of the selected item with “◄ /
►”buttons to meet their needs.
Page 5
4
ITEMS
OPTIONS
Brightness
0 - 100
Contrast
0 - 100
Saturation
0 – 100
Tint
0 – 100
Sharpness
0 – 100
Color Temp
6500ºK, 7500 ºK, 9300 ºK, User
Red
Note: Available only in
Green
Blue
2-1-2. FN user-definable function button
Press FN button to pop up the defau lt op ti ons, Use “◄ / ►” buttons
to adjust the value of selected item.
Long press FN button for 3-5 seconds to pop up shortcut menu
directly. As shown in right Figure (default menu is
displayed in white font).
Use “◄ / ►” buttons to select the desired item.
Finally, use the “ENTER” button to confirm the
selected item as default.
Functions of FN button can be customized: Center
Marker, Safety Mar ker, C heck F ield, C olor Ba r, A spec t
Ratio, Camera, PIP, Image Flip, Zoom, Pixel-to-Pixel,
Freeze Input, Underscan, H/V delay.
2-2. MENU Operation
Press “MENU” button on the device after power on. The menu used
for setting function will display on the screen.
Press ◄/► buttons to select the sub-menu; then press ENTER to
confirm it; after that, press MENU to return to main menu.
2-2-1. Picture
“User” mode to choose
the color value you ne ed.
Page 6
5
ITEMS
OPTIONS
Center Marker
ON, OFF
Safety Marker
OFF, 95%, 93%, 90%, 88%, 85%, 80%
ITEMS
OPTIONS
Aspect Ratio
Full Screen, 16:9, 4:3, 1.85 :1, 2.3 5:1
H / V delay
OFF, H&V Delay, V Delay, H Delay
Check Field
OFF, Mono, Red, Green, Blue
Pixel-to-Pixel
OFF, ON
Underscan
OFF, ON
Color Bar
OFF, ON
Zoom
OFF, ×2, ×4, ×6, ×8
Image Flip
OFF, ON
Freeze Input
OFF, Freeze
PIP
Small, Medium, Large, PBP, POP
2-2-2. Marker
2-2-3. Display
Page 7
6
2-2-4. DSLR Aux& Audio
ITEMS
OPTIONS
Camera
480P (5D-II Mode), 1080I (5D-
Mode)
Volume
0 – 100
ITEMS
OPTIONS
LOGO
OFF, ON
Language
English, Chinese
Manufacturer Default
OFF, ON
Back Light
0 – 100
ISP
For program upgrades
2-2-5. System
Ⅲ
Page 8
7
3. Software application
1. Cross-connec tion networ k cable
Note：W: white, G: green, O: orange, Bl: blue, Br: brown
2. Software settings
①. Connect the LAN port with PC.
②. Set the PC IP to 192.168.1.XXX network segment(XXX is a
user-definable p ar am e ter ).
③. Open the application program,
then select the monitor which is
needed to be adjusted
(Monitor1or Monitor2).
④. Set the parameter values
according to user's individual
requirements.
First, click the "read" button to
read the corresponding
parameter value of the device to
the software, secondly, modify
the parameter value on the
software, then, the instruction
can be realized on the device.
Page 9
8
4. ACCESSORIES
Panel
7” LED IPS
Physical Resolution
1280×800
Brightness
400 cd/㎡
Contrast
800: 1
Viewing Ang le
178°/ 178°(H/V)
Input Voltage
DC 12V
Input Signal
HDMI, YPbPr, SDI, Video
Power Consumption
≤18W
Operating Temperature
-20℃~60℃
Stor age Temperature
-30℃~70℃
Dimension (LWD)
482.5×133.5×25.3mm
Weight
2885g
1. DC 12V Power adapter 1 piece
2. TALLY connector 1 piece
3. Manual 1 piece
5. PARAMETERS
6. TROUBLE SHOOTING
1. Only black-and-white display:
Check whether the color saturation is properly set up or not.
2. Power on but no pictures:
Check whether the cables of HDMI, YPbPr, SDI and VIDEO are correctly
connected or not. Please use the standard power adapter equipped with
the product package. Improper power input may cause damage.
3. Wrong or abnormal colors:
Check whether the cables are correctly and tightly connected or not.
Broken or loose pins of the cables may cause a bad connection.
4. When power on, the picture shows size error:
Press “MENU → DISPLAY → Underscan” to zoom in/out pictures
automatically when receiving HDMI signals.
5. Other problems:
Please press “MENU” button and choose “SYSTEM→ Manufacturer
Default →ON”, then press "ENTER" button to confirm it.
Page 10
9
6. According to the ISP, the machine can not function properly:
ISP is used for program upgrades, non-professionals do not use. The
device will reboot if selected accidentally!
Note: due to constant effort to improve products and product features,
specifications may change without prior notice.
Page 11
10
Loading...