Page 1
User Guide
Page 2
IMPORTANT SAFETY INSTRUCTIONS:
Please read User Guide before using this product.
Please keep User Guide for future reference.
Please read the cautions to prevent possible danger and loss of
property.
MAIN FEATURES:
3D LUT for Accurate Color Reproduction.
Gamma Selection
Quad Link Square Division and Quad Link 2 Sample Interleave (2SI)
With HDR;
Compare Color Space & Gamma (Side by Side)
SDI and HDMI cross conversion;
Integrated recording info. display;
Various Markers
Various camera assist function : Scan, Aspect, H/V Delay, Check field,
Zoom, Freeze, Waveform, Vector Scope, Time Code, etc.
High resolution: 1920×1200;
Wide voltage: DC 7-24V;
High brightness: 500cd/㎡;
High contrast: 1000:1;
2
Page 3
CAUTIONS:
Please do not place the display screen towards the ground.
Please avoid heavy impact or drop onto the ground.
Please do NOT use chemical solutions to clean this product. Please
wipe with a clean soft cloth to maintain the brightness of the surface.
Please do not block any vent hole.
Please follow the instructions and trouble-shootings to adjust the
product. Other improper adjustment may result in damage. Any further
adjustment must be performed or conducted by a qualified technician.
Please unplug the power and remove the battery if long-term no-use,
or thunder weather.
3
Page 4
Contents
1. PRODUCT DESCRIPTION ................................................................... 5
2. DV BATTERY MOUNT PLATE ........................................................... 7
3. MENU SETTING ................................................................................... 9
4. ACCESSORIES .................................................................................... 20
5. PARAMETERS .................................................................................... 21
6. TROUBLE SHOOTING ....................................................................... 22
4
Page 5
1. PRODUCT DESCRIPTION
1． Power ON/OFF: “○” is power OFF; “|” is power ON.
2． MENU Dial: Turn the dial to adjust volume;
Menu function: press to activate menu displayed on screen when
power on.
Option function: select option via dialing to the left or right.
Confirm function: press to confirm after option selected.
3． EXIT: return/exit; Volume off/on.
4． F1、F2、User-definable buttons.
Default functions: （function customized to meet your needs）
F1 Waveform F2 Scan
5． INPUT: Circularly switch among of SDI and HDMI.
5
Page 6
6． Fan cooling holes.
7． Speaker.
8． SDI input interface.
9． SDI output interface.
10． Earphone jack.
11． USB (3D-LUT load).
12． HDMI output interface.
13． HDMI input interface.
14． DC 12V power input.
6
Page 7
2. DV BATTERY MOUNT PLATE
Standard mounts process
Following three types of battery plates are suitable for this device, model F970
& LP-E6.
MODEL: F-970 MODEL: LP-E6
DV Battery Mount Plate:
DV Battery Mount Plate Specification:
Model F970 for battery of SONY DV:
DCR-TRV series, DCR-TRV E series, VX2100E PD P series, GV-A700,
GV-D800 FD/CCD-SC/TR3/FX1E/HVR-AIC, HDR-FX1000E, HVR-Z1C,
HVR-V1C, FX7E F330.
Model LP-E6 for battery of Canon DSLR:
5D Mark II/5D Mark III/EOS7D/EOS60D;
7
Page 8
Plate Bracket
V-mount Battery Plate
Plate Bracket
Anton Bauer Mount Battery Plate
V-mount battery plate (optional): Please refer to GP-L130AB type
battery specifications.
Anton Bauer mount battery plate (optional): Please refer to GP-
L130B type battery specifications.
8
Page 9
3. MENU SETTING
Before setting the functions, please make sure the device is
connected correctly.
3-1. Shortcut keys:
3-1-1. the image menu
Dialing to the left or right when power on, brightness will appear at the
bottom of the screen, then press the dial to switch among of brightness,
sharpness, contrast, saturation, volume, tint, MENU and Exit. User can
adjust the value of the selected option via the dial.
3-1-2. F1-F2 2 user-definable function buttons:
Long press any F1-F2 key for 3-5 seconds to pop-up
shortcut menu directly. As shown in Figure (default menu
button in white font).
Select option via dialing to the left or right.
Press to confirm option as default, then press EXIT to
exit.
Functions of F1-F2 buttons can also be customized:
Center Marker, Aspect Marker, Check Field, Underscan,
Scan, Aspect, DSLR, Freeze, H/V delay, Peaking, False
Color, Exposure, Histogram, Level Meter, Waveform and
Time Code.
Note: Time code is only available under SDI mode.
F1-F2：2 user-definable function buttons
Default function:
F1 Waveform F2 Scan
9
Page 10
3-2. MENU Operation
When power on, press “MENU”
on the device. The menu of
function setting will display on
the screen.
Dialing left or right toselect a
menu, then press to confirm. The
menu icon presently selected is
shown highlighted.
Dialing left or right to change the setting, then press “MENU”to confirm
the setting. Press EXIT to return.
3-2-1. Picture
3-2-1-1. Brightness
Use this setting to choose the brightness from 0-100.
3-2-1-2. Contrast
Use this setting to choose the contrast from 0-100.
10
Page 11
3-2-1-3. Saturation
Use this setting to choose the saturation from 0-100.
3-2-1-4. Tint
Use this setting to choose the tint from 0 to 100.
3-2-1-5. Sharpness
Use this setting to choose the sharpness from 0 to 100.
3-2-1-6. HDMI RGB Range
Use this setting to choose one of the HDMI RGB Range presets:
[0~255], [16~235].
3-2-1-7. Color Space
Use this setting to choose one of the color space presets: Rec709,
EBU, Native, SMPTE-C.
3-2-1-8. Camera Log
Use this setting to choose one of the camera Log modes:
-[Off]: Sets off Camera Log.
-[Def. Log]
Use this setting to choose one of the Camera Log modes:
SLog2ToLC-709, SLog2ToLC-709TA, SLog2ToSLog2-709,
SLog2ToCine+709, SLog3ToLC-709, SLog3ToLC-709TA,
SLog3ToSLog2-709, SLog3ToCine+709.
-[User Log]
Use this setting to choose one of the User Log modes (1-6).
Pease install the User Log as following steps:
The User Log must be named with .cube in the suffix.
Please note: the device only support the format of User Log:
17x17x17 , Data order is BGR, Table order is BGR.If the format does
not meet the requirement, please use tool “Lut Tool.exe” to transform
it. Naming the User Log as User1~User6.cube, then copy the user
Log into USB flash disk (Only support USD2.0 versions). Insert the
11
Page 12
USB flash disk to the device, the User Log is saved to the device
automatically at the first time. If the User Log is not loaded for the first
time, the device will pop up a prompt message, please choose
whether to update or not.
3-2-1-9. Gamma
Use this setting to choose one of the Gamma tables:
[Off], [1.8], [2.0], [2.2], [2.35], [2.4], [2.6], [2.8].
Note: Gamma mode can be only activated while HDR function closed.
3-2-1-10. HDR
Use this setting to choose one of the HDR presets:
[Off], [ST 2084 300], [ST 2084 1000], [ST 2084 10000], [HLG].
3-2-1-11. Back Light
Use this setting to choose one of the Back Lights modes:
-[Standard]:The default brightness is 100 cd/m².
-[Outdoor]: The default brightness is 500 cd/m².
-[Custom]: Adjusts the level of the back light from 0 to 100.
Note: Only available under [Custom] mode to adjust the level of the
back light.
3-2-1-12. Color Temp
Use this setting to choose one of the color temperature presets:
[5500ºK], [5600ºK],[6500ºK],[7500 ºK], [9300 ºK],[User].
Note:Only available under “User” mode to adjust Color Bias andGain.
12
Page 13
3-2-2. Marker
3-2-2-1. Center Marker
Use this setting to display a center marker on the screen.
3-2-2-2. Aspect Marker
Use this setting to choose the aspect ratio of the marker:
[OFF], [16:9], [1.85:1], [2.35:1], [4:3], [3:2], [1.3X], [2.0X], [2.0X MAG].
3-2-2-3. Safety Marker
Use this setting to set off the safety marker or choose the one of the
safety markers:
[95%], [93%], [90%], [88%], [85%], [80%].
3-2-2-4. Marker Color
Use this setting to choose which color of marker is displayed on the screen.
3-2-2-5. Marker Mat
Use this setting to darken the outside of the aspect marker. It can be
selected from 0-7 (Step value is 1).
3-2-2-6. Thickness
Use this setting to choose the thickness of marker from 0-7 (Step value
is 1).
13
Page 14
3-2-3、Function
SDI Mode HDMI Mode
3-2-3-1. Scan
Use this setting to choose one of the scan modes:
[Zoom], [Aspect], [Pixel To Pixel].
Options can be adjusted only under scan mode.
3-2-3-2. Aspect
Use this setting to choose one of the aspect presets:
[Full], [16:9], [1.85:1], [2.35:1], [4:3], [3:2], [1.3X], [2.0X], [2.0X MAG].
3-2-3-3. Underscan
Use this setting to set off or open the underscan function.
3-2-3-4. H/V Delay
Use this setting to choose one of the H/V modes:
[OFF], [H], [V], [H/V]
3-2-3-5. Check Field
Use the check field modes for monitor calibration or to analyze
individual color components of an image. In Blue, Green and Red
check field modes, only the selected color will be shown.
3-2-3-6. Zoom
14
Page 15
Use this setting to choose zoom scale from 10%-90%(Step value is
10%).
3-2-3-7. Freeze
Choose [Off] or [On] to freeze or unfreeze the current image on the
screen
3-2-3-7. 3G Format
Use this setting to choose one of the 3G Format modes:
[Normal], [GBRA444 10Bit], [YCbCrA444 10Bit],
[YCbCrA422 12Bit], [GBR444 12Bit], [YCbCr444 12Bit].
3-2-3-8. DSLR
Use this setting to choose one of the DSLR modes:
[Off], [5D2], [5D3].
3-2-4. Waveform
3-2-4-1. Waveform
Use this setting to activate or deactivate Waveform. It also can be
choose one of the waveform modes:
[Multi], [Y], [YCbCr], [RGB], [RGB Full].
15
Page 16
3-2-4-2. Waveform Trans
Use this setting to choose the intensity of the WaveformTrans:
-[Off] : The background of waveform is shown at black.
-[25%]:The background of waveform is shown at 25% intensity.
-[50%]:The background of waveform is shown at 50% intensity.
3-2-4-3. Peaking
Use this setting to activate or deactivate the Peaking function.
3-2-4-4. Peaking Color
Use this setting to choose one of the peaking colors:
[Red], [Green], [Blue], [White].
3-2-4-5. Peaking Level
Use this setting to adjust the level of peaking from 0-100.
3-2-4-6. False Color
Use this setting to activate or deactivate the False Color function.
3-2-4-7. Exposure
Use this setting to activate or deactivate the Exposure function
3-2-4-8. Exposure Level
Use this setting to adjust the level of exposure from 0-100.
3-2-4-9. Histogram
Use this setting to choose one of the histogram modes:
[Y], [RGM], [Color].
Select [Off] under Waveform option can deactivate the histogram.
3-2-4-10. Time Code
Use this setting to activate or deactivate the Time Code. It has two
modes of time code to be selected: [LTC], [VITC].
Note: Time code is only available under SDI mode.
16
Page 17
3-2-5. AUDIO
HDMI Mode SDI Mode
3-2-5-1. Volume
Use this setting to adjust the volume from 0-100.
3-2-5-2. Level Meter
Use this setting to activate or deactivate Level Meter function.
Note: Default as on under waveform [Multi] function.
3-2-5-3. Audio Ch
Use this setting to choose one of the Audio Ch modes:
[Ch1&Ch2], [Ch3&Ch4], [Ch5&Ch6], [Ch7&Ch8], [Ch9&Ch10],
[Ch11&Ch12], [Ch13&Ch14], [Ch15&Ch16].
Note: Only available under SDI mode.
17
Page 18
3-2-6. SYSTEM
3-2-6-1. Language
Use this setting to choose one of the Languages: English, Chinese.
3-2-6-2. HDMI/SDI Convert
HDMI/SDI cross conversion function can realize signal transmits from
SDI input to HDMI output and from HDMI input to SDI output.
Use this setting to activate or deactivate the convert function.
3-2-6-3. Color Bar
Use this setting to activate or deactivate the Color Bar function. It has
two modes to be chose when activated: [100%], [75%].
3-2-6-4. OSD Timer
Use this setting to choose the display time of OSD: [10s], [20s], [30s].
3-2-6-5. Image Flip
Use this setting to activate or deactivate the Image Flip function. It has
three modes to be chose: [H], [V], [H/V].
3-2-6-6. Fan
Use this setting to choose the strength of fan: [Low], [High].
18
Page 19
3-2-6-7. Color Calibration
If the device needs to be calibrated color, please operate as following:
Connect the device with the PC via HDMI interface.
Make sure the device and color calibration equipment to work
more than 30 minutes.
After the previous step, activate the Color Calibration function
of the device and color calibration software to calibrate the color
(See the document “CMS Color Calibration Process’ for
details).
It will generate a document “lcd.cube” after calibrated, then
copy this document to USB flash disk.
Insert the USB flash disk to the device and save the document.
This document “lcd.cube” will be found under Color Space
Option.
3-2-6-8. Comparison En
Use this setting to activate or deactivate the Comparison En function.
Activate this function, the screen displays the comparison of Original
image and customized image, as shown.
3-2-6-9. Reset
Select the Reset option, dialing the “Menu”knob to reset automatically.
19
Page 20
4. ACCESSORIES
Standard:
1. Folding sun shade cover 1 piece
2. HDMI A/C cable1 piece
3. Shoe mount 1 piece
4. VESA battery plate 1 piece
5. Battery plate( F970, LP-E6) 2 piece
6. Battery Plate bracket 1 piece
7. 12V DC adapter 1 piece
8. Manual 1 copy
Optional:
1.Anton Bauer mount 1 piece
2. V-mount 1 piece
3. Battery 1 piece
20
Page 21
Aspect Ratio
16:10
Physical Resolution
1920×1200 (324ppi)
Contrast
1000: 1
Viewing Angle
170°/ 170°(H/V)
Input Signal
3G-SDI, HDMI, USB (3D-LUT load)
Power Consumption
≤12W
Dimension (LWD)
182×124×22mm
Weight
405g
5. PARAMETERS
Panel 7”
Brightness
Input Voltage DC 7-24V
Operating Temperature
Storage Temperature
500 cd/㎡
-20℃~60℃
-30℃~70℃
21
Page 22
6. TROUBLE SHOOTING
1. Only black-and-white display:
Check whether the color saturation is properly setup or not.
2. Power on but no pictures:
Check whether the cables of 3G-SDI and HDMI are correctly connected or
not. Please use the standard power adapter coming with the product
package. Improper power input may cause damage.
3. Wrong or abnormal colors:
Check whether the cables are correctly and properly connected or not.
Broken or loose pins of the cables may cause a bad connection.
4. When on the picture shows size error:
Press “MENU → FUNCTION → Underscan” to zoom in/out pictures
automatically when receiving HDMI signals
5. Other problems:
Please press “MENU” button and choose “MENU→SYSTEM→ Reset
→ON”
Note: due to constant effort to improve products and product
features, specifications may change without notice.
22
Loading...